FEM Modeling Strategies: Application to Mechanical and Dielectric Sensitivities of Love Wave Devices in Liquid Medium.

This paper presents an extended work on the Finite Element Method (FEM) simulation of Love Wave (LW) sensors in a liquid medium. Two models are proposed to simulate the multiphysical response of the sensor. Both are extensively described in terms of principle, composition and behavior, making their applications easily reproducible by the sensor community. The first model is a Representative Volume Element (RVE) simulating the transducer and the second focuses on the sensor's longitudinal (OXZ) cut which simulates the multiphysical responses of the device. Sensitivity of the LW device to variations in the rheological and dielectric properties of liquids is estimated and then compared to a large set of measurements issued from LW sensors presenting different technological characteristics. This integral approach allows for a deeper insight into the multiphysical behavior of the LW sensor. This article also explores the advantages and drawbacks of each model. Both are in good accordance with the measurements and could be used for various applications, for which a non-exhaustive list is proposed in the conclusion.

Mobile Acoustic Wave Platform Deployment in the Amazon River: Impact of the Water Sample on the Love Wave Sensor Response.

This paper presents an experimental platform allowing in situ measurement in an aqueous medium using an acoustic Love wave sensor. The aim of this platform, which includes the sensor, a test cell for electrical connections, a microfluidic chip, and a readout electronic circuit, is to realize a first estimation of water quality without transportation of water samples from the field to the laboratory as a medium-term objective. In the first step, to validate the ability of such a platform to operate in the field and in Amazonian water, an isolated and difficult-to-access location, namely, the floodplain Logo Do Curuaï in the Brazilian Amazon, was chosen. The ability of such a platform to be transported, installed on site, and used is discussed in terms of user friendliness and versatility. The response of the Love wave sensor to in situ water samples is estimated according to the physical parameters of Amazonian water. Finally, the very good quality of the acoustic response is established, potential further improvements are discussed, and the paper is concluded.

Love Acoustic Wave-Based Devices and Molecularly-Imprinted Polymers as Versatile Sensors for Electronic Nose or Tongue for Cancer Monitoring.

Cancer is a leading cause of death worldwide and actual analytical techniques are restrictive in detecting it. Thus, there is still a challenge, as well as a need, for the development of quantitative non-invasive tools for the diagnosis of cancers and the follow-up care of patients. We introduce first the overall interest of electronic nose or tongue for such application of microsensors arrays with data processing in complex media, either gas (e.g., Volatile Organic Compounds or VOCs as biomarkers in breath) or liquid (e.g., modified nucleosides as urinary biomarkers). Then this is illustrated with a versatile acoustic wave transducer, functionalized with molecularly-imprinted polymers (MIP) synthesized for adenosine-5'-monophosphate (AMP) as a model for nucleosides. The device including the thin film coating is described, then static measurements with scanning electron microscopy (SEM) and electrical characterization after each step of the sensitive MIP process (deposit, removal of AMP template, capture of AMP target) demonstrate the thin film functionality. Dynamic measurements with a microfluidic setup and four targets are presented afterwards. They show a sensitivity of 5 Hz·ppm(-1) of the non-optimized microsensor for AMP detection, with a specificity of three times compared to PMPA, and almost nil sensitivity to 3'AMP and CMP, in accordance with previously published results on bulk MIP.

Route to smooth silica-based surfaces decorated with novel self-assembled monolayers (SAMs) containing glycidyl-terminated very long hydrocarbon chains.

Novel glycidyl-terminated organosilicon coupling agents possessing a trialkoxysilyl head group and a very long hydrocarbon chain (C22) were synthesized. Their ability to afford densely packed self-assembled monolayers (SAMs) grafted on silica-based surfaces was investigated. Transmission FT-IR spectra showed that the most regular films were obtained by using trichloracetic acid as the catalyst (10 M%). Atomic force microscopy (AFM) and optical ellipsometry were consistent with well ordered monolayers exhibiting a marked decrease of the surface roughness. Epifluorescence microscopy revealed that these SAMs possessed a better surface reactivity than monolayers obtained with the commercially available (3-glycidoxypropyl) trimethoxysilane (GPTS) upon grafting of a fluorescent probe (dansylcadaverin). Moreover, direct attachment of fluorescent antibodies (RAG-TRITC) through covalent binding led to higher mean fluorescence intensities, showing that these new SAMs possess high potential for the immobilization of biological molecules.

A Love wave immunosensor for whole E. coli bacteria detection using an innovative two-step immobilisation approach.

The efficiency of a monomolecular film of (3-glycidoxypropyl) trimethoxysilane (GPTS) on a shear horizontal guided (Love) acoustic wave immunosensor to detect whole Escherichia coli (E. coli) bacteria is demonstrated. Direct anti-E. coli antibodies grafting onto the sensor surface did not lead to a significant bacteria immobilisation, partially attributed to the SiO2 sensor surface roughness. An innovative method has been set up to get around this difficulty and to detect whole bacteria. It consists in grafting goat anti-mouse antibodies (GAM) onto the sensor surface in a first step and introducing E. coli bacteria mixed with anti-E. coli antibodies onto the sensor in a second step. We describe the characteristics of such a technique like sample preparation time (lower than 30 min) and temperature improvements. A 37 degrees C experimental temperature led to the fastest bacteria binding kinetic, reducing the total analysis time. This method enables to keep the specificity of the antibody/antigen interaction and provides significant results in less than 1h. This leads to a detection threshold of 10(6) bacteria/ml in a 500 microl chamber.

Study of viscoelastic effect on the frequency shift of microcantilever chemical sensors.

Microcantilevers coated with a chemically sensitive layer are increasingly being used in chemical detection systems. The sensitive coating, often a polymer, absorbs specific molecules, which can be detected by monitoring the shift in the mechanical resonant frequency. Usually, the frequency shift resulting from molecular absorption is interpreted as a mass loading effect. However, mass loading is not the only effect that has an impact on the frequency shift; the viscoelastic properties of the sensitive coating also are affected by the sorption process. Sorption-induced modulus changes are typically difficult to characterize. However, it is known that the sorption of analyte molecules in a polymer coating results in the plasticization of the coating. In most cases, the polymer becomes more rubbery with increasing concentration of analyte molecules, i.e., the coating becomes softer with increasing loss modulus, and the storage modulus decreases. Using a new analytical model developed for the resonant frequency expression of a hybrid microcantilever (elastic base and viscoelastic layer), the effects of the modification of the storage and loss moduli of the sensitive layer on the resonant frequency are examined. The main conclusion of this analytical study is that, even if the sensitive coating moduli are small compared to the base cantilever's Young's modulus, the effect of the change in the viscoelastic coating properties could contribute significantly to the overall frequency shift (8-23% in the simulations depending on the coating thickness, with even higher contributions for other sets of problem parameters).

Coupled determination of gravimetric and elastic effects on two resonant chemical sensors: love wave and microcantilever platforms.

The objective of this paper is to couple theoretical and experimental results from microcantilevers and Love-wave acoustic devices in order to identify and separate mass loading effects from elastic effects. This is important in the perspective of sensing applications. For that, a thin-film polymer is deposited on both resonant platforms. It is demonstrated that microcantilevers are essentially mass sensitive. They allow one to determine the polymer layer thickness, which is validated by optical profilometry measurements. Then, taking into account this thickness, theoretical modeling and experimental measurements with Love-wave devices permit one to estimate an equivalent elastic shear modulus of the thin-film polymer at high frequency. Results are interesting if one is to fully understand and optimize (bio)chemical sensor responses.