Compact Numerical Aperture 0.5 Fiber Optic Spectrometer Design Using Active Image Plane Tilt.

The numerical aperture of the spectrometer is crucial for weak signal detection. The transmission lens-based configuration has more optimization variations, and the grating can work approximately in the Littrow condition; thus, it is easier to acquire high numerical aperture (NA). However, designing a large aperture focusing lens remains challenging, and thus, ultra-high NA spectrometers are still difficult to acquire. In this paper, we propose a method of setting image plane tilt ahead directly when designing the large aperture focusing lens to simplify the high NA spectrometer design. By analyzing the accurate demands of the focusing lens, it can be concluded that a focusing lens with image plane tilt has much weaker demand for achromatism, and other monochromatic aberration can also be reduced, which is helpful to increase the NA. An NA0.5 fiber optic spectrometer design is given to demonstrate the proposed method. The design results show that the NA can achieve 0.5 using four lenses of two materials, and the MTF is higher than 0.5 when the spectral dispersion length is 12.5 mm and the pixel size is 25 µm, and thus, the spectral resolution can achieve 6.5 nm when the spectral sampling ratio is 2:1. The proposed method can provide reference for applications when appropriate materials are limited and high sensitivity is necessary.

Achieving highly stable sodium metal batteries with self-adapting and high-ionic-mobility ceramic fiber membranes.

Tough issues like sodium (Na) dendrite growth and poor anode reversibility hinder the practical application of sodium metal batteries (SMBs) with moderate liquid electrolytes. To settle these problems, using a smart self-adapting Al2SiO5 ceramic fiber (CF) membrane is demonstrated to enable homogeneous Na depositions and inhibit the dendritic growth. This inorganic membrane itself has superb thermal stability, high ionic mobility (Na+ transference number: 0.65) and electrolyte wettability over traditional glass fiber (GF) or polymeric ones, guaranteeing the low voltage polarization (14 mV) and long-cyclic lifetime (over 600 h) in symmetric cells testing. Notably, aluminous components in CF membranes would interact with F-based molecules in the electrolyte phase, thereby releasing some Al3+ species that can be electrochemically deposited onto the anodic interface. The packed (+)Na3V2(PO4)3|CF|Na(-) full SMBs exhibit far superior cyclic stability (capacity retention over 78.7 % after 600 cycles at 1C) than other counterparts. The in-situ detection/postmortem analysis reveal that Al/F-based inorganics formed in as-built SEI layers play a vital role in Na metal anode protection. This work may provide a viable strategy to overcome the constraints of high-energy SMBs in practical applications.

Boosting the Ultrastable High-Na-Content P2-type Layered Cathode Materials with Zero-Strain Cation Storage via a Lithium Dual-Site Substitution Approach.

P2-type layered transition-metal (TM) oxides, NaxTMO2, are highly promising as cathode materials for sodium-ion batteries (SIBs) due to their excellent rate capability and affordability. However, P2-type NaxTMO2 is afflicted by issues such as Na+/vacancy ordering and multiple phase transitions during Na-extraction/insertion, leading to staircase-like voltage profiles. In this study, we employ a combination of high Na content and Li dual-site substitution strategies to enhance the structural stability of a P2-type layered oxide (Na0.80Li0.024[Li0.065Ni0.22Mn0.66]O2). The experimental results reveal that these approaches facilitate the oxidation of Mn ions to a higher valence state, thereby affecting the local environment of both TM and Na ions. The resulting modification in the local structure significantly improves the Na-ion storage capabilities as required for cathode materials in SIBs. Furthermore, it induces a solid-solution reaction and enables nearly zero-strain operation (ΔV = 0.7%) in the Na0.80Li0.024[Li0.065Ni0.22Mn0.66]O2 cathode during cycling. The assembled full cells demonstrate an exceptional rate performance, with a retention rate of 87% at 10 C compared to that of 0.1 C, as well as an ultrastable cycling capability, maintaining a capacity retention of 73% at 2 C after 1000 cycles. These findings offer valuable insights into the electronic and structural chemistry of ultrastable cathode materials with "zero-strain" Na-ion storage.

Dual-wavelength UV-visible metalens for multispectral photoacoustic microscopy: A simulation study.

Photoacoustic microscopy is advancing with research on utilizing ultraviolet and visible light. Dual-wavelength approaches are sought for observing DNA/RNA- and vascular-related disorders. However, the availability of high numerical aperture lenses covering both ultraviolet and visible wavelengths is severely limited due to challenges such as chromatic aberration in the optics. Herein, we present a groundbreaking proposal as a pioneering simulation study for incorporating multilayer metalenses into ultraviolet-visible photoacoustic microscopy. The proposed metalens has a thickness of 1.4 µm and high numerical aperture of 0.8. By arranging cylindrical hafnium oxide nanopillars, we design an achromatic transmissive lens for 266 and 532 nm wavelengths. The metalens achieves a diffraction-limited focal spot, surpassing commercially available objective lenses. Through three-dimensional photoacoustic simulation, we demonstrate high-resolution imaging with superior endogenous contrast of targets with ultraviolet and visible optical absorption bands. This metalens will open new possibilities for downsized multispectral photoacoustic microscopy in clinical and preclinical applications.

Dielectric Response Spectroscopy as Means to Investigate Interfacial Effects for Ultra-Thin Film Polymer-Based High NA EUV Lithography.

Extreme ultra-violet lithography (EUVL) is the leading-edge technology to produce advanced nanoelectronics. The further development of EUVL is heavily based on implementing the so-called high numerical aperture (NA) EUVL, which will enable even smaller pitches up to 8 nm half pitch (HP). In anticipation of this high NA technology, it is crucial to assess the readiness of the current resist materials for the high NA regime to comply with the demanding requirements of resolution, line-edge roughness, and sensitivity (RLS). The achievable tighter pitches require lower film thicknesses for both resist and underlying transfer layers. A concern that is tied to the thinning down is the potential change in resist properties and behavior due to the interaction with the underlayer. To increase the fundamental understanding of ultra-thin films for high NA EUVL, a method to investigate the interplay of reduced film thickness and different patterning-relevant underlayers is developed by looking at the glass transition temperature (Tg) of polymer-based resists. To minimize the ambiguity of the results due to resist additives (i.e., photoacid generator (PAG) and quencher), it was opted to move forward with polymer-only samples, the main component of the resist, at this stage of the investigation. By using dielectric response spectroscopy, the results obtained show that changing the protection group of the polymer, as well as altering the polymer film thickness impacts the dynamics of the polymer mobility, which can be assessed through the Tg of the system. Unexpectedly, changing the underlayer did not result in a clear change in the polymer mobility at the tested film thicknesses.

Identification of Alternative Mitochondrial Electron Transport Pathway Components in Chickpea Indicates a Differential Response to Salinity Stress between Cultivars.

All plants contain an alternative electron transport pathway (AP) in their mitochondria, consisting of the alternative oxidase (AOX) and type 2 NAD(P)H dehydrogenase (ND) families, that are thought to play a role in controlling oxidative stress responses at the cellular level. These alternative electron transport components have been extensively studied in plants like Arabidopsis and stress inducible isoforms identified, but we know very little about them in the important crop plant chickpea. Here we identify AP components in chickpea (Cicer arietinum) and explore their response to stress at the transcript level. Based on sequence similarity with the functionally characterized proteins of Arabidopsis thaliana, five putative internal (matrix)-facing NAD(P)H dehydrogenases (CaNDA1-4 and CaNDC1) and four putative external (inter-membrane space)-facing NAD(P)H dehydrogenases (CaNDB1-4) were identified in chickpea. The corresponding activities were demonstrated for the first time in purified mitochondria of chickpea leaves and roots. Oxidation of matrix NADH generated from malate or glycine in the presence of the Complex I inhibitor rotenone was high compared to other plant species, as was oxidation of exogenous NAD(P)H. In leaf mitochondria, external NADH oxidation was stimulated by exogenous calcium and external NADPH oxidation was essentially calcium dependent. However, in roots these activities were low and largely calcium independent. A salinity experiment with six chickpea cultivars was used to identify salt-responsive alternative oxidase and NAD(P)H dehydrogenase gene transcripts in leaves from a three-point time series. An analysis of the Na:K ratio and Na content separated these cultivars into high and low Na accumulators. In the high Na accumulators, there was a significant up-regulation of CaAOX1, CaNDB2, CaNDB4, CaNDA3 and CaNDC1 in leaf tissue under long term stress, suggesting the formation of a stress-modified form of the mitochondrial electron transport chain (mETC) in leaves of these cultivars. In particular, stress-induced expression of the CaNDB2 gene showed a striking positive correlation with that of CaAOX1 across all genotypes and time points. The coordinated salinity-induced up-regulation of CaAOX1 and CaNDB2 suggests that the mitochondrial alternative pathway of respiration is an important facet of the stress response in chickpea, in high Na accumulators in particular, despite high capacities for both of these activities in leaf mitochondria of non-stressed chickpeas.

Mega High Utilization of Sodium Metal Anodes Enabled by Single Zinc Atom Sites.

Low utilization of active metallic sodium (Na) and uncontrollable growth of Na dendrites remain significant challenges for high-performance Na metal batteries, which are limited to inefficient Na utilization (<1%) and shallow cycling conditions (0.25-1.0 mAh cm-2). In this work, a kind of Na metal anode with record-high utilization and long-term cycling stability is reported, using carbon-substrate-supported nitrogen-anchored zinc (Zn) single atoms as a current collector. Single Zn atom sites which serve as a strong "magnet" for Na ions, can guide the metallic Na uniform nucleation and free from dendrite-induced short circuit. The nucleation overpotential of our strategy is essentially zero, where most of the reported modified substrates were greatly exceed 20 mV. Specifically, the Na anodes exhibit a high Na stripping/plating Coulombic efficiency with 99.8% over 350 cycles and a stable voltage response with small voltage hysteresis after cycling 1000 h. The full cell exhibits high Na utilization up to 100% and superior long-term cycling stability for more than 1000 cycles with excellent capacity retention. In terms of lifetime and Na utilization, the Na metal anodes based on our strategy significantly outperforms the reported state-of-the-art Na metal anodes. Moreover, this affords new insights into the controllable Na nucleation behavior and high Na utilization and sheds fresh light on atomic level design of an electrode for Na metal anodes.

Metasurface-Integrated Photonic Platform for Versatile Free-Space Beam Projection with Polarization Control.

Densely integrated photonic circuits enable scalable, complex processing of optical signals, including modulation, multiplexing, wavelength conversion, and detection. Directly interfacing such integrated circuits to free-space optical modes will enable novel optical functions, such as chip-scale sensing, interchip free-space interconnect and cooling, trapping, and interrogation of atoms. However, doing this within the limits of planar batch fabrication requires new approaches for bridging the large mode scale mismatch. Here, by integrating a dielectric metasurface with an extreme photonic mode converter, we create a versatile nanophotonic platform for efficient coupling to arbitrary-defined free-space radiation of 780 nm wavelength with well-controlled spatially-dependent polarization, phase, and intensity. Without leaving the chip, the high index photonic mode is converted first to a ≈ 200 µm wide, precisely collimated, linearly-polarized Gaussian beam, which is then modified by a planar, integrated, low-loss metasurface. We demonstrate high numerical aperture, diffraction limited focusing to an ≈ 473 nm spot at an ≈ 75 µm working distance, and combine it with simultaneous conversion from linear to elliptical polarization. All device components are lithographically defined and can be batch fabricated, facilitating future chip-scale low-cost hybrid photonic systems for bio-sensing, nonlinear signal processing and atomic quantum sensing, frequency references and memory.

Long-Period Gratings in Highly Germanium-Doped, Single-Mode Optical Fibers for Sensing Applications.

Long-period fiber gratings (LPGs) are well known for their sensitivity to external influences, which make them interesting for a large number of sensing applications. For these applications, fibers with a high numerical aperture (i.e., fibers with highly germanium (Ge)-doped fused silica fiber cores) are more attractive since they are intrinsically photosensitive, as well as less sensitive to bend- and microbend-induced light attenuations. In this work, we introduce a novel method to inscribe LPGs into highly Ge-doped, single-mode fibers. By tapering the optical fiber, and thus, tailoring the effective indices of the core and cladding modes, for the first time, an LPG was inscribed into such fibers using the amplitude mask technique and a KrF excimer laser. Based on this novel method, sensitive LPG-based fiber optic sensors only a few millimeters in length can be incorporated in bend-insensitive fibers for use in various monitoring applications. Moreover, by applying the described inscription method, the LPG spectrum can be influenced and tailored according to the specific demands of a particular application.

Aberration-corrected cryoimmersion light microscopy.

Cryogenic fluorescent light microscopy of flash-frozen cells stands out by artifact-free fixation and very little photobleaching of the fluorophores used. To attain the highest level of resolution, aberration-free immersion objectives with accurately matched immersion media are required, but both do not exist for imaging below the glass-transition temperature of water. Here, we resolve this challenge by combining a cryoimmersion medium, HFE-7200, which matches the refractive index of room-temperature water, with a technological concept in which the body of the objective and the front lens are not in thermal equilibrium. We implemented this concept by replacing the metallic front-lens mount of a standard bioimaging water immersion objective with an insulating ceramic mount heated around its perimeter. In this way, the objective metal housing can be maintained at room temperature, while creating a thermally shielded cold microenvironment around the sample and front lens. To demonstrate the range of potential applications, we show that our method can provide superior contrast in Escherichia coli and yeast cells expressing fluorescent proteins and resolve submicrometer structures in multicolor immunolabeled human bone osteosarcoma epithelial (U2OS) cells at [Formula: see text]C.

Effects of High and Low Sodium Diet on Plasma Amino Acid Levels in Korean Adult Women

This study was performed to determine the effect of dietary Na levels on plasma amino acid levels. Plasma amino acid levels were compared in 20 adult healthy women subjects who were given high Na diet (290.48 mEq/day : NaCl 17 g) or low Na diet (51.26 mEq/day : NaCl 3 g) for subsequent 6 days. Plasma essential amino acids levels were significantly decreased (36%) while plasma non-essential amino acids levels were significantly increased (22%) when subjects were given low Na diet (p < 0.001). Among essential amino acids, threonine was decreased (74%) significantly when subjects were given low Na diet (p < 0.01). Among nonessential amino acids, serine (49%), proline (20%) and aspartic acid (14%) were increased (p < 0.01), while arginine (48%) and glutamic acid (27%) were decreased (p < 0.001). In conclusion, dietary Na contents seemed to be an important factor to affect plasma amino acid levels. It would be appropriate to decrease the dietary Na intakes level considering the various clinical effects of dietary Na on the body fluid. For the patients who need low Na diet, it would be suggested that the level of dietary proteins should be carefully considered along with dietary Na manipulation.