RESUMEN
Flexible materials with ionic conductivity and stretchability are indispensable in emerging fields of flexible electronic devices as sensing and protecting layers. However, designing robust sensing materials with skin-like compliance remains challenging because of the contradiction between softness and strength. Herein, inspired by the modulus-contrast hierarchical structure of biological skin, we fabricated a biomimetic hydrogel with strain-stiffening capability by embedding the stiff array of poly(acrylic acid) (PAAc) in the soft polyacrylamide (PAAm) hydrogel. The stress distribution in both stiff and soft domains can be regulated by changing the arrangement of patterns, thus improving the mechanical properties of the patterned hydrogel. As expected, the resulting patterned hydrogel showed its nonlinear mechanical properties, which afforded a high strength of 1.20 MPa while maintaining a low initial Young's modulus of 31.0 kPa. Moreover, the array of PAAc enables the patterned hydrogel to possess protonic conductivity in the absence of additional ionic salts, thus endowing the patterned hydrogel with the ability to serve as a strain sensor for monitoring human motion.
Asunto(s)
Hidrogeles , Piel , Humanos , Hidrogeles/química , Movimiento (Física) , Módulo de Elasticidad , Iones , Conductividad EléctricaRESUMEN
Rapid advances in wearable electronics and mechno-sensational human-machine interfaces impose great challenges in developing flexible and deformable tactile sensors with high efficiency, ultra-sensitivity, environment-tolerance, and self-sustainability. Herein, a tactile hydrogel sensor (THS) based on micro-pyramid-patterned double-network (DN) ionic organohydrogels to detect subtle pressure changes by measuring the variations of triboelectric output signal without an external power supply is reported. By the first time of pyramidal-patterned hydrogel fabrication method and laminated polydimethylsiloxane (PDMS) encapsulation process, the self-powered THS shows the advantages of remarkable flexibility, good transparency (≈85%), and excellent sensing performance, including extraordinary sensitivity (45.97 mV Pa-1 ), fast response (≈20 ms), very low limit of detection (50 Pa) as well as good stability (36 000 cycles). Moreover, with the LiBr immersion treatment method, the THS possesses excellent long-term hyper anti-freezing and anti-dehydrating properties, broad environmental tolerance (-20 to 60 °C), and instantaneous peak power density of 20 µW cm-2 , providing reliable contact outputs with different materials and detecting very slight human motions. By integrating the signal acquisition/process circuit, the THS with excellent self-power sensing ability is utilized as a switching button to control electric appliances and robotic hands by simulating human finger gestures, offering its great potentials for wearable and multi-functional electronic applications.
Asunto(s)
Hidrogeles , Tacto , Suministros de Energía Eléctrica , Electrónica , Humanos , PresiónRESUMEN
Thermoresponsive hydrogel actuators have attracted tremendous interest due to their promising applications in artificial muscles, soft robotics, and flexible electronics. However, most of these materials are based on polymers with lower critical solution temperature (LCST), while those from upper critical solution temperature (UCST) are rare. Herein, we report a multiple-responsive UCST hydrogel actuator based on the complex of poly(acrylic acid) (PAAc) and poly(acrylamide) (PAAm). By applying a heterogeneous photopolymerization, a bilayer hydrogel was obtained, including a layer of the interpenetrating network (IPN) of PAAm/PAAc and a layer of a single network of PAAm. When cooled down below the UCST, the PAAm/PAAc layer contracted due to the hydrogen bonding of the two polymers while the PAAm layer stays in swelling state, driving the hydrogel to curl. By adjusting the composition of the two layers, the amplitude of actuation behavior could be regulated. By creating patterned IPN domains with photomasks, the hydrogel could deform into complex two-dimensional (2D) and three-dimensional (3D) shapes. An active motion was realized in both water and oil bath, thanks to the internal water exchange between the two layers. Interestingly, the hydrogel actuator is also responsive to urea and salts (Na2SO4, NaCl, NaSCN), due to that the strength of the hydrogen bonds in the IPN changes with the additives. Overall, the current study realized an anisotropic UCST transition by introducing asymmetrically distributed polymer-polymer hydrogen bonds, which would inspire new inventions of intelligent materials.
RESUMEN
Reconstruction of large bone defects is limited by insufficient vascularization and slow bone regeneration. The objective of this work was to investigate the effect of spatial and temporal release of recombinant human bone morphogenetic protein-2 (BMP2) and vascular endothelial growth factor (VEGF) on the extent of osteogenic and vasculogenic differentiation of human mesenchymal stem cells (hMSCs) and endothelial colony-forming cells (ECFCs) encapsulated in a patterned hydrogel. Nanogels (NGs) based on polyethylene glycol (PEG) macromers chain-extended with short lactide (L) and glycolide (G) segments were used for grafting and timed-release of BMP2 and VEGF. NGs with 12kDa PEG molecular weight (MW), 24 LG segment length, and 60/40L/G ratio (P12-II, NG(10)) released the grafted VEGF in 10days. NGs with 8kDa PEG MW, 26 LG segment length, and 60/40L/G ratio (P8-I, NG(21)) released the grafted BMP2 in 21days. hMSCs and NG-BMP2 were encapsulated in a patterned matrix based on acrylate-functionalized lactide-chain-extended star polyethylene glycol (SPELA) hydrogel and microchannel patterns filled with a suspension of hMSCs+ECFCs and NG-VEGF in a crosslinked gelatin methacryloyl (GelMA) hydrogel. Groups included patterned constructs without BMP2/VEGF (None), with directly added BMP2/VEGF, and NG-BMP2/NG-VEGF. Based on the results, timed-release of VEGF in the microchannels in 10days from NG(10) and BMP2 in the matrix in 21days from NG(21) resulted in highest extent of osteogenic and vasculogenic differentiation of the encapsulated hMSCs and ECFCs compared to direct addition of VEGF and BMP2. Further, timed-release of VEGF from NG(10) in hMSC+ECFC encapsulating microchannels and BMP2 from NG(21) in hMSC encapsulating matrix sharply increased bFGF expression in the patterned constructs. The results suggest that mineralization and vascularization are coupled by localized secretion of paracrine signaling factors by the differentiating hMSCs and ECFCs.