Qualitative screening for adulterants in weight-loss supplements by ion mobility spectrometry.

Ion mobility spectrometry (IMS) served as a rapid, qualitative screening tool for the analysis of adulterated weight-loss products. We have previously shown that sibutramine extracted into methanol from dietary supplements can be detected at low levels (2ng) using a portable IMS spectrometer, and have adapted a similar method for the analysis of additional weight-loss product adulterants. An FDA collaborative study helped to define the limits for fluoxetine with a limit of detection of 2ng. We also evaluated more readily available, less toxic extraction solvents and found isopropanol and water were comparable to methanol. Isopropanol was favored over water for two reasons: (1) water increases the analysis time and (2) aqueous solutions were more susceptible to pH change, which affected the detection of sibutramine. In addition to sibutamine and fluoxetine, we surveyed 11 weight-loss adulterants; bumetanide, fenfluramine, furosemide, orlistat, phenolphthalein, phentermine, phenytoin, rimonabant, sertraline and two sibutramine analogs, desmethylsibutramine and didesmethylsibutramine, using portable and benchtop ion mobility spectrometers. Out of these 13 active pharmaceutical ingredients (APIs), portable and benchtop ion mobility spectrometers were capable of screening products for 10 of these APIs. The developed procedure was applied to two weight-loss dietary supplements using both portable and benchtop instruments. One product contained didesmethylsibutramine while the other contained didesmethylsibutramine and phenolphthalein.

Determination of levamisole in urine by gas chromatography-mass spectrometry.

The United States Public Health Service Substance Abuse and Mental Health Services Administration is alerting medical professionals that a substantial percentage of cocaine imported into the United States is adulterated with levamisole, a veterinary pharmaceutical that can cause blood cell disorders such as severe neutropenia and agranulocytosis. Levamisole HCl is the active ingredient in a number of veterinary drugs approved to treat worm infestations in animals. Levamisole HCl was also the active ingredient in a human drug for oral administration approved on June 18, 1990, as adjuvant treatment in combination with fluorouracil after surgical resection in patients with Duke's stage C colon cancer. This drug was withdrawn from the U.S. market around 2000, and it has not been marketed in the U.S. since then. The objective of this study was to develop a method to determine the amount of levamisole in urine samples. The procedure will be provided to state health laboratories as needed to be used in the evaluation of patients that have developed neutropenia or agranulocytosis in the setting of recent cocaine use. A gas chromatography-mass spectrometry method was validated and tested at two different laboratories, and the method limit of detection for levamisole is 1 ng/mL in urine when using a 5-mL sample. Confirmation of the stereoisomer of levamisole was done by high-performance liquid chromatography using a chiral column.

Standardization of Raman spectra for transfer of spectral libraries across different instruments.

In this paper we evaluate methods for standardization of Raman spectra that are required to improve spectral correlation computations between spectra measured on different instruments. Five commercially-available 785 nm Raman spectrometers from different vendors were included in the study. These spectrometers have diverse specifications and performance levels and range in size from laboratory-based instruments to field-deployable portable and handheld platforms. Since each Raman spectrometer has different characteristics, spectra obtained on one instrument cannot readily be compared to a library acquired on a different instrument without performing various types of spectral corrections (standardization). We outline a procedure that combines previously established Raman shift and intensity correction protocols with a resolution matching step to facilitate the comparison of a centralized master library with spectra acquired on different geographically distributed Raman spectrometers. The standardization procedure is effective in reducing the inherent instrument-to-instrument variability so that spectra from different spectrometers can be compared and reliable results obtained using library-based spectral correlation methods. The findings have important implications for the ability to transfer Raman spectral libraries between instruments.

Quantitative evaluation of the sensitivity of library-based Raman spectral correlation methods.

Library-based Raman spectral correlation methods are widely used in surveillance applications in multiple areas including the pharmaceutical industry, where Raman spectroscopy is commonly used in verification screening of incoming raw materials. While these spectral correlation methods are rapid and require little or no sample preparation, their sensitivity to the presence of contaminants has not been adequately evaluated. This is particularly important when dealing with pharmaceutical excipients, which are susceptible to economically motivated adulteration by substances having similar physical/chemical/spectroscopic properties. We report a novel approach to evaluating the sensitivity of library-based Raman spectral correlation methods to contaminants in binary systems using a hit-quality index model. We examine three excipient/contaminant systems, glycerin/diethylene glycol, propylene glycol/diethylene glycol, and lactose/melamine and find that the sensitivity to contaminant for each system is 18%, 32%, and 4%, respectively. These levels are well-correlated to the minimum contaminant composition that can be detected by both verification and identification methods. Our studies indicate that the most important factor that determines the sensitivity of a spectral correlation measurement to the presence of contaminant is the relative Raman scattering cross section of the contaminant.

Multivariate calibration and instrument standardization for the rapid detection of diethylene glycol in glycerin by Raman spectroscopy.

The transfer of a multivariate calibration model for quantitative determination of diethylene glycol (DEG) contaminant in pharmaceutical-grade glycerin between five portable Raman spectrometers was accomplished using piecewise direct standardization (PDS). The calibration set was developed using a multi-range ternary mixture design with successively reduced impurity concentration ranges. It was found that optimal selection of calibration transfer standards using the Kennard-Stone algorithm also required application of the algorithm to multiple successively reduced impurity concentration ranges. Partial least squares (PLS) calibration models were developed using the calibration set measured independently on each of the five spectrometers. The performance of the models was evaluated based on the root mean square error of prediction (RMSEP), calculated using independent validation samples. An F-test showed that no statistical differences in the variances were observed between models developed on different instruments. Direct cross-instrument prediction without standardization was performed between a single primary instrument and each of the four secondary instruments to evaluate the robustness of the primary instrument calibration model. Significant increases in the RMSEP values for the secondary instruments were observed due to instrument variability. Application of piecewise direct standardization using the optimal calibration transfer subset resulted in the lowest values of RMSEP for the secondary instruments. Using the optimal calibration transfer subset, an optimized calibration model was developed using a subset of the original calibration set, resulting in a DEG detection limit of 0.32% across all five instruments.

Using a portable ion mobility spectrometer to screen dietary supplements for sibutramine.

In response to recent incidents of undeclared sibutramine, an appetite suppressant found in dietary supplements, we developed a method to detect sibutramine using hand-held ion mobility spectrometers with an analysis time of 15 s. Ion mobility spectrometry is a high-throughput and sensitive technique that has been used for illicit drug, explosive, volatile organic compound and chemical warfare detection. We evaluated a hand-held ion mobility spectrometer as a tool for the analysis of supplement extracts containing sibutramine. The overall instrumental limit of detection of five portable ion mobility spectrometers was 2 ng of sibutramine HCl. When sample extractions containing 30 ng/µl or greater of sibutramine were analyzed, saturation of the ionization chamber of the spectrometer occurred and the instrument required more than three cleaning cycles to remove the drug. Hence, supplement samples suspected of containing sibutramine should be prepared at concentrations of 2-20 ng/µl. To obtain this target concentration range for products containing unknown amounts of sibutramine, we provided a simple sample preparation procedure, allowing the U.S. Food and Drug Administration or other agencies to screen products using the portable ion mobility spectrometer.

Characterization of currently marketed heparin products: key tests for quality assurance.

During the 2007-2008 heparin crisis, it was found that the United States Pharmacopeia (USP) testing monograph for unfractionated heparin sodium (UFH) did not detect the presence of the contaminant, oversulfated chondroitin sulfate (OSCS) in heparin. In response to this concern, new tests and specifications were developed by the Food and Drug Administration (FDA) and USP and put in place to not only detect the contaminant OSCS but also to improve assurance of quality and purity of the drug product. Additional tests were also developed to monitor the heparin supply chain for other possible economically motivated additives or impurities. In 2009, a new USP monograph was put in place that includes 500 MHz (1)H NMR, SAX-HPLC, %galactosamine in total hexosamine, and anticoagulation time assays with purified factor IIa or factor Xa. These tests represent orthogonal approaches for UFH identification, measurement of bioactivity, and for detection of process impurities or contaminants in UFH. The FDA has applied these analytical approaches to the study of UFH active pharmaceutical ingredients in the marketplace. Here, we describe results from a comprehensive survey of UFH collected from seven different sources after the 2009 monograph revision and compare these data with results obtained on other heparin samples collected during the 2007-2008 crisis.

Analysis of bead sizes for MR capsules labeled for sprinkle.

The bead sizes used in approved modified release capsules labeled for sprinkling on food was investigated to generate bead size guidelines for generic products labeled for sprinkling. The conclusions from a survey of FDA databases were corroborated with experimental data obtained by measuring the bead sizes of several reference-listed drugs on the market labeled for administration by sprinkling on food. The experimental data show that majority of the marketed products were found to have bead sizes of less than 1,500 microm (1.5 mm). Based on this information, a bead size of less than 1,500 microm should generally be considered acceptable for use in generic products labeled for sprinkling.

In vitro dissolution of oral modified-release tablets and capsules in ethanolic media.

In 2005, Palladone, an extended-release capsule, was withdrawn from the market after clinical testing showed subjects who took the product with alcohol had increased levels of drug in their blood. To better understand this phenomenon, we studied the in vitro drug release of 27 oral modified-release products in alcohol-containing media. In 40% alcoholic medium, 9 of 10 capsules and 2 of 17 tablets show accelerated drug release. When a high percentage of the total dose is released in a short period of time, the extended-release product is then performing like an immediate release formulation. Products were also tested in 5% and 20% alcoholic media and in simulated gastric fluid (without enzyme) containing 20% alcohol. No tested capsules or tablets exhibited a significant increase in drug release in media containing only 5% alcohol. The current study indicates that in vitro dissolution may provide evidence regarding the ruggedness of formulations to ingested alcohol.

Transdermal delivery of fentanyl from matrix and reservoir systems: effect of heat and compromised skin.

The United States Food and Drug Administration (FDA) has received numerous reports of serious adverse events, including death, in patients using fentanyl transdermal systems (FTS). To gain a better understanding of these problems, the current research focuses on the in vitro characterization of fentanyl reservoir (Duragesic) and matrix (Mylan) systems with respect to drug release and skin permeation under conditions of elevated temperature and compromised skin. In addition, different synthetic membrane barriers were evaluated to identify the one that best simulates fentanyl skin transport, and thus may be useful as a model for these systems in future studies. The results indicate that reservoir and matrix FTS are comparable when applied to intact skin at normal skin temperature but the kinetics of drug delivery are different in the two systems. At 40 degrees C, the permeation rate of fentanyl was twice that seen at 32 degrees C over the first 24 h in both systems; however, the total drug permeation in 72 h is significantly higher in the reservoir FTS. When applied to partially compromised skin, matrix FTS has a greater permeation enhancement effect than reservoir FTS. The intrinsic rate limiting membrane of the reservoir system served to limit drug permeation when the skin (barrier) permeability was compromised. Different ethylene vinyl acetate membranes were shown to have fentanyl permeability values encompassing the variability in human skin. Results using the in vitro model developed using synthetic membranes suggest that they mimic the effect of compromised skin on fentanyl permeability. Especially for highly potent drugs such as fentanyl, it is important that patients follow instructions regarding application of heat and use of the product on compromised skin.

Analysis of crude heparin by (1)H NMR, capillary electrophoresis, and strong-anion-exchange-HPLC for contamination by over sulfated chondroitin sulfate.

We previously published a strong-anion-exchange-high performance liquid chromatography (SAX-HPLC) method for the detection of the contaminant over sulfated chondroitin sulfate (OSCS) in heparin sodium active pharmaceutical ingredient (API). While APIs have been processed to remove impurities, crude heparins contain insoluble material, chondroitin sulfates, heparan sulfate, and proteins that may interfere with the recovery and measurement of OSCS. We examined 500MHz (1)H NMR, capillary electrophoresis (CE), and SAX-HPLC to quantify OSCS in crude heparin. Using our standard API protocol on OSCS spiked crude heparin samples; we observed a weight percent LOD and LOQ for the NMR approach of 0.1% and 0.3%, respectively, while the SAX-HPLC method gave values of 0.03% and 0.09%, respectively. CE data was not amenable to quantitative measurement of OSCS in crude heparin. We developed a modified HPLC sample preparation protocol using crude dissolved at the 100mg/mL level with a 2.5M NaCl solution. This SAX-HPLC approach gave a weight percent LOD of 0.02% and a LOQ of 0.07% and had better performance characteristics than that of the protocol used for APIs.

Generic omeprazole delayed-release capsules: in vitro performance evaluations.

BACKGROUND: After the patent on omeprazole delayed-release capsules expired, Food and Drug Administration (FDA) approved several generic omeprazole delayed-release capsule applications. FDA has received some complaints concerning a lack of therapeutic effect of the generic omeprazole delayed-release capsules. AIM: To investigate the quality of five different marketed generic omeprazole delayed-release capsules. METHOD: The dissolution characteristics of these generic omeprazole delayed-release capsules were determined according to the United States Pharmacopeia (USP). Additional dissolution studies under simulated in vivo physiological conditions were also conducted to determine whether generic omeprazole capsules would perform similarly under these conditions. RESULTS: The experimental data show that all the generic omeprazole delayed-release capsules met the USP standards. The in vitro dissolution of generic drugs is similar to that of the brand omeprazole product. CONCLUSIONS: There is no scientific evidence to support the claims that the generic omeprazole delayed-release capsules perform differently from the brand omeprazole product in vitro.

Reservoir based fentanyl transdermal drug delivery systems: effect of patch age on drug release and skin permeation.

PURPOSE: To understand and evaluate the stability and skin permeation profiles of fentanyl reservoir systems as a function of patch age. METHODS: Drug release and skin permeation studies were performed using a modified USP apparatus 5 with a novel sample preparation technique. RESULTS: The amount of fentanyl present in the EVA/adhesive layer (EAL) increased from about 17% of label claim (LC) at 5 months to 25% LC at 22 months. The increase in the drug concentration was mainly observed in the peripheral EAL. Simultaneously, the alcohol content of the patch decreased as a function of patch age. A significant effect of patch age on the drug content in the EAL and the drug release from the system was observed; however, skin permeation studies did not indicate an increase in drug delivery rate. CONCLUSIONS: Novel sample preparation technique with USP Apparatus 5 allowed determination of in vitro skin permeation rates for fentanyl transdermal patches with different designs. Permeation rates with cadaver skin as substrate were found not to change with patch age despite changing drug concentration in the EAL.

Screening of heparin API by near infrared reflectance and Raman spectroscopy.

Near infrared (NIR) reflectance and laser Raman spectra for a set of 69 heparin powder samples obtained from several foreign and domestic suppliers were measured. Both the NIR and Raman spectra of individual heparin API powder samples were correlated with sample compositions determined from response corrected relative peak areas of the capillary electropherograms of the samples using a partial least squares (PLS) regression model. Twenty-eight sample spectra were used to develop PLS models for the three major sample components; heparin, oversulfated chondroitin sulfate (OSCS) and glycosaminoglycans (GAGs). The PLS models were then used to successfully predict the compositions of 41 additional heparin samples. The success of these rapid, nondestructive technologies to identify contamination of heparin with OSCS demonstrates the potential of spectroscopy and chemometrics for screening of processed raw materials. These technologies are meant for screening purposes and not meant to replace either of the methods (capillary electrophoresis and NMR) currently required by USP and FDA.

Analysis of heparin sodium by SAX/HPLC for contaminants and impurities.

A chromatographic method was developed for the detection and quantification of the contaminant oversulfated chondroitin sulfate (OSCS) and the impurity dermatan sulfate in heparin active pharmaceutical ingredient (API). The HPLC analysis of heparin is carried out using a polymer-based strong anion exchange (SAX) column with gradient elution from 0.125 M sodium chloride to 2.5M sodium chloride buffered mobile phase. The limit of detection (LOD) and limit of quantitation (LOQ) for the contaminant OSCS in heparin were determined to be 0.03% and 0.1%, respectively. The LOD and LOQ for dermatan sulfate, an impurity in heparin sulfate, were determined to be 0.1% and 0.8%, respectively. This manuscript is not a policy document and is not intended to replace either of the methods (capillary electrophoresis and NMR) currently required by the FDA.

Lead in pharmaceutical products and dietary supplements.

The objective of this study is to determine lead concentrations in a variety of widely used pharmaceutical products, and to assess the risk of lead exposure from using these products. Lead concentrations of 45 products were measured with inductively-coupled plasma mass spectrometry. Six products had lead concentrations greater than 100 parts per billion (ppb), and the highest measured concentration was 500 ppb. The average mass of lead delivered to consumers by all products examined in this study when taken as directed was 0.22 micrograms per day, which is expected to increase the blood lead level of an adult by less than 1%. Five products were found to deliver more than 1 microg of lead per day when used as directed. Current tolerable lead limits in pharmaceutical substances vary widely, and in some cases exceed 10,000 ppb. The products examined in this study have lead concentrations far below these levels. However, in light of recent research demonstrating adverse effects in both children and adults from low level lead exposure, current lead limits for pharmaceutical substances are unacceptably high. Uniform lead limits that reflect current manufacturing capabilities are needed to insure the lowest achievable exposure to lead from these products.

Studies of variability in dissolution testing with USP apparatus 2.

In this study, gauge repeatability and reproducibility (gauge R&R) was used to analyze variability for USP apparatus 2 dissolution measurement systems. Experiments were designed to assess the variability due to apparatus, operator, and sample tablet. Since dissolution testing is a destructive test, a nested model was used for data analysis. Additionally, perturbation tests with both disintegrating and nondisintegrating tablets were performed to study the variability due to sample position within the dissolution vessel. For the gauge R&R study, two well-trained chemists used two mechanically calibrated USP apparatus 2 units. Six tests were performed by each operator on each apparatus. Evaluation of dissolution test results at 30 min using an internal DPA calibrator tablet NCDA#2 (10 mg prednisone) indicates that the main contribution to the total variance, approximately 70%, is due to the sample tablets, approximately 25% is from the apparatus and approximately 5% is due to the operators. There is no significant difference between operators and apparatuses as shown by the gauge R&R studies. In addition, dissolution results can be strongly affected by the position of the tablet within the vessel. Similarity (f1) and dissimilarity (f2) factors were calculated to statistically evaluate differences between perturbed and normal dissolution tests.

Quality assessment of internet pharmaceutical products using traditional and non-traditional analytical techniques.

This work investigated the use of non-traditional analytical methods to evaluate the quality of a variety of pharmaceutical products purchased via internet sites from foreign sources and compared the results with those obtained from conventional quality assurance methods. Traditional analytical techniques employing HPLC for potency, content uniformity, chromatographic purity and drug release profiles were used to evaluate the quality of five selected drug products (fluoxetine hydrochloride, levothyroxine sodium, metformin hydrochloride, phenytoin sodium, and warfarin sodium). Non-traditional techniques, such as near infrared spectroscopy (NIR), NIR imaging and thermogravimetric analysis (TGA), were employed to verify the results and investigate their potential as alternative testing methods. Two of 20 samples failed USP monographs for quality attributes. The additional analytical methods found 11 of 20 samples had different formulations when compared to the U.S. product. Seven of the 20 samples arrived in questionable containers, and 19 of 20 had incomplete labeling. Only 1 of the 20 samples had final packaging similar to the U.S. products. The non-traditional techniques complemented the traditional techniques used and highlighted additional quality issues for the products tested. For example, these methods detected suspect manufacturing issues (such as blending), which were not evident from traditional testing alone.