[Oblique Lumbar Interbody Fusion Combined With 4-Screw Fixation for Treating Two-Level Degenerative Lumbar Diseases:A Finite Element Study].

Objective To demonstrate the feasibility of oblique lumbar interbody fusion (OLIF) combined with 4-screw fixation for treating two-level lumbar degenerative diseases.Methods An intact finite element model of L3-S1 (M0) was constructed and validated.Then,we constructed the M1 model by simulating OLIF surgery at L3/4 and L4/5 segments on the M0 model.By attachment of posterior 4-screw or 6-screw fixation to the M1 model,three 4-screw fixation models (M2-M4) and one 6-screw fixation model (M5) were established.The segmental and overall range of motion (ROM) and the peak von Mises stresses of superior endplate,cage,and posterior screw-rod were investigated under each implanted condition.Results Under the motion modes of forward flexion,backward extension,bilateral (left and right) flexion,and left and right rotation,the L3/4 ROM of M2 model and L4/5 ROM of M3 model increased,while the L3/4 and L4/5 ROM of M4 and M5 models significantly decreased compared with those of M1 model.Under all motion modes,the L4 superior endplate in M2 model and the L5 superior endplate in M3 model showed the maximum peak von Mises stress,and the peak von Mises stresses of L4 and L5 superior endplates in M4 and M5 models were close.The L3/4 cage in M2 model and the L4/5 cage in M3 model showcased the largest peak von Mises stress,and the peak von Mises stresses of cages in M4 and M5 models were close.The peak stresses of internal fixation in M2-M5 models were close.Conclusion Four-screw fixation can replace 6-screw fixation in the OLIF surgery for treating two-level degenerative lumbar diseases.

Fully automated determination of robotic pedicle screw accuracy and precision utilizing computer vision algorithms.

Historically, pedicle screw accuracy measurements have relied on CT and expert visual assessment of the position of pedicle screws relative to preoperative plans. Proper pedicle screw placement is necessary to avoid complications, cost and morbidity of revision procedures. The aim of this study was to determine accuracy and precision of pedicle screw insertion via a novel computer vision algorithm using preoperative and postoperative computed tomography (CT) scans. Three cadaveric specimens were utilized. Screw placement planning on preoperative CT was performed according to standard clinical practice. Two experienced surgeons performed bilateral T2-L4 instrumentation using robotic-assisted navigation. Postoperative CT scans of the instrumented levels were obtained. Automated segmentation and computer vision techniques were employed to align each preoperative vertebra with its postoperative counterpart and then compare screw positions along all three axes. Registration accuracy was assessed by preoperatively embedding spherical markers (tantalum beads) to measure discrepancies in landmark alignment. Eighty-eight pedicle screws were placed in 3 cadavers' spines. Automated registrations between pre- and postoperative CT achieved sub-voxel accuracy. For the screw tip and tail, the mean three-dimensional errors were 1.67 mm and 1.78 mm, respectively. Mean angular deviation of screw axes from plan was 1.58°. For screw mid-pedicular accuracy, mean absolute error in the medial-lateral and superior-inferior directions were 0.75 mm and 0.60 mm, respectively. This study introduces automated algorithms for determining accuracy and precision of planned pedicle screws. Our accuracy outcomes are comparable or superior to recent robotic-assisted in vivo and cadaver studies. This computerized workflow establishes a standardized protocol for assessing pedicle screw placement accuracy and precision and provides detailed 3D translational and angular accuracy and precision for baseline comparison.

Zero-profile implant system versus novel plate systems after ACDF for comparison of sagittal balance parameters and clinical efficacy analysis.

BACKGROUND: The zero-profile implant system (Zero-P) and conventional plates have been widely used in anterior cervical discectomy and fusion (ACDF) to treat cervical spondylosis. The purpose of this study was to compare the effects of the application of Zero-P and new conventional plates (ZEVO, Skyline) in ACDF on the sagittal imaging parameters of cervical spondylosis patients and to analyze their clinical efficacy. METHODS: We conducted a retrospective study on 119 cervical spondylosis patients from January 2018 to December 2021, comparing outcomes between those receiving the Zero-P device (n = 63) and those receiving a novel conventional plate (n = 56, including 46 ZEVO and 10 Skyline plates) through ACDF. Cervical sagittal alignment was assessed pre- and postoperatively via lateral radiographs. The Japanese Orthopedic Association (JOA), Neck Disability Index (NDI), and visual analog scale (VAS) scores were recorded at baseline, after surgery, and at the 2-year follow-up to evaluate patient recovery and intervention success. RESULTS: There were significant differences in the postoperative C0-C2 Cobb angle and postoperative sagittal segmental angle (SSA) between patients in the novel conventional plate group and those in the Zero-P group (P < 0.05). Postoperatively, there were significant changes in the C2‒C7 Cobb angle, C0‒C2 Cobb angle, SSA, and average surgical disc height (ASDH) compared to the preoperative values in both patient groups (P < 0.05). Dysphagia in the immediate postoperative period was lower in the Zero-P group than in the new conventional plate group (0% in the Zero-P group, 7.14% in the novel conventional plate group, P = 0.046), and the symptoms disappeared within 2 years in both groups. There was no statistically significant difference between the two groups in terms of complications of adjacent spondylolisthesis (ASD) at 2 years postoperatively (3.17% in the Zero-P group, 8.93% in the novel conventional plate group; P = 0.252). According to the subgroup analysis, there were significant differences in the postoperative C2‒C7 Cobb angle, C0‒C2 Cobb angle, T1 slope, and ASDH between the ZEVO group and the Skyline group (P < 0.05). Compared with the preoperative scores, the JOA, NDI, and VAS scores of all groups significantly improved at the 2-year follow-up (P < 0.01). According to the subgroup analysis, the immediate postoperative NDI and VAS scores of the ZEVO group were significantly better than those of the Skyline group (P < 0.05). CONCLUSION: In ACDF, both novel conventional plates and Zero-P can improve sagittal parameters and related scale scores. Compared to the Zero-P plate, the novel conventional plate has a greater advantage in correcting the curvature of the surgical segment, but the Zero-P plate is less likely to produce postoperative dysphagia.

Can We Rely on Prophylactic Two-Level Vertebral Cement Augmentation in Long-Segment Adult Spinal Deformity Surgery to Reduce the Incidence of Proximal Junctional Complications?

Background and Objectives: Proximal junctional kyphosis (PJK) and failure (PJF), the most prevalent complications following long-segment thoracolumbar fusions for adult spinal deformity (ASD), remain lacking in defined preventive measures. We studied whether one of the previously reported strategies with successful results-a prophylactic augmentation of the uppermost instrumented vertebra (UIV) and supra-adjacent vertebra to the UIV (UIV + 1) with polymethylmethacrylate (PMMA)-could also serve as a preventive measure of PJK/PJF in minimally invasive surgery (MIS). Materials and Methods: The study included 29 ASD patients who underwent a combination of minimally invasive lateral lumbar interbody fusion (MIS-LLIF) at L1-2 through L4-5, all-pedicle-screw instrumentation from the lower thoracic spine to the sacrum, S2-alar-iliac fixation, and two-level balloon-assisted PMMA vertebroplasty at the UIV and UIV + 1. Results: With a minimum 3-year follow-up, non-PJK/PJF group accounted for fifteen patients (52%), PJK for eight patients (28%), and PJF requiring surgical revision for six patients (21%). We had a total of seven patients with proximal junctional fracture, even though no patients showed implant/bone interface failure with screw pullout, probably through the effect of PMMA. In contrast to the PJK cohort, six PJF patients all had varying degrees of neurologic deficits from modified Frankel grade C to D3, which recovered to grades D3 and to grade D2 in three patients each, after a revision operation of proximal extension of instrumented fusion with or without neural decompression. None of the possible demographic and radiologic risk factors showed statistical differences between the non-PJK/PJF, PJK, and PJF groups. Conclusions: Compared with the traditional open surgical approach used in the previous studies with a positive result for the prophylactic two-level cement augmentation, the MIS procedures with substantial benefits to patients in terms of less access-related morbidity and less blood loss also provide a greater segmental stability, which, however, may have a negative effect on the development of PJK/PJF.

Augmented Reality in Spine Surgery: A Case Study of Atlantoaxial Instrumentation in Os Odontoideum.

Despite advancement in surgical innovation, C1-C2 fixation remains challenging due to risks of screw malposition and vertebral artery (VA) injuries. Traditional image-based navigation, while useful, often demands that surgeons frequently shift their attention to external monitors, potentially causing distractions. In this article, we introduce a microscope-based augmented reality (AR) navigation system that projects both anatomical information and real-time navigation images directly onto the surgical field. In the present case report, we discuss a 37-year-old female who suffered from os odontoideum with C1-C2 subluxation. Employing AR-assisted navigation, the patient underwent the successful posterior instrumentation of C1-C2. The integrated AR system offers direct visualization, potentially minimizing surgical distractions. In our opinion, as AR technology advances, its adoption in surgical practices and education is anticipated to expand.

Comparative efficacy of zero-profile implant and conventional cage-plate implant in the treatment of single-level degenerative cervical spondylosis: a systematic review and meta-analysis.

BACKGROUND: In recent years, the zero-profile implant (Zero-p) has emerged as a promising internal fixation technique. Although studies have indicated its potential superiority over conventional cage-plate implant (Cage-plate) in the treatment of degenerative cervical spondylosis, there remains a lack of definitive comparative reports regarding its indications, safety, and efficacy. METHODS: A computerized search was conducted on English and Chinese databases, including PubMed, Web of Science, Cochrane Library, EMBASE, CNKI, Wanfang and VIP. Additionally, a manual search was meticulously carried out on Chinese medical journals, spanning from the inception of the respective databases until August 2023. The meta-analysis utilized a case-control study approach and was executed through the utilization of RevMan 5.3 software. Stringent quality evaluation and data extraction procedures were implemented to guarantee the reliability and validity of the findings. RESULTS: Nine high-quality studies with 808 patients were included. Meta-analysis showed that the operation time (MD = - 13.28; 95% CI (- 17.53, - 9.04), P < 0.00001), intraoperative blood loss (MD = - 6.61; 95% CI (- 10.47, - 2.75), P = 0.0008), incidence of postoperative dysphagia at various time points: within the first month after surgery (OR = 0.36; 95% CI (0.22, 0.58), P < 0.0001), 1-3 months after surgery (OR = 0.20; 95% CI (0.08, 0.49), P = 0.0004), the final follow-up (OR = 0.21; 95% CI (0.05, 0.83), P = 0.003) and the rate of postoperative adjacent disc degeneration (OR = 0.46; 95% CI (0.25, 0.84), P = 0.01) were significantly lower in the Zero-p group than in the Cage-plate group. Additionally, was also significantly lower in the Zero-p group. However, there were no significant differences in the JOA score, the final follow-up NDI score, surgical segmental fusion rate, postoperative height of adjacent vertebrae, or postoperative subsidence rate between the two groups. CONCLUSION: In summary, when treating single-segment degenerative cervical spondylosis, both internal fixation techniques are reliable and effective. However, Zero-P  implant offer several advantages over cage-plate implant, including shorter operation duration, less intraoperative blood loss, reduced postoperative dysphagia, and slower adjacent disc degeneration. Additionally, Zero-P implant has a broader application space, making them a preferred choice in certain cases.

The optimal introversion angle and length of pedicle screw to avoid L1-S1 vascular damage.

BACKGROUND: posterior pedicle screw fixation is common method, one of the most severe complications is iatrogenic vascular damage, no report investigated association of different introversion angles (INTAs) and length of pedicle screw. The aims were to investigate the optimal introversion angle and length of pedicle screw for improving the safety of the operation, and to analyze the differences of vascular damage types at L1-S1. METHODS: Lumbar CT imaging data from110 patients were analyzed by DICOM software, and all parameters were measured by new Cartesian coordinate system, INTAs (L1-L5:5°,10°,15°,S1: 0°, 5°,10°,15°), DO-AVC (the distance between the origin (O) with anterior vertebral cortex (AVC)), DAVC-PGVs (the distance between AVC and the prevertebral great vessels (PGVs)), DO-PGVs (the distance between the O and PGVs). At different INTAs, DAVC-PGVs were divided into four grades: Grade III: DAVC-PGVs ≤ 3 mm, Grade II: 3 mm < DAVC-PGVs ≤ 5 mm, Grade I: DAVC-PGVs > 5 mm, and N: the not touching PGVs. RESULTS: The optimal INTA was 5° at L1-L3, the left was 5° and the right was 15° at L4, and screw length was less than 50 mm at L1-L4. At L5, the left optimal INTA was 5° and the right was 10°, and screw length was less than 45 mm. The optimal INTA was 15° at S1, and screw length was less than 50 mm. However, screw length was less than 40 mm when the INTA was 0° or 5° at S1. CONCLUSIONS: At L5-S1, the risk of vascular injury is the highest. INTA and length of the pedicle screw in lumbar operation are closely related. 3 mm interval of screw length may be more preferable to reduce vascular damage.

The postoperative clinical effects of utilizing 3D printed (Ti6Al4V) interbody fusion cages in posterior lumbar fusion: A retrospective cohort study.

BACKGROUND: The research focused on the postoperative effect of using interbody fusion cage in lumbar posterior lamina decompression and interbody fusion with pedicle screw by comparing the postoperative effect of using 3D printing (Ti6Al4V) and PEEK material interbody fusion cage. METHODS: Ninety-one patients with lumbar degenerative diseases from the Department of Spine Surgery of Tianjin Hospital were included in the study cohort. They were divided into 3D group (n = 39) and PEEK group (n = 52) according to the use of interbody fusion cage. The imaging data of the patients were collected and the postoperative data of the 2 groups were compared to evaluate patients' health status and the recovery of lumbar structure and function after operation. RESULTS: Combined with the degree of fusion, the clinical effect of 3D printing titanium alloy interbody fusion cage was comprehensively judged. At the last follow-up, the JOA score, ODI index, VAS, prolo function score, and SF-36 scale of the 2 groups showed that the clinical symptoms were better than those before operation (P < .05). The height of intervertebral disc, the area of intervertebral foramen and the physiological curvature of lumbar vertebrae increased in varying degrees after operation (P < .05). At the last follow-up, the vertebral cage fusion rates were as high as 89.13% and 90.91% in the 3D and PEEK groups, with collapse rates of 6.5% and 4.5%, respectively. There were 10 cases of cage displacement in 3D group and 7 cases of cage displacement in PEEK group. There was no significant difference between the 2 groups (P > .05). CONCLUSIONS: In conclusion, 3D printed (Ti6Al4V) interbody fusion cage can obtain good clinical effect in the surgical treatment of lumbar degenerative diseases. Posterior lumbar lamina decompression, bilateral pedicle screw fixation combined with 3D printed cage interbody fusion is excellent in rebuilding the stability of lumbar vertebrae. 3D printed interbody fusion cage can be an ideal substitute material for intervertebral bone grafting. The stable fusion time of interbody fusion cage after lumbar fusion is mostly from 3 months to half a year after operation.

Comparative clinical efficacy of percutaneous coaxial large-channel endoscopic lumbar interbody fusion and transforaminal lumbar interbody fusion for degenerative lumbar spinal stenosis: a retrospective study.

This study aimed to evaluate the clinical efficacy of percutaneous coaxial large-channel endoscopic lumbar interbody fusion (PCLE-LIF) and transforaminal lumbar interbody fusion (TLIF) in the treatment of degenerative lumbar spinal stenosis. The clinical data of patients with degenerative lumbar spinal stenosis who underwent PCLE-LIF (experimental group) and TLIF (control group) surgery from September 2019 to September 2021 were retrospectively analyzed. We collected clinical data and compared the two groups in terms of perioperative parameters, treatment response rate, inflammatory response markers, postoperative complications, postoperative pain, and functional recovery. The results showed that the treatment outcomes in the experimental group were significantly better than those in the control group. Specifically, perioperative parameters and inflammatory response markers in the experimental group were significantly better than those in the control group, with statistically significant differences (P < 0.05). The overall treatment response rate in the experimental group was significantly higher than that in the control group (P < 0.05). Meanwhile, the incidence of postoperative complications in the experimental group was lower than that in the control group, postoperative VAS pain scores and ODI functional scores were lower, and postoperative JOA functional scores were higher than those in the control group, with statistically significant differences (P < 0.05). In conclusion, PCLE-LIF appears to be a promising technique with better clinical outcomes in the treatment of degenerative lumbar spinal stenosis.

Accuracy and postoperative assessment of robot-assisted placement of pedicle screws during scoliosis surgery compared with conventional freehand technique: a systematic review and meta-analysis.

STUDY DESIGN: A systematic review and meta-analysis. BACKGROUND: The complexity of human anatomical structures and the variability of vertebral body structures in patients with scoliosis pose challenges in pedicle screw placement during spinal deformity correction surgery. Through technological advancements, robots have been introduced in spinal surgery to assist with pedicle screw placement. METHODS: A systematic search was conducted using PubMed, Cochrane, Embase, and CNKI databases and comparative studies assessing the accuracy and postoperative efficacy of pedicle screw placement using robotic assistance or freehand techniques in patients with scoliosis were included. The analysis evaluated the accuracy of screw placement, operative duration, intraoperative blood loss, length of postoperative hospital stay, and complications. RESULTS: Seven studies comprising 584 patients were included in the meta-analysis, with 282 patients (48.3%) in the robot-assisted group and 320 (51.7%) in the freehand group. Robot-assisted placement showed significantly better clinically acceptable screw placement results compared with freehand placement (odds ratio [OR]: 2.61, 95% confidence interval [CI]: 1.75-3.91, P < 0.0001). However, there were no statistically significant differences in achieving "perfect" screw placement between the two groups (OR: 1.52, 95% CI: 0.95-2.46, P = 0.08). The robot-assisted group had longer operation durations (mean deviation [MD]: 43.64, 95% CI: 22.25-64.74, P < 0.0001) but shorter postoperative hospital stays (MD: - 1.12, 95% CI: - 2.15 to - 0.08, P = 0.03) than the freehand group. There were no significant differences in overall complication rates or intraoperative blood loss between the two groups. There was no significant difference in Cobb Angle between the two groups before and after operation. CONCLUSION: Robot-assisted pedicle screw placement offers higher accuracy and shorter hospital stay than freehand placement in scoliosis surgery; although the robotics approach is associated with longer operative durations, similar complication rates and intraoperative blood loss.

The efficacy and safety of decompression with interspinous fixation for lumbar spondylolisthesis when compared with posterior lumbar interbody fusion: A pilot study.

Posterior lumbar interbody fusion (PLIF) is widely used to treat degenerative spondylolisthesis because it provides definitive decompression and fixation. Although it has several advantages, it has some disadvantages and risks, such as paraspinal muscle injury, potential intraoperative bleeding, postoperative pain, hardware failure, subsidence, and medical comorbidity. Lumbar decompressive bilateral laminectomy with interspinous fixation (DLISF) is less invasive and can be used on some patients with PLIF, but this has not been reported. To compare the efficacy and safety of DLISF in the treatment of low-grade lumbar spondylolisthesis with that of PLIF. We retrospectively analyzed the medical records of 81 patients with grade I spondylolisthesis, who had undergone PLIF or DLISF and were followed up for more than 1 year. Surgical outcomes, visual analog scale, radiologic outcomes, including Cobb angle and difference in body translation, and postoperative complications were assessed. Forty-one patients underwent PLIF, whereas 40 underwent DLISF. The operative times were 271.0 ±â€…57.2 and 150.6 ±â€…29.3 minutes for the PLIF and DLISF groups, respectively. The estimated blood loss was significantly higher in the PLIF group versus the DLISF group (290.7 ±â€…232.6 vs 122.2 ±â€…82.7 mL, P < .001). Body translation did not differ significantly between the 2 groups. Overall pain improved during the 1-year follow-up when compared with baseline data. Medical complications were significantly lower in the DLISF group, whereas perioperative complications and hardware issues were higher in the PLIF group. The outcomes of DLISF, which is less invasive, were comparable to PLIF outcomes in patients with low-grade spondylolisthesis. As a salvage technique, DLISF may be a good option when compared with PLIF.

High Strength and Shape Memory Spinal Fusion Device for Minimally Invasive Interbody Fusions.

Introduction: Lumbar interbody fusion is widely employed for both acute and chronic spinal diseases interventions. However, large incision created during interbody cage implantation may adversely impair spinal tissue and influence postoperative recovery. The aim of this study was to design a shape memory interbody fusion device suitable for small incision implantation. Methods: In this study, we designed and fabricated an intervertebral fusion cage that utilizes near-infrared (NIR) light-responsive shape memory characteristics. This cage was composed of bisphenol A diglycidyl ether, polyether amine D-230, decylamine and iron oxide nanoparticles. A self-hardening calcium phosphate-starch cement (CSC) was injected internally through the injection channel of the cage for healing outcome improvement. Results: The size of the interbody cage is reduced from 22 mm to 8.8 mm to minimize the incision size. Subsequent NIR light irradiation prompted a swift recovery of the cage shape within 5 min at the lesion site. The biocompatibility of the shape memory composite was validated through in vitro MC3T3-E1 cell (osteoblast-like cells) adhesion and proliferation assays and subcutaneous implantation experiments in rats. CSC was injected into the cage, and the relevant results revealed that CSC is uniformly dispersed within the internal space, along with the cage compressive strength increasing from 12 to 20 MPa. Conclusion: The results from this study thus demonstrated that this integrated approach of using a minimally invasive NIR shape memory spinal fusion cage with CSC has potential for lumbar interbody fusion.

Buck technique supplemented by temporary intersegmental pedicle screw fixation to repair lumbar spondylolysis in youth.

BACKGROUND: Lumbar spondylolysis is a bone defect in the pars interarticularis of the lumbar vertebral, which is a common cause of low back pain in youth. Although non-surgical treatment is a mainstream option, surgery is necessary for patients with persistent symptoms. Buck technique is widely used as a classical direct repair technique, but it cannot achieve reduction of low-grade spondylolisthesis and reconstruction of lumbosacral sagittal balance. We have described a novel surgical procedure based on Buck technique with temporary intersegmental pedicle screw fixation, and report a series of clinical outcomes in 5 patients to provide a reference for the clinical treatment of young lumbar spondylolysis. METHODS: Five young patients with symptomatic lumbar spondylolysis with a mean age of 19.20 ± 5.41 years underwent surgical treatment after an average of 7.60 ± 1.52 months of failure to respond to conservative treatment, using a new surgical procedure based on Buck technique combined with temporary intersegmental pedicle screw fixation. RESULTS: Five patients were successfully operated without serious complications such as nerve and vascular injury. The average operation time was 109.00 ± 7.42 min, the interpretative average blood loss was 148.00 ± 31.14 ml, and the average fusion time was 11.20 ± 1.64 months. All patients were followed up for 2 years after surgery, and the visual analogue score (VAS) of low back pain and Oswestry disability index (ODI) scores were significantly improved compared with those before surgery, and the Henderson's evaluation were rated excellent or good. After the removal of the internal fixation, it was observed that temporary intersegmental fixation could repair the isthmus, reduce lumbar spondylolisthesis, and reconstruct the sagittal balance of the lumbosacral vertebrae while preserving lumbar motion and preventing intervertebral disc degeneration. Postoperative MRI indicated the Pfirrmann classification of the affected discs: 1 case from grade III to grade II, 3 cases from grade II to grade I, and 1 case remained grade II. CONCLUSIONS: Buck technique supplemented by temporary intersegmental pedicle screw fixation is a highly applicable and effective method for the treatment of adolescent lumbar spondylolysis. The isthmic fusion is accurate, and temporary intersegmental fixation can effectively prevent disc degeneration and reconstruct the sagittal balance of lumbosacral vertebra.

Pedicle screw insertion into infected vertebrae reduces operative time and range of fixation in minimally invasive posterior fixation for thoracolumbar pyogenic spondylitis: a multicenter retrospective cohort study.

BACKGROUND: Minimally invasive posterior fixation surgery for pyogenic spondylitis is known to reduce invasiveness and complication rates; however, the outcomes of concomitant insertion of pedicle screws (PS) into the infected vertebrae via the posterior approach are undetermined. This study aimed to assess the safety and efficacy of PS insertion into infected vertebrae in minimally invasive posterior fixation for thoracolumbar pyogenic spondylitis. METHODS: This multicenter retrospective cohort study included 70 patients undergoing minimally invasive posterior fixation for thoracolumbar pyogenic spondylitis across nine institutions. Patients were categorized into insertion and skip groups based on PS insertion into infected vertebrae, and surgical data and postoperative outcomes, particularly unplanned reoperations due to complications, were compared. RESULTS: The mean age of the 70 patients was 72.8 years. The insertion group (n = 36) had shorter operative times (146 versus 195 min, p = 0.032) and a reduced range of fixation (5.4 versus 6.9 vertebrae, p = 0.0009) compared to the skip group (n = 34). Unplanned reoperations occurred in 24% (n = 17) due to surgical site infections (SSI) or implant failure; the incidence was comparable between the groups. Poor infection control necessitating additional anterior surgery was reported in four patients in the skip group. CONCLUSIONS: PS insertion into infected vertebrae during minimally invasive posterior fixation reduces the operative time and range of fixation without increasing the occurrence of unplanned reoperations due to SSI or implant failure. Judicious PS insertion in patients with minimal bone destruction in thoracolumbar pyogenic spondylitis can minimize surgical invasiveness.

Comparison of No Tap (two-step) and tapping robotic assisted cortical bone trajectory screw insertion.

Workflow for cortical bone trajectory (CBT) screws includes tapping line-to-line or under tapping by 1 mm. We describe a non-tapping, two-step workflow for CBT screw placement, and compare the safety profile and time savings to the Tap (three-step) workflow. Patients undergoing robotic assisted 1-3 level posterior fusion with CBT screws for degenerative conditions were identified and separated into either a No-Tap or Tap workflow. Number of total screws, screw-related complications, estimated blood loss, operative time, robotic time, and return to the operating room were collected and analyzed. There were 91 cases (458 screws) in the No-Tap and 88 cases (466 screws) in the Tap groups, with no difference in demographics, revision status, ASA grade, approach, number of levels fused or diagnosis between cohorts. Total robotic time was lower in the No-Tap (26.7 min) versus the Tap group (30.3 min, p = 0.053). There was no difference in the number of malpositioned screws identified intraoperatively (10 vs 6, p = 0.427), screws converted to freehand (3 vs 3, p = 0.699), or screws abandoned (3 vs 2, p = 1.000). No pedicle/pars fracture or fixation failure was seen in the No-Tap cohort and one in the Tap cohort (p = 1.00). No patients in either cohort were returned to OR for malpositioned screws. This study showed that the No-Tap screw insertion workflow for robot-assisted CBT reduces robotic time without increasing complications.

Biomechanical evaluation of reinsertion and revision screws in the subaxial cervical vertebrae.

BACKGROUND: This study aimed to evaluate the biomechanical effects of reinserted or revised subaxial cervical vertebral screws. METHODS: The first part aimed to gauge the maximum insertional torque (MIT) of 30 subaxial cervical vertebrae outfitted with 4.0-mm titanium screws. A reinsertion group was created wherein a screw was wholly removed and replaced along the same trajectory to test its maximum pullout strength (MPOS). A control group was also implemented. The second part involved implanting 4.0-mm titanium screws into 20 subaxial cervical vertebrae, testing them to failure, and then reinserting 4.5-mm revision screws along the same path to determine and compare the MIT and MPOS between the test and revision groups. RESULTS: Part I findings: No significant difference was observed in the initial insertion's maximum insertion torque (MIT) and maximum pull-out strength (MPOS) between the control and reinsertion groups. However, the MIT of the reinsertion group was substantially decreased compared to the first insertion. Moderate to high correlations were observed between the MIT and MPOS in both groups, as well as between the MIT of the first and second screw in the reinsertion group. Part II, the MIT and MPOS of the screw in the test group showed a strong correlation, while a modest correlation was observed for the revision screw used in failed cervical vertebrae screw. Additionally, the MPOS of the screw in the test group was significantly higher than that of the revision screw group. CONCLUSION: This study suggests that reinsertion of subaxial cervical vertebrae screws along the same trajectory is a viable option that does not significantly affect fixation stability. However, the use of 4.5-mm revision screws is inadequate for failed fixation cases with 4.0-mm cervical vertebral screws.

[Application of self-stabilizing zero-profile three-dimensional printed artificial vertebral bodies for treatment of cervical spondylotic myelopathy].

Objective: To evaluate the safety and effectiveness of applying self-stabilizing zero-profile three-dimensional (3D) printed artificial vertebral bodies in anterior cervical corpectomy and fusion (ACCF) for cervical spondylotic myelopathy. Methods: A retrospective analysis was conducted on 37 patients diagnosed with cervical spondylotic myelopathy who underwent single-level ACCF using either self-stabilizing zero-profile 3D-printed artificial vertebral bodies ( n=15, treatment group) or conventional 3D-printed artificial vertebral bodies with titanium plates ( n=22, control group) between January 2022 and February 2023. There was no significant difference in age, gender, lesion segment, disease duration, and preoperative Japanese Orthopedic Association (JOA) score between the two groups ( P>0.05). Operation time, intraoperative bleeding volume, hospitalization costs, JOA score and improvement rate, incidence of postoperative prosthesis subsidence, and interbody fusion were recorded and compared between the two groups. Results: Compared with the control group, the treatment group had significantly shorter operation time and lower hospitalization costs ( P<0.05); there was no significant difference in intraoperative bleeding volume between the two groups ( P>0.05). All patients were followed up, with a follow-up period of 6-21 months in the treatment group (mean, 13.7 months) and 6-19 months in the control group (mean, 12.7 months). No dysphagia occurred in the treatment group, while 5 cases occurred in the control group, with a significant difference in the incidence of dysphagia between the two groups ( P<0.05). At 12 months after operation, both groups showed improvement in JOA scores compared to preoperative scores, with significant differences ( P<0.05); however, there was no significant difference in the JOA scores and improvement rate between the two groups ( P>0.05). Radiographic examinations showed the interbody fusion in both groups, and the difference in the time of interbody fusion was not significant ( P>0.05). At last follow-up, 2 cases in the treatment group and 3 cases in the control group experienced prosthesis subsidence, with no significant difference in the incidence of prosthesis subsidence ( P>0.05). There was no implant displacement or plate-screw fracture during follow-up. Conclusion: The use of self-stabilizing zero-profile 3D-printed artificial vertebral bodies in the treatment of cervical spondylotic myelopathy not only achieves similar effectiveness to 3D-printed artificial vertebral bodies, but also reduces operation time and the incidence of postoperative dysphagia.

[Treatment of cervical ossification of posterior longitudinal ligament with titanium alloy trabecular bone three-dimensional printed artificial vertebral body].

Objective: To evaluate the effectiveness of using titanium alloy trabecular bone three-dimensional (3D) printed artificial vertebral body in treating cervical ossification of the posterior longitudinal ligament (OPLL). Methods: A retrospective analysis was conducted on clinical data from 45 patients with cervical OPLL admitted between September 2019 and August 2021 and meeting the selection criteria. All patients underwent anterior cervical corpectomy and decompression, interbody bone graft fusion, and titanium plate internal fixation. During operation, 21 patients in the study group received titanium alloy trabecular bone 3D printed artificial vertebral bodies, while 24 patients in the control group received titanium cages. There was no significant difference in baseline data such as gender, age, disease duration, affected segments, or preoperative pain visual analogue scale (VAS) score, Japanese Orthopaedic Association (JOA) score, Neck Disability Index (NDI), vertebral height, and C 2-7Cobb angle ( P>0.05). Operation time, intraoperative blood loss, and occurrence of complications were recorded for both groups. Preoperatively and at 3 and 12 months postoperatively, the functionality and symptom relief were assessed using JOA scores, VAS scores, and NDI evaluations. The vertebral height and C 2-7 Cobb angle were detected by imaging examinations and the implant subsidence and intervertebral fusion were observed. Results: The operation time and incidence of complications were significantly lower in the study group than in the control group ( P<0.05), while the difference in intraoperative blood loss between the two groups was not significant ( P>0.05). All patients were followed up 12-18 months, with the follow-up time of (14.28±4.34) months in the study group and (15.23±3.54) months in the control group, showing no significant difference ( t=0.809, P=0.423). The JOA score, VAS score, and NDI of the two groups improved after operation, and further improved at 12 months compared to 3 months, with significant differences ( P<0.05). At each time point, the study group exhibited significantly higher JOA scores and improvement rate compared to the control group ( P<0.05); but there was no significantly difference in VAS score and NDI between the two groups ( P>0.05). Imaging re-examination showed that the vertebral height and C 2-7Cobb angle of the two groups significantly increased at 3 and 12 months after operation ( P<0.05), and there was no significant difference between 3 and 12 months after operation ( P>0.05). At each time point, the vertebral height and C 2-7Cobb angle of the study group were significantly higher than those of the control group ( P<0.05), and the implant subsidence rate was significantly lower than that of the control group ( P<0.05). However, there was no significant difference in intervertebral fusion rate between the two groups ( P>0.05). Conclusion: Compared to traditional titanium cages, the use of titanium alloy trabecular bone 3D-printed artificial vertebral bodies for treating cervical OPLL results in shorter operative time, fewer postoperative complications, and lower implant subsidence rates, making it superior in vertebral reconstruction.

Enhancing spinal bone anchor pull-out resistance with an L-shaped anchor.

The success rate of spinal fusion surgery is mainly determined by the fixation strength of the spinal bone anchors. This study explores the use of an L-shaped spinal bone anchor that is intended to establish a macro-shape lock with the posterior cortical layer of the vertebral body, thereby increasing the pull-out resistance of the anchor. The performance of this L-shaped anchor was evaluated in lumbar vertebra phantoms (L1-L5) across four distinct perpendicular orientations (lateral, medial, superior, and inferior). During the pull-out experiments, the pull-out force, and the displacement of the anchor with respect to the vertebra was measured which allowed the determination of the maximal pull-out force (mean: 123 N ± 25 N) and the initial pull-out force, the initial force required to start motion of the anchor (mean: 23 N ± 16 N). Notably, the maximum pull-out force was observed when the anchor engaged the cortical bone layer. The results demonstrate the potential benefits of utilising a spinal bone anchor featuring a macro-shape lock with the cortical bone layer to increase the pull-out force. Combining the macro shape-lock fixation method with the conventional pedicle screw shows the potential to significantly enhance the fixation strength of spinal bone anchors.

3D CT modeling demonstrates the anatomic feasibility of S1AI screw trajectory for spinopelvic fixation in neuromuscular scoliosis.

PURPOSE: In patients with neuromuscular scoliosis undergoing posterior spinal fusion, the S2 alar iliac (S2AI) screw trajectory is a safe and effective method of lumbopelvic fixation but can lead to implant prominence. Here we use 3D CT modeling to demonstrate the anatomic feasibility of the S1 alar iliac screw (S1AI) compared to the S2AI trajectory in patients with neuromuscular scoliosis. METHODS: This retrospective study used CT scans of 14 patients with spinal deformity to create 3D spinal reconstructions and model the insertional anatomy, max length, screw diameter, and potential for implant prominence between 28 S2AI and 28 S1AI screw trajectories. RESULTS: Patients had a mean age of 14.42 (range 8-21), coronal cobb angle of 85° (range 54-141), and pelvic obliquity of 28° (range 4-51). The maximum length and diameter of both screw trajectories were similar. S1AI screws were, on average, 6.3 ± 5 mm less prominent than S2AI screws relative to the iliac crests. S2AI screws were feasible in all patients, while in two patients, posterior elements of the lumbar spine would interfere with S1AI screw insertion. CONCLUSION: In this cohort of patients with neuromuscular scoliosis, we demonstrate that the S1AI trajectory offers comparable screw length and diameter to an S2AI screw with less implant prominence. An S1AI screw, however, may not be feasible in some patients due to interference from the posterior elements of the lumbar spine.