[Comparison of flow conditions of adhesives and retention force of restorations among four cement-retained methods of implant-supported fixed prostheses].

Objective: To compare the effect on the flow conditions of adhesives and the retention force of restorations among different cement-retained methods of implant-supported fixed prostheses. Methods: Four common cement-retained methods were selected, including the occlusal hole for screw access (OH), the lingual hole for adhesives overflow (LH), the resin replica for titanium abutment (RR), and the traditional cement-retained method (the control group). The adhesive used in this study was resin-modified glass ionomer cement. The two-dimensional analysis models of computational fluid dynamics (CFD) were established. The flow conditions of adhesives in the adhesion process was analyzed by the CFD analysis. The internal filling ratio and the amount of neck overflow of adhesives below the edge of the prosthesis were calculated. Ten zirconia prostheses in each group were processed and cemented. The retention force was examined by mechanical tensile experiments in vitro. Results: The CFD analysis showed the internal filling ratio of adhesives from high to low was the LH group, the OH group, the RR group and the control group. The amount of neck overflow of adhesives below the edge of the prosthesis from less to more was the RR group, the OH group, the LH group and the control group. The retention force was (240.7±33.9) N in the control group, (278.2±59.1) N in the OH group, (292.9±47.9) N in the LH group, and (262.8±59.4) N in the RR group. There was a statistically significant difference in the retention force between the LH group and the control group (P=0.029). There was no significant difference among the other groups (P>0.05). Conclusions: The modified cement-retained methods can effectively reduce the amount of neck overflow of adhesives, and improve the filling condition of adhesive in the adhesive clearance to ensure the retention force of the prostheses. Clinically, the appropriate modified cement-retained method should be selected according to the three-dimensional position of the implant and the position of prosthetic margin.

Biomechanical effects of morphological variations of the cortical wall at the bone-cement interface.

BACKGROUND: The integrity of bone-cement interface is very important for the stabilization and long-term sustain of cemented prosthesis. Variations in the bone-cement interface morphology may affect the mechanical response of the shape-closed interlock. METHODS: Self-developed new reamer was used to process fresh pig reamed femoral canal, creating cortical grooves in the canal wall of experimental group. The biomechanical effects of varying the morphology with grooves of the bone-cement interface were investigated using finite element analysis (FEA) and validated using companion experimental data. Micro-CT scans were used to document interlock morphology. RESULTS: The contact area of the bone-cement interface was greater (P < 0.05) for the experimental group (5470 ± 265 mm(2)) when compared to the specimens of control group (5289 ± 299 mm(2)). The mechanical responses to tensile loading and anti-torsion showed that the specimens with grooves were stronger (P < 0.05) at the bone-cement interface than the specimens without grooves. There were positively significant correlation between the contact area and the tensile force (r (2) = 0.85) and the maximal torsion (r (2) = 0.77) at the bone-cement interface. The volume of cement of the experimental group (7688 ± 278 mm(3)) was greater (P < 0.05) than of the control group (5764 ± 186 mm(3)). There were positively significant correlations between the volume of cement and the tensile force (r (2) = 0.90) and the maximal torsion (r (2) = 0.97) at the bone-cement interface. The FEA results compared favorably to the tensile and torsion relationships determined experimentally. More cracks occurred in the cement than in the bone. CONCLUSIONS: Converting the standard reaming process from a smooth bore cortical tube to the one with grooves permits the cement to interlock with the reamed bony wall. This would increase the strength of the bone-cement interface.

Evaluation of the bond strengths of 3 endodontic cements via push-out test.

In this study, the push-out method was used to evaluate the bond strengths of 3 types of endodontic cements according to their composite base: methacrylate, epoxy resin, and an experimental copaiba oil resin. The study hypothesis was that the methacrylate-based and experimental cements would have bond strengths equal to or greater than that of the epoxy resin-based cement. Thirty bovine tooth roots, 18 mm long, were divided into 3 groups (n = 10) based on the chosen cement treatment. After treatment, the specimens were sectioned and submitted to a push-out test. Results showed that there was no statistically significant difference (P < 0.05) between the cements used or between the middle and apical thirds of the roots. It could be concluded that the tested cements had satisfactory and similar bond strengths to dentin.

Recambio de polietileno mediante la cementación de un nuevo componente sobre el metal-back osteointegrado / Polyethylene replacement by cementing a new component over the osseointegrated metal-back

Objetivo. Ante una cirugía de revisión de artroplastia total de cadera no cementada por desgaste de polietileno está indicado mantener el cotilo metálico cuando se compruebe intraoperatoriamente su estabilidad, sustituyendo únicamente el polietileno que se cementa si el anclaje no es posible. El objetivo del presente estudio fue evaluar los resultados clínicos y radiográficos a medio plazo de la cementación de polietileno dentro de un componente acetabular metálico osteointegrado. Material y método. Se analizaron retrospectivamente 15 pacientes cuya indicación para la cirugía fue el desgaste de polietileno, con un periodo de seguimiento medio de 6,1 años (rango 3,5-9,7 años). El Harris Hip Score se utilizó para valorar los resultados clínicos antes de la intervención y al final del seguimiento. Se realizaron radiografías anteroposteriores y axiales de cadera para descartar complicaciones. Resultados. La puntuación media en el Harris Hip Score mejoró, pasando de los 64,7 puntos en el preoperatorio a los 80,3 al final del seguimiento. Las lesiones osteolíticas desaparecieron, o al menos no aumentaron de tamaño, en los controles radiográficos. Una paciente (6,7%) sufrió 2 episodios de luxación, que se trataron sin necesidad de cirugía. Otro paciente presentó aflojamiento aséptico del vástago femoral, que requirió el recambio. Conclusiones. La cementación del polietileno, cuando no sea posible su anclaje, en un cotilo metálico no cementado osteointegrado es una técnica que ofrece buenos resultados a medio plazo, y que minimiza las complicaciones que conlleva el recambio del componente acetabular, sin comprometer su estabilidad (AU)

Objective. In uncemented revision total hip replacement due to polyethylene wear, the metal cup needs to be maintained when its stability is checked during surgery, only replacing the polyethylene that is cemented if anchoring is not possible. The aim of the present study was to evaluate the medium-term clinical and radiological results of a polyethylene liner cemented into an osseointegrated acetabular shell component. Material and method. A retrospective analysis was performed on 15 patients in whom the surgical indication was polyethylene wear, with a mean follow-up of 6.1 years (range 3.5-9.7 years). The Harris Hip Score was used to assess the clinical results before surgery and at the end of follow-up. Anteroposterior and axial X-rays of the hip were taken to rule out complications. Results. The mean Harris Hip Score improved, increasing from 64.7points before the surgery to 80.3 at the end of follow-up. The osteolytic lesions disappeared, or at least the size did not increase, in the follow-up X-rays. One patient (6.7%) suffered 2 dislocation episodes that were treated without the need for surgery. Another patient presented with aseptic loosening of the femoral stem that required a replacement. Conclusions. Cementing the polyethylene liner, when anchoring is not possible, in an uncemented osseointegrated metal shell is a technique that offers good results in the medium term, and which may minimise the complications that may occur with the replacement of the shell component, without compromising its stability (AU)

The effect of application time of two types of bone cement on the cement-bone interface strength.

The aim of this study was to investigate whether the application time of bone cement would have an effect on the cement-bone interface strength in two types of commercially available bone cements. CMW1 Radiopaque(®) (CMW1) and SmartSetHV(®) (SmartSet) were applied to bovine cancellous bone specimens at 2 and at 4 min. Specimens were loaded to failure and the shear strength of the cement-bone interface was calculated. The mean shear strength (±standard deviation) of the cement-bone interface was 2.79 ± 1.29 MPa for CMW1 applied at 2 min; 1.35 ± 0.89 MPa for CMW1 applied at 4 min; 2.93 ± 1.21 MPa for SmartSet applied at 2 min and 3.00 ± 1.11 MPa for SmartSet applied at 4 min. Compared to all other groups, the cement-bone interface strength was significantly lower when CMW1 was applied to the bone specimens at 4 min (p < 0.05). There was no significant difference in the cement-bone interface strength when SmartSet was applied to bone at 2 and at 4 min. Under these testing conditions, the cement-bone interface strength was not affected by the time of application of SmartSet to bone. However, it was significantly lower when CMW1 was applied to bone at 4 min.

Optimisation of a two-liquid component pre-filled acrylic bone cement system: a design of experiments approach to optimise cement final properties.

The initial composition of acrylic bone cement along with the mixing and delivery technique used can influence its final properties and therefore its clinical success in vivo. The polymerisation of acrylic bone cement is complex with a number of processes happening simultaneously. Acrylic bone cement mixing and delivery systems have undergone several design changes in their advancement, although the cement constituents themselves have remained unchanged since they were first used. This study was conducted to determine the factors that had the greatest effect on the final properties of acrylic bone cement using a pre-filled bone cement mixing and delivery system. A design of experiments (DoE) approach was used to determine the impact of the factors associated with this mixing and delivery method on the final properties of the cement produced. The DoE illustrated that all factors present within this study had a significant impact on the final properties of the cement. An optimum cement composition was hypothesised and tested. This optimum recipe produced cement with final mechanical and thermal properties within the clinical guidelines and stated by ISO 5833 (International Standard Organisation (ISO), International standard 5833: implants for surgery-acrylic resin cements, 2002), however the low setting times observed would not be clinically viable and could result in complications during the surgical technique. As a result further development would be required to improve the setting time of the cement in order for it to be deemed suitable for use in total joint replacement surgery.

Influence of instrumentation techniques and irrigating solutions on bond strength of glass fiber posts to root dentin.

This study sought to evaluate how instrumentation techniques and irrigating solutions affected the bond strength of glass fiber posts. For this study, 80 human maxillary central incisors were selected. Endodontic access was obtained, root canal length was measured, and the coronal third was prepared using Gates-Glidden drills. The specimens were embedded in acrylic resin and randomly assigned to 8 groups (n = 10): manual instrumentation only (Group 1), rotary instrumentation only (Group 2), irrigation with 2.5% sodium hypochlorite (NaOCl) (Group 3), irrigation with 2% chlorhexidine (CHX) (Group 4), manual instrumentation and irrigation with 2.5% NaOCl (Group 5), manual instrumentation and irrigation with 2% CHX (Group 6), rotary instrumentation and irrigation with 2.5% NaOCl (Group 7), and rotary instrumentation and irrigation with 2% CHX (Group 8). Specimens in Groups 5-8 also received a 1 minute final rinse with ethylenediaminetetraacetic acid. Canals were filled and the specimens stored for 30 days in distilled water. The restoration material was removed down to the apical 4 mm of the root canal. The glass fiber posts were luted with resin cement and stored for 24 hours at 37°C. Specimens were subjected to a tensile strength test at a constant speed of 1.0 mm/minute and a load of 2,000 kgf. The results were analyzed by analysis of variance and Tukey's test. Irrigation with 2.5% NaOCl reduced the bond strength of fiber posts significantly (P < 0.01), while CHX showed no effect (P > 0.05). It was concluded that irrigation with 2.5% NaOCl has a negative effect on micromechanical retention of glass fiber posts, whether manual or rotary instrumentation is used.

Direct evidence of "damage accumulation" in cement mantles surrounding femoral hip stems retrieved at autopsy: cement damage correlates with duration of use and BMI.

The "damage accumulation" phenomenon has not been quantitatively demonstrated in clinical cement mantles surrounding femoral hip stems. We stained transverse sections of 11 postmortem retrieved femoral hip components fixed with cement using fluorescent dye-penetrant and quantified cement damage, voids, and cement-bone interface gaps in epifluorescence and white light micrographs. Crack density (Cr.Dn), crack length-density (Cr.Ln.Dn), porosity, and cement-bone interface gap fraction (c/b-gap%) were calculated, normalized by mantle area. Multiple regression tests showed that cement damage (Cr.Ln.Dn. & Cr.Dn.) was significantly positively correlated (r(2)=0.98, p<0.001) with "duration of use" and body mass index ("BMI") but not cement mantle "porosity". There were significant interactions: "duration of use"*"BMI" was strongly predictive (p<0.005) of Cr.Dn.; and "duration of use"*"porosity" was predictive (p=0.04) of Cr.Ln.Dn. Stem related cracks accounted for approximately one fifth of Cr.Dn and one third of Cr.Ln.Dn. The mean c/b-gap% was 13.8% but it did not correlate (r(2)=0.01, p=0.8) with duration of use. We concluded that duration-dependent fatigue damage accumulation occurred during in vivo use. BMI strongly influenced cement crack length and the rate of new crack formation over time. Voids did not increase the rate of crack initiation but appeared to have promoted crack growth over time. Although not progressive, substantial bone resorption at the cement-bone interface appeared to be common.

Femoral impaction bone allografting with an Exeter cemented collarless, polished, tapered stem in revision hip replacement: a mean follow-up of 10.5 years.

Femoral impaction bone allografting has been developed as a means of restoring bone stock in revision total hip replacement. We report the results of 75 consecutive patients (75 hips) with a mean age of 68 years (35 to 87) who underwent impaction grafting using the Exeter collarless, polished, tapered femoral stem between 1992 and 1998. The mean follow-up period was 10.5 years (6.3 to 14.1). The median pre-operative bone defect score was 3 (interquartile range (IQR) 2 to 3) using the Endo-Klinik classification. The median subsidence at one year post-operatively was 2 mm (IQR 1 to 3). At the final review the median Harris hip score was 80.6 (IQR 67.6 to 88.9) and the median subsidence 2 mm (IQR 1 to 4). Incorporation of the allograft into trabecular bone and secondary remodelling were noted radiologically at the final follow-up in 87% (393 of 452 zones) and 40% (181 of 452 zones), respectively. Subsidence of the Exeter stem correlated with the pre-operative Endo-Klinik bone loss score (p = 0.037). The degree of subsidence at one year had a strong association with long-term subsidence (p < 0.001). There was a significant correlation between previous revision surgery and a poor Harris Hip score (p = 0.028), and those who had undergone previous revision surgery for infection had a higher risk of complications (p = 0.048). Survivorship at 10.5 years with any further femoral operation as the end-point was 92% (95% confidence interval 82 to 97).

Clinical and radiological evaluation of revision hip arthroplasty using the cement-in-cement technique.

We reviewed 44 consecutive revision hip replacements in 38 patients performed using the cement-in-cement technique. All were performed for acetabular loosening in the presence of a well-fixed femoral component. The mean follow-up was 5.1 years (2 to 10.1). Radiological analysis at final follow-up indicated no loosening of the femoral component, except for one case with a continuous radiolucent line in all zones and peri-prosthetic fracture which required further revision. Peri-operative complications included nine proximal femoral fractures (20.4%) and perforation of the proximal femur in one hip. In five hips wiring or fixation with a braided suture was undertaken but no additional augmentation was required. There was an improvement in the mean Japanese Orthopaedic Association score from 55.5 (28 to 81) pre-operatively to 77.8 (40 to 95) at final follow-up (p < 0.001). Revision using a cement-in-cement technique allows increased exposure for acetabular revision and is effective in the medium term. Further follow-up is required to assess the long-term results in the light of in vitro studies which have questioned the quality of the cement-in-cement bond.

Long-term implant-bone fixation of the femoral component in total knee replacement.

Success of total knee replacement (TKR) depends on the prosthetic design. Aseptic loosening of the femoral component is a significant failure mode that has received little attention. Despite the clinical relevance of failures, no protocol is available to test long-term implant-bone fixation of TKR in vitro. The scope of this work was to develop and validate a protocol to assess pre-clinically the fixation of TKR femoral components. An in vitro protocol was designed to apply a simplified but relevant loading profile using a 6-degrees-of-freedom knee simulator for 1,000000 cycles. Implant-bone inducible micromotions and permanent migrations were measured at three locations throughout the test. After test completion, fatigue damage in the cement was quantified. The developed protocol was successfully applied to a commercial TKR. Additional tests were performed to exclude artefacts due to swelling or creep of the composite femur models. The components migrated distally; they tilted towards valgus in the frontal plane and in extension in the sagittal plane. The migration patterns were consistent with clinical roentgen-stereophotogrammetric recordings with TKR. Additional indicators were proposed that could quantify the tendency to loosen/stabilize. The type and amount of damage found in the cement, as well as the migration patterns, were consistent with clinical experience with the specific TKR investigated. The proposed pre-clinical test yielded repeatable results, which were consistent with the clinical literature. Therefore, its relevance and reliability was proved.

Integrity of the stem-cement interface in THA: effects of stem surface finish and cement porosity.

No consensus exists for the optimal surface finish on cemented total hip prosthesis stems. The purpose of this study was to determine the effects of stem finish and interfacial cement porosity on the integrity of the stem-cement interface. Simulated stems made of Co-Cr, having polished or matte surfaces, at room temperature or heated to 37 degrees C, were cemented into Sawbones simulated femurs. Push out testing of the stem-cement interface was performed immediately after cement polymerization and after two aging periods in 37 degrees C saline or 37 degrees C air, and the extent of interfacial porosity at the stem-cement interface was determined. Polished stems exhibited an average 60% greater interfacial strength than that of matte stems initially and up to 240% after aging treatments. Cement porosity at the stem-cement interface and incomplete cement interdigitation into surface asperities on matte stems likely allowed saline penetration into the stem-cement interface during wet aging, resulting in a rapid decrease of shear strength. Stem preheating to 37 degrees C virtually eliminated interfacial pores and resulted in greater shear strengths regardless of surface finish. Polished stem surfaces with stem preheating provided the best interfacial shear strength and sealing ability against saline penetration into the stem-cement interface and could result in increased longevity of stem fixation.

High-viscosity cement significantly enhances uniformity of cement filling in vertebroplasty: an experimental model and study on cement leakage.

STUDY DESIGN: Experimental study using a laboratory leakage model. OBJECTIVE: To examine the working hypothesis that high-viscosity cements will spread uniformly, thus significantly reducing the risk of leakage. SUMMARY OF BACKGROUND DATA: In vertebroplasty, forces that govern the flow of bone cement in the trabecular bone skeleton are an essential determinant of the uniformity of cement filling. Extraosseous cement leakage has been reported to be a major complication of this procedure. Leakage occurs due to the presence of a path of least resistance caused by irregularities in the trabecular bone or shell structure. Ideally, cement uniformly infiltrates the trabecular bone skeleton and does not favor specific paths. Cement viscosity is believed to affect the infiltration forces and flow during the procedure. Clinically, altering the time between cement mixing and delivery modifies the viscosity of bone cement. METHODS: An experimental model of the leakage phenomenon of vertebroplasty was developed. A path, simulating a blood vessel, was created in the model to perturb the forces underlying cement flow and to favor leakage. Cement of varying viscosities was injected in the model, and, thereafter, the filling pattern, cement mass that has leaked, time at which leakage occurred, and injection pressure were measured. RESULTS: A strong relationship was found between the uniformity of the filling pattern and the elapsed time from cement mixing and viscosity, respectively. Specifically, 3 distinct cement leakage patterns were observed: immediate leakage was observed when cement was injected 5-7 minutes following mixing. The cement was of a low viscosity and more than 50% of the total cement injected leaked. Moderate leakage was observed when injection occurred 7-10 minutes following mixing. Less than 10% of the cement leaked, and the viscosity was at a transient state between the low viscosity of immediate leakage and a higher viscosity, doughy cement. Cement leakage ceased completely when cement was delivered after 10 minutes. The viscosity of the cement in this case was high, and the cement was of a dough-like consistency. CONCLUSIONS: High-viscosity cement seems to stabilize cement flow. However, the forces required for the delivery of high-viscosity cement may approach or exceed the human physical limit of injection forces. Although the working time of the cement is about 17 minutes, it may not be manually injectable with a standard syringe and cannula after 10 minutes, at which time cement leakage ceased completely.

Osteochondral graft fixation using a bioresorbable bone cement.

Multiple osteochondral grafts can be used to resurface large joint defects in both humans and horses. In humans, immediate postoperative weight bearing can be prevented, however in the equine, it is unavoidable. Early weight bearing can create detrimental graft micromotion. The aim of this study was to investigate the role of a bioresorbable cement in improving the initial stability of multiple osteochondral graft repairs of large subchondral cystic lesions in the horse. Configurations employed for filling a 20mm diameter cylindrical defect included: (A) twelve 4.5mm diameter grafts with cement, (B) five 6.5mm diameter grafts with cement, (C) four each of 4.5mm and 6.5mm grafts with cement and (D) cement only. Intact bone slices (E) were also tested. Push-out tests were used to quantify construct to host sidewall interface fixation. Configuration (A) proved clinically impractical (n=3). Configurations (B) (n=6), and (C) (n=4) had statistically similar interface stiffnesses and failure stresses (43+/-8 and 30+/-12 MPa and 0.96+/-0.1 and 1.2+/-0.3 Mpa, respectively) suggesting that they are equally susceptible to interface movement in the immediate postoperative period. By way of comparison, defects filled only with cement had an average stiffness of 53+/-7MPa and failure stress of 1.8+/-0.3 MPa (n=6) while the intact femoral condyle demonstrated a stiffness of 108+/-7 MPa and failure stress of 18+/-0.4 MPa (n=6). Cement augmentation improved immediate postoperative stability of multiple osteochondral graft constructs over uncemented constructs, although in all cases the observed moduli of elasticity and yield stress values were lower than those observed for cement only and intact bone test specimens. (all numbers are mean+/-SEM).

The biomechanical effects of kyphoplasty on treated and adjacent nontreated vertebral bodies.

It remains unclear whether adjacent vertebral body fractures are related to the natural progression of osteoporosis or if adjacent fractures are a consequence of augmentation with bone cement. Experimental or computational studies have not completely addressed the biomechanical effects of kyphoplasty on adjacent levels immediately following augmentation. This study presents a validated two-functional spinal unit (FSU) T12-L2 finite element model with a simulated kyphoplasty augmentation in L1 to predict stresses and strains within the bone cement and bone of the treated and adjacent nontreated vertebral bodies. The findings from this multiple-FSU study and a recent retrospective clinical study suggest that changes in stresses and strains in levels adjacent to a kyphoplasty-treated level are minimal. Furthermore, the stress and strain levels found in the treated levels are less than injury tolerance limits of cancellous and cortical bone. Therefore, subsequent adjacent level fractures may be related to the underlying etiology (weakening of the bone) rather than the surgical intervention.

Effect of the hydrophilic nanofiller loading on the mechanical properties and the microtensile bond strength of an ethanol-based one-bottle dentin adhesive.

This study evaluated the hypothesis that if hydrophilic nanofillers were dispersed evenly within the adhesive layer under moist conditions, adding them to a one-bottle dentin adhesive might improve the mechanical properties of the adhesive layer, and accordingly increase the bond strength. The flexural strength (FS), the degree of conversion (DC), and the microtensile bond strength (MTBS) to the dentin of four experimental ethanol-based one-bottle dentin adhesives containing 0, 0.5, 1.0, and 3.0 wt % of 12-nm hydrophilic fumed silica were evaluated, and the distribution of the nanofillers were compared using transmission electron microscopy (TEM). Although the nanofiller content did not affect the DC, the FS tended to increase with increasing nanofiller content. The MTBS appeared to increase when up to 1.0 wt % of the nanofillers were added, but they were statistically not significant. However, when 3.0 wt % of the nanofillers were added, the MTBS decreased significantly comparing to the adhesive containing 0.5 wt % nanofillers (p < 0.05). The TEM image suggested that if the nanofillers within the adhesive were 3.0 wt % and applied to a wet dentin surface, they aggregated easily into large clusters and would decrease the MTBS.

The influence of the viscosity classification of an acrylic bone cement on its in vitro fatigue performance.

The goal of the present work was to investigate the influence of the viscosity classification of an acrylic bone cement on its in vitro fatigue performance, as determined in fully-reversed tension-compression (+/-15 MPa) fatigue tests. The test matrix comprised six commercially available bone cements [Orthoset1, (OS1), Orthoset(R)3 (OS3), CemexRX (CRX), Cemex XL (CXL), Palacos R (PR) and Osteopal (OP)], two methods of mixing the cement constituents (hand-mixing and vacuum-mixing), two methods of fabricating the test specimens (direct molding and molding followed by machining), two specimen cross-sectional shapes (rectangular or "flat" and circular or "round"), and four test frequencies (1, 2, 5, and 10 Hz). In total, 185 specimens, distributed among 20 sets, were tested. The test results (number of fatigue stress cycles, N_f) were processed using the linearized transformation of the three-parameter Weibull distribution, whence estimates of the Weibull mean, N_[WM], were obtained. Statistical analysis of the ln N_f results (Mann-Whitney test; alpha<0.05) and a comparison of the N_[WM] estimates for specimen sets in which the formulations have essentially the same composition but different viscosity classification (namely, OS1 versus OS3, CRX versus CXL, and PR versus OP) showed that, in the majority of the comparisons carried out, the viscosity classification of a bone cement does not exert a significant influence on its in vitro fatigue performance.

Avaliação das adaptações de restaurações indiretas: estudo in vivo / Study in vivo of the marginal gaps of dental castings

No presente estudo, buscou-se verificar, em pacientes cadastrados em clínica de serviço público/RJ, a adaptação das restaurações metálicas fundidas e mêtalo-cerâmicas, associando a liga metálica, o cimento e a técnica de cimentação empregados. Foram analisadas as restaurações de 60 pacientes de ambos os sexos, bem como seus prontuários. Os resultados evidenciaram que 100 por cento das restaurações foram cimentadas com cimento fosfato de zinco; 90 por cento das restaurações foram fundidas com liga de estanho/prata (Primmalloy) e 10 por cento com liga de cobre/alumínio (Duracast). Quanto à técnica de cimentação, 80 por cento das restaurações foram cimentadas com o dispositivo Medart e 20 por cento com pressão digital. Quanto às desadaptações, concluiu-se que nenhuma restauração estava com desadaptações menores que 50µ. Tinham discrepâncias 83,33 por cento das restaurações, entre 150 e 250µ, independentemente do cimento, da liga metálica e da técnica de cimentação

Use of explicit criteria for total hip joint replacement fixation techniques.

We developed a tool to judge the appropriateness of indications and fixation mechanisms for total hip joint replacement (THJR) and applied it to a sample of patients. Criteria were developed using a modified Delphi panel judgment process, following the RAND methodology (RAM). We recruited, during 1 year, patients with a diagnosis of osteoarthritis undergoing THJR in five public hospitals. The appropriateness of the THJR intervention and the fixation mechanism was judged by the explicit criteria developed by a panel of experts. Of the 216 scenarios scored by the panel for the use of each of three fixation mechanisms, the cemented fixation was considered inappropriate in 69.5%, versus just 33.3% for the non cemented. Of those scenarios considered appropriate, the most appropriate mechanism of fixation was considered to be non cemented (74.4%), while cemented (17.8%) and hybrid (7.8%) scenarios were scored as appropriate less often. The previous explicit criteria were applied to 583 real patients. After evaluation of the interventions, 30% of the fixation mechanisms used were considered appropriate, while 21.8% inappropriate. Appropriate use of fixation mechanisms varied among hospitals. RAM can provide explicit criteria to help in clinical decision making and evaluating indications for a THJR intervention. Nevertheless, in the case of the appropriateness of fixation mechanisms, due to the lack of evidence, the panel criteria were biased towards the non cemented technique, which had important implications for the evaluation of some hospitals.