ABSTRACT
Durability of high-energy throughput batteries is a prerequisite for electric vehicles to penetrate the market. Despite remarkable progresses in silicon anodes with high energy densities, rapid capacity fading of full cells with silicon-graphite anodes limits their use. In this work, we unveil degradation mechanisms such as Li+ crosstalk between silicon and graphite, consequent Li+ accumulation in silicon, and capacity depression of graphite due to silicon expansion. The active material properties, i.e. silicon particle size and graphite hardness, are then modified based on these results to reduce Li+ accumulation in silicon and the subsequent degradation of the active materials in the anode. Finally, the cycling performance is tailored by designing electrodes to regulate Li+ crosstalk. The resultant full cell with an areal capacity of 6 mAh cm-2 has a cycle life of >750 cycles the volumetric energy density of 800 Wh L-1 in a commercial cell format.
ABSTRACT
PURPOSE: Lateral meniscus allograft transplantation (LMAT) is a feasible surgical option for young meniscus-deficient patients. Although several studies have explored the factors that contribute to graft extrusion, they have not been fully elucidated. The aim of this study was to determine the various factors that contribute to graft extrusion. METHODS: Patients with knees that had received LMAT using a keyhole technique (n = 87 knees in 82 patients) were reviewed. The median age of these patients was 22 years (range 19-54 years), and the median postprocedural follow-up interval was 5 days (range 1-136 days). Twelve magnetic resonance imaging (MRI) measurement parameters (axial and coronal location of the bone block) that could potentially influence graft extrusion were evaluated, along with absolute graft extrusion and relative percentage of extrusion (RPE). RESULTS: A significant correlation was found between 8 of the 12 MRI measurement parameters and both the absolute extrusion and RPE (r = 0.241-0.438, p < 0.05). The absolute middle distance and depth of the bone block were independent predictors of the absolute extrusion (ß = 0.30 and 0.15, respectively; p < 0.05), and the relative middle distance and relative bone-block elevation were found to be predictors of RPE (ß = 2.29 and 1.44, respectively; p < 0.05). CONCLUSION: The rate of graft extrusions after LMAT was high in this study. Both the coronal and axial locations of the bone block were found to influence graft extrusion in LMAT. Therefore, correct positioning of the bone block, including in both the axial and coronal planes, is essential to minimize graft extrusion. Future studies need to investigate the long-term clinical outcome and longevity of extruded menisci after transplantation. LEVEL OF EVIDENCE: Therapeutic case series, Level IV.
Subject(s)
Cartilage Diseases/surgery , Fibrocartilage/transplantation , Foreign-Body Migration/diagnostic imaging , Knee Joint/diagnostic imaging , Menisci, Tibial/surgery , Postoperative Complications/diagnostic imaging , Adult , Allografts , Female , Humans , Magnetic Resonance Imaging , Male , Middle Aged , Retrospective Studies , Transplantation, Homologous , Young AdultABSTRACT
The real time detection of quantitative oxygen release from the cathode is performed by in-situ Gas Chromatography as a tool to not only determine the amount of oxygen release from a lithium-ion cell but also to address the safety concerns. This in-situ gas chromatography technique monitoring the gas evolution during electrochemical reaction presents opportunities to clearly understand the effect of surface modification and predict on the cathode stability. The oxide cathode, 0.5Li2MnO3â0.5LiNi0.4Co0.2Mn0.4O2, surface modified by amorphous cobalt-phosphate nanoparticles (a-CoPO4) is prepared by a simple co-precipitation reaction followed by a mild heat treatment. The presence of a 40 nm thick a-CoPO4 coating layer wrapping the oxide powders is confirmed by electron microscopy. The electrochemical measurements reveal that the a-CoPO4 coated overlithiated layered oxide cathode shows better performances than the pristine counterpart. The enhanced performance of the surface modified oxide is attributed to the uniformly coated Co-P-O layer facilitating the suppression of O2 evolution and offering potential lithium host sites. Further, the formation of a stable SEI layer protecting electrolyte decomposition also contributes to enhanced stabilities with lesser voltage decay. The in-situ gas chromatography technique to study electrode safety offers opportunities to investigate the safety issues of a variety of nanostructured electrodes.
ABSTRACT
Mo doped Li excess transition metal oxides formulated as 0.3Li[Li(0.33)Mn(0.67)]O(2)·0.7Li[Ni(0.5-x)Co(0.2)Mn(0.3-x)Mo(2x)]O(2) were synthesized using the co-precipitation process. The effects of the substitution of Ni and Mn with Mo were investigated for the density of the states, the structure, cycling stability, rate performance and thermal stability by tools such as first principle calculations, synchrotron X-ray diffraction, field-emission SEM, solid state (7)Li MAS nuclear magnetic resonance (NMR), X-ray photoelectron spectroscopy (XPS), elemental mapping by scanning TEM (STEM), inductively coupled plasma atomic emission spectrometry (ICP-AES) and a differential scanning calorimeter (DSC). It was confirmed that high valence Mo(6+) doping of the Li-excess manganese-nickel-cobalt layered oxide in the transition metal enhanced the structural stability and electrochemical performance. This increase was due to strong Mo-O hybridization inducing weak Ni-O hybridization, which may reduce O(2) evolution, and metallic behavior resulting in a diminishing cell resistance.