Electrochemistry of chloramphenicol on laser-induced graphene electrodes and its voltammetric determination in honey.

Laser scribing is a promising technology for the rapid and large-scale production of low-cost electrochemical sensors from diverse substrates. Polyimide has been the most popular so far because of its low cost, flexibility and capability of generating high-quality porous graphene films, known as laser-induced graphene (LIG). Herein we report the electrochemistry of chloramphenicol (CAP) on LIG electrodes and its determination in honey samples. LIG electrodes were fabricated by the photothermal conversion of sp3 carbon within the polymeric matrix into sp2 carbon using a CO2 laser cutter. The LIG electrode associated with differential pulse voltammetry (DPV) showed good linearity (R2 > 0.99) in the range from 10 to 160 µmol L-1 with a limit of detection of 1.0 µmol L-1 and good precision (RSD < 5%) for the electrochemical reduction of CAP species. Detection was possible free from the interference of other antibiotics, such as amoxicillin, tetracycline, sulfanilamide, and sulfamethoxazole. Spiked honey samples were analyzed by the standard-addition method and recovery values between 86 and 109% were obtained, which confirmed the absence of sample matrix effects. Therefore, the proposed sensor is an alternative, feasible, low-cost, and powerful analytical tool for the determination of CAP in honey.

New conductive filament ready-to-use for 3D-printing electrochemical (bio)sensors: Towards the detection of SARS-CoV-2.

The 3D printing technology has gained ground due to its wide range of applicability. The development of new conductive filaments contributes significantly to the production of improved electrochemical devices. In this context, we report a simple method to producing an efficient conductive filament, containing graphite within the polymer matrix of PLA, and applied in conjunction with 3D printing technology to generate (bio)sensors without the need for surface activation. The proposed method for producing the conductive filament consists of four steps: (i) mixing graphite and PLA in a heated reflux system; (ii) recrystallization of the composite; (iii) drying and; (iv) extrusion. The produced filament was used for the manufacture of electrochemical 3D printed sensors. The filament and sensor were characterized by physicochemical techniques, such as SEM, TGA, Raman, FTIR as well as electrochemical techniques (EIS and CV). Finally, as a proof-of-concept, the fabricated 3D-printed sensor was applied for the determination of uric acid and dopamine in synthetic urine and used as a platform for the development of a biosensor for the detection of SARS-CoV-2. The developed sensors, without pre-treatment, provided linear ranges of 0.5-150.0 and 5.0-50.0 µmol L-1, with low LOD values (0.07 and 0.11 µmol L-1), for uric acid and dopamine, respectively. The developed biosensor successfully detected SARS-CoV-2 S protein, with a linear range from 5.0 to 75.0 nmol L-1 (0.38 µg mL-1 to 5.74 µg mL-1) and LOD of 1.36 nmol L-1 (0.10 µg mL-1) and sensitivity of 0.17 µA nmol-1 L (0.01 µA µg-1 mL). Therefore, the lab-made produced and the ready-to-use conductive filament is promising and can become an alternative route for the production of different 3D electrochemical (bio)sensors and other types of conductive devices by 3D printing.

Adsorptive stripping voltammetric determination of chloramphenicol residues in milk samples using reduced graphene oxide sensor.

In this paper, the electrochemical response of chloramphenicol (CHL) was investigated on a bare glassy carbon electrode (GCE) and after modification with reduced graphene oxide (GCE/rGO). Preliminary studies by cyclic voltammetry demonstrated an adsorption-controlled mass transport regime of CHL species and a pH-dependent behavior on both electrode surfaces. An adsorptive stripping differential pulse voltammetry (AdSDPV) method was proposed and under optimized instrumental conditions, a comparison of the analytical characteristics of both sensors was performed. The GCE/rGO sensor showed an increase in sensitivity (10-fold), and an anticipation of the reduction potential (200 mV), compared to the bare electrode, due to the adsorptive character (pre-concentration of the CHL species) and the electrocatalytic effect of the nanomaterial. The method was applied to skimmed and whole milk samples, which were simply diluted (50-fold) in supporting electrolyte. The results by AdSDPV using GCE/rGO showed adequate detectability (0.22 µmol L-1), good precision with a 6% relative standard deviation (RSD) and satisfactory recovery ranging from 93 to 108%. The obtained results were statistically similar (95% confidence level) with those performed through ultra-fast liquid chromatography (UFLC). Furthermore, the sensor showed an improvement in the analytical performance for CHL detection, when compared to other sensors reported in the literature. Therefore, the developed method is reliable and promising for implementation in monitoring CHL residues in milk samples.

Biosensing strategies for the electrochemical detection of viruses and viral diseases - A review.

Viruses are the causing agents for many relevant diseases, including influenza, Ebola, HIV/AIDS, and COVID-19. Its rapid replication and high transmissibility can lead to serious consequences not only to the individual but also to collective health, causing deep economic impacts. In this scenario, diagnosis tools are of significant importance, allowing the rapid, precise, and low-cost testing of a substantial number of individuals. Currently, PCR-based techniques are the gold standard for the diagnosis of viral diseases. Although these allow the diagnosis of different illnesses with high precision, they still present significant drawbacks. Their main disadvantages include long periods for obtaining results and the need for specialized professionals and equipment, requiring the tests to be performed in research centers. In this scenario, biosensors have been presented as promising alternatives for the rapid, precise, low-cost, and on-site diagnosis of viral diseases. This critical review article describes the advancements achieved in the last five years regarding electrochemical biosensors for the diagnosis of viral infections. First, genosensors and aptasensors for the detection of virus and the diagnosis of viral diseases are presented in detail regarding probe immobilization approaches, detection methods (label-free and sandwich), and amplification strategies. Following, immunosensors are highlighted, including many different construction strategies such as label-free, sandwich, competitive, and lateral-flow assays. Then, biosensors for the detection of viral-diseases-related biomarkers are presented and discussed, as well as point of care systems and their advantages when compared to traditional techniques. Last, the difficulties of commercializing electrochemical devices are critically discussed in conjunction with future trends such as lab-on-a-chip and flexible sensors.