Characterization of flavor and taste profile of different radish (Raphanus Sativus L.) varieties by headspace-gas chromatography-ion mobility spectrometry (GC/IMS) and E-nose/tongue.

A comprehensive study of the overall flavor and taste profile of different radishes is lacking. This study systematically compared the volatile profile of six radish varieties using HS-GC-IMS and their correlation with the E-nose analysis. Organic acids and amino acids were quantified, and their association with the E-tongues analysis was explored. A total of 73 volatile compounds were identified, with diallyl sulfide and dimethyl disulfide being the primary sulfides responsible for the unpleasant flavor in radish. Compared to other varieties, cherry radishes boast a significantly higher concentration of allyl isothiocyanate, which likely contributes to their characteristic radish flavor. Moreover, oxalic acid was identified as the most abundant organic acid in radish, accounting for over 97% of its content, followed by malic acid and succinic acid. In conclusion, the distinct flavor and taste characteristics of different radish varieties partially explain their suitability for diverse culinary preferences.

Preparation and Investigation of Sustained-Release Nanocapsules Containing Cumin Essential Oil for Their Bacteriostatic Properties.

Cumin essential oil chitosan nanocapsules (CENPs) were prepared through the ionic gelation method by blending chitosan (CS) with cumin essential oil (CEO) in different proportions (1:0.8, 1:1, 1:2, 1:3, 1:4). Subsequently, these nanocapsules were characterized and evaluated for their antibacterial properties to determine the optimal cumin essential oil encapsulation and antibacterial efficacy. The outcomes demonstrated that the highest encapsulation efficiency of CENPs was 52%, achieved with a 1:3 CS/CEO ratio. At this point, the nanoparticles had the smallest particle size (584.67 nm) and a regular spherical distribution in the emulsion. Moreover, the CENPs could release the encapsulated CEOs slowly, leading to efficient inhibition of E. coli and L. monocytogenes over a relatively extended period (24-36 h) compared to the CS and CEO. This research offers a promising approach for the use of nanocapsules in food preservation.

Using temporal dominance of sensations (TDS), multiple-sip TDS, chemical composition evaluation, and microstructural analysis to assess the impact of repeated reheating cycles on chicken soup.

Reheating chicken soup is a common culinary practice in daily life. To investigate the impact of reheating frequency on the sensory quality of chicken soup, temporal dominance of sensations (TDS) and multi-TDS were used to characterize changes in dominant sensory attributes during consumption. Additionally, E-nose and E-tongue were utilized to analyze differences in aroma and taste profiles. The alterations in sensory properties were further elucidated by analyzing variations in amino acids, volatile compounds. The findings revealed that there was no significant disparity between fresh soup and heating. However, saltiness and umami, as the most prominent dominant characteristics, intensified with increasing reheating cycles. This can be attributed to an elevation in certain amino acids that contribute to umami perception. Conversely, a reduction in some aldehydes weakened the flavor associated with fat and meat components. Moreover, enlarged oil droplets with uneven distribution within heated soup may account for the heightened greasiness sensation.

Exploring the Profile Contributions in Meyerozyma guilliermondii YB4 under Different NaCl Concentrations Using GC-MS Combined with GC-IMS and an Electronic Nose.

Using Meyerozyma guilliermondii YB4, which was isolated and screened from southern Sichuan pickles in the laboratory, as the experimental group, we investigated the changes in growth, total ester content, and volatile flavor substances of M. guilliermondii YB4 under different NaCl concentrations. The growth of M. guilliermondii YB4 was found to be inhibited by NaCl, and the degree of inhibition increased at higher NaCl concentrations. Additionally, the total ester content of the control group (CK) was significantly lower compared to the other groups (p < 0.05). The application of NaCl also resulted in distinct changes in the volatile profile of YB4, as evidenced by E-nose results. Gas chromatography-mass spectrometry (GC-MS) and gas chromatography-ion mobility spectrometry (GC-IMS) were employed to analyze the volatile compounds. A total of 148 and 86 volatiles were detected and identified using GC-MS and GC-IMS, respectively. Differential volatiles among the various NaCl concentrations in YB4 were determined by a variable importance in projection (VIP) analysis in partial least squares-discriminant analysis (PLS-DA). These differentially expressed volatiles were further confirmed by their relative odor activity value (ROAV) and odor description. Ten key contributing volatiles were identified, including ethanol, 1-pentanol, nonanal, octanal, isoamyl acetate, palmitic acid ethyl ester, acrolein, ethyl isobutanoate, prop-1-ene-3,3'-thiobis, and 2-acetylpyrazine. This study provides insights into the specificities and contributions of volatiles in YB4 under different NaCl concentrations. These findings offer valuable information for the development of aroma-producing yeast agents and the subsequent enhancement in the flavor of southern Sichuan pickles.

Effect of fat replacement by flaxseed flour on the quality parameters of pork meatballs.

To improve the edible qualities of meatballs, various percentages of pork fat in meatballs were replaced by brown flaxseed flour (BFF) to decrease the fat contents and further optimize the fatty acid compositions. Five different meatball formulations that used 0%, 5%, 10%, 15%, and 20% of flaxseed flour additions were used in which the corresponding amounts pork fat were replaced. The proximate compositions, water activity, pH levels, colors, textures, cooking losses, fatty acid compositions, sensory properties, flavors, and oxidation stabilities of these meatballs were analyzed. Increasing the BFF addition amounts improved the protein and dietary fiber contents, pH levels, fatty acid profiles and oxidation stabilities, but decreased the fat contents, moisture levels, cooking losses, n6/n3 ratios, hardness, and lightness. The volatile flavors of meatballs with different BFF replacement levels were significantly different. According to the sensory evaluation, the use of 5% BFF increased the odor of meatballs without significantly affecting the other sensory scores. This work demonstrated that BFF may be a healthier alternative as pork fat replacer for preparing meatballs.

Effects of Different Low-Temperature Storage Methods on the Quality and Processing Characteristics of Fresh Beef.

Low-temperature storage has become the most common way for fresh meat storage because of its lower cost and better preservation effect. Traditional low-temperature preservation includes frozen storage and refrigeration storage. The refrigeration storage has a good fresh-keeping effect, but the shelf life is short. Frozen storage has a long shelf life, but it has a great impact on the quality of meat structure and other qualities, and cannot achieve a complete "fresh-keeping" effect. With the development of food processing storage and freezing technology, two new storage methods, ice temperature storage and micro-frozen storage, have attracted more attention. In this paper, the effects of different low-temperature storage methods on the sensory, physicochemical properties, myofibrillar protein oxidation, microstructure, and processing characteristics of fresh beef were studied. The optimal storage methods under different storage requirements were analyzed to reveal the mechanism and efficacy of ice temperature storage and micro-frozen storage technology, as well as the advantages compared with traditional low-temperature refrigeration. It has practical significance for guiding the application of low-temperature storage of fresh meat. Finally, this study concluded that the longest shelf life could be achieved by frozen storage, and the best preservation effect was achieved during the shelf life of ice temperature storage, and the effect of micro-frozen storage on the myofibrillar protein oxidation and microstructure was the best.

Responses of Bilevel Ventilators to Unintentional Leak: A Bench Study.

BACKGROUND: The impact of leaks has mainly been assessed in bench models using continuous leak patterns which did not reflect real-life leakage. We aimed to assess the impact of the pattern and intensity of unintentional leakage (UL) using several respiratory models. METHODS: An active artificial lung (ASL 5000) was connected to three bilevel-ventilators set in pressure mode; the experiments were carried out with three lung mechanics (COPD, OHS and NMD) with and without upper airway obstruction. Triggering delay, work of breathing, pressure rise time, inspiratory pressure, tidal volume, cycling delay and the asynchrony index were measured at 0, 6, 24 and 36 L/min of UL. We generated continuous and inspiratory UL. RESULTS: Compared to 0 L/min of UL, triggering delays were significantly higher with 36 L/min of UL (+27 ms) and pressure rise times were longer (+71 ms). Cycling delays increased from -4 [-250-169] ms to 150 [-173-207] ms at, respectively 0 L/min and 36 L/min of UL and work of breathing increased from 0.15 [0.12-0.29] J/L to 0.19 [0.16-0.36] J/L. Inspiratory leakage pattern significantly increased triggering delays (+35 ms) and cycling delays (+263 ms) but decreased delivered pressure (-0.94 cmH2O) compared to continuous leakage pattern. Simulated upper airway obstruction significantly increased triggering delay (+199 ms), cycling delays (+371 ms), and decreased tidal volume (-407 mL) and pressure rise times (-56 ms). CONCLUSIONS: The pattern of leakage impacted more the device performances than the magnitude of the leakage per se. Flow limitation negatively reduced all ventilator performances.

Cause analysis of PM2.5 pollution during the COVID-19 lockdown in Nanning, China.

To analyse the cause of the atmospheric PM2.5 pollution that occurred during the COVID-19 lockdown in Nanning, Guangxi, China, a single particulate aerosol mass spectrometer, aethalometer, and particulate Lidar coupled with monitoring near-surface gaseous pollutants, meteorological conditions, remote fire spot sensing by satellite and backward trajectory models were utilized during 18-24 February 2020. Three haze stages were identified: the pre-pollution period (PPP), pollution accumulation period (PAP) and pollution dissipation period (PDP). The dominant source of PM2.5 in the PPP was biomass burning (BB) (40.4%), followed by secondary inorganic sources (28.1%) and motor vehicle exhaust (11.7%). The PAP was characterized by a large abundance of secondary inorganic sources, which contributed 56.1% of the total PM2.5 concentration, followed by BB (17.4%). The absorption Ångström exponent (2.2) in the PPP was higher than that in the other two periods. Analysis of fire spots monitored by remote satellite sensing indicated that open BB in regions around Nanning City could be one of the main factors. A planetary boundary layer-relative humidity-secondary particle matter-particulate matter positive feedback mechanism was employed to elucidate the atmospheric processes in this study. This study highlights the importance of understanding the role of BB, secondary inorganic sources and meteorology in air pollution formation and calls for policies for emission control strategies.

Ecological risk of human health in sediments in a karstic river basin with high longevity population.

Health and longevity are common human goals, and environmental factors can have significant impacts on human health. This study aims to investigate the historical changes and sources of trace elements in the sediments of a typical karstic river basin with high longevity population in Hechi City, Guangxi, China and to evaluate the ecological risks of trace elements in sediments. The results showed that over the past 100 years, the contents of trace elements in the sediments were lower in the upper reaches than in the middle and lower reaches of the river. The sediments had high trace element contents in 1950-1959 and 1989-1998, while low contents appeared after 1998. These periods correspond to China's industrial growth in the early 1950s, the Great Leap Forward movement in the late 1950s, the reform and opening-up policy implemented in the 1980s-1990s and the environmental protection policies to strengthen pollution control that have been implemented since 2000. Limestone soil and carbonate rock are the main sources of sediment in the basin. Although the geological background values of Cd and other trace elements in the basin were relatively high, the high calcium content and alkalinity of the water and sediment in the basin reduced the bioavailability of Cd and other heavy metals. The mainstream of Panyang River had a low environmental risk, but the tributary Bama River where there is dense population poses a moderate risk.

Dose variability of supplemental oxygen therapy with open patient interfaces based on in vitro measurements using a physiologically realistic upper airway model.

BACKGROUND: Supplemental oxygen therapy is widely used in hospitals and in the home for chronic care. However, there are several fundamental problems with the application of this therapy such that patients are often exposed to arterial oxygen concentrations outside of the intended target range. This paper reports volume-averaged tracheal oxygen concentration measurements (FtO2) from in vitro experiments conducted using a physiologically realistic upper airway model. The goal is to provide data to inform a detailed discussion of the delivered oxygen dose. METHODS: A baseline FtO2 dataset using a standard, straight adult nasal cannula was established by varying tidal volume (Vt), breathing frequency (f), and continuous oxygen flow rate (QO2) between the following levels to create a factorial design: Vt = 500, 640, or 800 ml; f = 12, 17, or 22 min- 1; QO2 = 2, 4, or 6 l/min. Further experiments were performed to investigate the influence on FtO2 of variation in inspiratory/expiratory ratio, inclusion of an inspiratory or expiratory pause, patient interface selection (e.g. nasal cannula versus a facemask), and rapid breathing patterns in comparison with the baseline measurements. RESULTS: Oxygen concentration measured at the trachea varied by as much as 60% (i.e. from 30.2 to 48.0% of absolute oxygen concentration) for the same oxygen supply flow rate due to variation in simulated breathing pattern. Among the baseline cases, the chief reasons for variation were 1) the influence of variation in tidal volume leading to variable FiO2 and 2) variation in breathing frequency affecting volume of supplemental oxygen delivered through the breath. CONCLUSION: For oxygen administration using open patient interfaces there was variability in the concentration and quantity of oxygen delivered to the trachea over the large range of scenarios studied. Of primary importance in evaluating the oxygen dose is knowledge of the breathing parameters that determine the average inhalation flow rate relative to the oxygen flow rate. Otherwise, the oxygen dose cannot be determined.

Impact of leaks and ventilation parameters on the efficacy of humidifiers during home ventilation for tracheostomized patients: a bench study.

BACKGROUND: During invasive ventilation, the upper airway is bypassed and no longer participates in humidification of inspired gases, which is essential to avoid harmful consequences such as endotracheal tube occlusion. In the case of increased air flow, especially in the presence of leaks (intentional or unintentional), the humidification provided by humidifiers may become ineffective. The objective of this bench study was to evaluate the quality of humidification provided by heated humidifiers under various home ventilation conditions. METHODS: Five heated humidifiers were tested in eight configurations combining circuit (expiratory valve or vented circuit), tidal volume (600 or 1000 mL) and presence of unintentional leak. Absolute humidity (AH) was measured at the upstream of the test lungs, which were placed in a 34 °C environmental chamber in order to simulate body temperature. RESULTS: The AH measured in the valve circuit ranged between 30 mg/L and 40 mg/L and three out of the five humidifiers achieved an AH higher than the recommended level (33 mg/L). With the vented circuit without unintentional leak, when tidal volume was set at 600 mL, all humidifiers reached an AH higher than 33 mg/L except one device; when the tidal volume was set at 1000 mL and unintentional leak was present, four out of the five humidifiers provided an AH lower than 33 mg/L. CONCLUSION: This study shows that, except under certain home ventilation conditions, such as high tidal volumes with unintentional leak in vented circuit, most heated humidifiers ensure sufficient humidification to avoid the risk of side effect in patients.

In Vitro-In Silico Comparison of Pulsed Oxygen Delivery From Portable Oxygen Concentrators Versus Continuous Flow Oxygen Delivery.

BACKGROUND: Portable oxygen concentrators (POCs) deliver oxygen in intermittent pulses. The challenge of establishing equivalence between continuous flow oxygen and nominal pulse flow settings on different POCs is well known. In vitro bench measurements and in silico mathematical modeling were used to compare the performance of 4 POCs versus continuous flow oxygen by predicting the FIO2 at the trachea and entering the acini. METHODS: Each of the 4 POCs was connected to a 3-dimensional printed replica of a human adult nasal airway via nasal cannula. A test lung simulated 3 breathing patterns representative of a patient with COPD at rest, during exercise, and while asleep. POCs were tested for each breathing pattern at all integer pulse flow settings. Volume-averaged FIO2 was calculated by analyzing oxygen concentrations and inhalation flow over time. In vitro oxygen waveforms were then combined with a single-path mathematical model of the lungs to assess oxygen transport through the conducting airways. In vitro experiments and mathematical modeling were repeated for continuous flow oxygen. RESULTS: Continuous flow oxygen consistently delivered more (>2% absolute) oxygen in terms of volume-averaged FIO2 for all nominally equivalent pulse flow settings of >2. Differences were also observed when comparing performances between different POCs, particularly at high device settings (5 and 6). Simulations showed that efficiency of delivery to the acinar region of the lungs was higher in pulse flow than in continuous flow oxygen but that continuous flow oxygen generally delivered a higher absolute volume of oxygen. Differences in absolute oxygen delivery per breath between continuous flow oxygen and pulse flow were smaller for acinar delivery than for tracheal delivery. CONCLUSIONS: Significant differences in POC performance based on volume-averaged FIO2 were found between pulse flow and continuous flow oxygen, and among pulse flow modes in different POCs. Although pulse flow was a more efficient mode of delivery than continuous flow oxygen, continuous flow oxygen delivered a greater absolute volume of oxygen per breath.

Mimicking a flow-limited human upper airway using a collapsible tube: relationships between flow patterns and pressures in a respiratory model.

The upper airway (UA) in humans is commonly modeled as a Starling resistor. However, negative effort dependence (NED) observed in some patients with obstructive sleep apnea (OSA) contradicts predictions based on the Starling resistor model in which inspiratory flow is independent of inspiratory driving pressure when flow is limited. In a respiratory bench model consisting of a collapsible tube and an active lung model (ASL5000), inspiratory flow characteristics were investigated in relation to upstream, downstream, and extra-luminal pressures (denoted as Pus, Pds, and Pout, respectively) by varying inspiratory effort (muscle pressure) from -1 to -20 cmH2O in the active lung. Pus was provided by a constant airway pressure device and varied from 4 to 20 cmH2O, and Pout was set at 10 and 15 cmH2O. Upstream resistance at onset of flow limitation and critical transmural pressure (Ptm) corresponding to opening of the UA were found to be independent of Pus, Pds, and Pout. With fixed Ptm, when Pds fell below a specific value (Pds'), inspiratory peak flow became constant and independent of Pds. NED plateau flow patterns at mid-inspiration (V̇n) were produced within the current bench setting when Pds fell below Pds'. V̇n was proportional to Pds, and the slope (ΔV̇n/ΔPds) increased linearly with Ptm. Ptm and Pds were the two final independent determinants of inspiratory flow. Our bench model closely mimics a flow-limited human UA, and the findings have implications for OSA treatment and research, especially for bench-testing auto-titrating devices in a more physiological way. NEW & NOTEWORTHY A respiratory model consisting of a collapsible tube was used to mimic a flow-limited human upper airway. Flow-limited breathing patterns including negative effort dependence were produced. Transmural and downstream pressures acting on the tube are the two independent determinants of the resulting inspiratory flow during flow limitation. The findings have implications for obstructive sleep apnea treatment and research, especially for bench-testing auto-titrating devices in a more physiological way.

Testing the Performance of Positive Airway Pressure Generators: From Bench to Bedside.

Positive airway pressure (PAP) devices use different proprietary algorithms for sleep-disordered breathing event detection and response. Most device evaluations are based on clinical studies, which have obvious limitations. As a complementary approach, bench studies provide an analysis of algorithms in predefined conditions, which allows understanding contradictory results observed in clinical studies. But such studies cannot provide long-term treatment data and physiologic effects of treatment. It is important to understand the advantages and the limitations of both kinds of studies. Combining results of bench tests and clinical studies is essential to improve the management of patients with PAP treatment.

Combined effects of leaks, respiratory system properties and upper airway patency on the performance of home ventilators: a bench study.

BACKGROUND: Combined effects of leaks, mechanical property of respiratory system and upper airway (UA) patency on patient-ventilator synchrony (PVA) and the level of clinically "tolerable" leaks are not well established in home ventilators. METHODS: We comparatively assessed on a bench model, the highest leak level tolerated without inducing significant asynchrony ("critical leak") in three home ventilators (Astral 150, Trilogy 100 and Vivo 60; noted as A150, T100 and V60 respectively) subjected to three simulated diseased respiratory conditions: chronic obstructive pulmonary disease (COPD), obesity hypoventilation (OHS) and neuromuscular disorders (NMD), with both open and closed UA. Also, total leak values in the device reports were compared to the bench-measured values. RESULTS: With open UA, all ventilators were able to avoid asynchrony up to a 30 L/min leak and even to 55 L/min in some cases. UA closure and respiratory diseases especially OHS influenced PVA. With closed UA, the critical leak of A150 and T100 remained higher than 55 L/min in COPD and OHS, while for V60 decreased to 41 and 33 L/min respectively. In NMD with closed UA, only T100 reached a high critical leak of 69 L/min. Besides, inspiratory trigger sensitivity change was often necessary to avoid PVA. CONCLUSIONS: Home ventilators were able to avoid PVA in high-level leak conditions. However, asynchrony appeared in cases of abnormal mechanical properties of respiratory system or closed UA. In case of closed UA, the EPAP should be adjusted prior to the inspiratory trigger. TRIAL REGISTRATION: Not applicable.

Influence of critical closing pressure on systemic vascular resistance and total arterial compliance: A clinical invasive study.

BACKGROUND: Systemic vascular resistance (SVR) and total arterial compliance (TAC) modulate systemic arterial load, and their product is the time constant (Tau) of the Windkessel. Previous studies have assumed that aortic pressure decays towards a pressure asymptote (P∞) close to 0mmHg, as right atrial pressure is considered the outflow pressure. Using these assumptions, aortic Tau values of ∼1.5seconds have been documented. However, a zero P∞ may not be physiological because of the high critical closing pressure previously documented in vivo. AIMS: To calculate precisely the Tau and P∞ of the Windkessel, and to determine the implications for the indices of systemic arterial load. METHODS: Aortic pressure decay was analysed using high-fidelity recordings in 16 subjects. Tau was calculated assuming P∞=0mmHg, and by two methods that make no assumptions regarding P∞ (the derivative and best-fit methods). RESULTS: Assuming P∞=0mmHg, we documented a Tau value of 1372±308ms, with only 29% of Windkessel function manifested by end-diastole. In contrast, Tau values of 306±109 and 353±106ms were found from the derivative and best-fit methods, with P∞ values of 75±12 and 71±12mmHg, and with ∼80% completion of Windkessel function. The "effective" resistance and compliance were ∼70% and ∼40% less than SVR and TAC (area method), respectively. CONCLUSION: We did not challenge the Windkessel model, but rather the estimation technique of model variables (Tau, SVR, TAC) that assumes P∞=0. The study favoured a shorter Tau of the Windkessel and a higher P∞ compared with previous studies. This calls for a reappraisal of the quantification of systemic arterial load.

Comparison of pulsed versus continuous oxygen delivery using realistic adult nasal airway replicas.

BACKGROUND: Portable oxygen concentrators (POCs) typically include pulse flow (PF) modes to conserve oxygen. The primary aims of this study were to develop a predictive in vitro model for inhaled oxygen delivery using a set of realistic airway replicas, and to compare PF for a commercial POC with steady flow (SF) from a compressed oxygen cylinder. METHODS: Experiments were carried out using a stationary compressed oxygen cylinder, a POC, and 15 adult nasal airway replicas based on airway geometries derived from medical images. Oxygen delivery via nasal cannula was tested at PF settings of 2.0 and 6.0, and SF rates of 2.0 and 6.0 L/min. A test lung simulated three breathing patterns representative of a chronic obstructive pulmonary disease patient at rest, during exercise, and while asleep. Volume-averaged fraction of inhaled oxygen (FiO2) was calculated by analyzing oxygen concentrations sampled at the exit of each replica and inhalation flow rates over time. POC pulse volumes were also measured using a commercial O2 conserver test system to attempt to predict FiO2 for PF. RESULTS: Relative volume-averaged FiO2 using PF ranged from 68% to 94% of SF values, increasing with breathing frequency and tidal volume. Three of 15 replicas failed to trigger the POC when used with the sleep breathing pattern at the 2.0 setting, and four of 15 replicas failed to trigger at the 6.0 setting. FiO2 values estimated from POC pulse characteristics followed similar trends but were lower than those derived from airway replica experiments. CONCLUSION: For the POC tested, PF delivered similar, though consistently lower, volume-averaged FiO2 than SF rates equivalent to nominal PF settings. Assessment of PF oxygen delivery using POC pulse characteristics alone may be insufficient; testing using airway replicas is useful in identifying possible cases of failure and may provide a better assessment of FiO2.

An in silico analysis of oxygen uptake of a mild COPD patient during rest and exercise using a portable oxygen concentrator.

Oxygen treatment based on intermittent-flow devices with pulse delivery modes available from portable oxygen concentrators (POCs) depends on the characteristics of the delivered pulse such as volume, pulse width (the time of the pulse to be delivered), and pulse delay (the time for the pulse to be initiated from the start of inhalation) as well as a patient's breathing characteristics, disease state, and respiratory morphology. This article presents a physiological-based analysis of the performance, in terms of blood oxygenation, of a commercial POC at different settings using an in silico model of a COPD patient at rest and during exercise. The analysis encompasses experimental measurements of pulse volume, width, and time delay of the POC at three different settings and two breathing rates related to rest and exercise. These experimental data of device performance are inputs to a physiological-based model of oxygen uptake that takes into account the real dynamic nature of gas exchange to illustrate how device- and patient-specific factors can affect patient oxygenation. This type of physiological analysis that considers the true effectiveness of oxygen transfer to the blood, as opposed to delivery to the nose (or mouth), can be instructive in applying therapies and designing new devices.