RESUMEN
Solid polymer electrolytes (SPEs) represent a pivotal advance toward high-energy solid-state lithium metal batteries. However, inadequate interfacial contact remains a significant bottleneck, impeding scalability and application. Inadequate interfacial contact remains a significant bottleneck, impeding scalability and application. Recent efforts have focused on transforming liquid/solid interfaces into solid/solid ones through in situ polymerization, which shows potential especially in reducing interface impedance. Here, we designed high-voltage SSLMBs with dual-reinforced stable interfaces by combining interface modification with an in situ polymerization technology inspired by targeted effects in medicine. Theoretical calculations and time-of-flight secondary ion mass spectrometry (TOF-SIMS) analysis demonstrate that tetramethylene sulfone (TMS) and bis(2,2,2-trifluoromethyl) carbonate (TFEC) exhibit selective adsorption at the interface of the LiNi0.8Co0.1Mn0.1O2 (NCM) cathode and Li anode, respectively. These compounds further decompose to form a stable cathode-electrolyte interface (CEI) film and a solid electrolyte interface (SEI) film, thereby simultaneously achieving a superior interface between the SPE and both the Li anode and NCM cathode. The developed Li||SPE||Li cell sustained cycling for more than 1000 h at 0.3 mA cm-2, and the NCM||SPE||Li cell also demonstrated an excellent capacity retention of 86.8% after 1000 cycles at 1 °C. This work will provide valuable insights for the rational design of high-voltage SSLMBs with stable interfaces, leveraging in situ polymerization as a cornerstone technology.
RESUMEN
Polymer matrix solid buoyancy materials (PSBMs) have the advantages of low density, high strength, low cost, and low water absorption, and they are widely used in marine engineering fields. How to improve the performance of PSBMs further and adapt them to harsh marine environments has become a hot topic in current research. This paper provides a comprehensive summary of PSBM, detailing both the preparation methodologies and properties of single-component and multi-component PSBM. In this paper, relevant research is systematically summarized from two dimensions of matrix and filler, and the application of thermosetting resin and thermoplastic resin as a matrix in PSBM is introduced in detail, and the corresponding research on fillers such as hollow glass microspheres, fly ash, hollow ceramic spheres and hollow polymer microspheres are expounded. This paper aims to summarize the latest advancements in PSBM research, thereby providing insights into the current state of the field and guiding future investigations.
RESUMEN
The irreversibility and low utilization of Zn anode stemming from the corrosion and dendrite growth have largely limited the commercialization of aqueous zinc batteries. Here, a carbonyl-rich polymer interphase of zinc polyacrylate (ZPAA) is spontaneously in-situ constructed on Zn anode to address the above-mentioned dilemmas. The ZPAA interlayer enables fast transport kinetics of Zn2+ and tailors the interfacial electric field for realizing the uniform Zn deposition due to superior zincophilicity, high Zn2+ transference number and inherent ion-diffusion channel. Importantly, acting as a buffer interphase with strong adhesion and isolation of electrolytes, this functional layer effectively protects the Zn electrode against the water-induced erosion and passivation. Remarkably, the ZPAA@Zn electrode realizes an enhanced Coulombic efficiency of 99.71 % within 2200 cycles, delivers an ultra-long cycling stability over 7660 h (>319 days, 1 mA cm-2) and 2460 h (5 mA cm-2) with lower voltage hysteresis. Also, the ZPAA@Zn/MnO2 full cell maintains a high capacity of 114 mAh/g after 2000 cycles, much better that of untreated Zn/MnO2 cell (25 mAh/g). This concept of in-situ fabricating ion-sieve-like polymer interphase provides a facile approach to stabilize Zn anode and further paves a way for high-performance aqueous batteries.
RESUMEN
Living organisms have developed a miraculous biomineralization strategy to form multistage organic-inorganic composites through the orderly assembly of hard/soft substances, achieving mechanical enhancement of materials from the nanoscale to the macroscale. Inspired by biominerals, this study used polydopamine (PDA) coating as a template to induce the growth of hydroxyapatite (HAP) on the surface of carbon fibers (CFs) for enhancing the interfacial properties of the CF/epoxy resin composites. This polydopamine-assisted hydroxyapatite formation (pHAF) biomimetic mineralization strategy constructs soft/hard ordered structure on the CF surface, which not only improves the chemical reaction activity of the CFs but also increases the fiber surface roughness. This, in turn, enhances the interaction and loading delivery among the fibers and the matrix. Compared to the untreated carbon fiber/epoxy resin (CF/EP) composites, the prepared composites showed a substantial enhancement in interlaminar shear strength (ILSS), flexural strength, and interfacial shear strength (IFSS), with improvements of 45.2 %, 46.9 %, and 60.5 %, respectively. This can be attributed to the HAP nanolayers increasing the adhesion and mechanical interlocking with the CFs to the matrix. This study provides an interface modification method of biomimetic mineralization for the preparation of high strength CF composites.
Asunto(s)
Fibra de Carbono , Durapatita , Indoles , Polímeros , Indoles/química , Durapatita/química , Polímeros/química , Fibra de Carbono/química , Materiales Biomiméticos/química , Biomimética/métodos , Fenómenos Mecánicos , Resistencia al Corte , Propiedades de Superficie , Resinas Epoxi/químicaRESUMEN
Parasitic side reactions and dendrite growth on zinc anodes are formidable issues causing limited lifetime of aqueous zinc ion batteries (ZIBs). Herein, a spontaneous cascade optimization strategy is first proposed to regulate Zn2+ migration-diffusion behavior. Specifically, PAPE@Zn layer with separation-reconstruction properties is constructed in situ on Zn anode. In this layer, well-soluble poly(ethylene oxide) (PEO) can spontaneously separation to bulk electrolyte and weaken the preferential coordination between H2O and Zn2+ to achieve primary optimization. Meanwhile, poor-soluble polymerized-4-acryloylmorpholine (PACMO) is reconstructed on Zn anode as hydrophobic flower-like arrays with abundant zincophilic sites, further guiding the de-solvation and homogeneous diffusion of Zn2+ to achieve the secondary optimization. Cascade optimization effectively regulates Zn2+ migration-diffusion behavior, dendrite growth and side reactions of Zn anode are negligible, and the stability is significantly improved. Consequently, symmetrical cells exhibit stability over 4000â h (1â mA cm-2). PAPE@Zn//NH4 +-V2O5 full cells with a high current density of 15â A g-1 maintains 72.2 % capacity retention for 12000â cycles. Even better, the full cell demonstrates excellent performance of cumulative capacity of 2.33â Ah cm-2 at ultra-low negative/positive (N/P) ratio of 0.6 and a high mass-loading (~17â mg cm-2). The spontaneous cascade optimization strategy provides novel path to achieve high-performance and practical ZIBs.
RESUMEN
The commercialization process of perovskite solar cells (PSCs) is markedly restricted by the power conversion efficiency (PCE) and long-term stability. During fabrication and operation, the bottom interface of the organic-inorganic hybrid perovskite layer frequently exhibits voids and residual PbI2, while these defects inevitably act as recombination centers and degradation sites, affecting the efficiency and stability of the devices. Therefore, the degradation and nonradiative recombination originating from the buried interface should be thoroughly resolved. Here, we report a multifunctional passivator by introducing malonic dihydrazide as an interfacial chemical bridge between the electron transport layer and the perovskite (PVK) layer. MADH with hydrazine groups improves the surface affinity of SnO2 and provides nucleation sites for the growth of PVK, leading to the reduced residual PbI2 and the voids resulting from the inhomogeneous solvent volatilization at the bottom interface. Meanwhile, the hydrazine group and carbonyl group synergistically coordinate with Pb2+ to improve the crystal growth environment, reducing the number of Pb-related defects. Eventually, the PCE of the PSCs is significantly enhanced benefiting from the reduced interfacial defects and the increased carrier transport. Moreover, the reductive nature of hydrazide further inhibits I2 generation during long-term operation, and the device retains 90% of the initial PCE under a 1 sun continuous illumination exposure of 700 h.
RESUMEN
Metal zinc (Zn) is being explored as a possible anode for aqueous zinc ion batteries (AZIBs). However, unrestrained Zn dendrite caused by "tip effect" and chemical corrosion continue to plague the Zn deposition process, limiting the functionality of AZIBs and prohibiting their use at high current densities. This work presents an in situ approach for introducing homogeneous ZnO nanoarrays onto the surface of Zn foil (Zn@ZnO NAs) as a functional protective interphase. On the one hand, well-distributed ZnO NAs protection layer can regulate the "tip effect" and confine the growth of Zn dendrite. On the other hand, the ZnO NAs layer can enhance the desolvation and diffusion process of Zn2+ on the surface of anode, attributing to low voltage hysteresis and exceptional electrochemical performance at high current densities. As a result, the Zn@ZnO NAs exhibits a low voltage hysteresis of 50.8 mV with a superb lifespan of 1200 h at a current density of 5 mA cm-2. Moreover, Zn@ZnO NAs||α-MnO2 full-cell shows a superior cycling performance after 500 cycles at 0.5 A g-1 with a capacity of 216.69 mAh g-1. This work is expected to provide ideas for designing other reversible zinc anode chemical systems, especially under a high current density.
RESUMEN
All-solid-state sodium metal batteries face the challenges of low ionic conductivity of solid electrolytes and poor wettability towards metallic Na anode. Herein, Na3Zr2Si2PO12 solid electrolyte is doped with Ca2+, obtaining a high ionic conductivity of 2.09×10-3â S cm-1 with low electronic conductivity of 1.43×10-8â S cm-1 at room temperature, which could accelerate Na+ transportation and suppress sodium dendrite growth. Meanwhile, a graphite-based interface layer is coated on Na3.4Zr1.8Ca0.2Si2PO12 (Na3.4Zr1.8Ca0.2Si2PO12-G) in order to improve the solid-solid contact between solid electrolyte and Na anode, realizing a uniform current distribution and smooth Na metal plating/stripping, and thus achieving a triple higher critical current density of 3.5â mA cm-2 compared with that of Na3.4Zr1.8Ca0.2Si2PO12. In addition, the assembled Na3V2(PO4)3/Na3.4Zr1.8Ca0.2Si2PO12-G/Na all-solid-state battery exhibits excellent electrochemical performances with a reversible capacity of 81.47â mAh g-1 at 1â C and capacity retention of 97.75 % after 500 cycles.
RESUMEN
With the increasing development of nanomaterials, the construction of multiscale nanostructured interphase has emerged as a viable technique to reinforce carbon fiber-reinforced polymer composites. Here, "flexible" aramid nanofibers (ANFs) were first introduced on the surface of carbon fibers (CF) by electrophoretic deposition (EPD), and then "rigid" MXene sheets were grafted by ultrasonic impregnation. This feasible two-step treatment introduces a hierarchical "rigid-flexible" structure at the CF/polyamide (PA) interface. Results showed that this "rigid-flexible" multilayer structure improved the roughness, chemical bonding, mechanical interlocking, and wettability of CF/PA composites. At the same time, the modulus variation between the fiber and the matrix is significantly smoothed due to the increased thickness of the interfacial layer, increasing the payload transfer from the PA matrix to the fiber and decreasing the stress concentration. Compared to the desized CF, the interlaminar shear strength (ILSS) and tensile strength of the modified CF-ANF@MX0.2/PA composite increased by 50.02 and 36.11%, respectively. This innovative interfacial design and feasible treatment method facilitate the construction of firmly interacting interfacial layers in CF/PA composites, offering broad prospects for the production of high-performance CF/PA composites.
RESUMEN
SnO2 layer between Li1.5Al0.5Ge1.5(PO4)3 (LAGP) and lithium anode was prepared through simple scratch-coating process to improve interface properties. The physical phase, morphology, and electrochemical properties of Li/SnO2/LAGP structure were characterized by X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, and electrochemical analytical methods. It was found that SnO2 layer effectively improved the interface stability of LAGP and lithium anode. The prepared Li/SnO2/LAGP/SnO2/Li symmetric cell exhibited a large critical current density of 1.8 mA cm-2 and demonstrated excellent cycling characteristics. The polarization voltages of symmetric cell were 0.1 V and 0.8 V after 1000 h of cycling at current densities of 0.04 mA cm-2 and 0.5 mA cm-2, respectively. Li/SnO2@LAGP/LiFePO4 solid-state full cells were also assembled, exhibiting a discharge specific capacity of 150 mAh g-1 after 200 cycles at 0.1C with capacity retention rate of 96 %. The good interface properties of Li/SnO2/LAGP structure are attributed to the transformation of SnO2 layer into a buffer layer containing Li2O, Sn0, and LixSny alloy during cycling process, which effectively inhibits the reduction reaction between LAGP and lithium anode.
RESUMEN
Achieving a highly robust zinc (Zn) metal anode is extremely important for improving the performance of aqueous Zn-ion batteries (AZIBs) for advancing "carbon neutrality" society, which is hampered by the uncontrollable growth of Zn dendrite and severe side reactions including hydrogen evolution reaction, corrosion, and passivation, etc. Herein, an interlayer containing fluorinated zincophilic covalent organic framework with sulfonic acid groups (COF-S-F) is developed on Zn metal (Zn@COF-S-F) as the artificial solid electrolyte interface (SEI). Sulfonic acid group (- SO3H) in COF-S-F can effectively ameliorate the desolvation process of hydrated Zn ions, and the three-dimensional channel with fluoride group (-F) can provide interconnected channels for the favorable transport of Zn ions with ion-confinement effects, endowing Zn@COF-S-F with dendrite-free morphology and suppressed side reactions. Consequently, Zn@COF-S-F symmetric cell can stably cycle for 1,000 h with low average hysteresis voltage (50.5 mV) at the current density of 1.5 mA cm-2. Zn@COF-S-F|MnO2 cell delivers the discharge specific capacity of 206.8 mAh g-1 at the current density of 1.2 A g-1 after 800 cycles with high-capacity retention (87.9%). Enlightening, building artificial SEI on metallic Zn surface with targeted design has been proved as the effective strategy to foster the practical application of high-performance AZIBs.
RESUMEN
Hole-transport-layer-free perovskite solar cells have attracted strong interest due to their simple structure and low cost, but charge recombination is serious. Built-in electric field engineering is an intrinsic driver to facilitate charge separation transport and improve the efficiency of photovoltaic devices. However, the enhancement of the built-in electric field strength is often accompanied by the narrowing of the space charge region, which becomes a key constraint to the performance improvement of the device. Here, we propose an effective regulation method, the component engineering of quantum dots, to enhance the strength of the built-in electric field and broaden the range of space charge. By using all inorganic CsPbBrxI3-x (x = 0, 1, 2, 3) quantum dot interface modification to passivate the defects of MAPbI3 perovskite films, the regulation law of quantum dot components on the work function of perovskite films was revealed, and the mechanism of their influence on the internal electric field intensity and space charge region distribution was further clarified, thereby fundamentally solving the serious problem of charge recombination. As directly observed by electron-beam-induced current (EBIC), the introduction of CsPbBr2I quantum dots can effectively enhance the interfacial electric field intensity, widening the space charge region from 160 to 430 nm. Moreover, the efficiency of the hole-free transport layer perovskite solar cells modified by CsPbBr2I quantum dots was also significantly enhanced by 1.5 times. This is an important guideline for electric field modulation and efficiency improvement within photovoltaic devices with other simplified structures.
RESUMEN
Modifying the surface of a catalyst with heteroatoms can regulate the interfacial atomic valence state and adjust the charge distribution, which is promising for obtaining desirable platinum carbon catalyst (Pt/C)-matched oxygen reduction reaction (ORR) catalytic performance. Here, we developed an efficient method to access O-rich crystalline interfacial-exposed palladium-tin alloy (111) crystal surfaces [Pd3Sn (111)] for highly efficient ORR via direct reduction of Pd/Sn metal salt species that are well dispersed in a nitrogen, phosphorus-doped carbonaceous (NPC) substrate. In addition to the other materials, preembedded Pd/Sn metal salt species in NPC control the release of metal sources upon reduction in the liquid phase, resulting in the grafting of an as-prepared PdSn alloy with many merits, such as efficient electron conduction, short-range crystallinity and increased crystal interface exposure. The presence of a considerable quantity of oxygen atoms at the interface of small-sized PdSn alloys on NPC substrates has been methodically verified by powder X-ray diffraction, high-resolution transmission electron microscopy and X-ray photoelectron spectroscopy characterizations. The PdSn-O sample exhibited excellent ORR activity, achieving an onset potential of â¼0.99 V and a half-wave potential of â¼0.88 V at 1600 rpm in O2-saturated 1.0 M KOH. Density functional theory simulations of pure Pd, Pd-O, the PdSn alloy and PdSn-O suggest that interfacial oxygen atom modification is responsible for the significantly improved ORR activity. The assembled zinc-air battery provides a high specific power of 218.9 mW cm-2 and a specific capacity of 810.6 mAh gZn-1. Our approach has the potential to stimulate the preparation of O-rich crystalline interfacial-exposed alloy compounds for other energy conversion applications.
RESUMEN
Solid-state batteries (SSBs) based on Li-rich Mn-based oxide (LRMO) cathodes attract much attention because of their high energy density as well as high safety. But their development was seriously hindered by the interfacial instability and inferior electrochemical performance. Herein, we design a three-dimensional foam-structured GaN-Li composite anode and successfully construct a high-performance SSB based on Co-free Li1.2 Ni0.2 Mn0.6 O2 cathode and Li6.5 La3 Zr1.5 Ta0.5 O12 (LLZTO) solid electrolyte. The interfacial resistance is considerably reduced to only 1.53â Ω cm2 and the assembled Li symmetric cell is stably cycled more than 10,000â h at 0.1-0.2â mA cm-2 . The full battery shows a high initial capacity of 245â mAh g-1 at 0.1â C and does not show any capacity degradation after 200â cycles at 0.2â C (≈100 %). The voltage decay is well suppressed and it is significantly decreased from 2.96â mV/cycle to only 0.66â mV/cycle. The SSB also shows a very high rate capability (≈170â mAh g-1 at 1â C) comparable to a liquid electrolyte-based battery. Moreover, the oxygen anion redox (OAR) reversibility of LRMO in SSB is much higher than that in liquid electrolyte-based cells. This study offers a distinct strategy for constructing high-performance LRMO-based SSBs and sheds light on the development and application of high-energy density SSBs.
RESUMEN
Molecular oxygen activation plays an important role in the electrocatalytic degradation of recalcitrant pollutants. And the key lies in the tailoring of electronic structures over catalysts. Herein, carbon nitride with K/O interfacial modification (KOCN) was designed and fabricated for efficient molecular oxygen activation. Theoretical screening results revealed the possible substitution of peripheral N atoms by O atoms and the location of K atoms in the six-fold cavities of g-C3N4 framework. Spectroscopic and experimental results reveal that the existence of K/O promotes charge redistribution over as-prepared catalysts, leading to optimized electronic structures. Therefore, optimized oxygen adsorption was realized over 8 % KOCN, which was further converted into superoxide and singlet oxygen effectively. The rate constant of 8 % KOCN (1.8 × 10-2 min-1) reached 2.2 folds of pristine g-C3N4 (8.1 × 10-3 min-1) counterpart during tetracycline degradation. Moreover, the high electron mobility and excellent structural stability endow the catalyst with remarkable catalytic performance in a broad pH range of 3-11.
RESUMEN
Tin-lead (Sn-Pb) mixed perovskites is beneficial to a single-junction or all-perovskite tandem device. However, the poor quality of the perovskite surface resulting from Sn2+ oxidation and uncontrollable crystallization degrades device performance and stability. Herein, based on interface engineering, a novel biguanide derivative of PZBGACl is employed that integrates different types of N-related groups to reconstruct the surface/grain boundaries of Sn-Pb perovskite. Combined with the microcorrosion effect of isopropanol solvent, PZBGACl can induce surface recrystallization of perovskite, and passivate various types of defects via hydrogen bond or Lewis acid-base interaction, leading to an excellent perovskite film with reduced stress, larger grain size, and more n-type surface. As a result, the obtained Sn-Pb solar cell achieves a power conversion efficiency of 22.0%, and exhibits excellent N2 storage/operation stability.
RESUMEN
The increasing demand for high-energy-density and high-safety energy storage devices has sparked a growing interest in all-solid-state lithium metal batteries (ASSLMBs). A high-quality inorganic solid-state electrolyte (ISE) is a fundamental requirement for ASSLMBs, and an effective ISE/Li interface is a key factor in attaining high-performance ASSLMBs. In this Concept, we initially summarize the challenges encountered by ISE/Li interfaces and delineate four commonly employed strategies for modifying the ISE/Li interface. Then, we explore the merits and drawbacks of coatings utilized as ISE/Li interfacial phases. We also delve into the commonly employed thermal bonding and innovative cold bonding methods utilized for inâ situ interface preparation. Lastly, we spotlight future directions for enhancing the functionality of ISE/Li interfaces and achieving high-performance ASSLMBs.
RESUMEN
BACKGROUND: Interface modification driven by supramolecular self-assembly has been accepted as a valuable strategy for emulsion stabilization enhancement. However, there has been a dearth of comparative research on the effect of simple complexation and assembly from the perspective of the responsible mechanism. RESULTS: The present study selected zein and tannic acid (TA) as representative protein and polyphenol modules for self-assembly (coined as TA-modified zein particle and TA-zein complex particle) to explore the surface properties and interfacial behavior, as well as the stability of constructed Pickering emulsions to obtain the regulation law of different modification methods on the interfacial behavior of colloidal particles. The results demonstrated that TA-modified zein colloidal particles potentially improved the emulsifying properties. When the TA concentration was 3 mmol L-1 , the optimized TA-modified zein particle was nano-sized (109.83 nm) and had advantageous interfacial properties, including sharply reduced surface hydrophobicity, as well as a low diffusion rate at the oil/water interface. As a result, the shelf life of Pickering emulsion containing 50% oil phase was extended to 90 days. CONCLUSION: Through multi-angled research on the properties of the interfacial membrane, improvement of emulsion stability was a result of the formation of viscoelastic interfacial film that resulted from the decrease of absorption rate between particles and interface. Using refined regulation to investigate the role of different sample preparation methods from a mechanistic perspective. Overall, the present study has provided a reference for TA to regulate the surface properties and interface behavior of zein colloidal particles, enriched the understanding of colloidal interface assembly, and provided a theoretical basis for the quality control of interface-oriented food systems. © 2023 Society of Chemical Industry.
Asunto(s)
Zeína , Emulsiones/química , Zeína/química , Tamaño de la Partícula , PolifenolesRESUMEN
Functional interfaces and devices for rapid adsorption and immobilization of nucleic acids (NAs) are significant for relevant bioengineering applications. Herein, a microdevice with poly(acrylic acid) (PAA) photosensitive resin was integrated by three-dimensional (3D) printing, named DPAA for short. Precise microscale structures and abundant surface carboxyl functional groups were fabricated for fast and high-throughput deoxyribonucleic acid (DNA) separation. Surface modification was then done using polydopamine (PDA) and poly(ethylene glycol) (PEG) to obtain modified poly(acrylic acid) (PAA)-based devices DPDA-PAA and DPEG-PAA rich in amino and hydroxyl groups, respectively. The fabricated device DPAA possessed superior printing accuracy (40-50 µm). Functionalization of amino and hydroxyl was successful, and the modified devices DPDA-PAA and DPEG-PAA maintained a high thermal stability like DPAA. Surface potential analysis and molecular dynamics simulation indicated that the affinity for DNA was in the order of DPDA-PAA > DPEG-PAA > DPAA. Further DNA separation experiments confirmed the high throughput and high selectivity of DNA separation performance, consistent with the predicted affinity results. DPDA-PAA showed relatively the highest DNA extraction yield, while DPEG-PAA was the worst. An acidic binding system is more favorable for DNA separation and recovery. DPDA-PAA showed significantly better DNA extraction performance than DPAA in a weakly acidic environment (pH 5.0-7.0), and the average DNA yield of the first elution was 2.16 times that of DPAA. This work validates the possibility of modification on integrated 3D microdevices to improve their DNA separation efficiency effectively. It also provides a new direction for the rational design and functionalization of bioengineering separators based on nonmagnetic methods. It may pave a new path for the highly efficient polymerase chain reaction diagnosis.
Asunto(s)
Ácidos Nucleicos , Polietilenglicoles , Polietilenglicoles/química , ADNRESUMEN
Ultrathin (â¼10 nm) insulating polymer films are commonly employed as an interfacial modification layer (IML) to improve charge balance and suppress interfacial exciton quenching in quantum dot light-emitting diodes (QLEDs). However, because the thickness is smaller than the energy transfer distance, interfacial exciton quenching is only partially suppressed, leading to the degrading of device performance. In this work, a thick (35 nm) inorganic CdS film is developed to serve as the IML of CdSe quantum-dot-based QLED. Benefiting from relatively low electron mobility and well-matched energy level, the CdS IML can effectively improve charge balance. In addition, because the thickness is larger than the energy transfer distance, interfacial exciton quenching can be completely blocked. As a result, the QLEDs with CdS IML exhibit a maximum EQE of 21.2% and a peak current efficiency of 24.2 cd A-1, which are about 1.32- and 1.4-fold higher than 16.1% and 17.3 cd A-1 of the devices without CdS IML, respectively. Our work offers an efficient method to completely block interfacial exciton quenching, which may open a new avenue for developing higher-performance QLEDs.