RESUMEN
We introduce a method to measure the dynamic surface deformation of an active stressed lap for fabricating a 4 mf/1.5 mirror. Lap surface accuracy working in some typical deformation velocities is put forward. Experimental results indicate that dynamic lap surface accuracy is worse than that of a static surface, and dynamic surface accuracy gets worse if deformation velocity increases, while the difference of lap surface error RMS is less than 1 µm. An optimization of the processing strategy is feasible through changing the deformation velocity of the active stressed lap depending on the processing schedule. After optimizing the grinding and polishing strategy, efficiency is expected to have a significant increase.
RESUMEN
The surface shape accuracy of the active stressed lap impacts the performance of grinding and polishing in the fabrication of large mirrors. We introduce a model of active stressed lap for the fabrication of a 4 m f/1.5 mirror based on finite element analysis (FEA), and the lap surface accuracy achieves RMS<1.8 µm in the FEA method. Using the lap surface measurement system, experimental verification is put forward, and the RMS of the measured lap surface is within 2 µm in practice. A general improvement in lap surface accuracy using the Zernike polynomial is shown. After compensating the calculation errors, the lap surface accuracy is improved by 8%-23%, and achieves RMS<1.5 µm, which is appropriate for practical grinding and polishing.
RESUMEN
Tuberculosis (TB), a leading cause of mortality globally, is a chronic infectious disease caused by Mycobacterium tuberculosis that primarily infiltrates the lung. The mature crRNAs in M. tuberculosis transcribed from the Clustered Regularly Interspaced Short Palindromic Repeats (CRISPR) locus exhibit an atypical structure featured with 5' and 3' repeat tags at both ends of the intact crRNA, in contrast to typical Type-III-A crRNAs that possess 5' repeat tags and partial crRNA sequences. However, this structural peculiarity particularly concerning the specific binding characteristics of the 3' repeat end within the mature crRNA within the Csm complex, has not been comprehensively elucidated. Here, our Mycobacteria CRISPR-Csm complexes structure represents the largest Csm complex reported to date. It incorporates an atypical Type-III-A CRISPR RNA (crRNA) (46 nt) with 5' 8-nt and 3' 4-nt repeat sequences in the stoichiometry of Mycobacteria Csm1125364151. The PAM-independent single-stranded RNAs (ssRNAs) are the most suitable substrate for the Csm complex. The 3'-repeat end trimming of mature crRNA was not necessary for its cleavage activity in Type-III-A Csm complex. Our work broadens our understanding of the Type-III-A Csm complex and identifies another mature crRNA processing mechanism in the Type-III-A CRISPR-Cas system based on structural biology.
Asunto(s)
Mycobacterium tuberculosis , Tuberculosis , Humanos , ARN Guía de Sistemas CRISPR-Cas , ARN Bacteriano/genética , Sistemas CRISPR-Cas/genética , Mycobacterium tuberculosis/genética , Mycobacterium tuberculosis/metabolismo , Tuberculosis/genéticaRESUMEN
The recently discovered type III-E CRISPR-Cas effector Cas7-11 shows promise when used as an RNA manipulation tool, but its structure and the mechanisms underlying its function remain unclear. Here we present four cryo-EM structures of Desulfonema ishimotonii Cas7-11-crRNA complex in pre-target and target RNA-bound states, and the cryo-EM structure of DiCas7-11-crRNA bound to its accessory protein DiCsx29. These data reveal structural elements for pre-crRNA processing, target RNA cleavage and regulation. Moreover, a 3' seed region of crRNA is involved in regulating RNA cleavage activity of DiCas7-11-crRNA-Csx29. Our analysis also shows that both the minimal mismatch of 4 nt to the 5' handle of crRNA and the minimal matching of the first 12 nt of the spacer by the target RNA are essential for triggering the protease activity of DiCas7-11-crRNA-Csx29 towards DiCsx30. Taken together, we propose that target RNA recognition and cleavage regulate and fine-tune the protease activity of DiCas7-11-crRNA-Csx29, thus preventing auto-immune responses.
Asunto(s)
Sistemas CRISPR-Cas , ARN , Microscopía por Crioelectrón , ARN/genética , División del ARN , ARN Guía de Sistemas CRISPR-Cas , Péptido Hidrolasas/genéticaRESUMEN
Ion pumping microbial rhodopsins are photochemically active membrane proteins, converting light energy into ion-motive-force for ATP synthesis. Nonlabens dokdonensis rhodopsin 2 (NdR2), was recently identified as a light-driven Na+ pump. However, few functional studies on NdR2 have been conducted to elucidate its mechanism of ion transport. By reconstituting NdR2 into liposomes, we proved that NdR2 functions as a light-driven Na+/H+ pump. As Na+ concentration increased, the dominant H+ pump activity switched to the Na+ pump activity at neutral pH. The inversion of pH change by the addition of CCCP at low Na+ further suggested that the transport of Na+ and H+ should coexist in NdR2. By increasing H+ concentration, the affinity for Na+ lowered, which was indicated by an increase in KM from ~31mM at pH ~7.5, to ~74mM at pH ~6.5. These results demonstrated that Na+ transport competed with H+ transport in NdR2, which was confirmed by the dominant H+ pump activity at pH ~5.7. Kinetic experiments using pyranine uncovered a transient H+ uptake, followed by an H+ release at the millisecond time scale in both Na+ and K+ solutions. Therefore, these NdR2 results may provide functional and kinetic insights into the ion transport mechanism in light-driven Na+ pumps.