RESUMEN
Adv. Mater. 2018, 30, 1705796 https://doi.org/10.1002/adma.201705796 The above article, published online on January 15, 2018, in Wiley Online Library (https://doi.org/10.1002/adma.201705796), has been retracted by agreement between the authors, the journal Editor in Chief Jos Lenders, and Wiley-VCH GmbH. The retraction has been agreed on following concerns raised by a third party and a subsequent investigation at Wake Forest University. Data integrity issues were found in Figures 1a, S2b, and S17. As a result, the authors consider the conclusions of this article invalid.
RESUMEN
Adv. Mater. 2019, 31, 1900813. https://doi.org/10.1002/adma.201900813 The above article, published online on May 6, 2019, in Wiley Online Library (https://doi.org/10.1002/adma.201900813), has been retracted by agreement between the authors, the journal Editor in Chief Jos Lenders, and Wiley-VCH GmbH. The retraction has been agreed on following concerns raised by a third party and a subsequent investigation at Wake Forest University. Data integrity issues were found in Figures 2c, 4d, S13a, S13b, S15, and S37. As a result, the authors consider the conclusions of this article invalid.
RESUMEN
Correction for 'Synthesis of lead-free Cs3Sb2Br9 perovskite alternative nanocrystals with enhanced photocatalytic CO2 reduction activity' by Chang Lu et al., Nanoscale, 2020, 12, 2987-2991, https://doi.org/10.1039/C9NR07722G.
RESUMEN
Catalysts based on Cu nanocrystals (NCs) for electrochemical CO2 -to-C2+ conversion with high activity have been a subject of considerable interest, but poor stability and low selectivity for a single C2+ product remain obstacles for realizing sustainable carbon-neutral cycles. Here, we used the facet-selective atomic layer deposition (FS-ALD) technique to selectively cover the (111) surface of Cu NCs with ultrathin Al2 O3 to increase the exposed facet ratio of (100)/(111), resulting in a faradaic efficiency ratio of C2 H4 /CH4 for overcoated Cu NCs 22 times higher than that for pure Cu NCs. Peak performance of the overcoated catalyst (Cu NCs/Al2 O3 -10C) reaches a C2 H4 faradaic efficiency of 60.4 % at a current density of 300â mA cm-2 in 5â M KOH electrolyte, when using a gas diffusion electrode flow cell. Moreover, the Al2 O3 overcoating effectively suppresses the dynamic mobility and the aggregation of Cu NCs, which explains the negligible activity loss and selectivity degradations of Cu NCs/Al2 O3 -10C shown in stability tests.
RESUMEN
Despite progress in small scale electrocatalytic production of hydrogen peroxide (H2O2) using a rotating ring-disk electrode, further work is needed to develop a non-toxic, selective, and stable O2-to-H2O2 electrocatalyst for realizing continuous on-site production of neutral hydrogen peroxide. We report ultrasmall and monodisperse colloidal PtP2 nanocrystals that achieve H2O2 production at near zero-overpotential with near unity H2O2 selectivity at 0.27 V vs. RHE. Density functional theory calculations indicate that P promotes hydrogenation of OOH* to H2O2 by weakening the Pt-OOH* bond and suppressing the dissociative OOH* to O* pathway. Atomic layer deposition of Al2O3 prevents NC aggregation and enables application in a polymer electrolyte membrane fuel cell (PEMFC) with a maximum r(H2O2) of 2.26 mmol h-1 cm-2 and a current efficiency of 78.8% even at a high current density of 150 mA cm-2. Catalyst stability enables an accumulated neutral H2O2 concentration in 600 mL of 3.0 wt% (pH = 6.6).
RESUMEN
A synthetic method for uniform and pure Cs3Sb2Br9 NCs has been developed. Cs3Sb2Br9 NCs exhibit a 10-fold increase in activity for the photocatalytic CO2 reduction reaction compared to CsPbBr3 NCs, achieving 510 µmol CO g-1 cat. after 4 h. Density functional theory shows that Cs3Sb2Br9 surfaces sufficiently expose Sb to allow reactivity, as opposed to the unreactive CsPbBr3 surface.
RESUMEN
Production of syngas with tunable CO/H2 ratio from renewable resources is an ideal way to provide a carbon-neutral feedstock for liquid fuel production. Ag is a benchmark electrocatalysts for CO2-to-CO conversion but high overpotential limits the efficiency. We synthesize AgP2 nanocrystals (NCs) with a greater than 3-fold reduction in overpotential for electrochemical CO2-to-CO reduction compared to Ag and greatly enhanced stability. Density functional theory calculations reveal a significant energy barrier decrease in the formate intermediate formation step. In situ X-ray absorption spectroscopy (XAS) shows that a maximum Faradaic efficiency is achieved at an average silver valence state of +1.08 in AgP2 NCs. A photocathode consisting of a n+p-Si wafer coated with ultrathin Al2O3 and AgP2 NCs achieves an onset potential of 0.2 V vs. RHE for CO production and a partial photocurrent density for CO at -0.11 V vs. RHE (j-0.11, CO) of -3.2 mA cm-2.
RESUMEN
One of the simplest molecular-scale electronic devices is the molecular rectifier. In spite of considerable efforts aimed at understanding structure-property relationships in these systems, devices with predictable and stable electronic properties are yet to be developed. Here, we demonstrate highly efficient current rectification in a new class of compounds that form self-assembled monolayers on silicon. We achieve this by exploiting the coupling of the molecules with the top electrode which, in turn, controls the position of the relevant molecular orbitals. The molecules consist of a silane anchoring group and a nitrogen-substituted benzene ring, separated by a propyl group and imine linkage, and result from a simple, robust, and high-yield synthetic procedure. We find that when incorporated in molecular diodes, these compounds can rectify current by as much as 3 orders of magnitude, depending on their structure, with a maximum rectification ratio of 2635 being obtained in ( E)-1-(4-cyanophenyl)- N-(3-(triethoxysilyl) propyl)methanimine (average Ravg = 1683 ± 458, at an applied voltage of 2 V). This performance is on par with that of the best molecular rectifiers obtained on metallic electrodes, but it has the advantage of lower cost and more efficient integration with current silicon technologies. The development of molecular rectifiers on silicon may yield hybrid systems that can expand the use of silicon toward novel functionalities governed by the molecular species grafted onto its surface.
RESUMEN
Developing earth-abundant and efficient electrocatalysts for photoelectrochemical water splitting is critical to realizing a high-performance solar-to-hydrogen energy conversion process. Herein, phosphorus-rich colloidal cobalt diphosphide nanocrystals (CoP2 NCs) are synthesized via hot injection. The CoP2 NCs show a Pt-like hydrogen evolution reaction (HER) electrocatalytic activity in acidic solution with a small overpotential of 39 mV to achieve -10 mA cm-2 and a very low Tafel slope of 32 mV dec-1 . Density functional theory (DFT) calculations reveal that the high P content both physically separates Co atoms to prevent H from over binding to multiple Co atoms, while simultaneously stabilizing H adsorbed to single Co atoms. The catalytic performance of the CoP2 NCs is further demonstrated in a metal-insulator-semiconductor photoelectrochemical device consisting of bottom p-Si light absorber, atomic layer deposition Al-ZnO passivation layers, and the CoP2 cocatalyst. The p-Si/AZO/TiO2 /CoP2 photocathode shows a photocurrent density of -16.7 mA cm-2 at 0 V versus reversible hydrogen electrode (RHE) and an output photovoltage of 0.54 V. The high performance and stability are attributed to the junction between p-Si and AZO, the corrosion-resistance of the pinhole-free TiO2 protective layer, and the fast HER kinetics of the CoP2 NCs.
RESUMEN
Colloidal semiconductor quantum dot (CQD)-based photocathodes for solar-driven hydrogen evolution have attracted significant attention because of their tunable size, nanostructured morphology, crystalline orientation, and band gap. Here, we report a thin film heterojunction photocathode composed of organic PEDOT:PSS as a hole transport layer, CdSe CQDs as a semiconductor light absorber, and conformal Pt layer deposited by atomic layer deposition (ALD) serving as both a passivation layer and cocatalyst for hydrogen evolution. In neutral aqueous solution, a PEDOT:PSS/CdSe/Pt heterogeneous photocathode with 200 cycles of ALD Pt produces a photocurrent density of -1.08 mA/cm2 (AM-1.5G, 100 mW/cm2) at a potential of 0 V versus reversible hydrogen electrode (RHE) ( j0) in neutral aqueous solution, which is nearly 12 times that of the pristine CdSe photocathode. This composite photocathode shows an onset potential for water reduction at +0.46 V versus RHE and long-term stability with negligible degradation. In the acidic electrolyte (pH = 1), where the hydrogen evolution reaction is more favorable but stability is limited because of photocorrosion, a thicker Pt film (300 cycles) is shown to greatly improve the device stability and a j0 of -2.14 mA/cm2 is obtained with only 8.3% activity degradation after 6 h, compared with 80% degradation under the same conditions when the less conformal electrodeposition method is used to deposit the Pt layer. Electrochemical impedance spectroscopy and time-resolved photoluminescence results indicate that these enhancements stem from a lower bulk charge recombination rate, higher interfacial charge-transfer rate, and faster reaction kinetics. We believe that these interface engineering strategies can be extended to other colloidal semiconductors to construct more efficient and stable heterogeneous photoelectrodes for solar fuel production.
RESUMEN
Highly efficient and stable electrocatalysts, particularly those that are capable of multifunctionality in the same electrolyte, are in high demand for the hydrogen evolution reaction (HER), oxygen evolution reaction (OER), and oxygen reduction reaction (ORR). In this work, highly monodisperse CoP and Co2 P nanocrystals (NCs) are synthesized using a robust solution-phase method. The highly exposed (211) crystal plane and abundant surface phosphide atoms make the CoP NCs efficient catalysts toward ORR and HER, while metal-rich Co2 P NCs show higher OER performance owing to easier formation of plentiful Co2 P@COOH heterojunctions. Density functional theory calculation results indicate that the desorption of OH* from cobalt sites is the rate-limiting step for both CoP and Co2 P in ORR and that the high content of phosphide can lower the reaction barrier. A water electrolyzer constructed with a CoP NC cathode and a Co2 P NC anode can achieve a current density of 10 mA cm-2 at 1.56 V, comparable even to the noble metal-based Pt/C and RuO2 /C pair. Furthermore, the CoP NCs are employed as an air cathode in a primary zinc-air battery, exhibiting a high power density of 62 mW cm-2 and good stability.
RESUMEN
Solution-grown films of CsPbBr3 nanocrystals imbedded in Cs4 PbBr6 are incorporated as the recombination layer in light-emitting diode (LED) structures. The kinetics at high carrier density of pure (extended) CsPbBr3 and the nanoinclusion composite are measured and analyzed, indicating second-order kinetics in extended and mainly first-order kinetics in the confined CsPbBr3 , respectively. Analysis of absorption strength of this all-perovskite, all-inorganic imbedded nanocrystal composite relative to pure CsPbBr3 indicates enhanced oscillator strength consistent with earlier published attribution of the sub-nanosecond exciton radiative lifetime in nanoprecipitates of CsPbBr3 in melt-grown CsBr host crystals and CsPbBr3 evaporated films.
RESUMEN
The crystal structure of thin films grown by atomic layer deposition (ALD) will determine important performance properties such as conductivity, breakdown voltage, and catalytic activity. We report the design of an atomic layer deposition chamber for in situ x-ray analysis that can be used to monitor changes to the crystal structural during ALD. The application of the chamber is demonstrated for Pt ALD on amorphous SiO2 and SrTiO3 (001) using synchrotron-based high resolution x-ray diffraction, grazing incidence x-ray diffraction, and grazing incidence small angle scattering.
RESUMEN
The mechanism of platinum atomic layer deposition using (methylcyclopentadienyl)trimethylplatinum and oxygen is investigated with in vacuo photoemission spectroscopy at the Stanford Synchrotron Radiation Lightsource. With this surface-sensitive technique, the surface species following the Pt precursor half cycle and the oxygen counter-reactant half cycle can be directly measured. We observed significant amounts of carbonaceous species following the Pt precursor pulse, consistent with dehydrogenation of the precursor ligands. Significantly more carbon is observed when deposition is carried out in the thermal decomposition temperature region. The carbonaceous layer is removed during the oxygen counter reactant pulse, and the photoemission spectrum shows that a layer of adsorbed oxygen remains on the surface as previously predicted.
RESUMEN
A colloidal quantum dot (QD) luminescent down-shifting (LDS) layer is used to sensitize an InGaAs short wavelength infrared photodetector to the near UV spectral band. An average improvement in the external quantum efficiency (EQE) from 1.8% to 21% across the near UV is realized using an LDS layer consisting of PbS/CdS core/shell QDs embedded in PMMA. A simple model is used to fit the experimental EQE data. A UV sensitive InGaAs imaging array is demonstrated and the effect of the LDS layer on the optical resolution is calculated. The bandwidth of the LDS detector under UV illumination is characterized and shown to be determined by the photoluminescence lifetime of the QDs.
RESUMEN
This article presents a perspective on the experimental and theoretical work to date on the efficiency of carrier multiplication (CM) in colloidal semiconductor nanocrystals (NCs). Early reports on CM in NCs suggested large CM efficiency enhancements. However, recent experiments have shown that CM in nanocrystalline samples is not significantly stronger, and often is weaker, than in the parent bulk when compared on an absolute photon energy basis. This finding is supported by theoretical consideration of the CM process and the competing intraband relaxation. We discuss the experimental artifacts that may have led to the apparently strong CM estimated in early reports. The finding of bulklike CM in NCs suggests that the main promise of quantum confinement is to boost the photovoltage at which carriers can be extracted. With this in mind, we discuss research directions that may result in effective use of CM in a solar cell.
RESUMEN
Nanocrystal (NC) films have been proposed as an alternative to bulk semiconductors for electronic applications such as solar cells and photodetectors. One outstanding challenge in NC electronics is to robustly control the carrier type to create stable p-n homojunction-based devices. We demonstrate that the postsynthetic addition of Cd to InAs nanocrystals switches the resulting InAs:Cd NC films from n-type to p-type when operating in a field effect transistor. This method presents a stable, facile way to control the carrier type of InAs nanocrystals prior to deposition. We present two mechanisms to explain the observed switch in carrier type. In mechanism 1, Cd atoms are incorporated at In sites in the lattice and act as acceptor defects, forming a partially compensated p-type semiconductor. In mechanism 2, Cd atoms passivate donor-type InAs surface states and create acceptor-type surface states. This work represents a critical step toward the creation of p-n homojunction-based NC electronics.
Asunto(s)
Fulerenos/química , Rayos Infrarrojos , Puntos Cuánticos , Electrones , Plomo/química , Semiconductores , Sulfuros/química , Factores de TiempoRESUMEN
We fabricate PbS colloidal quantum dot (QD)-based solar cells using a fullerene derivative as the electron-transporting layer (ETL). A thiol treatment and oxidation process are used to modify the morphology and electronic structure of the QD films, resulting in devices that exhibit a fill factor (FF) as high as 62%. We also show that, for QDs with a band gap of less than 1 eV, an open-circuit voltage (VOC) of 0.47 V can be achieved. The power conversion efficiency reaches 1.3% under 1 sun AM1.5 test conditions and 2.4% under monochromatic infrared (lambda=1310 nm) illumination. A consistent mechanism for device operation is developed through a circuit model and experimental measurements, shedding light on new approaches for optimization of solar cell performance by modifying the interface between the QDs and the neighboring charge transport layers.