ZnS Nanoseeds Sealed in N, P, S Co-Doped Carbon Hollow Rhombic Dodecahedra as a Superlithiophilic Host for Dendrite-Free Lithium Metal Anodes.

Lithium (Li) metal is considered a hopeful anode for next-generation Li-ion batteries thanks to its ultra-high theoretical specific capacity, extra-low theoretical density, and low negative potential. However, the uncontrolled growth of Li dendrites and volume fluctuation during plating/stripping processes severely hamper its commercial application. Herein, ZnS seeds sealed in N, P, S co-doped carbon hollow rhombic dodecahedra (ZnS@NPS-C HRD) is fabricated as a superlithiophilic host for Li metal anodes (LMAs) to solve the above problems. In addition, the Li nucleation and deposition mechanism on ZnS@NPS-C HRD is investigated by in situ optical microscopy, ex-situ X-ray diffraction, scanning electron microscopy, and theoretical calculations. Owing to the synergistic strategy of ZnS seeds-inducing nucleation and Li-limited growth, the as-prepared composite exhibits stability for 300 cycles in asymmetric cells and a long lifespan over 1100 h in symmetric cells. Moreover, the ZnS@NPS-C HRD@Li|LiFePO4 full cell demonstrates a reversible capacity of 100.91 mAh g-1 after 400 cycles at 1 C.

Roles of soluble minerals in Cd sorption onto rice straw biochar.

Transforming to biochar provides an environmentally friendly approach for crop residue reutilization, which are usually applied as sorbent for heavy metal removal. As typical silicon-rich material, the specific sorptive mechanisms of rice straw derived biochar (RSBC) are concerned, especially at the low concentration range which is more environmentally relevant. In the present study, Cd sorption onto RSBCs at the concentration of ≤ 5 mg/L was investigated. The sorptive capacity was positively correlated with the pyrolytic temperature of the biochar and the environmental pH value. Water soluble minerals of the RSBCs played the dominant roles in Cd sorption, contributing 29.2%, 62.5% and 82.9% of the total sorption for RSBCs derived under 300°C, 500°C and 700°C, respectively. Increased number of cations, dominantly K+, were exchanged during the sorption. Coprecipitation with cations and carbonates may also be contributive to the sorption. The dissolution of silicon-containing minerals was found to be declined during sorption, suggesting its involvement in the sorption process, possibly through precipitation. Whilst, the sparingly soluble silicate crystals may impose ignorable role in the sorption. Complexation with organic groups is only a minor mechanism in Cd sorption, compared to the much more dominant roles of the inorganic ashes.

3D printed PLGA/MgO/PDA composite scaffold by low-temperature deposition manufacturing for bone tissue engineering applications.

Introduction: Bones are easily damaged. Biomimetic scaffolds are involved in tissue engineering. This study explored polydopamine (PDA)-coated poly lactic-co-glycolic acid (PLGA)-magnesium oxide (MgO) scaffold properties and its effects on bone marrow mesenchymal stem cells (BMSCs) osteogenic differentiation. Methods: PLGA/MgO scaffolds were prepared by low-temperature 3D printing technology and PDA coatings were prepared by immersion method. Scaffold structure was observed by scanning electron microscopy with an energy dispersive spectrometer (SEM-EDS), fourier transform infrared spectrometer (FTIR). Scaffold hydrophilicity, compressive/elastic modulus, and degradation rates were analyzed by water contact angle measurement, mechanical tests, and simulated-body fluid immersion. Rat BMSCs were cultured in scaffold extract. Cell activity on days 1, 3, and 7 was detected by MTT. Cells were induced by osteogenic differentiation, followed by evaluation of alkaline phosphatase (ALP) activity on days 3, 7, and 14 of induction and Osteocalcin, Osteocalcin, and Collagen I expressions. Results: The prepared PLGA/MgO scaffolds had dense microparticles. With the increase of MgO contents, the hydrophilicity was enhanced, scaffold degradation rate was accelerated, magnesium ion release rate and scaffold extract pH value were increased, and cytotoxicity was less when magnesium mass ratio was less than 10%. Compared with other scaffolds, compressive and elastic modulus of PLGA/MgO (10%) scaffolds were increased; BMSCs incubated with PLGA/MgO (10%) scaffold extract had higher ALP activity and Osteocalcin, Osteopontin, and Collagen I expressions. PDA coating was prepared in PLGA/MgO (10%) scaffolds and the mechanical properties were not affected. PLGA/MgO (10%)/PDA scaffolds had better hydrophilicity and biocompatibility and promoted BMSC osteogenic differentiation. Conclusion: Low-temperature 3D printing PLGA/MgO (10%)/PDA scaffolds had good hydrophilicity and biocompatibility, and were conducive to BMSC osteogenic differentiation.

The pH-sensitive sorption governed reduction of Cr(VI) by sludge derived biochar and the accelerating effect of organic acids.

Reduction coupling immobilization is one of the most commonly adopted strategies for the remediation of Cr(VI) contamination. Biochar is a carbon-rich material with abundant active functional groups for sorption and reduction reactions. In previous reports, phytomass derived biochars and organic functional groups have been emphasized, while the performance of sludge derived biochar (SBC) has often been understated. In the present study, a 30 d kinetic study proved that the removal route involved the sorption of Cr(VI), reduction to Cr(III) and immobilization of Cr(III), and that the sorption process was the primary and rate determining step. As a result of the SBC alkalinity, the solution pH increased, and sorption was largely inhibited, which then governed the overall removal ratio. The FTIR spectra suggested the involvement of hydroxyls in these processes. Low molecular weight organic acids accelerated the removal process in the early phase and improved the reduction process.

A 3D-printed bioactive polycaprolactone scaffold assembled with core/shell microspheres as a sustained BMP2-releasing system for bone repair.

Integration of biological factors and hierarchical rigid scaffolds is of great interest in bone tissue engineering for fabrication of biomimetic constructs with high physical and biological performance for enhanced bone repair. Core/shell microspheres (CSMs) delivering bone morphogenetic protein-2 (BMP-2) and a strategy to integrate CSMs with 3D-printed scaffolds were developed herein to form a hybrid 3D system for bone repair. The scaffold was printed with polycaprolactone (PCL) and then coated with polydopamine. Shells of CSMs were electrosprayed with alginate. Cores were heparin-coated polylactic acid (PLA) microparticles fabricated via simple emulsion and heparin coating strategy. Assembly of microspheres and scaffolds was realized via a self-locking method with the assistance of controlled expansion of CSMs. The hybrid system was evaluated in the rat critical-sized bone defect model. CSMs released BMP-2 in a tunable manner and boosted osteogenic performance in vitro. CSMs were then successfully integrated inside the scaffolds. The assembled system effectively promoted osteogenesis in vitro and in vivo. These observations show the importance of how BMP-2 is delivered, and the core/shell microspheres represent effective BMP-2 carriers that could be integrated into scaffolds, together forming a hybrid system as a promising candidate for enhanced bone regeneration.