Abdominal image quality and dose reduction with energy-integrating or photon-counting detectors dual-source CT: A phantom study.

PURPOSE: The purpose of this study was to assess image-quality and dose reduction potential using a photon-counting computed tomography (PCCT) system by comparison with two different dual-source CT (DSCT) systems using two phantoms. MATERIALS AND METHODS: Acquisitions on phantoms were performed using two DSCT systems (DSCT1 [Somatom Force] and DSCT2 [Somatom Pro.Pulse]) and one PCCT system (Naeotom Alpha) at four dose levels (13/6/3.4/1.8 mGy). Noise power spectrum (NPS) and task-based transfer function (TTF) were computed to assess noise magnitude and noise texture and spatial resolution (f50), respectively. Detectability indexes (d') were computed to model the detection of abdominal lesions: one unenhanced high-contrast task, one contrast-enhanced high-contrast task and one unenhanced low-contrast task. Image quality was subjectively assessed on an anthropomorphic phantom by two radiologists. RESULTS: For all dose levels, noise magnitude values were lower with PCCT than with DSCTs. For all CT systems, similar noise texture values were found at 13 and 6 mGy, but the greatest noise texture values were found for DSCT2 and the lowest for PCCT at 3.4 and 1.8 mGy. For high-contrast inserts, similar or lower f50 values were found with PCCT than with DSCT1 and the opposite pattern was found for the low-contrast insert. For the three simulated lesions, d' values were greater with PCCT than with DSCTs. Abdominal images were rated satisfactory for clinical use by the radiologists for all dose levels with PCCT and for 13 and 6 mGy with DSCTs. CONCLUSION: By comparison with DSCTs, PCCT reduces image-noise and improves detectability of simulated abdominal lesions without altering the spatial resolution and image texture. Image-quality obtained with PCCT seem to indicate greater potential for dose optimization than those obtained with DSCTs.

Comparison of low-energy virtual monoenergetic images between photon-counting CT and energy-integrating detectors CT: A phantom study.

PURPOSE: The purpose of this study was to assess image quality and dose level using a photon-counting CT (PCCT) scanner by comparison with a dual-source CT (DSCT) scanner on virtual monoenergetic images (VMIs) at low energy levels. MATERIALS AND METHODS: A phantom was scanned using a DSCT and a PCCT with a volume CT dose index of 11 mGy, and additionally at 6 mGy and 1.8 mGy for PCCT. Noise power spectrum and task-based transfer function were evaluated from 40 to 70 keV on VMIs to assess noise magnitude and noise texture (fav) and spatial resolution on two iodine inserts (f50), respectively. A detectability index (d') was computed to assess the detection of two contrast-enhanced lesions according to the energy level used. RESULTS: For all energy levels, noise magnitude values were lower with PCCT than with DSCT at 11 and 6 mGy, but greater at 1.8 mGy. fav values were higher with PCCT than with DSCT at 11 mGy (8.6 ± 1.5 [standard deviation [SD]%), similar at 6 mGy (1.6 ± 1.5 [SD]%) and lower at 1.8 mGy (-17.8 ± 2.2 [SD]%). For both inserts, f50 values were higher with PCCT than DSCT at 11- and 6 mGy for all keV levels, except at 6 mGy and 40 keV. d' values were higher with PCCT than with DSCT at 11- and 6 mGy for all keV and both simulated lesions. Similar d' values to those of the DSCT at 11 mGy, were obtained at 2.25 mGy for iodine insert at 2 mg/mL and at 0.96 mGy for iodine insert at 4 mg/mL at 40 keV. CONCLUSION: Compared to DSCT, PCCT reduces noise magnitude and improves noise texture, spatial resolution and detectability on VMIs for all low-keV levels.

Comparison of two deep-learning image reconstruction algorithms on cardiac CT images: A phantom study.

PURPOSE: The purpose of this study was to compare the performance of Precise IQ Engine (PIQE) and Advanced intelligent Clear-IQ Engine (AiCE) algorithms on image-quality according to the dose level in a cardiac computed tomography (CT) protocol. MATERIALS AND METHODS: Acquisitions were performed using the CT ACR 464 phantom at three dose levels (volume CT dose indexes: 7.1/5.2/3.1 mGy) using a prospective cardiac CT protocol. Raw data were reconstructed using the three levels of AiCE and PIQE (Mild, Standard and Strong). The noise power spectrum (NPS) and task-based transfer function (TTF) for bone and acrylic inserts were computed. The detectability index (d') was computed to model the detectability of the coronary lumen (350 Hounsfield units and 4-mm diameter) and non-calcified plaque (40 Hounsfield units and 2-mm diameter). RESULTS: Noise magnitude values were lower with PIQE than with AiCE (-13.4 ± 6.0 [standard deviation (SD)] % for Mild, -20.4 ± 4.0 [SD] % for Standard and -32.6 ± 2.6 [SD] % for Strong levels). The average NPS spatial frequencies shifted towards higher frequencies with PIQE than with AiCE (21.9 ± 3.5 [SD] % for Mild, 20.1 ± 3.0 [SD] % for Standard and 12.5 ± 3.5 [SD] % for Strong levels). The TTF values at fifty percent (f50) values shifted towards higher frequencies with PIQE than with AiCE for acrylic inserts but, for bone inserts, f50 values were found to be close. Whatever the dose and DLR level, d' values of both simulated cardiac lesions were higher with PIQE than with AiCE. For the simulated coronary lumen, d' values were better by 35.1 ± 9.3 (SD) % on average for all dose levels for Mild, 43.2 ± 5.0 (SD) % for Standard, and 62.6 ± 1.2 (SD) % for Strong levels. CONCLUSION: Compared to AiCE, PIQE reduced noise, improved spatial resolution, noise texture and detectability of simulated cardiac lesions. PIQE seems to have a greater potential for dose reduction in cardiac CT acquisition.

Determining the Optimal Energy Level of Virtual Monoenergetic Images in Dual-Source CT for Diagnosis of Bowel Obstruction and Colitis.

Images from 64 patients undergoing an enhanced abdominal-pelvis scan at portal phase in dual-energy CT mode for the diagnosis of colitis or bowel obstruction were retrospectively analyzed. Acquisitions were performed on a third-generation dual-source CT (DSCT) 100/Sn150 kVp. Mixed images were generated, as well as virtual monoenergetic images (VMIs) at 40/50/60/70 keV. Objective image quality was assessed on VMIs and mixed images by measuring contrast, noise and contrast-to-noise ratio (CNR). Noise, smoothing and overall image quality were subjectively analyzed by two radiologists using Likert scales. For both patient groups, the noise decreased significantly according to the energy level from 40 to 60 keV by -47.2 ± 24.0% for bowel obstruction and -50.4 ± 18.2% for colitis. It was similar between 60 and 70 keV (p = 0.475 and 0.059, respectively). Noise values were significantly higher in VMIs than in mixed images, except for 70 keV (p = 0.53 and 0.071, respectively). Similar results were observed for contrast values, with a decrease between 40 and 70 keV of -56.3 ± 7.9% for bowel obstruction -56.2 ± 10.9% for colitis. The maximum CNR value was found at 60 keV compared to other energy levels and mixed images, but there was no significant difference with the other energy levels apart from 70 keV (-9.7 ± 9.8%) for bowel obstruction and 40 keV (-6.6 ± 8.2%) and 70 keV (-5.8 ± 9.2%) for colitis. The VMIs at 60 keV presented higher scores for all criteria for bowel obstruction and colitis, with no significant difference in smoothing score compared to mixed images (p = 0.119 and p = 0.888, respectively).

Standard views do not suffice in assessing distal scaphoid articular cannulated screw penetration.

BACKGROUND: Articular screw penetration is one of the most common hardware-related problems after scaphoid fracture fixation, occurring in up to two-thirds of patients, in particular into the scaphotrapezotrapezoidal (STT) joint. The aim of this study was to investigate whether this clinically important issue could be detected using standard anteroposterior (AP) and lateral, as well as additional nonstandard fluoroscopic views using direct open visualization with magnifying loupes as reference standard. MATERIALS AND METHODS: Ten fresh cadaver wrists were used for this imaging study. A 2.2 mm cannulated compression screws with a length of 24 mm was placed in the scaphoid and incrementally left to protrude at the STT joint up to 2 mm. Eight fluoroscopic views of the wrist were then obtained by rotating the forearm using goniometric measurements, keeping the image beam parallel to the floor: (1) anteroposterior with the wrist in neutral rotation, (2) anteroposterior with the wrist in ulnar deviation, (3) supinated oblique 60° from neutral (60° supinated oblique), (4) supinated oblique 45° from neutral (45° supinated oblique), (5) a true lateral, (6) a true lateral with the wrist in radial deviation, (7) pronated oblique 45° from neutral (45° pronated oblique), and (8) a pronated oblique 60° from neutral (60° pronated oblique). RESULTS: Standard anteroposterior and lateral fluoroscopy views (radiographically calibrated) of a percutaneous cannulated screw fixation of a scaphoid fracture were insufficient to detect distal articular penetration, missing half the amount of screw penetrations in the current study. The 45° pronated oblique view was found as the most sensitive in detecting STT penetration (p < 0.0001). CONCLUSIONS: Standard anteroposterior and lateral fluoroscopy views of a percutaneous cannulated screw fixation of a scaphoid waist fracture are insufficient to detect STT screw penetration. According to the current study, standard views would have missed half the amount of screw penetrations, which seems to reflect the high incidence of this problem in current practice. The most sensitive view was the 45° pronated oblique view, which detected STT screw penetration in all cases. Level of Evidence Not applicable.

Brittle Bone Imaging: Diagnostic Procedures in Adults.

This article concentrates on generalized disorders causing bone fragility. The most frequent cause of brittle bone disease is osteoporosis, only diagnosed by elimination. First, malignant osteopathy must be ruled out: fracture on metastasis or multiple myeloma, which mimics osteoporosis when presenting as diffuse demineralization. Second, patients should be screened for signs of hyperparathyroidism or osteomalacia. Much more rarely, many other pathologies can lead to brittle bone by demineralization or associated increased bone density.The radiologist needs to know the clinical context and notably the patient's age (childhood or adulthood) at discovery, and known pathologies and ongoing or previous treatments: corticotherapy, bisphosphonates, denosumab, or prior radiotherapy in the affected region. Diagnostic hypotheses are guided by the type of demineralization and the presence of lytic, mixed, or densifying areas. Lastly, the aspect and location of fractures and association with other bone abnormalities refine the diagnosis.

Sacroiliac joint MRI for diagnosis of ax-SpA: algorithm to improve the specificity of the current ASAS MRI criteria.

OBJECTIVE: To compare sacroiliac joint (SIJ) lesions on MRI in women with versus without axial spondyloarthritis (ax-SpA) and establish an algorithm to determine whether such lesions are due to ax-SpA. METHODS: This retrospective comparative study assessed bone marrow edema (BME), sclerosis, erosions, osteophytes, and ankylosis at the SIJ in two groups of women, one with and another without ax-SpA. Sensitivity and specificity were calculated for combinations/characteristics of lesions, using rheumatologists' assessment with assessment of spondyloarthritis international society (ASAS) criteria as the gold standard for diagnosis of ax-SpA. RESULTS: Compared to women without ax-SpA, women with ax-SpA had more BME (61% vs 17%, p < 0.001), sclerosis (40% vs 22%, p < 0.001), erosions (35% vs 5%, p < 0.001), and ankylosis (2% vs 0%, p = 0.007), but less osteophytes (5% vs 33%, p < 0.001). The ASAS MRI criteria yielded 59% sensitivity and 88% specificity, while a new algorithm achieved 56% sensitivity and 95% specificity using the following criteria: no osteophytes at the SIJ and either (i) BME at the SIJ with at least one dimension ≥ 8 mm or (ii) at least one erosion at the SIJ. CONCLUSIONS: We recommend the following pragmatic algorithm for MRI diagnosis of ax-SpA in women: no osteophytes at the SIJ and either (i) BME at the SIJ with at least one dimension ≥ 8 mm or (ii) at least one erosion at the SIJ. The false positive rate when using the new algorithm (3.3%) is less than half than when using the ASAS MRI criteria (7.7%); thus, its application in clinical practice could reduce overdiagnosis and prevent overtreatment of ax-SpA. CLINICAL RELEVANCE STATEMENT: The developed algorithm has a false-positive rate that is less than half than when using the ASAS MRI criteria (3.3% vs 7.7%), thus its application in clinical practice could reduce overdiagnosis and prevent overtreatment of axial spondyloarthritis. KEY POINTS: • Compared to women without axial spondyloarthritis (ax-SpA), women with ax-SpA had a significantly higher prevalence of bone marrow edema (BME), sclerosis, erosions, and ankylosis, but a significantly lower prevalence of osteophytes. • A new algorithm for positive ax-SpA based on sacroiliac joint MRI was developed: no osteophytes at the sacroiliac joint (SIJ) and either (i) BME at the SIJ with at least one dimension ≥ 8 mm or (ii) at least one erosion at the SIJ. • We recommend this new algorithm for diagnosis of ax-SpA in women, as it has a significantly better specificity than the assessment of spondyloarthritis international society (ASAS) MRI criteria and less than half the false positive rate; thus, its application in clinical practice could reduce overdiagnosis and prevent overtreatment of ax-SpA.

Impact of the automatic tube current modulation (ATCM) system on virtual monoenergetic image quality for dual-source CT: A phantom study.

PURPOSE: To assess the impact of the automatic tube current modulation (ATCM) on virtual monoenergetic images (VMIs) quality in dual-source CT(DSCT). MATERIALS AND METHODS: Acquisitions were performed on DSCT using the Mercury phantom. The acquisition parameters for an abdomen-pelvic examination with single-energy CT(SECT) and dual-energy CT(DECT) imaging were used. Acquisitions were performed for each imaging mode using fixed mAs and ATCM. The mAs value was set to obtain a volume CT dose index of 11 mGy in fixed mAs acquisitions. This value was used as the reference mAs in ATCM acquisitions. The noise power spectrum and task-based transfer function at 40,50,60 and 70 keV levels were computed on VMIs and SECT images. The detectability index (d') was calculated for a lesion with an iodine concentration of 10 mg/mL. RESULTS: The noise magnitude on VMIs was higher with the ATCM system than with fixed mAs for all energy levels and section diameters of 21,26 and 31 cm. The noise texture and spatial resolution were similar between the fixed mAs and ATCM acquisitions for both imaging modes. The d' values were lower for all energy levels with ATCM than with fixed mAs acquisitions for 21 and 26 cm diameters by -39.82 ± 9.32%, similar at 31 cm diameter -4.13 ± 0.24% and higher at 36 cm diameter 10.40 ± 6.69%. It was higher on VMIs at all energy levels compared to SECT images. CONCLUSIONS: The ATCM system could be used with DECT imaging to optimize patient exposure without changing the noise texture and spatial resolution of VMIs compared to fixed mAs and SECT.