Effect of coffee thermocycling on the surface roughness and stainability of denture base materials with different chemical compositions manufactured with additive and subtractive technologies.

OBJECTIVE: To evaluate the effect of coffee thermocycling (CTC) on the surface roughness (Ra ) and stainability of denture base materials with different chemical compositions fabricated by using additive and subtractive manufacturing. MATERIALS AND METHODS: Disk-shaped specimens were additively (FREEPRINT denture, AM) or subtractively (G-CAM, GSM and M-PM, SM) fabricated from three pink denture base materials in different chemical compositions (n = 10). Ra was measured before and after polishing, while color coordinates were measured after polishing. Specimens were subjected to CTC (5000 cycles) and measurements were repeated. Color differences (ΔE00 ) after CTC were calculated. Ra among different time intervals within materials was evaluated by using repeated measures analysis of variance (ANOVA), while 1-way ANOVA was used to evaluate the Ra of different materials within each time interval and the ΔE00 values. Color coordinates within each material were compared by using paired samples t-tests (α = 0.05). RESULTS: Ra before polishing was the highest for all materials (p < 0.001), while SM had its lowest Ra after CTC and AM had its lowest Ra after polishing (p ≤ 0.008). Before polishing, AM had the highest Ra among the materials (p < 0.001). After polishing, SM had higher Ra than AM (p < 0.001). After CTC, GSM had the lowest Ra (p ≤ 0.048). SM had the lowest (p ≤ 0.031) and AM had the highest (p < 0.001) ΔE00 . CTC decreased the a* and b* values of SM and AM (p ≤ 0.017), and increased the L* values of AM (p < 0.001). CONCLUSIONS: Polishing significantly reduced the surface roughness of all materials. CTC did not increase the surface roughness of materials above the clinically acceptable threshold. Only AM had perceptible color change when previously reported threshold values for denture base materials were considered. CLINICAL SIGNIFICANCE: Tested denture base materials may have similar surface stability after coffee thermocycling. However, subtractively manufactured denture base materials may have improved color stability when subjected to long-term coffee consumption.

Stainability and translucency of potassium aluminum sulfate applied computer-aided design and computer-aided manufacturing materials after coffee thermocycling.

OBJECTIVE: The purpose of this in vitro study was to evaluate the effect of potassium aluminum sulfate (alum) application on the stainability and translucency of computer-aided design and computer-aided manufacturing (CAD-CAM) materials after coffee thermocycling (CTC). MATERIALS AND METHODS: Disk-shaped specimens (Ø10 × 1 mm; N = 200) were fabricated by using additively (Crowntec [CT] and Varseo Smile Crown Plus [VS]) and subtractively manufactured (Brilliant Crios [RCR], CEREC Block [FC], and Vita Enamic [VE]) CAD-CAM materials and polished. All specimens were randomly divided into two groups as alum applied and control (n = 10). All specimens were then subjected to CTC (10,000 cycles at 5-55°C) and color coordinates were measured at each time interval. Color differences (ΔE00 ) and relative translucency parameters (RTPs) were calculated and the data were statistically analyzed (a = 0.05). RESULTS: Among tested time intervals, alum applied specimens had their lowest ΔE00 after alum application (p ≤ 0.006), except for FC (p = 0.177). In addition, alum applied RCR had lower ΔE00 values than its control specimens (p = 0.029). Alum applied specimens had their lowest RTP after CTC (p < 0.001) and alum application decreased the RTP of CT (p = 0.010). CTC reduced the RTP of all materials in control groups (p < 0.001). Alum applied CT had higher RTP than its control specimens (p = 0.049). CONCLUSIONS: Alum application's effect on color change varied depending on the material and alum mostly resulted in clinically acceptable changes in translucency. CTC led to unacceptable color and translucency changes based on previously reported threshold values. CLINICAL SIGNIFICANCE: Optical properties of CAD-CAM materials and the sustainability of these properties over time is critical for longevity. Alum may improve the color stability of reinforced composite resin when subjected to long-term coffee consumption.

Effect of preparation design on the fracture resistance and fracture patterns of 3D printed one-piece endodontic crowns.

STATEMENT OF PROBLEM: The impact of various preparation designs on the fracture resistance and fracture type of mandibular premolars restored with 3 dimensionally (3D) printed, 1-piece endodontic crowns remains unclear. PURPOSE: The purpose of this study was to investigate the effect of different preparation designs on the fracture resistance and fracture patterns of mandibular premolars restored with 3D printed 1-piece endodontic crowns after thermal aging. MATERIAL AND METHODS: Forty-five freshly extracted mandibular premolars received 3 different preparation designs: with at least 2 intact cuspal walls (2CW), with only 1 intact cuspal wall (1CW), and no cuspal wall present (NoCW). One-piece endodontic crowns were designed by using a computer-aided design (CAD) software program, 3D printed, cemented to the prepared teeth with self-adhesive resin cement, and thermocycled between 5 °C and 55 °C in artificial saliva. Subsequently, all specimens were subjected to a fracture test. The results were statistically analyzed using 1-way ANOVA (α=.05), and fracture types of all specimens were examined using a light microscope. RESULTS: The analysis of fracture resistance values across separate designs revealed no statistically significant differences (P>.05). Mean fracture resistance values were 724.5 N in 2CW, 713 N in 1CW, and 861 N in NoCW. In 2CW and 1CW, the 1-piece endodontic crowns mostly displayed Type III fractures, whereas those in NoCW exhibited a combination of Type II and Type III fractures. CONCLUSIONS: The mandibular premolar 1-piece endodontic crowns tested in this study exhibited similar fracture resistance and type of fracture with different preparation designs.

Influence of intraoral scanner and finish line location on the fabrication trueness and margin quality of additively manufactured laminate veneers fabricated with a completely digital workflow.

STATEMENT OF PROBLEM: Knowledge of the fabrication trueness and margin quality of additively manufactured (AM) laminate veneers (LVs) when different intraoral scanners (IOSs) and finish line locations are used is limited. PURPOSE: The purpose of this in vitro study was to evaluate the fabrication trueness and margin quality of AM LVs with different finish line locations digitized by using different IOSs. MATERIAL AND METHODS: An LV preparation with a subgingival (sub), equigingival (equi), or supragingival (supra) finish line was performed on 3 identical maxillary right central incisor typodont teeth. Each preparation was digitized by using 2 IOSs, (CEREC Primescan [PS] and TRIOS 3 [TS]), and a reference LV for each finish line-IOS pair (n=6) was designed. A total of 90 LVs were fabricated by using these files and urethane acrylate-based definitive resin (Tera Harz TC-80DP) (n=15). Each LV was then digitized by using PS to evaluate fabrication trueness (overall, external, intaglio, and marginal surfaces). Each LV was also qualitatively evaluated under a stereomicroscope (×60), and the cervical and incisal margin quality was graded. Fabrication trueness and cervical margin quality were evaluated by using 2-way analysis of variance, while Kruskal-Wallis and Mann Whitney-U tests were used to evaluate incisal margin quality (α=.05). RESULTS: The interaction between the IOS type and the finish line location affected measured deviations at each surface (P≤.020). PS-sub and TS-supra had higher overall trueness than their counterparts. and the subgingival finish line resulted in the lowest trueness (P≤.005). PS and the subgingival finish line led to the lowest trueness of the external surface (P≤.001). TS-sub had the lowest intaglio surface trueness among the TS subgroups, and PS-sub had higher trueness than TS-sub (P<.001). PS-sub and PS-supra had higher marginal surface trueness than their TS counterparts (P<.001). TS resulted in higher cervical margin quality (P=.001). CONCLUSIONS: Regardless of the IOS tested, subgingival finish lines resulted in the lowest trueness. The effect of IOS on the measured deviations varied according to the surface evaluated and finish line location. The cervical margin quality of AM LVs was higher when TS was used.

Influence of scan extension and starting quadrant on the accuracy of four intraoral scanners for fabricating tooth-supported crowns.

STATEMENT OF PROBLEM: Multiple factors can influence the accuracy of intraoral scanners (IOSs). However, the impact of scan extension and starting quadrant on the accuracy of IOSs for fabricating tooth-supported crowns remains uncertain. PURPOSE: The purpose of the present in vitro study was to measure the influence of scan extension (half or complete arch scan) and the starting quadrant (same quadrant or contralateral quadrant of the location of the crown preparation) on the accuracy of four IOSs. MATERIAL AND METHODS: A typodont with a crown preparation on the left first molar was digitized (T710) to obtain a reference scan. Four scanner groups were created: TRIOS 5, PrimeScan, i700, and iTero. Then, 3 subgroups were defined based on the scan extension and starting quadrant: half arch (HA subgroup), complete arch scan starting on the left quadrant (CA-same subgroup), and complete arch scan starting on the right quadrant (CA-contralateral subgroup), (n=15). The reference scan was used as a control to measure the root mean square (RMS) error discrepancies with each experimental scan on the tooth preparation, margin of the tooth preparation, and adjacent tooth areas. Two-way ANOVA and pairwise multiple comparisons were used to analyze trueness (α=.05). The Levene and pairwise comparisons using the Wilcoxon Rank sum tests were used to analyze precision (α=.05). RESULTS: For the tooth preparation analysis, significant trueness and precision differences were found among the groups (P<.001) and subgroups (P<.001), with a significant interaction group×subgroup (P=.002). The iTero and TRIOS5 groups obtained better trueness than the PrimeScan and i700 groups (P<.001). Moreover, half arch scans obtained the best trueness, while the CA-contralateral scans obtained the worst trueness (P<.001). The iTero group showed the worst precision among the IOSs tested. For the margin of the tooth preparation evaluation, significant trueness and precision differences were found among the groups (P<.001) and subgroups (P<.001), with a significant interaction group×subgroup (P=.005). The iTero group obtained best trueness (P<.001), but the worst precision (P<.001) among the IOSs tested. Half arch scans obtained the best trueness and precision values. For the adjacent tooth analysis, trueness and precision differences were found among the groups (P<.001) and subgroups tested (P<.001), with a significant interaction group×subgroup (P=.005). The TRIOS 5 obtained the best trueness and precision. Half arch scans obtained the best accuracy. CONCLUSIONS: Scan extension and the starting quadrant impacted the scanning trueness and precision of the IOSs tested. Additionally, the IOSs showed varying scanning discrepancies depending on the scanning area assessed. Half arch scans presented the highest trueness and precision, and the complete arch scans in which the scan started in the contralateral quadrant of where the crown preparation was obtained the worst trueness and precision.

Effect of barium silicate on mechanical properties, transmittance, and protein adsorption of resin for additive manufacturing containing zwitterionic polymer.

STATEMENT OF PROBLEM: Studies on the effect of barium silicate on the material properties of additively manufactured (AM) resins containing 2-methacryloyloxyethyl phosphorylcholine (MPC) for dental applications are lacking. PURPOSE: The purpose of this in vitro study was to evaluate the mechanical properties, transmittance, and protein adsorption of MPC-containing AM resin incorporated with different barium silicate contents and to compare these findings with those of a commercially available unfilled AM resin marketed for definitive restorations. MATERIAL AND METHODS: Resins incorporating 6 wt% MPC and 4 different concentrations of barium silicate (10 wt%, MB10; 20 wt%, MB20; 30 wt%, MB30; and 40 wt%, MB40) were prepared. An MPC-containing resin with no filler was also prepared (0 wt%, MBN). Surface roughness (n=15), Vickers hardness (n=15), flexural strength and modulus (n=15), fracture toughness (n=15), transmittance (n=15), and protein adsorption (n=3) of the filled resin specimens were measured and compared with those of commercially available unfilled resin specimens. All data were analyzed using the Kruskal-Wallis and Dunn tests (α=.05). RESULTS: All experimental resins had higher surface roughness than the unfilled resin (P≤.048). MB40 had higher hardness, flexural strength, flexural modulus, and fracture toughness than most other groups (P≤.047). MB10 had higher transmittance than most other groups (P≤.012). All experimental resins had lower protein adsorption than the unfilled resin, regardless of the barium silicate content (P≤.023). CONCLUSIONS: The experimental resin containing 6 wt% MPC and 40 wt% barium silicate showed better mechanical properties and lower protein adsorption than the resin with no MPC or ceramic fillers. Transmittance decreased with the increase of barium silicate in the resins.

Cameo and intaglio surface stability and variability of additively, subtractively, and conventionally manufactured occlusal devices after long-term storage.

STATEMENT OF PROBLEM: Additive and subtractive manufacturing have become alternative technologies for fabricating occlusal devices. However, knowledge of the long-term stability of occlusal devices fabricated using these recent technologies is limited. PURPOSE: The purpose of this in vitro study was to evaluate the cameo and intaglio surface stability and variability of additively, subtractively, and conventionally manufactured occlusal devices after 18 months of storage. MATERIAL AND METHODS: A standard tessellation language (STL) file of a dentate maxillary typodont was used to design a master occlusal device. The STL file of this design was used to fabricate occlusal devices additively either with a digital light processing (AM-1) or a continuous liquid interface production (AM-2) printer, subtractively with 2 different 5-axis milling units (SM-1 and SM-2), and conventionally (TM-HP) (n=10). STL files of each device's cameo and intaglio surfaces were generated using a laboratory scanner after fabrication and after 18 months of storage in a moist environment. These generated files were imported into an analysis software program (Geomagic Control X) to analyze the dimensional stability of tested devices by using the root mean square method. The average deviation values defined the variability of measured changes over time. Cameo and intaglio surface deviations were analyzed using the Kruskal-Wallis and Dunn tests, while the variability of measured deviations was analyzed with 1-way analysis of variance and the Tukey HSD tests (α=.05). RESULTS: Significant differences were observed among tested devices when the intaglio surface deviations and the cameo surface variability were considered (P<.001). SM-2 had significantly higher intaglio surface deviations than AM-1, SM-1, and AM-2 (P≤.036). Among the test groups, AM-1 had the greatest cameo surface variability (P≤.004). CONCLUSIONS: SM-2 resulted in lower intaglio surface stability than the additive and the other subtractive manufacturing technologies, while AM-1 led to the highest cameo surface variability among the test groups.

Fatigue behavior of implant-supported cantilevered prostheses in recently introduced CAD-CAM polymers: An in vitro study.

STATEMENT OF PROBLEM: Cantilevered complete arch implant-supported prostheses are commonly fabricated from zirconia and more recently from strength gradient zirconia. Different polymer-based materials indicated for definitive fixed prostheses that could be used with additive or subtractive manufacturing have also been marketed recently. However, knowledge on the long-term fatigue behavior of cantilevered implant-supported prostheses made from these polymer-based materials and strength gradient zirconia is lacking. PURPOSE: The purpose of this in vitro study was to evaluate the fatigue behavior of implant-supported cantilevered prostheses of recently introduced computer-aided design and computer-aided manufacturing polymers and zirconia. MATERIAL AND METHODS: A master standard tessellation language file of a 9×11×20-mm specimen with a titanium base (Ti-base) space that represented an implant-supported cantilevered prosthesis was used to fabricate specimens from additively manufactured interim resin (AM), polymethyl methacrylate (SM-PM), nanographene-reinforced polymethyl methacrylate (SM-GR), high-impact polymer composite resin (SM-CR), and strength gradient zirconia (SM-ZR) (n=10). Each specimen was prepared by following the respective manufacturer's recommendations, and Ti-base abutments were cemented with an autopolymerizing luting composite resin. After cementation, the specimens were mounted in a mastication simulator and subjected to 1.2 million loading cycles under 100 N at 1.5 Hz; surviving specimens were subjected to another 1.2 million loading cycles under 200 N at 1.5 Hz. The load was applied to the cantilever extension, 12-mm from the clamp of the mastication simulator. The Kaplan-Meier survival analysis and Cox proportional hazards model were used to evaluate the data (α=.05). RESULTS: Significant differences in survival rate and hazard ratio were observed among materials (P<.001). Among tested materials, SM-ZR had the highest and AM had the lowest survival rate (P≤.031). All materials had a significantly higher hazard ratio than SM-ZR (P≤.011) in the increasing order of SM-GR, SM-PM, SM-CR, and AM. CONCLUSIONS: SM-ZR had the highest survival rate with no failed specimens. Even though most of the tested polymer-based materials failed during cyclic loading, these failures were commonly observed during the second 1.2 million loading cycles with 200 N. All materials had a higher hazard ratio than SM-ZR.

Implementation of triple-scan protocol to evaluate the fit of complete-arch implant-supported fixed prostheses.

Passive fit is essential for multiple-unit implant-supported prostheses. Conventional methods to assess the passivity of complete-arch implant-supported prostheses do not allow 3-dimensional (3D) visualization and quantification of misfit. This report describes the marginal and internal fit evaluation of a complete-arch implant-supported prosthesis by using the triple-scan protocol involving a scanner and a 3D analysis freeware. This technique allows researchers, clinicians, or dental technicians to detect and quantify 3D prosthetic misfit, which may facilitate the preparation for dental appointments and objective measurement of misfit for research studies.

In vitro evaluation of the impact of intraoral scanner, scanning aids, and the scanned arch on the scan accuracy of edentulous arches.

PURPOSE: To assess the accuracy of complete maxillary and mandibular edentulous arch scans obtained using two different intraoral scanners (IOSs), with and without scanning aids, and to compare these results to those obtained using conventional impression methods. MATERIALS AND METHODS: Two IOSs were used (TRIOS 4 [TRI] and Emerald S [EMR]) to scan maxillary and mandibular typodonts. The typodonts were scanned without scanning aids [TRI_WSA and EMR_WSA groups] (n = 10). The typodonts were then scanned under four scanning aid conditions (n = 10): composite markers [TRI_MRK and EMR_MRK groups], scanning spray [TRI_SPR and EMR_SPR groups], pressure indicating paste [TRI_PIP and EMR_PIP groups], and liquid-type scanning aid [TRI_LQD and EMR_LQD groups]. Conventional impressions of both arches were also made using irreversible hydrocolloids in stock trays [IHC] and using polyvinyl siloxane (PVS) impression material in custom trays (n = 10) which were digitized using a laboratory scanner. Using a metrology software program, all scans were compared to a reference scan in order to assess trueness and to each other to assess precision. Trueness and precision were expressed as the root mean square (RMS) of the absolute deviation values and the statistical analysis was modeled on a logarithmic scale using fixed-effects models to meet model assumptions (α = 0.05). RESULTS: The main effect of arch (p = 0.004), scanner (p < 0.001), scanning aid (p = 0.041), and the interaction between scanner and scanning aid (p = 0.027) had a significant effect on mean RMS values of trueness. The arch (p = 0.015) and scanner (p < 0.001) had a significant effect on the mean RMS values of precision. The maxillary arch had better accuracy compared to the mandible. The TRIOS 4 scanner had better accuracy than both the Emerald S scanner and conventional impressions. The Emerald S had better precision than conventional impressions. The scanning spray and liquid-type scanning aids produced the best trueness with the TRIOS 4 scanner, while the liquid-type scanning aid and composite markers produced the best trueness for the Emerald S scanner. CONCLUSION: The scanned arch and the type of scanner had a significant effect on the accuracy of digital scans of completely edentulous arches. The scanning aid had a significant effect on the trueness of digital scans of completely edentulous arches which varied depending on the scanner used.

Verifying the seating of a 3D-printed removable die using elastomeric matrices: A dental technique.

Computer-aided design and computer-aided manufacturing systems enable digital designing and 3-dimensional (3D) printing of definitive casts with removable dies. However, the fit of the removable dies should be without interferences for their accurate positioning in the cast. Given that the accuracy of additive manufacturing depends on design- and manufacturing-related factors, verifying the accuracy of the position of 3D-printed removable dies in their cast is essential to fabricate positionally accurate definitive prostheses, which would enable minimal or no laboratory and clinical adjustments. This dental technique article presents a straightforward approach to verify the seating of a 3D-printed removable die by using verification matrices made of a polyvinylsiloxane interocclusal registration material.

Influence of drilling sequence and guide-hole design on the accuracy of static computer-assisted implant surgery in extraction sockets and healed sites-An in vitro investigation.

OBJECTIVES: To evaluate the effect of drilling sequence, guide-hole design, and alveolar ridge morphology on the accuracy of implant placement via static computer-assisted implant surgery (sCAIS). MATERIALS AND METHODS: Standardized maxillary bone models including single-tooth gaps with fresh extraction sockets or healed alveolar ridge morphologies were evaluated in this study. Implants were placed using different drilling sequences (i.e., complete [CDS] or minimum [MDS]), and guide-hole designs (i.e., manufacturer's sleeve [MS] or sleeveless [SL] guide-hole designs). The time for implant placement via sCAIS procedures was also recorded. The angular, crestal, and apical three-dimensional deviations between planned and final implant positions were digitally obtained. Statistical analyses were conducted by a non-parametric three-way ANOVA (α = .05). RESULTS: Based on a sample size analysis, a total of 72 implants were included in this study. Significantly higher implant position accuracy was found at healed sites compared to extraction sockets and in SL compared to MS guide-hole design in angular, crestal, and apical 3D deviations (p ≤ .048). A tendency for higher accuracy was observed for the CDS compared to the MDS, although the effect was not statistically significant (p = .09). The MDS required significantly shorter preparation times compared with CDS (p < .0001). CONCLUSION: Implant placement via sCAIS resulted in higher accuracy in healed sites than extraction sockets, when using SL compared to MS guides, and tended to be more accurate when using CDS compared to MDS. Therefore, even though surgery time was shorter with MDS, its use should be limited to strictly selected cases.

Effect of internal connection type and screw channel angle on the screw stability of anterior implant-supported zirconia crowns.

OBJECTIVES: To investigate the effect of implant-abutment connection and screw channel angle on screw stability by comparing a newly introduced and an established connection, before and after cyclic loading. MATERIALS AND METHODS: Implants (N = 44) with Torcfit (TF) or Crossfit (CF) connection were divided to be restored with a straight (CFS and TFS) or an angled screw access channel (CFA and TFA) titanium-base abutment (n = 11). CFA and TFA received screw-retained crowns, whereas CFS and TFS received hybrid zirconia abutments and cement-retained crowns. The initial torque value (ITV) of each complex (ITVI ) and removal torque value (RTV) after 24 h (RTVI ) were measured. Screws were replaced with new ones, ITVs were recorded again (ITVF ), and crowns were cyclically loaded (2.4 million cycles, 98 N) to measure RTVs again (RTVF ). Percentage torque loss was calculated. Data were analyzed (α = 0.05). RESULTS: ITVs were similar among groups (p ≥ .089). CF led to higher RTVs (p ≤ .002), while CFS had higher RTVI than CFA (p = .023). After 24 h, CFS had lower percentage torque loss than TF, while CFA had lower percentage torque loss than TFA (p ≤ .011). After cyclic loading, CF led to lower percentage torque (p < .001). CONCLUSION: The implant-abutment connection affected the removal torque values. However, no screw loosening occurred during cyclic loading, which indicated a stable connection for all groups. Screw access channel angle did not affect screw stability after cyclic loading.

Accuracy of implant placement in the posterior maxillary region depending on the alveolar residual bone height and sinus morphology: An in vitro study.

OBJECTIVES: The primary aim of this in vitro study was to assess the effect of alveolar residual bone height in the posterior maxilla on the accuracy of the final implant position via free-handed and static Computer-Assisted Implant Placement (sCAIP). The secondary aim was to evaluate the influence of the maxillary sinus morphology on the accuracy of final implant position. MATERIALS AND METHODS: Partially edentulous standardized maxillary models simulating three different residual bone heights and different sinus floor morphologies were investigated. One-hundred eighty equally distributed implants, which were placed either free-handed or sCAIP, constituted the study sample. 3D digital deviations were obtained by superimposing the post-surgical scans on the initial treatment plan. RESULTS: Angular and linear deviation assessment demonstrated higher implant position accuracy in the sCAIP group. sCAIP revealed similar outcomes independently of the alveolar bone height and sinus floor morphology. Contrarily, in the free-handed group, alveolar bone height and sinus morphology statistically affected the final implant position. Non-parametric three-way ANOVA showed significance for implant placement protocol (p < .0001) and alveolar bone height (p ≤ .02) when angular, and linear deviations were evaluated. Sinus morphology was statistically significantly associated with angular deviation (p = .0009). CONCLUSIONS: sCAIP demonstrated higher 3D implant position accuracy. Alveolar bone height (strongly) and sinus morphology are associated with the accuracy of final implant position when the free-handed implant protocol is followed. However, these anatomical factors did not affect final implant position during sCAIP.

Design, development and validation of a questionnaire to assess dentists' knowledge and experience in diagnosing, recording, and managing root caries.

OBJECTIVES: The prevalence of root caries is increasing globally, especially in the elderly population, and even though the number of patients with root caries lesions is augmenting, there are still many discrepancies in how dentists manage this condition. The present study aimed to develop and validate a questionnaire to evaluate how dentists diagnose, record and manage root caries lesions, and to verify the validity and reliability of this questionnaire. MATERIALS AND METHODS: An expert panel developed a self-administered questionnaire survey with three domains: (1) dentists' knowledge on diagnosis, recording, and managing root caries; (2) information about their current general clinical routines; (3) their demographics. The original English [E] version was translated into three different languages (French [F], German [G], Italian [I]), and subsequently back-translated into English by independent dentists. For the validation, 82 dentists (20-22 for each of the translated versions) accepted to answer the questionnaire at two different time-points (with 1-week interval). The data was quality checked. Construct validity, internal reliability, and intra-class correlation (ICC) were assessed. RESULTS: Seventy-seven dentists completed the questionnaire twice [E: 17; F: 19; G: 19; I: 22]. The mean ICC (standard deviation) was 0.98(0.03) for E, 0.90(0.12) for F, 0.98 (0.04) for G, and 0.98 (0.01) for I. Overall, the test-retest reliability was excellent (mean ICC (SD): 0.96 (0.08)). Furthermore, the questionnaire demonstrated good internal reliability (inter-observer reliability; Fleiss kappa: overall:0.27(fair); E:0.30 (fair); F: 0.33(fair); G: 0.33(fair); I: 0.89 (almost perfect)). CONCLUSION: The questionnaire was validated and is suitable to be used in the four languages to assess the knowledge of dentists on diagnosing, recording and managing root caries. CLINICAL SIGNIFICANCE: The present questionnaire was validated and seems to be a good tool to evaluate how dentists diagnose, record, and manage root caries lesions both in its original (English) and its translated (French, German, and Italian) versions.

Patient-reported outcome measures focusing on the esthetics of implant-compared to tooth-supported single crowns-A systematic review and meta-analysis.

OBJECTIVES: To report a summary of published patient-reported esthetic outcome measures (PROMs) of implant-supported single crowns (SCs) compared with those of tooth-supported SCs. MATERIALS AND METHODS: Cochrane, Medline (PubMed), and EMBASE database search was performed by three reviewers on reports with patient-reported esthetic outcomes of tooth- and implant-supported SCs. Clinical studies with at least 12 months of mean follow-up period and a minimum of 10 patients, and English, French, or German reports were included. To compare the subgroups, for aggregate-level data, random-effects meta-regression was used. RESULTS: Two thousand fifteen titles were identified (initial search) and screened independently concluding 53 full-text articles to include in data extraction. Twenty-two studies with 29 study cohorts were included. Patients were satisfied with the esthetics of implant- and tooth- supported crowns Mean visual analogue scale (VAS) value from the PROMs data of 1270 implant-supported SCs evaluated by 1051 patients was 89.6% (80.0%-94.1%). The mean VAS value of patients (n = 201), who evaluated the esthetic outcome of 486 tooth-supported SCs was 94.4% (92.3%-96.0%). VAS scores of patients regarding their perception of esthetics did not show any difference among different crown materials or type of implant used. The patients' perception of esthetics focusing on SC had a tendency to be higher when the crowns were supported by teeth, however, no statistical difference was found when compared with implant-supported crowns (p = 0.067). CONCLUSIONS: Patient perception of esthetics in SCs was not affected by the type of support, crown material, implant, and presence of provisional crown for both implant- and tooth-supported SCs. CLINICAL SIGNIFICANCE: Despite that patient's expectations are increasing overall Patients are satisfied with with esthetic outcome of implant- and tooth-supported crowns.

Effect of cross-polarization filters on the trueness of colors obtained with a single-lens reflex camera, macro lens, and a ring flash.

OBJECTIVE: To investigate the effect of cross-polarization filters on the colors of shade tabs obtained with a digital single-lens reflex (DSLR) camera, macrolens, and a ring flash. MATERIALS AND METHODS: Digital images of four shade tables (1M1, 3L2.5, 3R2.5, and 5M3) from the VITA Toothguide 3D-Master shade guide were taken using a DSLR camera, 100 mm macrolens, and ring flash with two different cross-polarizing filters (Polar_eyes and Filtropolar), and without (Nonpolarizer; n = 7). The CIE L*a*b* color coordinates of digital images were calculated and remeasured with a spectroradiometer (SR). The color differences (ΔE00 ) between the SR and digital images were calculated and analyzed with the two-way analysis of variance (ANOVA) and Tukey HSD test (α = 0.05). RESULTS: ΔE00 values of all test groups were higher than the clinically acceptable threshold (∆E00 > 1.80). While the ∆E00 values of Filtropolar (6.19 ± 0.44) and Polar_eyes (7.82 ± 0.23) groups were significantly higher than the Nonpolarizer (4.69 ± 0.32) for the 1M1 shade tab, ∆E00 value of Polar_eyes (6.23 ± 0.34) was significantly lower than Nonpolarizer (10.71 ± 0.48) group for 5M3 shade tab (p < 0.05). CONCLUSION: The color-matching results of tested digital photography techniques with and without cross-polarization were unacceptable, compared to a spectroradiometer. While digital photography with Polar_eyes cross-polarizing filter has closer results to the reference device for the low-in-value shade table (5M3), for the high-in-value shade table (1M1), improved results were obtained without a cross-polarizing filter. CLINICAL SIGNIFICANCE: The cross-polarization filters are increasingly used in dentistry for tooth color communication with digital photography techniques. However, the digital photography techniques with-without cross-polarization filterers should be improved to obtain clinically acceptable color-matching results.

Effect of industrial scanner and framework material interaction on the marginal gaps of CAD-CAM complete arch implant frameworks.

STATEMENT OF PROBLEM: Structured-light and computed tomography industrial scanners have been used as reference scanners to measure marginal gaps between implants and superstructures. However, the effect of framework material on the scanners' ability to detect gaps and on precision has not yet been evaluated. PURPOSE: The purpose of this in vitro study was to investigate the interaction between the industrial scanner and framework material on measured marginal gaps of implant-supported fixed complete arch frameworks made from titanium and polymethylmethacrylate and on the precision of scans. MATERIAL AND METHODS: A completely edentulous maxillary model with 4 implants and multiunit abutments at the first molar and canine sites was digitized by using a laboratory scanner. Implant-supported frameworks were milled from titanium and polymethylmethacrylate (n=5). Each framework was secured on the left molar site abutment. The marginal gaps between the frameworks and abutment sites without a screw were measured by using an industrial structured-light scanner and an industrial computed tomography scanner. The effect of the scanner, the framework material, and their interaction on measured gaps was analyzed by applying linear regressions and weighted least square methods. The F-statistics was used with Bonferroni corrections for precision analysis (α=.05). RESULTS: No significant effect of scanner, material, or their interaction was found on the marginal gaps at the canine sites. The titanium framework gaps detected by using the computed tomography scanner were greater than those detected by using the structured-light scanner at the right molar site (estimated difference in means=0.054 mm; P=.003) and overall (estimated difference in means=0.023 mm; P=.033). The structured-light scanner's precision was higher than that of the computed tomography scanner when titanium frameworks were scanned (P=.001). The computed tomography scanner's precision was higher when scanning polymethylmethacrylate frameworks than when scanning titanium frameworks (P=.03). CONCLUSIONS: Framework material and industrial scanner interaction affected the measured gaps. The computed tomography scanner detected greater marginal gaps with low precision when scanning titanium frameworks than the structured-light scanner. The sample size, the use of only 2 types of materials, and a laboratory scanner to obtain the computer-aided design file should be considered when interpreting the results.

Prosthetic complications with mandibular bar-retained implant overdentures having distal attachments and metal frameworks: A 2- to 12-year retrospective analysis.

STATEMENT OF PROBLEM: Long-term reports on 2-implant-retained overdentures having metal frameworks and bars containing distal attachments are scarce. PURPOSE: The purpose of this retrospective study was to evaluate prosthetic complications with 2-implant-retained mandibular overdentures with metal frameworks having either screw- or cement-retained cantilevered bars with distal attachments. MATERIAL AND METHODS: Seventy-three edentulous study participants who had been treated with mandibular overdentures with 2 implants were included. The parameters assessed were acrylic resin fractures (base fracture, fracture at midline), debonding of teeth, opposing prosthesis fracture, need for relining or rebasing, abutment and bar screw loosening and fracture, ball or bar attachment or clip wear, fracture or detachment, bar fracture, and implant loss. Statistical analysis was performed by using the Mann-Whitney U test as the data were not normally distributed. The categorical variables between the groups were analyzed by using the Fisher exact test (α=.05). RESULTS: Twenty-seven prostheses had a cement-retained bar, and 46 bars were screw-retained. Of 73 overdentures, 68 were metal-reinforced. The mean observation time was 5.9 years with a range between 2 and 12 years. The most common complication was wear of the Rhein 83 polymer attachment followed by bar screw loosening. The cumulative survival rate for overdentures was 91.9% at 6.8 years. The service life of cement-retained prostheses was significantly longer (P<.05). Bar, resin base, and mid-line fractures were only seen with cement-retained prostheses. The number of times an attachment change was required did not differ between cement- and screw-retained bars. Of 191 implants, 3 were lost, and the cumulative survival rate was 93.5% at 7.5 years. No significant difference was found between retention types in terms of implant loss (P>.05). CONCLUSIONS: Based on the participant population observed, the survival rates of 2-implant-retained mandibular overdentures and their implants in the medium term were high. Wear of the polymer attachment was commonly seen. Overdentures with cement-retained bars had bar or acrylic resin fractures. Mandibular 2-implant-retained overdentures with a screw-retained bar containing bilateral distal attachments had fewer prosthetic complications and high implant survival in the medium term.

Effect of surface treatments on wear and surface properties of different CAD-CAM materials and their enamel antagonists.

STATEMENT OF PROBLEM: Which surface treatment provides optimal surface roughness, microhardness, and wear behavior for computer-aided design and computer-aided manufacturing (CAD-CAM) materials and their enamel antagonists is unclear. PURPOSE: The purpose of this in vitro study was to evaluate the effect of surface treatment on the surface roughness, microhardness, and 2-body wear of different CAD-CAM materials and their enamel antagonists. MATERIAL AND METHODS: Monolithic zirconia, polymer-infiltrated ceramic network, lithium disilicate, leucite-reinforced ceramic, zirconia-reinforced lithium silicate, and feldspathic ceramic specimens were sliced into 2-mm-thick rectangular plates and divided into polished or glazed subgroups (n=6). After surface roughness and microhardness measurements, the specimens were loaded at 49 N for 250 000 cycles and simultaneously thermocycled (5 °C and 55 °C). All specimens were scanned before and after the wear test by using a scanner. The volumetric loss and wear depth of the materials and the volumetric and height loss of the enamel were calculated, and scanning electron microscope images of the specimens were made. Multiple 2-way ANOVAs and Tukey honestly significant difference tests were used to assess the effect of material and surface treatment on surface roughness, microhardness, and wear behavior of materials and enamel (α=.05). RESULTS: Material and surface treatment interactions affected the surface roughness (P<.001), microhardness (P<.001), volumetric loss of materials (P=.044), and height loss of enamel (P<.001). CONCLUSIONS: Polishing resulted in higher surface roughness and microhardness than glazing. Volumetric loss depended on the material, which affected the height loss of the antagonists. Glazing and polishing had similar effects on the volumetric loss of materials and antagonists. No correlation was found between the wear of materials and the antagonists, nor between the surface roughness of materials and the volumetric loss of materials or antagonists.