Solvent-free automated thermal desorption-gas chromatography/mass spectrometry for direct screening of hazardous compounds in consumer textiles.

The global production of textiles utilizes numerous large-volume chemicals that may remain to some extent in the finished garments. Arylamines, quinolines, and halogenated nitrobenzene compounds are possible mutagens, carcinogens and/or skin sensitizers. For prevention, control of clothing and other textiles must be improved, especially those imported from countries without regulations of textile chemicals. An automated analytical methodology with on-line extraction, separation, and detection would largely simplify screening surveys of hazardous chemicals in textiles. Automated thermal desorption-gas chromatography/mass spectrometry (ATD-GC/MS) was developed and evaluated as a solvent-free, direct chemical analysis for screening of textiles. It requires a minimum of sample handling with a total run time of 38 min including sample desorption, chromatographic separation, and mass spectrometric detection. For most of the studied compounds, method quantification limit (MQL) was below 5 µg/g for 5 mg of textile sample, which is sufficiently low for screening and control of quinoline and arylamines regulated by EU. Several chemicals were detected and quantified when the ATD-GC/MS method was applied in a limited pilot screening of synthetic fiber garments. A number of arylamines were detected, where some of the halogenated dinitroanilines were found in concentrations up to 300 µg/g. This is ten times higher than the concentration limit for similar arylamines listed by the EU REACH regulation. Other chemicals detected in the investigated textiles were several quinolines, benzothiazole, naphthalene, and 3,5-dinitrobromobenzene. Based on the present results, we suggest ATD-GC/MS as a screening method for the control of harmful chemicals in clothing garments and other textiles.

Disperse azo dyes, arylamines and halogenated dinitrobenzene compounds in synthetic garments on the Swedish market.

BACKGROUND: Azobenzene disperse dyes (azo DDs) are well-known as textile allergens, but the knowledge of their occurrence in garments is low. The numerous azo DDs and dye components found in textiles constitute a potential health risk, but only seven azo DDs are included in the European baseline patch test series (EBS). OBJECTIVES: To investigate non-regulated azo DDs and dye components in synthetic garments on the Swedish market. METHODS: High-performance liquid chromatography/mass spectrometry, gas chromatography/mass spectrometry and computerized data mining. RESULTS: Sixty-two azo DDs were detected, with Disperse Red 167:1 occurring in 67%, and 14 other DDs each found in >20% of the garments. Notably, the EBS dyes were less common, three even not detected, while arylamines were frequently detected and exceeded 1 mg/g in several garments. Also, halogenated dinitrobenzenes were identified in 25% of the textiles. CONCLUSION: Azo DDs and dye components, in complex compositions and with large variations, occurred frequently in the synthetic garments. The arylamines were shown to occur at much higher levels compared to the azo DDs, suggesting the former constitute a potentially higher health risk. The role of arylamines and halogenated dinitrobenzenes in textile allergy has to be further investigated.

Suspect and non-target screening of chemicals in clothing textiles by reversed-phase liquid chromatography/hybrid quadrupole-Orbitrap mass spectrometry.

The global manufacturing of clothing is usually composed of multistep processes, which include a large number of chemicals. However, there is generally no information regarding the chemical content remaining in the finished clothes. Clothes in close and prolonged skin contact may thus be a significant source of daily human exposure to hazardous compounds depending on their ability to migrate from the textiles and be absorbed by the skin. In the present study, twenty-four imported garments on the Swedish market were investigated with respect to their content of organic compounds, using a screening workflow. Reversed-phase liquid chromatography coupled to electrospray ionization/high-resolution mass spectrometry was used for both suspect and non-target screening. The most frequently detected compound was benzothiazole followed by quinoline. Nitroanilines with suspected mutagenic and possible skin sensitization properties, and quinoline, a carcinogenic compound, were among the compounds occurring at the highest concentrations. In some garments, the level of quinoline was estimated to be close to or higher than 50,000 ng/g, the limit set by the REACH regulation. Other detected compounds were acridine, benzotriazoles, benzothiazoles, phthalates, nitrophenols, and organophosphates. Several of the identified compounds have logP and molecular weight values enabling skin uptake. This pilot study indicates which chemicals and compound classes should be prioritized for future quantitative surveys and control of the chemical content in clothing as well as research on skin transfer, skin absorption, and systemic exposure. The results also show that the current control and prevention from chemicals in imported garments on the Swedish market is insufficient.

Chemicals from textiles to skin: an in vitro permeation study of benzothiazole.

Despite the possible impact on human health, few studies have been conducted to assess the penetration and accumulation of contaminants in the skin after a prolonged contact with textile materials. In previous studies, we have shown that benzothiazole and its derivatives, as well as other potentially hazardous chemicals, often are present as textile contaminants in clothes available on the retail market. Since benzothiazole is a common contaminant in clothes, these can be a possible route for human chemical exposure, both systemic and onto the skin. To investigate this potential exposure, Franz-type and flow-through cells were used for the permeation studies together with a Strat-M® artificial membranes. Experiments were performed using solutions of benzothiazole, as well as contaminated textile samples in the donor chamber. Benzothiazole was demonstrated to penetrate through, as well as being accumulated in the membrane mimicking the skin. After 24 h, up to 62% of benzothiazole was found in the acceptor cell, while up to 37% was found absorbed in the skin mimicking membrane. It also was shown that there was release and permeation from contaminated fabrics. The results indicate that benzothiazole can be released from textile materials, penetrate through the skin, and further enter the human body. This will possibly also apply to other chemical contaminants in textiles, and the results of this study indicate that the presence of these textile contaminants entails potential health risks. A rough risk assessment was made for clothing textiles according to Environmental Protection Agency (EPA) and European regulations for carcinogenic and non-carcinogenic compounds, using literature data for benzothiazole.

Determination of heme in microorganisms using HPLC-MS/MS and cobalt(III) protoporphyrin IX inhibition of heme acquisition in Escherichia coli.

One of the main threats to the achievements in modern medicine is antimicrobial resistance. Molecular targeting of bacterial acquisition mechanisms of heme has been suggested to be an alternative to antibiotics. In the present study, HPLC-MS/MS combined with a simple clean-up based on liquid-liquid extraction has been developed and evaluated for simultaneous determination of heme and porphyrin heme precursors in microorganisms. Experimental design was used to optimize the extraction parameters, to obtain a method with high recovery, low matrix effects, and high precision. The effects of additives in the culture medium on the biosynthesis of heme were studied using Escherichia coli as a model microorganism. 5-Aminolaevulinic acid and hemin increased the heme concentration in E. coli by a factor of 1.5 and 4.5, respectively. Addition of 5-aminolaevulinic acid bypassed the E. coli negative feedback control of heme biosynthesis, which led to high amounts of intracellular porphyrins. The high heme concentration obtained when hemin was used as a culture additive shows that E. coli has an uptake of heme from its surroundings. In contrast, addition of cobalt protoporphyrin IX to the growth medium reduced the amount of heme in E. coli, demonstrating this compound's ability to mimic real heme and inhibit the heme acquisition mechanisms.

Influence of culture conditions on porphyrin production in Aggregatibacter actinomycetemcomitans and Porphyromonas gingivalis.

BACKGROUND: Increasing antibiotic resistance among pathogens has raised the demands for new treatment methods such as antimicrobial photodynamic therapy (aPDT) and phototherapy (PT). Experiments for investigating the effects of these methods are often performed in vitro, but the procedures for cultivation of microbes vary between different studies. The aim of this study has been to elucidate how the profile of endogenously produced porphyrins differs by changing the variables of bacteria culturing conditions. METHODS: Two oral pathogens, Aggregatibacter actinomycetemcomitans and Porphyromonas gingivalis, were selected as model organisms. The contents of porphyrins and heme in the bacteria were analysed with liquid chromatography-tandem mass spectrometry when bacteria was cultivated for different lengths of time (3-9 days), upon passaging as well as when growth medium were supplemented with or without horse blood. RESULTS: Both porphyrin and heme content in A. actinomycetemcomitans are highly affected by the age of the culture, and that the porphyrin profiles changes during cultivation. When cultivated colonies of A. actinomycetemcomitans were passaged onto a new, fresh growth medium a large change in porphyrin content occurred. Additional porphyrins were detected; uroporphyrin and 7-carboxylporphyrin, and the total porphyrin content increased up to 28 times. When P. gingivalis was grown on blood containing medium higher concentrations of protoporphyrin IX (2.5 times) and heme (5.4 times) were quantified compared to bacteria grown without blood. CONCLUSIONS: This study demonstrate that there is a need for more standardized culturing protocols when performing aPDT and PT experiments in vitro to avoid large variations in porphyrin profiles and concentrations, the aPDT/PT target compounds, depending on the culturing conditions.

Determination of aniline and quinoline compounds in textiles.

A simple method for simultaneous determination of twenty-one analytes, belonging to two classes of compounds, aromatic amines and quinolines, is presented. Several of the analytes considered in this study frequently occur in textiles goods on the open market and have been related to allergic contact dermatitis and/or are proven or suspected carcinogens. The method includes an efficient clean-up step using graphitized carbon black (GCB) that simplifies and improves the robustness of the subsequent GC-MS analysis. Briefly, after solvent extraction of the textile sample, the extract is passed through a GCB SPE cartridge that selectively retain dyes and other interfering compounds present in the matrix, producing a clean extract, suitable for GC-MS analysis, is obtained. The method was evaluated by spiking blank textiles with the selected analytes. Method quantification limits (MQL) ranged from 5 to 720ng/g depending on the analyte. The linear range of the calibration curves ranged over two order magnitude with coefficients of determination (R2) higher than 0.99. Recoveries ranged from 70 to 92% with RSDs 1.7-14%. The effectiveness of the method was tested on a variety of textile materials samples from different origin. In a pilot explorative survey, 2,6-dichloro-4-nitroaniline was detected in all the analysed clothing samples in concentrations ranging from 1.0 to 576µg/g. 2,4-dinitroaniline was detected in four of the seven samples with a highest concentration of 305µg/g. Quinoline was detected in all samples in concentrations ranging from 0.06 to 6.2µg/g.

The washout effect during laundry on benzothiazole, benzotriazole, quinoline, and their derivatives in clothing textiles.

In two previous papers, the authors have shown that benzothiazole, benzotriazole, quinoline, and several of their derivatives are widespread in clothing textile articles. A number of these compounds exhibit allergenic and irritating properties and, due to their octanol-water partition coefficient, are prone to be absorbed by the skin. Moreover, they are slightly soluble in water, which could make washing of clothes a route of emission into the environment. In the present study, the washout effect of benzothiazole, benzotriazole, quinoline, and some of their derivatives has been investigated. Twenty-seven textile samples were analyzed before, as well as after five and ten times of washing. The most abundant analyte was found to be benzothiazole, which was detected in 85 % of the samples with an average concentration of 0.53 µg/g (median 0.44 µg/g), followed by quinoline, detected in 81 % of the samples with an average concentration of 2.42 µg/g (median 0.21 µg/g). The average decrease in concentration for benzothiazoles was 50 % after ten times washing, while it was around 20 % for quinolines. The average emission to household wastewater of benzothiazoles and quinolines during one washing (5 kg of clothes made from polyester materials) was calculated to 0.5 and 0.24 g, respectively. These results strongly indicate that laundering of clothing textiles can be an important source of release of these compounds to household wastewater and in the end to aquatic environments. It also demonstrates a potential source of human exposure to these chemicals since considerable amounts of the compounds remain in the clothes even after ten times of washing.

Determination of porphyrins in oral bacteria by liquid chromatography electrospray ionization tandem mass spectrometry.

Biofilms in the oral cavity can be visualized by fluorescence and a common assumption is that the endogenously produced porphyrins in certain bacteria give rise to this fluorescence. Porphyrin content in oral bacteria has been sparingly investigated, and non-selective detection techniques such as utilizing the Soret fluorescence band of porphyrins are often used. In the present study, a quantitative and selective method for the determination of porphyrins in oral bacteria has been developed and validated using high performance liquid chromatography-tandem mass spectrometry. Lysis of bacteria using Tris-EDTA buffer together with ultrasonication showed high microbial killing efficiency ≥99.98%, and sample clean-up using C18-solid phase extraction resulted in low matrix effects ≤14% for all analytes. Using this method, the porphyrin content was determined in the two oral pathogens Aggregatibacter actinomycetemcomitans and Porphyromonas gingivalis, as well as for baker's yeast, Saccharomyces cerevisiae. Uroporphyrin, 7-carboxylporphyrin, 6-carboxylporphyrin, coproporphyrin, and protoporphyrin IX were identified in the investigated microorganisms, and it was shown that the porphyrin profile differs between the two bacteria, as well as for S. cerevisiae. To our knowledge, this is the first time the porphyrin profile has been determined for the bacterium A. actinomycetemcomitans.

Benzothiazole, benzotriazole, and their derivates in clothing textiles--a potential source of environmental pollutants and human exposure.

Textiles play an important role in our daily life, and textile production is one of the oldest industries. In the manufacturing chain from natural and/or synthetic fibers to the final clothing products, the use of many different chemicals is ubiquitous. A lot of research has focused on chemicals in textile wastewater, but the knowledge of the actual content of harmful chemicals in clothes sold on the retail market is limited. In this paper, we have focused on eight benzothiazole and benzotriazole derivatives, compounds rated as high production volume chemicals. Twenty-six clothing samples of various textile materials and colors manufactured in 14 different countries were analyzed in textile clothing using liquid chromatography tandem mass spectrometry. Among the investigated textile products, 11 clothes were for babies, toddlers, and children. Eight of the 11 compounds included in the investigation were detected in the textiles. Benzothiazole was present in 23 of 26 investigated garments in concentrations ranging from 0.45 to 51 µg/g textile. The garment with the highest concentration of benzothiazole contained a total amount of 8.3 mg of the chemical. The third highest concentration of benzothiazole (22 µg/g) was detected in a baby body made from "organic cotton" equipped with the "Nordic Ecolabel" ("Svanenmärkt"). It was also found that concentrations of benzothiazoles in general were much higher than those for benzotriazoles. This study implicates that clothing textiles can be a possible route for human exposure to harmful chemicals by skin contact, as well as being a potential source of environmental pollutants via laundering and release to household wastewater.

Quinolines in clothing textiles--a source of human exposure and wastewater pollution?

A production process in which the use of various types of chemicals seems to be ubiquitous makes the textile industry a growing problem regarding both public health as well as the environment. Among several substances used at each stage, the present study focuses on the quinolines, a class of compounds involved in the manufacture of dyes, some of which are skin irritants and/or classified as probable human carcinogens. A method was developed for the determination of quinoline derivatives in textile materials comprising ultrasound-assisted solvent extraction, solid phase extraction cleanup, and final analysis by gas chromatography/mass spectrometry. Quinoline and ten quinoline derivatives were determined in 31 textile samples. The clothing samples, diverse in color, material, brand, country of manufacture, and price, and intended for a broad market, were purchased from different shops in Stockholm, Sweden. Quinoline, a possible human carcinogen, was found to be the most abundant compound present in almost all of the samples investigated, reaching a level of 1.9 mg in a single garment, and it was found that quinoline and its derivatives were mainly correlated to polyester material. This study points out the importance of screening textiles with nontarget analysis to investigate the presence of chemicals in an unbiased manner. Focus should be primarily on clothing worn close to the body.

Determination of benzothiazole and benzotriazole derivates in tire and clothing textile samples by high performance liquid chromatography-electrospray ionization tandem mass spectrometry.

A high performance liquid chromatography-tandem mass spectrometry method utilizing electrospray ionization in positive and negative mode has been developed for the separation and detection of benzothiazole and benzotriazole derivates. Ultra-sonication assisted solvent extraction of these compounds has also been developed and the overall method demonstrated on a selected clothing textile and an automobile tire sample. Matrix effects and extraction recoveries, as well as linearity and limits of detection have been evaluated. The calibration curves spanned over more than two orders of magnitude with coefficients of correlation R(2)>0.99 and the limits of detection and the limits of quantification were in the range 1.7-58pg injected and 18-140pg/g, respectively. The extraction recoveries ranged between 69% and 102% and the matrix effects between 75% and 101%. Benzothiazole and benzotriazole derivates were determined in the textile sample and benzothiazole derivatives determined in the tire sample with good analytical performance.

Organophosphate and phthalate esters in standard reference material 2585 organic contaminants in house dust.

The levels of 22 phthalate diesters (phthalates) and organophosphate triesters (organophosphates) have been investigated in standard reference material 2585 (SRM 2585) "organic contaminants in house dust." Ultrasonic-assisted solvent extraction and solid-phase extraction on a Florisil adsorbent were used as the extraction and cleanup steps combined with analysis using gas chromatography-tandem mass spectrometry in positive ion chemical ionization mode. Seven phthalates were detected in the concentration range 1-570 µg/g. Di(2-ethylhexyl) phthalate was the major phthalate present at 570 µg/g. Ten organophosphates were detected in SRM 2585. Tris(2-butoxyethyl) phosphate was the predominant organophosphate at 82 µg/g, and nine organophosphates were determined at concentrations ranging from 0.19 to 2.3 µg/g. Five organophosphates were below the method detection limit, of which two were in level with the procedural blank. The applied extraction and cleanup method was evaluated for the analysis of SRM 2585. The extraction yield was ≥99%, except for tris(2-chloroethyl) phosphate (97%) and diethyl phthalate (98.5%). The problem of calibration curvature is addressed, and it is shown that the use of deuterated standards improves the analysis. The concentrations of ten organophosphate esters were determined in SRM 2585, and seven of these were compared with existing data. To our knowledge, this is the first report of the levels of the seven phthalates esters in SRM 2585 "organic contaminants in house dust."

Organophosphate and phthalate esters in indoor air: a comparison between multi-storey buildings with high and low prevalence of sick building symptoms.

An extensive study has been conducted on the prevalence of organophosphorous flame retardants/plasticizers and phthalate ester plasticizers in indoor air. The targeted substances were measured in 45 multi-storey apartment buildings in Stockholm, Sweden. The apartment buildings were classified as high or low risk with regard to the reporting of sick building symptoms (SBS) within the project Healthy Sustainable Houses in Stockholm (3H). Air samples were taken from two to four apartments per building (in total 169 apartments) to facilitate comparison within and between buildings. Association with building characteristics has been examined as well as association with specific sources by combining chemical analysis and exploratory uni- and multivariate data analysis. The study contributes to the overall perspective of levels of organophosphate and phthalate ester in indoor air enabling comparison with other studies. The results indicated little or no difference in the concentrations of the target substances between the two risk classifications of the buildings. The differences between the apartments sampled within (intra) buildings were greater than the differences between (inter) buildings. The concentrations measured in air ranged up to 1200 ng m(-3) for organophosphate esters and up to 11 000 ng m(-3) for phthalate esters. Results in terms of sources were discerned e.g. PVC flooring is a major source of benzylbutyl phthalate in indoor air.

An automated multidimensional preparative gas chromatographic system for isolation and enrichment of trace amounts of xenon from ambient air.

The monitoring of radioactive xenon isotopes is one of the principal methods for the detection of nuclear explosions in order to identify clandestine nuclear testing. In this work, a miniaturized, multiple-oven, six-column, preparative gas chromatograph was constructed in order to isolate trace quantities of radioactive xenon isotopes from ambient air, utilizing nitrogen as the carrier gas. The multidimensional chromatograph comprised preparative stainless steel columns packed with molecular sieves, activated carbon, and synthetic carbon adsorbents (e.g., Anasorb®-747 and Carbosphere®). A combination of purification techniques--ambient adsorption, thermal desorption, back-flushing, thermal focusing, and heart cutting--was selectively optimized to produce a well-defined xenon peak that facilitated reproducible heart cutting and accurate quantification. The chromatographic purification of a sample requires approximately 4 h and provides complete separation of xenon from potentially interfering components (such as water vapor, methane, carbon dioxide, and radon) with recovery and accuracy close to 100%. The preparative enrichment process isolates and concentrates a highly purified xenon gas fraction that is suitable for subsequent ultra-low-level γ-, ß/γ-spectroscopic or high-resolution mass spectrometric measurement (e.g., to monitor the gaseous fission products of nuclear explosions at remote locations). The Xenon Processing Unit is a free-standing, relatively lightweight, and transportable system that can be interfaced to a variety of sampling and detection systems. It has a relatively inexpensive, rugged, and compact modular (19-inch rack) design that provides easy access to all parts for maintenance and has a low power requirement.

Simultaneous selective detection of organophosphate and phthalate esters using gas chromatography with positive ion chemical ionization tandem mass spectrometry and its application to indoor air and dust.

A selective and sensitive method for the simultaneous determination of 14 organophosphate and six phthalate esters using gas chromatography (GC) and mass spectrometry (MS) is presented. Both of these compound classes are frequently found in the indoor environment due to their use as bulk additives in numerous polymers, consumer products and building materials. GC/MS utilizing positive ion chemical ionisation (PICI) in selected reaction monitoring (SRM) mode with isobutane as the reagent gas was found to be the best of the tested methods; it proved superior to electron ionisation (EI) in selected ion monitoring (SIM) mode and to PICI using methane as the reagent gas. The method was applied to indoor air samples collected by active air sampling using solid-phase extraction (SPE) cartridges. Organophosphates and phthalates were simultaneously determined with method detection limits (MDLs) in the range of 0.1-47 ng m(-3). For most compounds the MDLs were ≤0.2 ng m(-3), but due to the presence of some of these ubiquitous indoor air pollutants in the blanks, significantly higher MDLs were observed for a few compounds. Finally, the method was also applied in the screening of a much more complex sample matrix, indoor dust.

Indoor contamination with hexabromocyclododecanes, polybrominated diphenyl ethers, and perfluoroalkyl compounds: an important exposure pathway for people?

This review underlines the importance of indoor contamination as a pathway of human exposure to hexabromocyclododecanes (HBCDs), polybrominated diphenyl ethers (PBDEs), and perfluoroalkyl compounds (PFCs). There is ample evidence of substantial contamination of indoor dust with these chemicals and that their concentrations in indoor air exceed substantially those outdoors. Studies examining the relationship between body burden and exposure via indoor dust are inconsistent; while some indicate a link between body burdens and PBDE and HBCD exposure via dust ingestion, others find no correlation. Likewise, while concentrations in indoor dust and human tissues are both highly skewed, this does not necessarily imply causality. Evidence suggests exposure via dust ingestion is higher for toddlers than adults. Research priorities include identifying means of reducing indoor concentrations and indoor monitoring methods that provide the most "biologically-relevant" measures of exposure as well as monitoring a wider range of microenvironment categories. Other gaps include studies to improve understanding of the following: emission rates and mechanisms via which these contaminants migrate from products into indoor air and dust; relationships between indoor exposures and human body burdens; relevant physicochemical properties; the gastrointestinal uptake by humans of these chemicals from indoor dust; and human dust ingestion rates.

Determination of organophosphorous flame retardants in fish tissues by matrix solid-phase dispersion and gas chromatography.

Organophosphate esters (OPEs), utilized as flame retarding agents and/or plasticizers, are almost ubiquitous in environmental compartments, and biota and foods could be contaminated by bioaccumulation or during the treatment processes. A multiresidue method is proposed for the determination of 13 OPEs in fish tissues: analytes were simultaneously extracted and purified using the matrix solid phase dispersion technique and then determined by gas chromatography with nitrogen-phosphorus detection. The main parameters affecting extraction yield and selectivity, such as the type of dispersant material, clean-up co-sorbent, rinse and elution solvents, were evaluated to obtain lipid-free extracts and quantitative recoveries for OPEs. Under optimal conditions, 0.5 g of samples was dispersed with 2 g Florisil and 1 g anhydrous sodium sulphate and transferred to a solid phase extraction cartridge containing 1 g alumina. The lipids were removed using 5 mL n-hexane/dichloromethane (1:1) and analytes were recovered with 10 mL n-hexane/acetone (6:4) and directly analysed. The method developed provided recoveries between 70 and 110% for different kinds of fish, and the day-to-day variability was between 1 and 9%. This procedure constitutes the first analytical method for the analysis of OPEs in a food matrix and it is applicable to analyse a large number of samples to evaluate the occurrence and sources of OPEs in biota and foods.

Indoor levels of polycyclic aromatic hydrocarbons in homes with or without wood burning for heating.

The aim of this study was to investigate the impact of domestic wood burning on indoor levels of polycyclic aromatic hydrocarbons (PAHs). Indoor and outdoor concentrations of 27 PAHs were measured during wintertime in homes with (n= 13) or without (n 0) wood-burning appliances and at an ambient site in a Swedish residential area where wood burning for space heating is common. Twenty-four hour indoor levels of anthracene, benzo(ghi)fluoranthene, cyclopenta(cd)pyrene, benz(a)anthracene, chrysene/triphenylene, benzo(a)pyrene (BaP), indeno(1,2,3-cd)pyrene, benzo(ghi)perylene, and coronene were significantly (about 3- to 5-fold) higher in homes with, compared with homes without, wood-burning appliances. The outdoor levels of PAHs were generally higher than the indoor levelsfor all PAHs exceptforthe methylated phenanthrenes. The total PAH cancer potency (sum of BaP equivalents) was significantly higher (about 4 times) in the wood-burning homes compared with the reference homes, with BaP being the largest contributor, while phenanthrene made the largest contribution to the total PAH concentration in indoor and outdoor air. The median indoor BaP level in the wood-burning homes (0.52 ng/m3) was 5 times higher than the Swedish health-based guideline of 0.1 ng/m3, which was also exceeded outdoors on all days (median 0.37 ng/m3).

Organophosphate triesters in indoor environments.

In this study the occurrence of ten organophosphate triesters in indoor air at 29 different locations was investigated. They were detected at all locations and a total of ten compounds were identified. The predominant compounds were the chlorinated compounds tris(chloroisopropyl) phosphate and tris(2-chloroethyl) phosphate with a concentration around 2 microg m(-3) in some indoor environments. A rough estimation gives at hand a daily inhalation of around 10 microg for each of these two compounds.