Effect of Carboxyl Group Position on Assembly Behavior and Structure of Hydrocarbon Oil-Carboxylic Acid Compound Collector on Low-Rank Coal Surface: Sum-Frequency Vibration Spectroscopy and Coarse-Grained Molecular Dynamics Simulation Study.

In this work, the assembly behavior and structure of a compound collector with different carboxyl group positions at the low-rank coal (LRC)-water interface were investigated through coarse-grained molecular dynamics simulation (CGMD) combined with sum-frequency vibration spectroscopy (SFG). The choice of compound collector was dodecane +decanoic acid (D-DA) and dodecane +2-butyl octanoic acid (D-BA). CGMD results showed that the carboxyl group at the carbon chain's middle can better control the assembly process between carboxylic acid and D molecules. SFG research found that the carboxyl group at the carbon chain's termination had a greater impact on the displacement of the methyl/methylene symmetric stretching vibration peak, while the carboxyl group at the carbon chain's middle had a greater impact on the displacement of the methyl/methylene asymmetric stretching vibration peak. The spatial angle calculation results revealed that the methyl group's orientation angle in the D-BA molecule was smaller and the carboxyl group's orientation angle in the BA molecule was bigger, indicating that D-BA spread more flatly on the LRC surface than D-DA. This meant that the assembled structure had a larger effective adsorption area on the LRC surface. The flotation studies also verified that the assembly behavior and structure of D-BA with the carboxyl group at the carbon chain's middle at the LRC-water interface were more conducive to the improvement of flotation efficiency. The study of interface assembly behavior and structure by CGMD combined with SFG is crucial for the creation of effective compound collectors.

The Key Effect of Carboxyl Group and CuN2 O2 Coordinate Structure for Cu, N Co-Doped Carbon Dots with Peroxidase-Like Property.

Carbon dots (CDs) with good water solubility and biocompatibility have become a research hotspot in the nano-enzyme and biomedical field. However, the problems of low catalytic activity and ambiguous catalytic site of CDs as nanozymes still need to be addressed. In this work, CDs loaded with Cu single atoms are obtained through pyrolysis, and the coordination structure and surface functional groups are regulated by adjusting the pyrolysis temperature. CDs obtained at 300 °C (named Cu-CDs-300) have the most carboxyl content and Cu is coordinated in the form of CuN2 O2 , which can better decompose H2 O2 to produce free radical and is beneficial to catalyze the oxidation of 3,3',5,5'-tetramethylbenzidine (TMB). The vmax is 6.56*10-7  m s-1 , 6.56 times higher than that of horseradish peroxidase (HRP). Moreover, Cu-CDs-300 can effectively lead to CT26 apoptosis by generating much free radicals. This work demonstrates the synergistic effect of oxygen-containing functional groups and metal coordination structures on peroxide-like activity of CDs and provides new ideas for the design of clear active structure and high efficiency peroxide-like single atom CDs catalyst.

Novel Carboxylation Method for Polyetheretherketone (PEEK) Surface Modification Using Friedel-Crafts Acylation.

Recently, polyetheretherketone (PEEK) has shown promising dental applications. Surface treatment is essential for dental applications owing to its poor surface energy and wettability; however, no consensus on an effective treatment method has been achieved. In this study, we attempted to carboxylate PEEK sample surfaces via Friedel-Crafts acylation using succinic anhydride and AlBr3. The possibility of further chemical modifications using carboxyl groups was examined. The samples were subjected to dehydration-condensation reactions with 1H,1H-pentadecafluorooctylamine and N,N'-dicyclohexylcarbodiimide. Furthermore, the sample's surface properties at each reaction stage were evaluated. An absorption band in the 3300-3500 cm-1 wavenumber region was observed. Additionally, peak suggestive of COOH was observed in the sample spectra. Secondary modification diminished the absorption band in 3300-3500 cm-1 and a clear F1s signal was observed. Thus, Friedel-Crafts acylation with succinic anhydride produced carboxyl groups on the PEEK sample surfaces. Further chemical modification of the carboxyl groups by dehydration-condensation reactions is also possible. Thus, a series of reactions can be employed to impart desired chemical structures to PEEK surfaces.

A Carboxyl Group-Functionalized Ionic Liquid Hybrid Adsorbent for Solid-Phase Extraction and Determination of Trace Diclofenac Sodium in Milk Samples.

A simple and efficient sample pretreatment technology is very important for the accurate determination of trace drug residues in foods to ensure food safety. Herein, we report a new carboxyl group-functionalized ionic liquid hybrid solid- phase adsorbent (PS-IL-COOH) for the highly efficient extraction and quantitative determination of diclofenac sodium (DS) residue in milk samples. It was found that the adsorption efficiency of PS-IL-COOH for the ppb level of DS was greater than 93.0%, the adsorption capacity was 934.1 mg/g, and the enrichment factor was 620.0, which surpass most of the previously reported values for DS adsorbents. The high concentration of salts did not interfere with the adsorption of DS. Importantly, the recovery of DS was above 90% after 16 adsorption--regeneration cycles. The synergistic effect of the multiple interactions was found to be the main factor for the high efficiency of DS adsorption. The proposed method was applied to the extraction and detection of DS in milk samples, with the relative recovery ranging from 88.2 to 103.0%.

Facile Synthesis of Quinolinecarboxylic Acid-Linked Covalent Organic Framework via One-Pot Reaction for Highly Efficient Removal of Water-Soluble Pollutants.

To efficiently eliminate highly polar organic pollutants from water has always been a difficult issue, especially in the case of ultralow concentrations. Herein, we present the facile synthesis of quinolinecarboxylic acid-linked COF (QCA-COF) via the Doebner multicomponent reaction, possessing multifunction, high specific surface area, robust physicochemical stability, and excellent crystallinity. The marked feature lies in the quinolinyl and carboxyl functions incorporated simultaneously to QCA-COF in one step. The major cis-orientation of carboxyl arms in QCA-COF was speculated by powder X-ray diffraction and total energy analysis. QCA-COF demonstrates excellent adsorption capacity for water-soluble organic pollutants such as rhodamine B (255.7 mg/g), methylene blue (306.1 mg/g), gentamycin (338.1 mg/g), and 2,4-dichlorophenoxyacetic acid (294.1 mg/g) in water. The kinetic adsorptions fit the pseudo-second order model and their adsorption isotherms are Langmuir model. Remarkably, QCA-COF can capture the above four water-soluble organic pollutants from real water samples at ppb level with higher than 95% removal efficiencies and excellent recycling performance.

Carboxyl group-modified myoglobin shows membrane-permeabilizing activity.

In this study, we investigated whether modification of the carboxyl group with semicarbazide-enabled myoglobin (Mb) exhibits membrane-perturbing activity in physiological solutions. Mass spectrometry analysis showed that semicarbazide molecules were coupled to 19 of the 22 carboxyl groups in semicarbazide-modified Mb (SEM-Mb). Measurements of the absorption and circular dichroism spectra indicated that SEM-Mb lost its heme group and reduced the content of the α-helix structure in Mb. The microenvironment surrounding Trp residues in Mb changes after blocking negatively charged residues, as shown by fluorescence quenching studies. The results of the trifluoroethanol-induced structural transition indicated that SEM-Mb had higher structural flexibility than that of Mb. SEM-Mb, but not Mb, induced the permeability of bilayer membranes. Both proteins showed similar lipid-binding affinities. The conformation of SEM-Mb and Mb changed upon binding to lipid vesicles or a membrane-mimicking environment composed of SDS micelles, suggesting that membrane interaction modes differ. Unlike lipid-bound Mb, Trp residues in lipid-bound SEM-Mb are located at the protein-lipid interface. Altogether, our data indicate that modifying negatively charged groups relieves the structural constraints in Mb, consequently switching Mb structure to an active conformation that exhibits membrane-permeabilizing activity.

Functional and structural properties of cardiotoxin isomers produced by blocking negatively charged groups.

In this study, we investigated the functional roles of Asp40, Asp57, and C-terminal Asn60 in Naja atra cardiotoxin 3 (CTX3) structure and function by modifying these three carboxyl groups with semicarbazide. The conjugation of the carboxyl groups with semicarbazide produced two conformational isomers whose gross and fine structures were different from those of CTX3. The blocking of the carboxyl groups increased the structural flexibility of CTX3 in response to trifluoroethanol-induced effect. Despite presenting modest to no effect on decreasing the induction of permeability in zwitterionic phospholipid vesicles, the carboxyl group-modified CTX3 showed a marked reduction in its permeabilizing effect on anionic phospholipid vesicles in comparison to that of the native protein. Compared with native CTX3, carboxyl group-modified CTX3 exhibited lower activity in inducing membrane leakage in U937 cells. The CD spectra of lipid-bound toxins and the color transition of polydiacetylene/lipid assay showed that the membrane interaction mode of CTX3 was distinctly changed by the modification in the carboxyl groups. Given that the selective modification of Asp40 does not cause the conformational isomerization of CTX3, our data indicate that the carboxyl groups in Asp57 and Asn60 are essential in maintaining the structural topology of CTX3. Furthermore, modification of carboxyl groups changes the interdependence between the infrastructure and the global conformation of CTX3 in modulating membrane permeabilizing activity.

Interaction between Organic Compounds and Catalyst Steers the Oxidation Pathway and Mechanism in the Iron Oxide-Based Heterogeneous Fenton System.

In the past decades, extensive efforts have been devoted to the mechanistic understanding of various heterogeneous Fenton reactions. Nevertheless, controversy still remains on the oxidation mechanism/pathway toward different organic compounds in the classical iron oxide-based Fenton reaction, largely because the role of the interaction between the organic compounds and the catalyst has been scarcely considered. Here, we revisited the classic heterogeneous ferrihydrite (Fhy)/H2O2 system toward different organic compounds on the basis of a series of degradation experiments, alcohol quenching experiments, theoretical modeling, and intermediate analysis. The Fhy/H2O2 system exhibited highly selective oxidation toward the group of compounds that bear carboxyl groups, which tend to complex with the surface ≡Fe(III) sites of the Fhy catalyst. Such interaction results in a nonradical inner sphere electron transfer process, which seizes one electron from the target compound and features negligible inhibition by the radical quencher. In contrast, for the oxidation of organic compounds that could not complex with the catalyst, the traditional HO· process makes the main contribution, which proceeds via hydroxyl addition reaction and could be readily suppressed by the radical quencher. This study implies that the interaction between the organic compounds and the catalyst plays a decisive role in the oxidation pathway and mechanism of the target compounds and provides a holistic understanding on the iron oxide-based heterogeneous Fenton system.

H2+CO2 Synergistic Plasma Positioning Carboxyl Defects in g-C3N4 with Engineered Electronic Structure and Active Sites for Efficient Photocatalytic H2 Evolution.

Defective functional-group-endowed polymer semiconductors, which have unique photoelectric properties and rapid carrier separation properties, are an emerging type of high-performance photocatalyst for various energy and environmental applications. However, traditional oxidation etching chemical methods struggle to introduce defects or produce special functional group structures gently and controllably, which limits the implementation and application of the defective functional group modification strategy. Here, with the surface carboxyl modification of graphitic carbon nitride (g-C3N4) photocatalyst as an example, we show for the first time the feasibility and precise modification potential of the non-thermal plasma method. In this method, the microwave plasma technique is employed to generate highly active plasma in a combined H2+CO2 gas environment. The plasma treatment allows for scalable production of high-quality defective carboxyl group-endowed g-C3N4 nanosheets with mesopores. The rapid H2+CO2 plasma immersion treatment can precisely tune the electronic and band structures of g-C3N4 nanosheets within 10 min. This conjoint approach also promotes charge-carrier separation and accelerates the photocatalyst-catalyzed H2 evolution rate from 1.68 mmol h-1g-1 (raw g-C3N4) to 8.53 mmol h-1g-1 (H2+CO2-pCN) under Xenon lamp irradiation. The apparent quantum yield (AQY) of the H2+CO2-pCN with the presence of 5 wt.% Pt cocatalyst is 4.14% at 450 nm. Combined with density functional theory calculations, we illustrate that the synergistic N vacancy generation and carboxyl species grafting modifies raw g-C3N4 materials by introducing ideal defective carboxyl groups into the framework of heptazine ring g-C3N4, leading to significantly optimized electronic structure and active sites for efficient photocatalytic H2 evolution. The 5.08-times enhancement in the photocatalytic H2 evolution over the as-developed catalysts reveal the potential and maneuverability of the non-thermal plasma method in positioning carboxyl defects and mesoporous morphology. This work presents new understanding about the defect engineering mechanism in g-C3N4 semiconductors, and thus paves the way for rational design of effective polymeric photocatalysts through advanced defective functional group engineering techniques evolving CO2 as the industrial carrier gas.

Impacts of surface chemistry of functional carbon nanodots on the plant growth.

Functional carbon nanodots (FCNs) with multiple chemical groups have great impact on the growth regulation of plants. To understand the role of the chemical groups, FCNs were reduced from the raw material by pyrolysis method and hydrolysis method. The chemical structure of these materials were characterized by using TGA, TEM, FT-IR, XPS, Raman and elementary analysis. The raw and reduced FCNs were used as plants growth regulators in culture medium of Arabidopsis thaliana. Our results indicate there is a strong correlation between the physiological responses of plants and the surface chemistries (especially carboxyl group and ester group) of the nanomaterials. The quantum-sized FCNs with multiple carboxyl groups and ester groups show better aqueous dispersity and can induce various positive physiological responses in Arabidopsis thaliana seedlings compared with the FCNs decorated without carboxyl and ester as well as aggregated FCNs. The raw FCNs present higher promotion capacity in plants biomass and roots length, and the quantum-sized FCNs are easier to be absorbed by plants and generate more positive effects on plants.

Carbon nanotubes in electrochemical, colorimetric, and fluorimetric immunosensors and immunoassays: a review.

This review (with 126 references) summarizes the progress that has been made in the use of carbon nanotubes (CNTs) in immunoassays and immunosensors. Following an introduction into the field, a first large section covers functional group-modified CNTs as carriers for antibodies (with subsections on CNTs modified with amino, carboxy and by various other materials). The next section treats CNTs coupled with inorganic or organic materials as active components (with the use of nanoparticles such as Fe3O4, ZnO, gold) or with indium tin oxide (ITO), NiCoBP, ionic liquids, TiO2 nanosheets, metal clusters; chitosan, polystyrene, polydopamine, graphene, or enzymes. Another section discusses the synergistic effects of CNTs with metals, metal ions, and organic/inorganic materials. Several Tables are presented that give an overview on the wealth of methods and materials. A concluding section summarizes the current status, addresses current challenges, and gives an outlook on potential future trends. Graphical abstract Schematic presentation of the roles of carbon nanotubes (CNTs) in immunosensors and immunoassays. (I) Functional group-modified CNTs as carriers for antibody; (II) CNTs coupled with metal or organic materials as active component; and (III) Synergistic effects of CNTs with other materials to improve the parameters of immunosensors.

Inter- vs. Intramolecular Hydrogen Bond Patterns and Proton Dynamics in Nitrophthalic Acid Associates.

Noncovalent interactions are among the main tools of molecular engineering. Rational molecular design requires knowledge about a result of interplay between given structural moieties within a given phase state. We herein report a study of intra- and intermolecular interactions of 3-nitrophthalic and 4-nitrophthalic acids in the gas, liquid, and solid phases. A combination of the Infrared, Raman, Nuclear Magnetic Resonance, and Incoherent Inelastic Neutron Scattering spectroscopies and the Car-Parrinello Molecular Dynamics and Density Functional Theory calculations was used. This integrated approach made it possible to assess the balance of repulsive and attractive intramolecular interactions between adjacent carboxyl groups as well as to study the dependence of this balance on steric confinement and the effect of this balance on intermolecular interactions of the carboxyl groups.

Membrane-damaging activities of mannosylated ovalbumin are involved in its antibacterial action.

Mannosylated ovalbumin (Man-OVA) prepared by modification of carboxyl groups with p-aminophenyl α-d-mannopyranoside shows an increase of net positive charge, which may enhance its binding to bacterial membrane. Thus, we aimed to investigate whether Man-OVA exerts antibacterial activity on Escherichia coli and Staphylococcus aureus via membrane-perturbing effect. Man-OVA inhibited the growth of E. coli and S. aureus, whereas ovalbumin (OVA) did not show any antibacterial activity. Moreover, Man-OVA induced an increase in the membrane permeability of E. coli and S. aureus, which was positively correlated to its bactericidal action. Morphological examination using scanning electron microscopy revealed that Man-OVA disrupted the bacterial membrane integrity. Destabilization of the lipopolysaccharide (LPS) layer and inhibition of lipoteichoic acid (LTA) biosynthesis in the cell wall increased the bactericidal effect of Man-OVA. In contrast to OVA, Man-OVA also induced leakage of bacterial membrane-mimicking liposomes. Color transformation of phospholipid/polydiacetylene membrane assay revealed that the membrane-interaction mode of Man-OVA was distinct from that of OVA. LPS and LTA suppressed the membrane-damaging activity of Man-OVA, whereas an increase in the Man-OVA concentration attenuated the inhibitory action of LPS and LTA. Taken together, our data indicate that the bactericidal activity of Man-OVA depends strongly on its ability to induce membrane permeability.

Synthesis and bioactivities of Phenazine-1-carboxylic acid derivatives based on the modification of PCA carboxyl group.

Phenazine-1-carboxylic acid (PCA) as a natural product widely exists in microbial metabolites of Pseudomonads and Streptomycetes and has been registered for the fungicide against rice sheath blight in China. To find higher fungicidal activities compounds and study the effects on fungicidal activities after changing the carboxyl group of PCA, we synthesized a series of PCA derivatives by modifying the carboxyl group of PCA and their structures were confirmed by 1H NMR and HRMS. Most compounds exhibited significant fungicidal activities in vitro. In particular, compound 6 exhibited inhibition effect against Rhizoctonia solani with EC50 values of 4.35mg/L and compound 3b exhibited effect against Fusarium graminearum with EC50 values of 8.30mg/L, compared to the positive control PCA with its EC50 values of 7.88mg/L (Rhizoctonia solani) and 127.28mg/L (Fusarium graminearum), respectively. The results indicated that the carboxyl group of PCA could be modified to be amide group, acylhydrazine group, ester group, methyl, hydroxymethyl, chloromethyl and ether group etc. And appropriate modifications on carboxyl group of PCA were useful to extend the fungicidal scope.

Chemically modified surface functional groups of Alcaligenes sp. S-XJ-1 to enhance its demulsifying capability.

Cell-surface functional groups (amino, carboxyl, hydroxyl, as well as phosphate) were chemically modified in various ways to enhance the demulsification capability of the demulsifying bacteria Alcaligenes sp. S-XJ-1. Results demonstrated that the demulsifying activity was significantly inhibited by amino enrichment with cetyl trimethyl ammonium bromide, amino methylation, hydroxyl acetylation, and phosphate esterification, but was gradually promoted by carboxyl blocking with increasing the extents of esterification. Compared with the raw biomass, an optimal esterification of carboxyl moieties enhanced the demulsification ratio by 26.5% and shortened the emulsion half-life from 24 to 8.8 h. The demulsification boost was found to be dominated by strengthened hydrophobicity (from 53° to 74°) and weakened electronegativity (from -34.6 to -4.3 mV at pH 7.0) of the cell surface, allowing the rapid dispersion and adsorption of cells onto the oil-water interface. The chemical modification of the functional groups on the biomass surface is a promising tool for the creation of a high-performance bacterial demulsifier.

Ovalbumin with Glycated Carboxyl Groups Shows Membrane-Damaging Activity.

The aim of the present study was to investigate whether glycated ovalbumin (OVA) showed novel activity at the lipid-water interface. Mannosylated OVA (Man-OVA) was prepared by modification of the carboxyl groups with p-aminophenyl α-dextro (d)-mannopyranoside. An increase in the number of modified carboxyl groups increased the membrane-damaging activity of Man-OVA on cell membrane-mimicking vesicles, whereas OVA did not induce membrane permeability in the tested phospholipid vesicles. The glycation of carboxyl groups caused a notable change in the gross conformation of OVA. Moreover, owing to their spatial positions, the Trp residues in Man-OVA were more exposed, unlike those in OVA. Fluorescence quenching studies suggested that the Trp residues in Man-OVA were located on the interface binds with the lipid vesicles, and their microenvironment was abundant in positively charged residues. Although OVA and Man-OVA showed a similar binding affinity for lipid vesicles, the lipid-interacting feature of Man-OVA was distinct from that of OVA. Chemical modification studies revealed that Lys and Arg residues, but not Trp residues, played a crucial role in the membrane-damaging activity of Man-OVA. Taken together, our data suggest that glycation of carboxyl groups causes changes in the structural properties and membrane-interacting features of OVA, generating OVA with membrane-perturbing activities at the lipid-water interface.

The role of the glucuronoxylan carboxyl groups in the action of endoxylanases of three glycoside hydrolase families: A study with two substrate mutants.

BACKGROUND: Bacterial appendage-dependent GH30 glucuronoxylan hydrolases recognize the substrate through an ionic interaction of a conserved positively charged arginine with the carboxyl group of 4-O-methyl-d-glucuronic acid. One of the options to verify this interaction is preparation of enzyme mutants. An alternative approach is a chemical modification of the substrate, glucuronoxylan, in which the free carboxyl group in all residues of MeGlcA is eliminated. METHODS: In this work the carboxyl groups of 4-O-methyl-d-glucuronic acid residues of an alkali extracted beechwood xylan were esterified with methanol. A water-soluble fraction of the polysaccharide methyl ester was converted by NaBH4 reduction to the second soluble derivative, 4-O-methylglucoxylan. Specific activities of several endoxylanases (EXs) of GH families 10, 11 and 30 were determined on glucuronoxylan, and its two new uncharged derivatives. RESULTS: Elimination of the free carboxyl group from the polysaccharide did not influence activities of GH10 EXs, but resulted in 50% decrease of specific activity of GH11 EXs, and led to more than 300-fold reduction of specific activity of Erwinia chrysanthemi GH30 xylanase. CONCLUSIONS: These results confirm the crucial role of the interactions between GH30 xylanases and the MeGlcA carboxyl group for efficient cleavage of the polysaccharide. Analysis of the hydrolysis products by TLC and MS confirmed that all three types of xylanases hydrolyzed uncharged glucuronoxylans similarly as the original one. SIGNIFICANCE: The uncharged glucuronoxylan derivatives will be useful to differentiate GH30 xylanases with various degree of selectivity for glucuronoxylan, including fungal enzymes without the conserved arginine.

Cell culture on hydrophilicity-controlled silicon nitride surfaces.

Cell culture on silicon nitride membranes is required for atmospheric scanning electron microscopy, electron beam excitation assisted optical microscopy, and various biological sensors. Cell adhesion to silicon nitride membranes is typically weak, and cell proliferation is limited. We increased the adhesion force and proliferation of cultured HeLa cells by controlling the surface hydrophilicity of silicon nitride membranes. We covalently coupled carboxyl groups on silicon nitride membranes, and measured the contact angles of water droplets on the surfaces to evaluate the hydrophilicity. We cultured HeLa cells on the coated membranes and evaluated stretch of the cell. Cell migration and confluence were observed on the coated silicon nitride films. We also demonstrated preliminary observation result with direct electron beam excitation-assisted optical microscope.

Bovine serum albumin with glycated carboxyl groups shows membrane-perturbing activities.

The aim of the present study aimed to investigate whether glycated bovine serum albumin (BSA) showed novel activities on the lipid-water interface. Mannosylated BSA (Man-BSA) was prepared by modification of the carboxyl groups with p-aminophenyl α-d-mannopyranoside. In contrast to BSA, Man-BSA notably induced membrane permeability of egg yolk phosphatidylcholine (EYPC)/egg yolk sphingomyelin (EYSM)/cholesterol (Chol) and EYPC/EYSM vesicles. Noticeably, Man-BSA induced the fusion of EYPC/EYSM/Chol vesicles, but not of EYPC/EYSM vesicles. Although BSA and Man-BSA showed similar binding affinity for lipid vesicles, the lipid-bound conformation of Man-BSA was distinct from that of BSA. Moreover, Man-BSA adopted distinct structure upon binding with the EYPC/EYSM/Chol and EYPC/EYSM vesicles. Man-BSA could induce the fusion of EYPC/EYSM/Chol vesicles with K562 and MCF-7 cells, while Man-BSA greatly induced the leakage of Chol-depleted K562 and MCF-7 cells. The modified BSA prepared by conjugating carboxyl groups with p-aminophenyl α-d-glucopyranoside also showed membrane-perturbing activities. Collectively, our data indicate that conjugation of carboxyl groups with monosaccharide generates functional BSA with membrane-perturbing activities on the lipid-water interface.

Carboxyl and polyamine groups functionalized polyacrylonitrile fibers for efficient recovery of copper ions from solution.

Heavy metals (e.g., Cu) in wastewater are attractive resources for diverse applications, and adsorption is a promising route to recovery of heavy metals from wastewater. However, high-performance adsorbents with high adsorption capacity, speed, and stability remain challenging. Herein, chelating fibers were prepared by chemically grafting amine and carboxyl groups onto the polyacrylonitrile fiber surface and used in the wastewater's adsorption of Cu2+. The adsorption behavior of Cu2+ on the fibers was systematically investigated, and the post-adsorption fibers were comprehensively characterized to uncover the adsorption mechanism. The results show that chelated fiber has a 136.3 mg/g maximum capacity for Cu2+ adsorption at pH = 5, and the whole adsorption process could reach equilibrium in about 60 min. The adsorption process corresponds to the quasi-secondary kinetic and Langmuir models. The results of adsorption, FTIR, and XPS tests indicate that the synergistic coordination of -COOH and -NH2 plays a leading role in the rapid capture of Cu2+. In addition, introducing hydrophilic groups facilitates the rapid contact and interaction of the fibers with Cu2+ in the solution. After being used five times, the fiber's adsorption capacity remains at over 90% of its original level.