Ionic Thermoelectric Generators in Vertical and Planar Topologies Based on Fluorinated Polymer Hybrid Materials with Ionic Liquids.

Ionic thermoelectrics (TEs), in which voltage generation is based on ion migration, are suitable for applications based on their low cost, high flexibility, high ionic conductivity, and wide range of Seebeck coefficients. This work reports on the development of ionic TE materials based on the poly(vinylidene fluoride-trifluoroethylene), Poly(VDF-co-TrFE), as host polymer blended with different contents of the ionic liquid, IL, 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, [EMIM][TFSI]. The morphology, physico-chemical, thermal, mechanical, and electrical properties of the samples are evaluated together with the TE response. It is demonstrated that the IL acts as a nucleating agent for polymer crystallization. The mechanical properties and ionic conductivity values are dependent on the IL content. A high room temperature ionic conductivity of 0.008 S cm-1 is obtained for the sample with 60 wt% of [EMIM][TFSI] IL. The TE properties depend on both IL content and device topology-vertical or planar-the largest generated voltage range being obtained for the planar topology and the sample with 10 wt% of IL content, characterized by a Seebeck coefficient of 1.2 mV K-1. Based on the obtained maximum power density of 4.9 µW m-2, these materials are suitable for a new generation of TE devices.

Biodegradable and biocompatible collagen-based hybrid materials for force sensing applications.

With the aim of replacing synthetic macromolecules by biological macromolecules for advanced applications, collagen films were produced with two different ionic liquids (ILs), choline dihydrogen phosphate ([Ch][DHP]) and choline serinate ([Ch][Seri]), added in order to modulate the electrical responses. The films were prepared by casting, varying IL content between 0 and 6 wt%. The morphology and thermal properties of the resulting films were found to be independent of both IL type and content. However, the highest direct curret (d.c.) electrical conductivity (1.4 × 10-8 S·cm-1) was achieved for collagen films containing 3 wt% [Ch][DHP]. Furthermore, it was demonstrated that IL/collagen films were non-cytotoxic, with cell activity values exceeding 70 %. These collagen films were proven to be suitable for force sensing applications, displaying excellent sensitivity and stability upon repeated testing.

Sustainable Collagen Composites with Graphene Oxide for Bending Resistive Sensing.

This work reports on the development of collagen films with graphene oxide nanoparticles (GO NPs), aiming toward the development of a new generation of functional sustainable sensors. For this purpose, different GO NP contents up to 3 wt % were incorporated into a collagen matrix, and morphological, thermal, mechanical and electrical properties were evaluated. Independently of the GO NP content, all films display an increase in thermal stability as a result of the increase in the structural order of collagen, as revealed by XRD analysis. Further, the inclusion of GO NPs into collagen promotes an increase in the intensity of oxygen characteristic absorption bands in FTIR spectra, due to the abundant oxygen-containing functional groups, which lead to an increase in the hydrophilic character of the surface. GO NPs also influence the mechanical properties of the composites, increasing the tensile strength from 33.2 ± 2.4 MPa (collagen) to 44.1 ± 1.0 MPa (collagen with 3 wt % GO NPs). Finally, the electrical conductivity also increases slightly with GO NP content, allowing the development of resistive bending sensors.

Smart and Multifunctional Materials Based on Electroactive Poly(vinylidene fluoride): Recent Advances and Opportunities in Sensors, Actuators, Energy, Environmental, and Biomedical Applications.

From scientific and technological points of view, poly(vinylidene fluoride), PVDF, is one of the most exciting polymers due to its overall physicochemical characteristics. This polymer can crystalize into five crystalline phases and can be processed in the form of films, fibers, membranes, and specific microstructures, being the physical properties controllable over a wide range through appropriate chemical modifications. Moreover, PVDF-based materials are characterized by excellent chemical, mechanical, thermal, and radiation resistance, and for their outstanding electroactive properties, including high dielectric, piezoelectric, pyroelectric, and ferroelectric response, being the best among polymer systems and thus noteworthy for an increasing number of technologies. This review summarizes and critically discusses the latest advances in PVDF and its copolymers, composites, and blends, including their main characteristics and processability, together with their tailorability and implementation in areas including sensors, actuators, energy harvesting and storage devices, environmental membranes, microfluidic, tissue engineering, and antimicrobial applications. The main conclusions, challenges and future trends concerning materials and application areas are also presented.

Multifunctional Magnetoelectric Sensing and Bending Actuator Response of Polymer-Based Hybrid Materials with Magnetic Ionic Liquids.

With the evolution of the digital society, the demand for miniaturized multifunctional devices has been increasing, particularly for sensors and actuators. These technological translators allow successful interaction between the physical and digital worlds. In particular, the development of smart materials with magnetoelectric (ME) properties, capable of wirelessly generating electrical signals in response to external magnetic fields, represents a suitable approach for the development of magnetic field sensors and actuators due to their ME coupling, flexibility, robustness and easy fabrication, compatible with additive manufacturing technologies. This work demonstrates the suitability of magnetoelectric (ME) responsive materials based on the magnetic ionic liquid (MIL) 1-butyl-3-methylimidazolium tetrachloroferrate ([Bmim][FeCl4]) and the polymer poly(vinylidene fluoride-co-trifluoroethylene) (P(VDF-TrFE) for magnetic sensing and actuation device development. The developed sensor works in the AC magnetic field and has frequency-dependent sensitivity. The materials show voltage responses in the mV range, suitable for the development of magnetic field sensors with a highest sensitivity (s) of 76 mV·Oe-1. The high ME response (maximum ME voltage coefficient of 15 V·cm-1·Oe-1) and magnetic bending actuation (2.1 mm) capability are explained by the magnetoionic (MI) interaction and the morphology of the composites.

Influence of the Inclusion of Propylene Carbonate Electrolyte Solvent on the Microstructure and Thermal and Mechanical Stability of Poly(l-lactic acid) and Poly(vinylidene fluoride-co-hexafluoropropylene) Battery Separator Membranes.

The influence of the inclusion of the organic solvent propylene carbonate (PC) in microporous membranes based on poly(l-lactic acid) (PLLA) and poly(vinylidene fluoride-co-hexafluoropropylene) P(VDF-HFP) has been studied based on its relevance for the application of those separator membranes in lithium-ion batteries. The membranes have been produced through solvent casting and characterized with respect to the swelling ratio originated by the uptake of the organic solvent. The organic solvent uptake affects the porous microstructure and crystalline phase of both membrane types. The organic solvent uptake amount affects the crystal size of the membranes as a consequence of the interaction between the solvent and the polymer, since the presence of the solvent modifies the melting process of the polymer crystals due to a freezing temperature depression effect. It is also shown that the organic solvent partially penetrates into the amorphous phase of the polymer, leading to a mechanical plasticizing effect. Thus, the interaction between the organic solvent and the porous membrane is essential to properly tailor membrane properties, which in turn will affect lithium-ion battery performance.

High Performance Ternary Solid Polymer Electrolytes Based on High Dielectric Poly(vinylidene fluoride) Copolymers for Solid State Lithium-Ion Batteries.

Renewable energy sources require efficient energy storage systems. Lithium-ion batteries stand out among those systems, but safety and cycling stability problems still need to be improved. This can be achieved by the implementation of solid polymer electrolytes (SPE) instead of the typically used separator/electrolyte system. Thus, ternary SPEs have been developed based on poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) and poly(vinylidene fluoride-trifluoroethylene-chlorofluoroethylene), P(VDF-TrFE-CFE) as host polymers, clinoptilolite (CPT) zeolite added to stabilize the battery cycling performance, and ionic liquids (ILs) (1-butyl-3-methylimidazolium thiocyanate ([BMIM][SCN])), 1-methyl-1-propylpyrrolidinium bis(trifluoromethylsulfonyl)imide ([PMPyr][TFSI]) or lithium bis(trifluoromethanesulfonyl)imide (LiTFSI), incorporated to increase the ionic conductivity. The samples were processed by doctor blade with solvent evaporation at 160 °C. The nature of the polymer matrix and fillers affect the morphology and mechanical properties of the samples and play an important role in electrochemical parameters such as ionic conductivity value, electrochemical window stability, and lithium-transference number. The best ionic conductivity (4.2 × 10-5 S cm-1) and lithium transference number (0.59) were obtained for the PVDF-HFP-CPT-[PMPyr][TFSI] sample. Charge-discharge battery tests at C/10 showed excellent battery performance with values of 150 mAh g-1 after 50 cycles, regardless of the polymer matrix and IL used. In the rate performance tests, the best SPE was the one based on the P(VDF-TrFE-CFE) host polymer, with a discharge value at C-rate of 98.7 mAh g-1, as it promoted ionic dissociation. This study proves for the first time the suitability of P(VDF-TrFE-CFE) as SPE in lithium-ion batteries, showing the relevance of the proper selection of the polymer matrix, IL type, and lithium salt in the formulation of the ternary SPE, in order to optimize solid-state battery performance. In particular, the enhancement of the ionic conductivity provided by the IL and the effect of the high dielectric constant polymer P(VDF-TrFE-CFE) in improving battery cyclability in a wide range of discharge rates must be highlighted.

Influence of Solvent Evaporation Temperature on the Performance of Ternary Solid Polymer Electrolytes Based on Poly(vinylidene fluoride-co-hexafluoropropylene) Combining an Ionic Liquid and a Zeolite.

Solid polymer electrolytes (SPEs) will allow improving safety and durability in next-generation solid-state lithium-ion batteries (LIBs). Within the SPE class, ternary composites are a suitable approach as they provide high room-temperature ionic conductivity and excellent cycling and electrochemical stability. In this work, ternary SPEs based on poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) as a polymer host, clinoptilolite (CPT) zeolite, and 1-butyl-3-methylimidazolium thiocyanate ([Bmim][SCN])) ionic liquid (IL) as fillers were produced by solvent evaporation at different temperatures (room temperature, 80, 120, and 160 °C). Solvent evaporation temperature affects the morphology, degree of crystallinity, and mechanical properties of the samples as well as the ionic conductivity and lithium transference number. The highest ionic conductivity (1.2 × 10-4 S·cm-1) and lithium transference number (0.66) have been obtained for the SPE prepared at room temperature and 160 °C, respectively. Charge-discharge battery tests show the highest value of discharge capacity of 149 and 136 mAh·g-1 at C/10 and C/2 rates, respectively, for the SPE prepared at 160 °C. We conclude that the fine control of the solvent evaporation temperature during the preparation of the SPE allows us to optimize solid-state battery performance.

High-Performance Sustainable Electrochromic Devices Based on Carrageenan Solid Polymer Electrolytes with Ionic Liquid.

The development of sustainable functional materials with strong potential to be applied in different areas has been growing and gaining increasing interest to address the environmental impact of current materials and technologies. In this scope, this work reports on sustainable functional materials with electrochromic properties, based on their increasing interest for a variety of applications, including sensing technologies. The materials have been developed based on a natural derived polymer, carrageenan, in which different amounts of the ionic liquid (IL) 1-ethyl-3-methylimidazolium thiocyanate ([EMIM][SCN]) were blended. It is shown that the addition of different amounts of IL to the carrageenan matrix does not affect the properties of the samples in terms of morphology or physicochemical and thermal properties, the most significant difference being the increase of the ionic conductivity with increasing IL content, ranging from 2.3 × 10-11 S·cm-1 for pristine carrageenan to 4.6 × 10-4 S·cm-1 for the samples with 5 and 60 wt % IL content, respectively. A electrochromic device has been developed based on the different IL/carrageenan samples as electrolyte and poly(3,4-ethylenedioxythiophene) polystyrenesulfonate (PEDOT:PSS) as electrodes. Spectroelectrochemistry testing demonstrates functional devices at low voltages between 0.3 and -0.9 V. Among the different samples, the one with 15 wt % IL content presents the best conditions for application, presenting an oxidation time of 6 s, a reduction time of 8 s, and a charge density of 1150 and 1050 µC·cm-2 for oxidation and reduction, respectively. The same sample also presents excellent optical density as a function of load density, presenting an optical switch (Δ%Tx) of 99%. Thus, it is demonstrated that it is possible to develop high efficiency and sustainable electrochromic devices based on natural polymers and ionic liquids.

Magnetically responsive chitosan-pectin films incorporating Fe3O4 nanoparticles with enhanced antimicrobial activity.

Chitosan-pectin films with iron oxide (Fe3O4) magnetic nanoparticles were prepared by solution casting in order to produce biopolymer based magnetically active materials. Infrared (FTIR) spectra indicated physical interactions between the matrix and nanoparticles, corroborated by differential scanning calorimetry (DSC) results. In addition, thermal characterization suggested that the interactions between chitosan, pectin and the nanoparticles resulted in a less compact structure, influencing the film mechanical properties. Regarding vibrating-sample magnetometry (VSM) and electrical analysis, chitosan-pectin films with Fe3O4 nanoparticles showed ferrimagnetic behavior, with an increase of the dielectric constant as the nanoparticle concentration increased. Furthermore, films displayed enhanced antimicrobial activity against Escherichia coli (Gram-negative) and Staphylococcus epidermidis (Gram-positive) bacteria. Therefore, chitosan-pectin films with Fe3O4 magnetic nanoparticles provide promising results for active and intelligent food packaging applications.

Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) Blends with Poly(caprolactone) and Poly(lactic acid): A Comparative Study.

Poly(hydroxybutyrate-co-hidroxyvalerate) (PHBV) is a biodegradable polymer, which is a potential substitute for plastics made from fossil resources. Due to its practical interest in the field of tissue engineering, packaging, sensors, and electronic devices, the demand for PHBV with specific thermal, electrical, as well as mechanical requirements is growing. In order to improve these properties, we have developed PHBV blends with two thermoplastic biodegradable polyesters, including poly(caprolactone) (PCL) and poly(lactic acid) (PLA). We analysed the effect of these biopolymers on the morphological, wetting, structural, thermal, mechanical, and electrical characteristics of the materials. Further, the biodegradation of the samples in simulated body fluid conditions was evaluated, as well as the antibacterial activity. The results demonstrate that the blending with PCL and PLA leads to films with a dense morphology, increases the hydrophilic character, and induces a reinforcement of the mechanical characteristics with respect to pristine PHBV. In addition, a decrease in dielectric constant and a.c. electrical conductivity was noticed for PHBV/PLA and PHBV/PCL blends compared to neat PHBV polymer. All neat polymers and blends showed antibacterial properties against S. aureus, with more than 40% bacterial reduction, which increased to 72% in the presence of PCL polymer for a blend ratio of 50/50. Thus, it is demonstrated a suitable way to further tailor a variety of functionalities of PHBV for specific applications, by the development of polymer blends with PLA or PCL.

Lithium-Ion Battery Solid Electrolytes Based on Poly(vinylidene Fluoride)-Metal Thiocyanate Ionic Liquid Blends.

Solid polymer electrolytes (SPEs) are required to improve battery safety through the elimination of the liquid electrolyte solution in current batteries. This work is focused on the development of a hybrid SPE based on poly(vinylidene fluoride), PVDF, and 1-butyl-3-methylimidazolium cobalt(II) isothiocyanate, [BMIM]2[(SCN)4Co] magnetic ionic liquid (MIL), and its battery cycling behavior at room temperature. The addition of MIL in filler contents up to 40 wt % to the PVDF matrix does not influence the compact morphology of the samples obtained by solvent casting. The polar ß-phase of PVDF increases with increasing MIL content, whereas the degree of crystallinity, thermal degradation temperature, and mechanical properties of the MIL/PVDF blends decrease with increasing MIL content. The ionic conductivity of the MIL/PVDF blends increases both with temperature and MIL content, showing the highest ionic conductivity of 7 × 10-4 mS cm-1 at room temperature for the MIL/PVDF blend with 40 wt % of MIL. The cathodic half-cells prepared with this blend as SPE show good reversibility and excellent cycling behavior at different C-rates, with a discharge capacity of 80 mAh g-1 at a C/10-rate with a Coulombic efficiency of 99%. The developed magnetic SPE, with excellent performance at room temperature, shows potential for the implementation of sustainable lithium-ion batteries, which can be further tuned by the application of an external magnetic field.

Ionic Liquids as Biocompatible Antibacterial Agents: A Case Study on Structure-Related Bioactivity on Escherichia coli.

The potential of ionic liquids (ILs) to be used as antimicrobial agents for biomedical applications has been hindered by the fact that most of them are cytotoxic toward mammalian cells. Understanding the mechanism of bacterial and mammalian cellular damage of ILs is key to their safety design. In this work, we evaluate the antimicrobial activity and mode of action of several ILs with varying anions and cations toward the clinically relevant Gram-negative Escherichia coli. Langmuir monolayer technique was used to evaluate if the IL's mode of action was related to the bacterial cell membrane interaction for an effective E. coli killing. 1-Decyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide [DMIM][TFSI] and trihexyltetradecyl phosphonium bis(trifluoromethylsulfonyl) imide [P6,6,6,14][TFSI] were surface-active and induced bacterial cell lysis, through a membrane-disruption phenomenon on bacteria, in a mechanism that was clearly related to the long alkyl chains of the cation. 1-Ethyl-3-methylimidazolium hydrogen sulfate [EMIM][HSO4] was highly antimicrobial toward E. coli and found suitable for biological applications since it was harmless to mammalian cells at most of the tested concentrations. The results suggest that the imidazolium cation of the ILs is mostly responsible not only for their antimicrobial activity but also for their cytotoxicity, and the inclusion of different anions may tailor the ILs' biocompatibility without losing the capacity to kill bacteria, as is the case of [EMIM][HSO4]. Importantly, this IL was found to be highly antimicrobial even when incorporated in a polymeric matrix.

Electrospun Magnetic Ionic Liquid Based Electroactive Materials for Tissue Engineering Applications.

Functional electrospun fibers incorporating ionic liquids (ILs) present a novel approach in the development of active microenviroments due to their ability to respond to external magnetic fields without the addition of magnetic particles. In this context, this work reports on the development of magnetically responsive magneto-ionic fibers based on the electroactive polymer poly(vinylidene fluoride) and the magnetic IL (MIL), bis(1-butyl-3-methylimidazolium) tetrathiocyanatocobaltate ([Bmim]2[(SCN)4Co]). The PVDF/MIL electrospun fibers were prepared incorporating 5, 10 and 15 wt.% of the MIL, showing that the inclusion of the MIL increases the polar ß-phase content of the polymer from 79% to 94% and decreases the crystallinity of the fibers from 47% to 36%. Furthermore, the thermal stability of the fibers decreases with the incorporation of the MIL. The magnetization of the PVDF/MIL composite fibers is proportional to the MIL content and decreases with temperature. Finally, cytotoxicity assays show a decrease in cell viability with increasing the MIL content.

High-Performance Room Temperature Lithium-Ion Battery Solid Polymer Electrolytes Based on Poly(vinylidene fluoride-co-hexafluoropropylene) Combining Ionic Liquid and Zeolite.

The demand for more efficient energy storage devices has led to the exponential growth of lithium-ion batteries. To overcome the limitations of these systems in terms of safety and to reduce environmental impact, solid-state technology emerges as a suitable approach. This work reports on a three-component solid polymer electrolyte system based on poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP), the ionic liquid 1-butyl-3-methylimidazolium thiocyanate ([BMIM][SCN]), and clinoptilolite zeolite (CPT). The influences of the preparation method and of the dopants on the electrolyte stability, ionic conductivity, and battery performance were studied. The developed electrolytes show an improved room temperature ionic conductivity (1.9 × 10-4 S cm-1), thermal stability (up to 300 °C), and mechanical stability. The corresponding batteries exhibit an outstanding room temperature performance of 160.3 mAh g-1 at a C/15-rate, with a capacity retention of 76% after 50 cycles. These results represent a step forward in a promising technology aiming the widespread implementation of solid-state batteries.

Influence of cellulose nanocrystal surface functionalization on the bending response of cellulose nanocrystal/ionic liquid soft actuators.

This work reports the development of renewable cellulose nanocrystal (CNC) and ionic liquid (IL) hybrid materials for bending actuator applications. For this purpose, cellulose nanocrystals with different surface charges (neutral, positive and negative) were prepared and increasing amounts of the IL 2-hydroxy-ethyl-trimethylammonium dihydrogen phosphate ([Ch][DHP]) (10 and 25 wt%) were incorporated into the CNC hosting matrix. The morphology of the samples was evaluated, proving that both surface charge and IL incorporation do not affect the characteristic layered structure of the CNC. Atomic force microscopy results reveal a sea-island morphology in the hybrid films, where CNC bundles are surrounded by [Ch][DHP]-rich regions. An increase in the electrical conductivity is observed upon IL incorporation into the CNC matrix, regardless of the CNC surface charge. The highest electrical conductivity values are observed for IL/CNC (+) 25 wt% with an electrical conductivity of 3.18 × 10-5± 2.75 × 10-7 S cm-1 and IL/CNC (-) 10 wt% (1.26 × 10-5± 5.92 × 10-6 S cm-1). The highest bending displacement of 2.1 mm for an applied voltage of 4.0 Vpp at a frequency of 100 mHz was obtained for the IL/CNC (+) 25 wt% composite, demonstrating the suitability of cellulose to develop soft actuators.

Biodegradable Hydrogels Loaded with Magnetically Responsive Microspheres as 2D and 3D Scaffolds.

Scaffolds play an essential role in the success of tissue engineering approaches. Their intrinsic properties are known to influence cellular processes such as adhesion, proliferation and differentiation. Hydrogel-based matrices are attractive scaffolds due to their high-water content resembling the native extracellular matrix. In addition, polymer-based magnetoelectric materials have demonstrated suitable bioactivity, allowing to provide magnetically and mechanically activated biophysical electrical stimuli capable of improving cellular processes. The present work reports on a responsive scaffold based on poly (L-lactic acid) (PLLA) microspheres and magnetic microsphere nanocomposites composed of PLLA and magnetostrictive cobalt ferrites (CoFe2O4), combined with a hydrogel matrix, which mimics the tissue's hydrated environment and acts as a support matrix. For cell proliferation evaluation, two different cell culture conditions (2D and 3D matrices) and two different strategies, static and dynamic culture, were applied in order to evaluate the influence of extracellular matrix-like confinement and the magnetoelectric/magneto-mechanical effect on cellular behavior. MC3T3-E1 proliferation rate is increased under dynamic conditions, indicating the potential use of hydrogel matrices with remotely stimulated magnetostrictive biomaterials for bone tissue engineering.

Erratum: Development of Poly(l-Lactic Acid)-Based Bending Actuators. Polymers 2020, 12, 1187.

The authors wish to make a change to their published paper [...].

Design of Ionic-Liquid-Based Hybrid Polymer Materials with a Magnetoactive and Electroactive Multifunctional Response.

Multifunctional materials with sensor and actuator capabilities play an increasing role in modern technology. In this scope, hybrid materials with magnetic sensing and an electromechanical actuator response based on magnetic ionic liquids (MILs) and the polymer poly(vinylidene fluoride) (PVDF) have been developed. MILs comprising different cation alkyl chain lengths [Cnmim]+ and sharing the same anion [FeCl4]- were incorporated at 20 wt % into the PVDF matrix and the morphological, physical, chemical, and functional properties of the materials were evaluated. An increasing IL alkyl chain length leads to the formation of a porous structure, together with an increase in the electroactive PVDF ß-phase content of the polymer and a decrease in the crystallinity degree and thermal stability. The magnetic susceptibility of the [Cnmim][FeCl4]/PVDF films reveals a paramagnetic behavior. The multifunctional response is characterized by a magnetoionic response that decreases with increasing IL alkyl chain length, the highest magnetoionic coefficient (1.06 ± 0.015 V cm-1 Oe-1) being observed for [C2mim][FeCl4]/PVDF. The electromechanical actuator response is characterized by a highest displacement of 1.1 mm for the [C4mim][FeCl4]/PVDF film by applying a voltage of 4 V at a frequency of 100 mHz. Further, their solution processing makes these multiresponsive materials compatible with additive manufacturing technologies.

Cellulose Nanocrystal and Water-Soluble Cellulose Derivative Based Electromechanical Bending Actuators.

This study reports a versatile method for the development of cellulose nanocrystals (CNCs) and water-soluble cellulose derivatives (methyl cellulose (MC), hydroxypropyl cellulose (HPC), and sodium carboxymethyl cellulose (NaCMC)) films comprising the ionic liquid (IL) 2-hydroxy-ethyl-trimethylammonium dihydrogen phosphate ([Ch][DHP]) for actuator fabrication. The influence of the IL content on the morphology and physico-chemical properties of free-standing composite films was evaluated. Independently of the cellulose derivative, the ductility of the films increases upon [Ch][DHP] incorporation to yield elongation at break values of nearly 15%. An increase on the electrical conductivity as a result of the IL incorporation into cellulosic matrices is found. The actuator performance of composites was evaluated, NaCMC/[Ch][DHP] showing the maximum displacement along the x-axis of 9 mm at 8 Vpp. Based on the obtained high electromechanical actuation performance, together with their simple processability and renewable nature, the materials fabricated here represent a step forward in the development of sustainable soft actuators of high practical relevance.