Photochemical properties and toxicity of fluoroquinolone antibiotics impacted by complexation with metal ions in different pH solutions.

Acid-base dissociable antibiotic-metal complexes are known to be emerging contaminants in the aquatic environments. However, little information is available on the photochemical properties and toxicity of these complex forms. This study investigated the spectral properties of three fluoroquinolones (FQs) with and without metal ions Fe(III), Cu(II), and Al(III) in solutions under different pH conditions, as well as evaluated the changes in toxicity due to the complex with these metal ions using luminescent bacteria (vibrio fischeri). FQs showed a higher tendency to coordinate metal ions under alkaline conditions compared to neutral and acidic conditions, and the formation of complexes weakened the ultraviolet-absorbing ability of FQs. At pH = 7.0, Cu(II) quenched the fluorescence intensity of FQs. Moreover, their Fourier-transform infrared spectroscopy and X-ray photoelectron spectroscopy were explored, revealing that the coordination sites of Cu(II) in three FQs were situated in a bidentate manner through the oxygen atom of the deprotonated carboxyl group and cyclic carbonyl oxygen atom. This conclusion was further verified by the theory of molecular surface electrostatic potential. In addition, except for complexes of ciprofloxacin-metals, enhanced toxicity of FQs upon coordination with Fe(III) was observed, while reduced toxicity was found for coordination with Cu(II) and Al(III). These results are important for accurately evaluating the photochemical behavior and risk of these antibiotics in aquatic environments contaminated with metal ions.

Fundamental Insights into the Direct Electron Transfer Mechanism on Ag Atomic Cluster.

The nonradical oxidation pathway for pollutant degradation in Fenton-like catalysis is favorable for water treatment due to the high reaction rate and superior environmental robustness. However, precise regulation of such reactions is still restricted by our poor knowledge of underlying mechanisms, especially the correlation between metal site conformation of metal atom clusters and pollutant degradation behaviors. Herein, we investigated the electron transfer and pollutant oxidation mechanisms of atomic-level exposed Ag atom clusters (AgAC) loaded on specifically crafted nitrogen-doped porous carbon (NPC). The AgAC triggered a direct electron transfer (DET) between the terminal oxygen (Oα) of surface-activated peroxodisulfate and the electron-donating substituents-containing contaminants (EDTO-DET), rendering it 11-38 times higher degradation rate than the reported carbon-supported metal catalysts system with various single-atom active centers. Heterocyclic substituents and electron-donating groups were more conducive to degradation via the EDTO-DET system, while contaminants with high electron-absorbing capacity preferred the radical pathway. Notably, the system achieved 79.5% chemical oxygen demand (COD) removal for the treatment of actual pharmaceutical wastewater containing 1053 mg/L COD within 30 min. Our study provides valuable new insights into the Fenton-like reactions of metal atom cluster catalysts and lays an important basis for revolutionizing advanced oxidation water purification technologies.

Degradation and detoxification of 6PPD-quinone in water by ultraviolet-activated peroxymonosulfate: Mechanisms, byproducts, and impact on sediment microbial community.

N-(1,3-dimethylbutyl)-N'-phenyl-p-phenylenediamine quinone (6PPD-Q) has been identified to induce acute toxicity to multifarious aquatic organisms at exceptionally low concentrations. The ubiquity and harmful effects of 6PPD-Q emphasize the critical need for its degradation from water ecosystems. Herein, we explored the transformation of 6PPD-Q by an ultraviolet-activated peroxymonosulfate (UV/PMS) system, focusing on mechanism, products and toxicity variation. Results showed that complete degradation of 6PPD-Q was achieved when the initial ratio of PMS and 6PPD-Q was 60:1. The quenching experiments and EPR tests indicated that SO4•- and •OH radicals were primarily responsible for 6PPD-Q removal. Twenty-one degradation products were determined through high-resolution orbitrap mass spectrometry, and it was postulated that hydroxylation, oxidative cleavage, quinone decomposition, ring oxidation, as well as rearrangement and deamination were the major transformation pathways of 6PPD-Q. Toxicity prediction revealed that all identified products exhibited lower acute and chronic toxicities to fish, daphnid and green algae compared to 6PPD-Q. Exposure experiments also uncovered that 6PPD-Q considerably reduced the community diversity and altered the community assembly and functional traits of the sediment microbiome. However, we discovered that the toxicity of 6PPD-Q degradation solutions was effectively decreased, suggesting the superior detoxifying capability of the UV/PMS system for 6PPD-Q. These findings highlight the underlying detrimental impacts of 6PPD-Q on aquatic ecosystems and enrich our understanding of the photochemical oxidation behavior of 6PPD-Q.

Scaling-Free Cathodes: Enabling Electrochemical Extraction of High-Purity Nano-CaCO3 and -Mg(OH)2 in Seawater.

For electrochemical application in seawater or brine, continuous scaling on cathodes will form insulation layers, making it nearly impossible to run an electrochemical reaction continuously. Herein, we report our discovery that a cathode consisting of conical nanobundle arrays with hydrophobic surfaces exhibits a unique scaling-free function. The hydrophobic surfaces will be covered with microbubbles created by electrolytic water splitting, which limits scale crystals from standing only on nanotips of conical nanobundles, and the bursting of large bubbles formed by the accumulation of microbubbles will cause a violent disturbance, removing scale crystals automatically from nanotips. Benefiting from the scaling-free properties of the cathode, high-purity nano-CaCO3 (98.9%) and nano-Mg(OH)2 (99.5%) were extracted from seawater. This novel scaling-free cathode is expected to eliminate the inherent limitations of electrochemical technology and open up a new route to seawater mining.

Suspended particulate matter-biofilm aggregates benefit microcystin removal in turbulent water but trigger toxicity toward Daphnia magna.

Suspended particulate matter (SPM) and biofilm are critical in removing contaminants in aquatic environments, but the environmental behavior and ecological toxicity of SPM-biofilm aggregates modulated by turbulence intensities are largely unknown. This study determined the removal pathways of microcystin-LR (MC-LR) by SPM and its biofilm under different turbulence intensities (2.25 × 10-3, 1.01 × 10-2, and 1.80 × 10-2 m2/s3). Then, we evaluated the toxicity of SPM-biofilm aggregates to Daphnia magna. The results revealed that SPM contributed to the adsorption of MC-LR, and the removal of MC-LR can be accelerated with biofilm formation on SPM, with 95.66 % to 97.45 % reduction in MC-LR concentration under the studied turbulence intensities. Higher turbulence intensity triggered more frequent contact of SPM and MC-LR, formed compact but smaller clusters of SPM-biofilm aggregates, and enhanced the abundance of mlrA and mlrB; thus benefiting the adsorption, biosorption, and biodegradation of MC-LR. Furthermore, the SPM-biofilm aggregates formed in turbulent water triggered oxidative stress to Daphnia magna, while a weak lethal toxic effect was identified under moderate turbulence intensity. The results indicate that the toxicity of SPM-biofilm aggregates fail to display a linear relationship with turbulence intensity. These findings offer new perspectives on understanding the environmental behavior and ecological outcomes of SPM and its biofilms in turbulent aquatic environments.

Preparation and Properties of PA10T/PPO Blends Compatibilized with SEBS-g-MAH.

Plant-derived PA10T is regarded as one of the most promising semi-aromatic polyamides; however, shortcomings, including low dimensional accuracy, high moisture absorption, and relatively high dielectric constant and loss, have impeded its extensive utilization. Polymer blending is a versatile and cost-effective method to fabricate new polymeric materials with excellent comprehensive performance. In this study, various ratios of PA10T/PPO blends were fabricated via melt blending with the addition of a SEBS-g-MAH compatibilizer. Molau test and scanning electron microscopy (SEM) were employed to study the influence of SEBS-g-MAH on the compatibility of PA10T and PPO. These studies indicated that SEBS-g-MAH effectively refines the domain size of the dispersed PPO phase and improves the dispersion stability of PPO particles within a hexafluoroisopropanol solvent. This result was attributed to the in situ formation of the SEBS-g-PA10T copolymer, which serves as a compatibilizer. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) results showed that the melting-crystallization behavior and thermal stability of blends closely resembled that of pure PA10T. Dynamic mechanical analysis (DMA) revealed that as the PPO content increased, there was a decrease in the glass transition temperature and storage modulus of PA10T. The water absorption rate, injection molding shrinkage, dielectric properties, and mechanical strength of blends were also systematically investigated. As the PPO content increased from 10% to 40%, the dielectric loss at 2.5 GHz decreased significantly from 0.00866 to 0.00572, while the notched Izod impact strength increased from 7.9 kJ/m2 to 13.7 kJ/m2.

Dissecting the ecological risks of sulfadiazine degradation intermediates under different advanced oxidation systems: From toxicity to the fate of antibiotic resistance genes.

The incomplete degradation of antibiotics in water can produce intermediates that carry environmental risks and thus warrant concerns. In this study, the degradation of high concentrations of antibiotic sulfadiazine (SDZ) by advanced oxidation processes that leverage different reactive oxide species was systematically evaluated in terms of the influence of different degradation intermediates on the propagation of antibiotic resistance genes (ARGs). The ozone, persulfate, and photocatalytic oxidation systems for SDZ degradation are dominated by ozone, direct electron transfer, and singlet oxygen, hole, and superoxide radicals, respectively. These processes produce 15 intermediates via six degradation pathways. Notably, it was determined that three specific intermediates produced by the ozone and persulfate systems were more toxic than SDZ. In contrast, the photocatalytic system did not produce any intermediates with toxicity exceeding that of SDZ. Microcosm experiments combined with metagenomics confirmed significant changes in microbiota community structure after treatment with SDZ and its intermediates, including significant changes in the abundance of Flavobacterium, Dungenella, Archangium, and Comamonas. This treatment also led to the emergence of sulfonamide ARGs. The total abundance of sulfonamide ARGs was found to be positively correlated with residual SDZ concentration, with the lowest total abundance observed in the photocatalytic system. Additionally, the correlation analysis unveiled microbiota carrying sulfonamide ARGs.

Bioaugmented biological contact oxidation reactor for treating simulated textile dyeing wastewater.

In this study, modified polyamide fibers were used as biocarriers to enrich dense biofilms in a multi-stage biological contact oxidation reactor (MBCOR) in which partitioned wastewater treatment zone (WTZ) and bioaugmentation zone (BAZ) were established to enhance the removal of methyl orange (MO) and its metabolites while minimizing sludge yields. WTZ exhibited high biomass loading capacity (5.75 ± 0.31 g/g filler), achieving MO removal rate ranging from 68 % to 86 % under different aeration condition within 8 h in which the most dominant genus Chlorobium played an important role. In the BAZ, Pseudoxanthomonas was the dominant genus while carbon starvation stimulated the enrichment of chemoheterotrophy and aerobic_chemoheterotrophy genes thereby enhanced the microbial utilization of cell-released substrates, MO as well as its metabolic intermediates. These results revealed the mechanism bioaugmentation on MBCOR in effectively eliminating both MO and its metabolites.

Ultrasonic degradation of per-and polyfluoroalkyl substances (PFAS), aqueous film-forming foam (AFFF) and foam fractionate (FF).

The ubiquitousness of per- and polyfluoroalkyl substances (PFAS) is a big concern and PFAS remediation is urgently needed such as via degradation. While previous studies have explored ultrasonic degradation of PFAS, work evaluating the operational parameters is rare, especially concerning real wastes such as aqueous film-forming foam (AFFF) and foam fractionate (FF). This study investigates the key operational parameters affecting the degradation efficiency of PFAS, encompassing ultrasonication frequency (580-1144 kHz), power intensity (125-187.5 W), initial concentration (0.08-40 ppm), treatment duration (0.5-3 h), sample volume (100-500 mL), and PFAS structure (perfluorooctanoic acid or PFOA; perfluorooctane sulfonate or PFOS; 6:2 fluorotelomer sulfonate or 6:2 FTS). The defluorination kinetics is different from the removal/degradation kinetics due to the generation of degradation intermediates, suggesting the complex degradation mechanism, which should be evaluated to close the mass balance effectively. Notably, the optimised ultrasonic system achieves ∼125%/∼115% defluorination in AFFF/FF example wastes (compared to ∼65%/∼97% removal) despite their complex composition and the involvement of total oxidizable precursor (TOP) assay. In the meantime, a few new PFAS are detected in the post-treatments, including perfluorohexane sulfonic acid (PFHxS) and 10:2 fluorotelomer sulfonate (10:2 FTS) in the AFFF, and perfluorooctane sulfonamide (FOSA) and 8:2 fluorotelomer sulfonate (8:2 FTS) in the FF, again suggesting the complex degradation mechanism. Overall, ultrasonication is effective to degrade PFAS real example wastes, advancing its potential for scale-up applications.

Oxidation effects on Microcystis aeruginosa inactivation through various reactive oxygen species: Degradation efficiency, mechanisms, and physiological properties.

The study investigated the inactivation of Microcystis aeruginosa using a combined approach involving thermally activated peroxyacetic acid (Heat/PAA) and thermally activated persulfate (Heat/PDS). The Heat/PDS algal inactivation process conforms to first-order reaction kinetics. Both hydroxyl radical (•OH) and sulfate radical (SO4-•) significantly impact the disruption of cell integrity, with SO4-• assuming a predominant role. PAA appears to activate organic radicals (RO•), hydroxyl (•OH), and a minimal amount of singlet oxygen (1O2). A thorough analysis underscores persulfate's superior ability to disrupt algal cell membranes. Additionally, SO4-• can convert small-molecule proteins into aromatic hydrocarbons, accelerating cell lysis. PAA can accelerate cell death by diffusing into the cell membrane and triggering advanced oxidative reactions within the cell. This study validates the effectiveness of the thermally activated persulfate process and the thermally activated peroxyacetic acid as strategies for algae inactivation.

Green Strong Cornstalk Rind-Based Cellulose-PVA Aerogel for Oil Adsorption and Thermal Insulation.

Cellulose-based aerogel has attracted considerable attention for its excellent adsorption capacity, biodegradability, and renewability. However, it is considered eco-unfriendly due to defibrillation of agriculture waste and requires harmful/expensive chemical agents. In this study, cornstalk rind-based aerogel was obtained via the following steps: green H2O2/HAc delignification of cornstalk rind to obtain cellulose fibers, binding with carboxymethyl cellulose (CMC)/polyvinyl alcohol (PVA) and freeze-drying treatment, and hydrophobic modification with stearic acid. The obtained aerogel showed high compressive strength (200 KPa), which is apparently higher (about 32 kPa) than NaClO-delignified cornstalk-based cellulose/PVA aerogel. Characterization of the obtained aerogel through SEM, water contact angle, etc., showed high porosity (95%), low density (0.0198 g/cm-3), and hydrophobicity (water contact angle, 159°), resulting in excellent n-hexane adsorption capacity (35 g/g), higher (about 29.5 g/g) than NaClO-delignified cornstalk-based cellulose/PVA aerogel. The adsorbed oil was recovered by the extrusion method, and the aerogel showed excellent recyclability in oil adsorption.

Synthesis and Reduction Processes of Silver Nanowires in a Silver(I) Sulfamate-Poly (Vinylpyrrolidone) Hydrothermal System.

Silver (Ag) nanowires, as an important one-dimensional (1D) nanomaterial, have garnered wide attention, owing to their applications in electronics, optoelectronics, sensors, and other fields. In this study, an alternative hydrothermal route was developed to synthesize Ag nanowires via modified reduction of Ag+. Silver sulfamate plays an important role in the formation of Ag nanowires via controlled release of free Ag+. Results of controlled experiments and characterizations such as UV-vis spectroscopy, FTIR, XPS, and 1H NMR revealed that sulfamic acid does not function as a reductant, supporting by the generation of free Ag+ instead of Ag nanostructures in hydrothermally treated silver sulfamate solution. The initial reduction of Ag+ was induced by the combination of poly (vinylpyrrolidone) (PVP) end group and degradation products. This phenomenon was supported by abundant free Ag+ in the mixed preheated silver sulfamatic and preheated PVP aqueous solutions, indicating a second and distinct Ag+ autocatalytic reduction. Thus, the roles of different reagents and Ag+ reduction must be studied for nanomaterial syntheses.

Efficient and Selective Electrochemical Nitrate Reduction to N2 Using a Flow-Through Zero-Gap Electrochemical Reactor with a Reconstructed Cu(OH)2 Cathode: Insights into the Importance of Inter-Electrode Distance.

Electrochemically converting nitrate, a widely distributed nitrogen contaminant, into harmless N2 is a feasible and environmentally friendly route to close the anthropogenic nitrogen-based cycle. However, it is currently hindered by sluggish kinetics and low N2 selectivity, as well as scarce attention to reactor configuration. Here, we report a flow-through zero-gap electrochemical reactor that shows a high performance of nitrate reduction with 100% conversion and 80.36% selectivity of desired N2 in the chlorine-free system at 100 mg-N·L-1 NO3- while maintaining a rapid reduction kinetics of 0.07676 min-1. More importantly, the mass transport and current utilization efficiency are significantly improved by shortening the inter-electrode distance, especially in the zero-gap electrocatalytic system where the current efficiency reached 50.15% at 5 mA·cm-2. Detailed characterizations demonstrated that during the electroreduction process, partial Cu(OH)2 on the cathode surface was reconstructed into stable Cu/Cu2O as the active phase for efficient nitrate reduction. In situ characterizations revealed that the highly selective *NO to *N conversion and the N-N coupling step played crucial roles during the selective reduction of NO3- to N2 in the zero-gap electrochemical system. In addition, theoretical calculations demonstrated that improving the key intermediate *N coverage could effectively facilitate the N-N coupling step, thereby promoting N2 selectivity. Moreover, the environmental and economic benefits and long-term stability shown by the treatment of real nitrate-containing wastewater make our proposed electrocatalytic system more attractive for practical applications.

Mechanism of biochar composite (BN3Z0.5BC) activated peracetic acid for efficient antibiotic degradation: Synergistic effect between free radicals and non-free radicals.

This study utilized corn straw as the feedstock to synthesize biochar (BC) loaded with cobalt-zeolitic imidazolate framework nanoparticles and boron nitride quantum dots. The prepared BC composite, named BN3Z0.5BC, efficiently activated peracetic acid (PAA), resulting in the degradation of 94.8% of sulfadiazine (SDZ) in five minutes. Compared to pure BC, the SDZ removal rate increased nearly 5-fold. Mechanism analysis revealed that the main degradation pathway involves synergism between free and non-free radicals. The defect structure on the BC surface possesses a high charge density, stimulating PAA to produce more active species, while nitrogen-oxygen vacancy formation significantly promotes charge transfer. Besides, the unique structure of BC ensures good stability and recyclability, effectively controlling metal leaching. The BN3Z0.5BC/PAA system shows promising applicability across various water matrices, indicating a favorable application outlook.

Characteristics of CXE family of Salvia miltiorrhiza and identification of interactions between SmGID1s and SmDELLAs.

Carboxylesterase (CXE) is a class of hydrolases that contain an α/ß folding domain, which plays critical roles in plant growth, development, and stress responses. Based on the genomic and transcriptomic data of Salvia miltiorrhiza, the SmCXE family was systematically analyzed using bioinformatics. The results revealed 34 SmCXE family members in S. miltiorrhiza, and the SmCXE family could be divided into five groups (Group I, Group II, Group III, Group IV, and Group V). Cis-regulatory elements indicated that the SmCXE promoter region contained tissue-specific and development-related, hormone-related, stress-related, and photoresponsive elements. Transcriptome analysis revealed that the expression levels of SmCXE2 were highest in roots and flowers (SmCXE8 was highest in stems and SmCXE19 was highest in leaves). Further, two GA receptors SmCXE1 (SmGID1A) and SmCXE2 (SmGID1B) were isolated from the SmCXE family, which are homologous to other plants. SmGID1A and SmGID1B have conserved HGGSF motifs and active amino acid sites (Ser-Asp-Val/IIe), which are required to maintain their GA-binding activities. SmGID1A and SmGID1B were significantly responsive to gibberellic acid (GA3) and methyl jasmonate (MeJA) treatment. A subcellular assay revealed that SmCXE1 and SmCXE2 resided within the nucleus. SmGID1B can interact with SmDELLAs regardless of whether GA3 exists, whereas SmGID1A can only interact with SmDELLAs in the presence of GA3. A Further assay showed that the GRAS domain mediated the interactions between SmGID1s and SmDELLAs. This study lays a foundation for further elucidating the role of SmCXE in the growth and development of S. miltiorrhiza.

Efficacy of rhizobacteria Paenibacillus polymyxa SY42 for the biological control of Atractylodes chinensis root rot.

Atractylodes chinensis is one of the most commonly used bulk herbs in East Asia; however, root rot can seriously affect its quality and yields. In contrast to chemical pesticides, biological control strategies are environmentally compatible and safe. For this study, 68 antagonistic bacterial strains were isolated from the rhizospheres of healthy Atractylodes chinensis. Strain SY42 exhibited the most potent fungicidal activities, with inhibition rates against F. oxysporum, F. solani, and F. redolens of 67.07 %, 63.40 % and 68.45 %, respectively. Through morphological observation and molecular characterization, strain SY42 was identified as Paenibacillus polymyxa. The volatile organic components (VOCs) produced by SY42 effectively inhibited the mycelial growth of pathogenic fungi through diffusion. SY42 significantly inhibited the germination of pathogenic fungal spores. Following co-culturing with SY42, the mycelium of the pathogenic fungus was deformed, folded, and even ruptured. SY42 could produce cellulases and proteases to degrade fungal cell walls. Pot experiments demonstrated the excellent biocontrol efficacy of SY42. This study revealed that P. polymyxa SY42 inhibited pathogenic fungi through multiple mechanisms, which verified its utility as a biocontrol agent for the control of A. chinensis root rot.

Recent advances in electrospinning-nanofiber materials used in advanced oxidation processes for pollutant degradation.

Electrospun nanofiber membranes have emerged as a novel catalyst, demonstrating exceptional efficacy in advanced oxidation processes (AOPs) for the degradation of organic pollutants. Their superior performance can be attributed to their substantial specific surface area, high porosity, ease of modification, rapid recovery, and unparalleled chemical stability. This paper aims to comprehensively explore the progressive applications and underlying mechanisms of electrospun nanofibers in AOPs, which include Fenton-like processes, photocatalysis, catalytic ozonation, and persulfate oxidation. A detailed discussion on the mechanism and efficiency of the catalytic process, which is influenced by the primary components of the electrospun catalyst, is presented. Additionally, the paper examines how concentration, viscosity, and molecular weight affect the characteristics of the spinning materials and seeks to provide a thorough understanding of electrospinning technology to enhance water treatment methods. The review proposes that electrospun nanofiber membranes hold significant potential for enhancing water treatment processes using advanced oxidation methods. This is attributed to their advantageous properties and the tunable nature of the electrospinning process, paving the way for advancements in water treatment through AOPs.

Comprehensive Functional Analysis of the bZIP Family in Bletilla striata Reveals That BsbZIP13 Could Respond to Multiple Abiotic Stresses.

Basic leucine zipper (bZIP) transcription factors (TFs) are one of the largest families involved in plant physiological processes such as biotic and abiotic responses, growth, and development, etc. In this study, 66 members of the bZIP family were identified in Bletilla striata, which were divided into 10 groups based on their phylogenetic relationships with AtbZIPs. A structural analysis of BsbZIPs revealed significant intron-exon differences among BsbZIPs. A total of 63 bZIP genes were distributed across 16 chromosomes in B. striata. The tissue-specific and germination stage expression patterns of BsbZIPs were based on RNA-seq. Stress-responsive expression analysis revealed that partial BsbZIPs were highly expressed under low temperatures, wounding, oxidative stress, and GA treatments. Furthermore, subcellular localization studies indicated that BsbZIP13 was localized in the nucleus. Yeast two-hybrid (Y2H) and bimolecular fluorescence complementation (BiFC) assays suggested that BsbZIP13 could interact with multiple BsSnRK2s. The results of this study provide insightful data regarding bZIP TF as one of the stress response regulators in B. striata, while providing a theoretical basis for transgenic and functional studies of the bZIP gene family in B. striata.

Insights into electrochemical oxidation of tris(2-butoxyethyl) phosphate (TBOEP) in aquatic media: Degradation performance, mechanisms and toxicity changes of intermediate products.

Tris (2-butoxyethyl) phosphate (TBOEP) has gained significant attention due to its widespread presence and potential toxicity in the environment. In this study, the degradation of TBOEP in aquatic media was investigated using electrochemical oxidation technology. The anode Ti/SnO2-Sb/La-PbO2 demonstrated effective degradation performance, with a reaction constant (k) of 0.6927 min-1 and energy consumption of 1.24 kW h/m3 at 10 mA/cm2. CV tests, EPR tests, and quenching experiments confirmed that indirect degradation is the main degradation mechanism and ·OH radicals were the predominant reactive species, accounting for up to 93.8%. The presence of various factors, including Cl-, NO3-, HCO3- and humic acid (HA), inhibited the degradation of TBOEP, with the inhibitory effect dependent on the concentrations. A total of 13 intermediates were identified using UPLC-Orbitrap-MS/MS, and subsequent reactions led to their further degradation. Two main degradation pathways involving bond breaking, hydroxylation, and oxidation were proposed. Both Flow cytometry and the ECOSAR predictive model indicated that the intermediates exhibited lower toxic than the parent compound, resulting in a high detoxification rate of 95.9% for TBOEP. Although the impact of TBOEP on the phylum-level microbial community composition was found to be insignificant, substantial alterations in bacterial abundance were noted when examining the genus level. The dominant genus Methylotenera, representing 17.4% in the control group, decreased to 6.9% in the presence of TBOEP and slightly increased to 8.7% in the 4-min exposure group of degradation products. Electrochemical oxidation demonstrated its effectiveness for the degradation and detoxification of TBOEP in aqueous solutions, while it is essential to consider the potential impact of degradation products on sediment microbial communities.

Insight into typical photo-assisted AOPs for the degradation of antibiotic micropollutants: Mechanisms and research gaps.

Due to the incomplete elimination by traditional wastewater treatment, antibiotics are becoming emerging contaminants, which are proved to be ubiquitous and promote bacterial resistance in the aquatic systems. Antibiotic pollution has raised particular concerns, calling for improved methods to clean wastewater and water. Photo-assisted advanced oxidation processes (AOPs) have attracted increasing attention because of the fast reaction rate, high oxidation capacity and low selectivity to remove antibiotics from wastewater. On the basis of latest literature, we found some new breakthroughs in the degradation mechanisms of antibiotic micropollutants with respect to the AOPs. Therefore, this paper summarizes and highlights the degradation kinetics, pathways and mechanisms of antibiotics degraded by the photo-assisted AOPs, including the UV/O3 process, photo-Fenton technology, and photocatalysis. In the processes, functional groups are attacked by hydroxyl radicals, and major structures are destroyed subsequently, which depends on the classes of antibiotics. Meanwhile, their basic principles, current applications and influencing factors are briefly discussed. The main challenges, prospects, and recommendations for the improvement of photo-assisted AOPs are proposed to better remove antibiotics from wastewater.