Scanning electrochemical microscopy of individual catalytic nanoparticles.

Electrochemistry at individual metal nanoparticles (NPs) can provide new insights into their electrocatalytic behavior. Herein, the electrochemical activity of single AuNPs attached to the catalytically inert carbon surface is mapped by using extremely small (≥3 nm radius) polished nanoelectrodes as tips in the scanning electrochemical microscope (SECM). The use of such small probes resulted in the spatial resolution significantly higher than in previously reported electrochemical images. The currents produced by either rapid electron transfer or the electrocatalytic hydrogen evolution reaction at a single 10 or 20 nm NP were measured and quantitatively analyzed. The developed methodology should be useful for studying the effects of nanoparticle size, geometry, and surface attachment on electrocatalytic activity in real-world application environment.

A planar, chip-based, dual-beam refractometer using an integrated organic light-emitting diode (OLED) light source and organic photovoltaic (OPV) detectors.

We present a simple chip-based refractometer with a central organic light-emitting diode (OLED) light source and two opposed organic photovoltaic (OPV) detectors on an internal reflection element (IRE) substrate, creating a true dual-beam sensor platform. For first-generation platforms, we demonstrate the use of a single heterojunction OLED based on electroluminescence from an Alq(3)/TPD heterojunction (tris-(8-hydroxyquinoline)aluminum/N,N'-bis(3-methylphenyl)-N,N'-diphenylbenzidine) and light detection with planar heterojunction pentacene/C(60) OPVs. The sensor utilizes the considerable fraction of emitted light from conventional thin-film OLEDs that is coupled into guided modes in the IRE, instead of into the forward (display) direction. A ray-optics description is used to describe light throughput and efficiency-limiting factors for light coupling from the OLED into the substrate modes, light traversing through the IRE substrate, and light coupling into the OPV detectors. The arrangement of the OLED at the center of the chip provides for two sensing regions: a "sample" channel and a "reference" channel, with detection of light by independent OPV detectors. This configuration allows for normalization of the sensor response against fluctuations in OLED light output, stability, and local fluctuations (temperature) that might influence sensor response. The dual-beam configuration permits significantly enhanced sensitivity to refractive index changes, relative to single-beam protocols, and is easily integrated into a field-portable instrumentation package. Changes in refractive index (DeltaRI) between 10(-2) and 10(-3) RI units could be detected for single beam operation, with sensitivity increased to DeltaRI approximately 10(-4) RI units when the dual-beam configuration is employed.

Selective Interlayers and Contacts in Organic Photovoltaic Cells.

Organic photovoltaic cells (OPVs) are promising solar electric energy conversion systems with impressive recent optimization of active layers. OPV optimization must now be accompanied by the development of new charge-selective contacts and interlayers. This Perspective considers the role of interface science in energy harvesting using OPVs, looking back at early photoelectrochemical (photogalvanic) energy conversion platforms, which suffered from a lack of charge carrier selectivity. We then examine recent platforms and the fundamental aspects of selective harvesting of holes and electrons at opposite contacts. For blended heterojunction OPVs, contact/interlayer design is especially critical because charge harvesting competes with recombination at these same contacts. New interlayer materials can modify contacts to both control work function and introduce selectivity and chemical compatibility with nonpolar active layers and add thermodynamic and kinetic selectivity to charge harvesting. We briefly discuss the surface and interface science required for the development of new interlayer materials and take a look ahead at the challenges yet to be faced in their optimization.

Photoemission spectroscopy of tethered CdSe nanocrystals: shifts in ionization potential and local vacuum level as a function of nanocrystal capping ligand.

We report the characterization of the frontier orbital energies and interface dipole effects for bare and ligand-capped 3.6 and 6.0 nm diameter CdSe nanocrystals (NC) tethered to smooth gold substrates, using He(I) and He(II) UV photoemission spectroscopy. Changes in the ionization potential (IP) of the NCs and local effective work function of the films were explored as a function of the dipolar nature of the NC capping ligands. The addition of thiol-capping ligands 1-hexanethiol, 1-benzenethiol, and 4-fluorothiophenol to both sizes of NCs produces negligible shifts in energy offset between the high kinetic energy edge of the CdSe NCs and the gold substrate Fermi energy. However, the local vacuum level and IP of the nanocrystal layer are altered by as much as 0.3 eV. We demonstrate the importance of determining both the local vacuum level and the high kinetic energy edge of a tethered NC sample. These studies demonstrate a method that can be used in the future to characterize the frontier orbital energy offsets for modified or unmodified nanocrystalline films, in which the NCs are incorporated into host materials, for applications ranging from photovoltaics to light-emitting diodes.