Surface roughness and optical characteristics evaluations after chairside adjustment of different zirconia types.

STATEMENT OF PROBLEM: Limited evidence is available for the effect of chairside adjustment using rotary cutting instruments on the surface roughness and optical properties of different zirconia types. PURPOSE: To evaluate the effect of simulated adjustments on surface roughness and optical properties of different zirconia types. MATERIALS AND METHODS: Three Partially Stabilized Zirconia (PSZ) types based on mole percent yttria (Y) concentration from the same manufacturer (Katana; Kuraray) were used: 3Y-PSZ, 4Y-PSZ, and 5Y-PSZ. Thirty disk-shaped specimens (Ø14 × 1.2 mm) from different zirconia types (N = 90) were prepared. Specimens were either left without adjustment (NA), adjusted with Dialite ZR finishing and polishing system (Brasseler) (APol), or adjusted with course diamond instruments only (ADia). The specimens were distributed into 9 groups (n = 10): Group 3Y-PSZ/NA, Group 3Y-PSZ/APol, Group 3Y-PSZ/ADia, Group 4Y-PSZ/NA, Group 4Y-PSZ/APol, Group 4Y-PSZ/ADia, Group 5Y-PSZ/NA, Group 5Y-PSZ/APol, and Group 5Y-PSZ/ADia. The surface roughness of specimen was analyzed using an Atomic Force Microscope (AFM) (Bruker's Dimension Icon, Bruker) and Root Means Square (RMS) were recorded (nm). Surface Gloss (SG), Translucency Parameter (TP), and Contrast Ratio (CR) values of all groups were recorded using an integrating sphere spectrophotometer. Statistical analysis was performed using analysis of variance (ANOVA) and Tukey's multiple comparison tests for pairwise comparisons at p < 0.05 and 95% confidence interval. RESULTS: APol had no effect on the surface roughness (p = 0.88) while ADia had a significant negative effect (p < 0.05) despite the type of zirconia. Out of the three testes optical properties, only SG was negatively affected by ADia for all types of zirconia (p < 0.05). The two adjustment types did not affect the TP of all the tested zirconia (p = 0.91). The CR was not affected by the tested adjustments for all zirconia types (p = 0.726). CONCLUSION: Proper zirconia adjustment following a sequence of burs and polishers can maintain acceptable roughness and optical properties. Adjustment of zirconia with rough diamond can lead to deleterious effects and should be avoided. CLINICAL SIGNIFICANCE: Chairside adjustment of zirconia could lead to rougher surface and unpredictable changes of surface gloss. Therefore, zirconia adjustment should be minimized to the greatest extent possible and a proper protocol should be followed if had to be done.

Clinical and radiographical evaluation of CAD-CAM crowns with and without deep margin elevation: 10-year results.

STATEMENT OF PROBLEM: Current in vitro and short-term clinical studies suggest that deep margin elevation (DME) is a suitable approach to relocate subgingival margins to a supragingival position. However, long-term clinical results are lacking. PURPOSE: The purpose of this retrospective multicenter practice-based study was to assess the long-term clinical performance and periodontal health of teeth restored with computer-aided design and computer-aided manufacturing (CAD-CAM) crowns with or without DME. MATERIAL AND METHODS: Patients who had received CAD-CAM lithium disilicate (LD) crowns with or without DME in 2013 were invited for a follow-up appointment. When indicated, DME had been performed using resin-based restoration. A total of 275 LD crowns had been fabricated chairside, and 151 crowns had been laboratory milled. The crowns had been cemented with 3 different adhesive and self-adhesive resin cements. Clinical and radiographical assessment of the crowns and supporting periodontal structures were performed according to the modified United States Public Health Service (USPHS) criteria. Linear mixed effect models were used to assess the effect of the follow-up time on repeated measurements (α=.05). The Kaplan-Meier survival analyses were determined. RESULTS: A total of 380 patients with 426 crowns (153 with DME and 273 without DME) were examined with a follow-up period of 10 years. Overall, 15 teeth with secondary caries, 4 with loss of vitality, 4 crown fractures, and 3 crowns with lost retention were observed. The DME profile was rated good in 74%, acceptable in 17.5%, and poor in 8.5% of crowns. The periodontal parameters of teeth with DME were not significantly different from teeth without DME (P>.05). The 10-year survival rates for the DME and without DME groups were 95.8% and 94.7%, respectively, while the 10-year success rates for the DME and without DME groups were 94.1% and 93%, respectively. CONCLUSIONS: The use of DME and lithium disilicate crowns as well as adhesive bonding is considered a safe and reliable treatment option. The integrity of periodontal tissue was not affected by the DME or by the crowns.

Zirconia restoration types, properties, tooth preparation design, and bonding. A narrative review.

OBJECTIVE: The purpose of this review was to provide dental professionals with information regarding the various types of zirconia restorations, their mechanical and optical properties, tooth preparation design, and bonding protocol in an effort to enhance the longevity and durability of zirconia restorations. OVERVIEW: The yttria content of zirconia ceramics determines their classification. The mechanical and optical properties of each type are discussed, with an emphasis on the effect of yttria concentration on the properties of zirconia. The processing and sintering methods are also discussed as they have a direct impact on the properties of zirconia. The design of tooth preparation, specifically occlusal reduction, varies depending on the type of zirconia used in each case. Finally, a protocol for zirconia restoration bonding is described to ensure optimal bonding to the tooth structure. CONCLUSION: Not all zirconia restorations are the same. The selection of zirconia type based on yttria concentration, processing and sintering methods, tooth preparation design, and adherence to the bonding protocol are all critical to the success and longevity of zirconia restorations. CLINICAL SIGNIFICANCE: Zirconia restorations are the most commonly used indirect restorative material. The selection of the most appropriate zirconia type based on its yttria content, which determines its strength and translucency, is critical to the success and the longevity of the restoration. Tooth preparation design also influences the strength and translucency of the zirconia. Air-borne particle abrasion, followed by a ceramic primer and resin cement, can ensure a durable bond to the tooth structure.

Er:YAG laser debonding of zirconia and lithium disilicate restorations.

STATEMENT OF PROBLEM: Yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) restorations of different formulations are being used increasingly in monolithic form for a range of clinical applications. Using rotary instruments to remove such restorations for any purpose is challenging, but they can be removed conservatively with erbium lasers. However, studies on how a laser penetrates different zirconias to break the cement bond between the tooth surface and the zirconia are lacking. PURPOSE: The purpose of this in vitro study was to evaluate and compare the time required for an erbium-doped yttrium-aluminum-garnet (Er:YAG) laser to remove different types of zirconia and lithium disilicate crowns. MATERIAL AND METHODS: Forty extracted premolar teeth were prepared, scanned, designed, and milled to fabricate 40 computer-aided design and computer-aided manufacturing (CAD-CAM) crowns, which were assigned to 4 groups (n=10): 3 mol% Y-TZP, 4 mol% Y-TZP, 5 mol% Y-TZP, and lithium disilicate as a control. All crowns were bonded to the teeth with a self-adhesive resin cement (Panavia SA Cement Universal). Each specimen was irradiated with an Er:YAG laser with the following parameters: 300 mJ, 15 Hz, 5.0 W, and a 50-microsecond pulse duration (supershort pulse mode). The irradiation time required for crowns to be retrieved successfully was recorded for each specimen. Data were statistically analyzed using analysis of variance and the Tukey honestly significant difference post hoc test (α=.05). The intaglio surfaces of the restorations were analyzed using scanning electron microscopy (SEM). RESULTS: The mean ±standard deviation times in minutes needed for crown debonding were 12.46 ±4.17 for the 3 mol% Y-TZP group, 10.30 ±3.33 for the 4 mol% Y-TZP group, 4.03 ±1.62 for the 5 mol% Y-TZP group, and 2.08 ±0.92 for the lithium disilicate group. A statistically significant difference (P<.05) in the debonding time was found for all investigated groups, expect between the 3 mol% and 4 mol% Y-TZP groups and between the 5 mol% Y-TZP and lithium disilicate groups. SEM analysis of the ceramic surfaces showed no visual damage associated with Er:YAG laser irradiation. CONCLUSIONS: Zirconia crown retrieval time with the Er:YAG laser was influenced by the yttria content of the zirconia, with decreasing retrieval time with increasing yttria content. Er:YAG laser debonding of zirconia crowns is a noninvasive, efficient, and rapid approach to the removal of crowns and could be applied in clinical practice.

Strength and phase transformation of different zirconia types after chairside adjustment.

STATEMENT OF PROBLEM: Limited evidence is available for the effect of chairside adjustment using diamond instruments on different types of zirconia. PURPOSE: The purpose of this in vitro study was to evaluate the effect of simulated adjustments on the biaxial flexural strength and phase transformation of 3 different zirconia types. MATERIAL AND METHODS: Three zirconia types from the same manufacturer (Katana; Kuraray) were used: High Translucency (3Y-PSZ), Super Translucent Multi Layered (4Y-PSZ), and Ultra Translucent Multi Layered (5Y-PSZ). Thirty disk-shaped specimens (Ø14×1.2 mm) were fabricated according to the International Organization for Standardization (ISO) Standard 6872 from different zirconia types (N=90). Specimens were either left without adjustment (NA), adjusted with Dialite ZR finishing and polishing system (Brasseler) (APol), or adjusted with course diamond instruments only (ADia). The specimens were distributed into 9 groups (n=10): group 3Y-PSZ/NA, group 3Y-PSZ/APol, group 3Y-PSZ/ADia, group 4Y-PSZ/NA, group 4Y-PSZ/APol, group 4Y-PSZ/ADia, group 5Y-PSZ/NA, group 5Y-PSZ/APol, and group 5Y-PSZ/ADia. The biaxial flexural strength of each specimen was measured by using a universal testing machine (Model 4411; Instron) and according to ISO 6872. X-ray diffraction analysis was conducted to quantify the monoclinic phase transformation. Scanning electron microscopy images were obtained to evaluate the fracture pattern. Statistical analysis was performed by using analysis of variance (ANOVA) and Tukey multiple comparison tests for pairwise comparisons (α=.05). RESULTS: The mean biaxial flexural strengths ranked from the highest to the lowest were for 3Y-PSZ, 4Y-PSZ, and 5Y-PSZ under any test condition (P=.007). Chairside adjustment with a diamond instrument significantly decreased the flexural strength of all zirconia types (P<.05). No statistically significant difference was found between the effect of APol and ADia on the strength of zirconia 3Y-PSZ (P=.603), 4Y-PSZ (P=.993), and 5Y-PSZ (P=.660). Phase transformation did not occur in the 5Y-PSZ groups. ADia groups had significantly higher phase transformation values regardless of zirconia type (P<.05). CONCLUSIONS: The biaxial flexural strength of zirconia decreased significantly after chairside adjustment with diamond instruments regardless of the yttria percentage. Adjustment with the Dialite ZR finishing and polishing system caused less tetragonal to monoclinic phase transformation than adjustment with a course-grit diamond instrument.

Effectiveness of CAD/CAM technology: A self-assessment tool for preclinical waxing exercise.

INTRODUCTION: This study assessed the utility of CAD/CAM technology as a self-assessment tool for preclinical waxing compared to traditional student self-assessment to evaluate preclinical work. MATERIAL AND METHODS: Thirty-seven students completed the wax-up of the maxillary left central incisor with the goal of recreating original anatomy and completed a traditional self-assessment. The original, unreduced cast and waxings were scanned with an intraoral scanner (E4D, Planmeca). Using CAD/CAM software (Compare, Planmeca), each waxing was superimposed over the original. Tolerance (250 µm) was set to illustrate under- and over-contoured areas, enabling visualisation of the waxing compared to original in three dimensions. Students then completed another self-assessment and an exit survey. RESULTS: Twenty-four per cent of self-assessment responses changed after using Compare Software. 20% changed from satisfactory to unsatisfactory. Four per cent changed from unsatisfactory to satisfactory. Greatest change in response occurred in the Incisal Edge (49%) rubric category. Interproximal Contact Area (3%) demonstrated least change in response. Seventy per cent strongly agreed that Compare Software enabled more effective assessment of Lingual Contour. Eight per cent strongly disagreed that Compare Software enabled more effective assessment of finishing. DISCUSSION: CAD/CAM software can improve student's critical self-assessment. Different rubric categories demonstrated differing rates of response change, indicating more critical of certain aspects of the waxing. Majority strongly agreed that the software enabled more effective self-assessment. CONCLUSION: CAD/CAM technology enhances student's learning in dental wax-up through improving self-assessment. This technology may improve teacher-student communication, reduce one-on-one teaching time and allow higher student-teacher ratio.

Effects of two Postprocessing Methods onto Surface Dimension of in-Office Fabricated Stereolithographic Implant Surgical Guides.

PURPOSE: To evaluate the effects of two postprocessing methods in terms of the overall, intaglio, and cameo surface dimensions of in-office stereolithographic fabricated implant surgical guides. MATERIALS AND METHODS: Twenty identical implant surgical guides were fabricated using a stereolithographic printer. Ten guides were postprocessed using an automated method. The other ten guides were postprocessed using a series of hand washing in combination with ultrasonics. Each guide was then scanned using cone-beam computed tomography to produce a set of digital imaging and communications in medicine (DICOM) files which were converted into standard tessellation language (STL) files. The STL file was then superimposed onto the original STL design file using the best fit alignment. The average positive and negative surface discrepancy differences in terms of means and variances were analyzed using t-test (α = 0.05). RESULTS: For the alternative group, the average positive and negative overall, intaglio, and cameo surface discrepancies were 77.38 ± 10.68 µm and -67.74 ± 6.55 µm; 78.83 ± 8.65 µm and -68.16 ± 5.26 µm; and 70.5 ± 8.48 µm -64.84 ± 5.55 µm, respectively. For the automated group, the average positive and negative overall, intaglio, and cameo surface discrepancies were 51.88 ± 4.38 µm and -170.7 ± 11.49 µm; 64.3 ± 4.44 µm and -89.45 ± 6.25 µm; and 83.59 ± 4.81 µm and -144.26 ± 13.19 µm, respectively. There was a statistical difference between the means of the two methods for the overall, intaglio, and cameo positive and negative discrepancies (p < 0.001). CONCLUSIONS: For a single implant tooth-supported implant guide, using hand washing with ultrasonics appeared to be consistently better than the automated method. The manual method presented with more positive discrepancies, while the automated method presented with more negative discrepancies.

Fracture Load of Different Zirconia Types: A Mastication Simulation Study.

PURPOSE: To assess the effect of yttria mol% concentration and material thickness on the biaxial fracture load (N) of zirconia with and without mastication simulation. MATERIALS AND METHODS: Disk-shaped specimens (N = 120) of 3 mol% yttria-partially stabilized zirconia, 3Y-PSZ (Katana High Translucent, Kuraray Noritake), 4 mol% yttria-partially stabilized zirconia, 4Y-PSZ (Katana Super Translucent Multi Layered) and 5 mol% Yttria-partially stabilized zirconia, 5Y-PSZ (Katana Ultra Translucent Multi Layered) were prepared to thicknesses of 0.7 and 1.2 mm. For each thickness, the biaxial fracture load (N) was measured with and without mastication simulation with 1.2 million cycles at a 110-N load and simultaneous thermal cycling at 5°C to 55°C. The data were analyzed by three-way Analysis of Variance (α = 0.05) and Tukey-Kramer adjusted multiple comparison test. RESULTS: Yttria mol% concentration and material thickness had a statistically significant effect on the mean biaxial fracture load (F = 388.16, p < 0.001 and F = 714.33, p < 0.001 respectively). The mean biaxial fracture load ranged from the highest to the lowest; 3Y-PSZ, 4Y-PSZ, and 5Y-PSZ (p = 0.012). The mean biaxial fracture load of the 1.2 mm thickness groups was significantly higher than 0.7 mm thickness at any given condition (p = 0.002). Not all specimens survived the mastication simulation protocol. Fifty percent of the 0.7-mm-thick 4Y-PSZ specimens, 70% of the 0.7-mm-thick 5Y-PSZ specimens and 20% of 1.2-mm-thick 5Y-PSZ specimens fractured during mastication simulation. Mastication simulation had no statistically significant effect on the biaxial fracture load (F = 1.24, p = 0.239) of the survived specimens. CONCLUSIONS: Lowering yttria mol% concentration and increasing material thickness significantly increases the fracture load of zirconia. At 0.7 mm thickness, only 3Y-PSZ survived masticatory simulation. A minimum material thickness of 1.2 mm is required for 4Y-PSZ or 5Y-PSZ.

Exploring the use of pulsed erbium lasers to retrieve a zirconia crown from a zirconia implant abutment.

BACKGROUND: Removal of cement-retained implant fixed restorations when needed, can be challenging. Conventional methods of crown removal are time consuming and costly for patients and practitioners. This research explored the use of two different types of pulsed erbium lasers as a non-invasive tool to retrieve cemented zirconia crowns from zirconia implant abutments. MATERIALS AND METHODS: Twenty identical zirconia crowns were cemented onto 20 identical zirconia prefabricated abutments using self-adhesive resin cement. The specimens were divided into two groups for laser assisted crown removal; G1 for erbium-doped yttrium aluminum garnet laser (Er:YAG), and G2 for erbium, chromium-doped yttrium, scandium, gallium and garnet (Er,Cr:YSGG). For the G1, after the first crown removal, the specimens were re-cemented and removed again using the Er:YAG laser. Times needed to remove the crowns were recorded and analyzed using ANOVA (α = 0.05). The surfaces of the crown and the abutment were further examined using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) analyses. RESULTS: The average times of zirconia crown removal from zirconia abutments were 5 min 20 sec and 5 min 15 sec for the Er:YAG laser of first and second experiments (G1), and 5 min 55 sec for the Er,Cr:YSGG laser experiment (G2). No statistical differences were observed among the groups. SEM and EDS examinations of the materials showed no visual surface damaging or material alteration from the two pulsed erbium lasers. CONCLUSIONS: Both types of pulsed erbium lasers can be viable alternatives for retrieving a zirconia crown from a zirconia implant abutment. Despite operating at different wavelengths, the Er:YAG and Er,Cr:YSGG lasers, perform similarly in removing a zirconia crown from a zirconia implant abutment with similar parameters. There are no visual and elemental composition damages as a result of irradiation with pulsed erbium lasers.

Finite element analysis of a one-piece zirconia implant in anterior single tooth implant applications.

This study evaluated the von Mises stress (MPa) and equivalent strain occurring around monolithic yttria-zirconia (Zir) implant using three clinically simulated finite element analysis (FEA) models for a missing maxillary central incisor. Two unidentified patients' cone-beam computed tomography (CBCT) datasets with and without right maxillary central incisor were used to create the FEA models. Three different FEA models were made with bone structures that represent a healed socket (HS), reduced bone width edentulous site (RB), and immediate extraction socket with graft (EG). A one-piece abutment-implant fixture mimicking Straumann Standard Plus tissue level RN 4.1 X 11.8mm, for titanium alloy (Ti) and Zir were modeled. 178 N oblique load and 200 N vertical load were used to simulate occlusal loading. Von Mises stress and equivalent strain values for around each implant model were measured. Within the HS and RB models the labial-cervical region in the cortical bone exhibited highest stress, with Zir having statistically significant lower stress-strain means than Ti in both labial and palatal aspects. For the EG model the labial-cervical area had no statistically significant difference between Ti and Zir; however, Zir performed better than Ti against the graft. FEA models suggest that Ti, a more elastic material than Zir, contributes to the transduction of more overall forces to the socket compared to Zir. Thus, compared to Ti implants, Zir implants may be less prone to peri-implant bone overloading and subsequent bone loss in high stress areas especially in the labial-cervical region of the cortical bone. Zir implants respond to occlusal loading differently than Ti implants. Zir implants may be more favorable in non-grafted edentulous or immediate extraction with grafting.

Intaglio Surface Dimension and Guide Tube Deviations of Implant Surgical Guides Influenced by Printing Layer Thickness and Angulation Setting.

PURPOSE: To measure overall intaglio dimensional and tube deviations of implant guides printed at 50 and 100 µm layer thickness at 0°, 45°, and 90° angulation using a stereolithographic (SLA) printer. MATERIALS AND METHODS: A surgical implant guide design from a subject missing a maxillary right central incisor, used as the original standard tessellation language (STL) were stereolithographically fabricated at each thickness and angulation, 50 and 100 µm layer thickness at 0°, 45°, and 90° angulation (n = 10 each group). The guide was then scanned using cone beam computed tomography. The digital imaging and communications in medicine (DICOM) scanned files were then converted to an STL format. The overall dimensional deviations of the intaglio surface and the positioning of the implant guide tube were then superimposed onto the original designed STL file using best-fitting alignment. A t-test and an F-test as well as ANOVA followed by a post hoc t-test were used to determine statistical significant differences (α = 0.05) for the intaglio surface and guide tube deviation, respectively. RESULTS: The overall intaglio surface discrepancies (µm) printed at 0°, 45°, and 90° were 55.07 ± 1.36, 52.39 ± 2.09, and 61.02 ± 15.96 for 50 µm layer; and 98.38 ± 10.55, 84.47 ± 10.61, and 90.26 ± 5 for 100 µm layer with statistically significant differences for both t-test and F-test, p < 0.001. The maximal guide tube linear deviations (µm) printed at 0°, 45°, and 90° were 10.78 ± 3.84, 8.16 ± 3.68, and 12.57 ± 5.39 for 50 µm layer (ANOVA, p = 0.096); and 10.95 ± 5.23, 16.79 ± 4.97, and 22.63 ± 2.81 for 100 µm layer (ANOVA, p < 0.001). The maximal guide tube angular deviations (°) printed at 0°, 45°, and 90° were 1.29 ± 0.30, 0.64 ± 0.13, and 0.56 ± 0.21 for 50 µm layer (ANOVA, p < 0.001); and 1.57 ± 0.29, 0.86 ± 0.14, and 1.02 ± 0.31 for 100 µm layer (ANOVA, p = 0.034). There was a statistical difference in the deviations between 50 and 100 µm layer printing in all printed angulations except at 0° (t-test, p = 0.05, p = 0.03, and p = 0.001 for 0°, 45°, and 90°) and linear deviations (t-test, p < 0.001, p = 0.009, and p = 0.001 for 0°, 45°, and 90°). CONCLUSION: Printing at 50 µm layer reduces dimensional intaglio deviations in general and reduces tube angular deviations with different angulations of printing. However, the deviations were only ∼60 to 100 µm for the intaglio dimension deviations; and ∼0.04 to 0.26 mm and ∼0.25° to ∼2° for tube deviations.

Zirconia implants with improved attachment to the gingival tissue.

BACKGROUND: Gingival tissue attachment is known to be important for long-term prognosis of implants. This in vitro study evaluated the gingival attachment to zirconia implants and zirconia implants modified with sol-gel derived TiO2 coatings. METHODS: Zirconia endodontic posts (n = 23) were used to function as implants that were inserted into the center of full-thickness porcine gingival explants (n = 31). The tissue/implant specimens were then individually placed at an air/liquid interface on a stainless-steel grid in cell culture wells containing a nutrient solution. The tissue cultures were incubated at 37°C in a 5% CO2 environment and at days 7 and 14, the specimens were harvested and analyzed by dynamic mechanical analysis (DMA) measurements under dynamic loading conditions mimicking natural mastication. Specimens were also analyzed by immunohistochemical staining identifying the laminin (Ln) γ2 chain specific for Ln-332, which is known to be a crucial molecule for the proper attachment of epithelium to tooth/implant surface. RESULTS: Tissue attachment to TiO2 -coated zirconia demonstrated higher dynamic modulus of elasticity and higher creep modulus, meaning that the attachment is stronger and more resistant to damage during function over time. Laminin γ2 was identified in the attachment of epithelium to TiO2 -coated zirconia. CONCLUSIONS: Both DMA and histological analysis support each other, so the gingival tissue is more strongly attached to sol-gel derived TiO2 -coated zirconia than uncoated zirconia. Immunohistochemical staining showed that TiO2 coating may enhance the synthesis and deposition of Ln-332 in the epithelial attachment to the implant surface.

Accuracy and precision of 3D-printed implant surgical guides with different implant systems: An in vitro study.

STATEMENT OF PROBLEM: Implant guided surgery systems promise implant placement accuracy and precision beyond straightforward nonguided surgery. Recently introduced in-office stereolithography systems allow clinicians to produce implant surgical guides themselves. However, different implant designs and osteotomy preparation protocols may produce accuracy and precision differences among the different implant systems. PURPOSE: The purpose of this in vitro study was to measure the accuracy and precision of 3 implant systems, Tapered Internal implant system (BioHorizons) (BH), NobelReplace Conical (Nobel Biocare) (NB), and Tapered Screw-Vent (Zimmer Biomet) (ZB) when in-office fabricated surgical guides were used. MATERIAL AND METHODS: A cone beam computed tomography (CBCT) data set of an unidentified patient missing a maxillary right central incisor and intraoral scans of the same patient were used as a model. A software program (3Shape Implant Studio) was used to plan the implant treatment with the 3 implant systems. Three implant surgical guides were fabricated by using a 3D printer (Form 2), and 30 casts were printed. A total of 10 implants for each system were placed in the dental casts by using the manufacturer's recommended guided surgery protocols. After implant placement, postoperative CBCT images were made. The CBCT cast and implant images were superimposed onto the treatment-planning image. The implant positions, mesiodistal, labiopalatal, and vertical, as well as implant angulations were measured in the labiolingual and mesiodistal planes. The displacements from the planning in each dimension were recorded. ANOVA with the Tukey adjusted post hoc pairwise comparisons were used to examine the accuracy and precision of the 3 implant systems (α=.05). RESULTS: The overall implant displacements were -0.02 ±0.13 mm mesially (M), 0.07 ±0.14 mm distally (D), 0.43 ±0.57 mm labially (L), and 1.26 ±0.80 mm palatally (P); 1.20 ±3.01 mm vertically in the mesiodistal dimension (VMD); 0.69 ±2.03 mm vertically in the labiopalatal dimension (VLP); 1.69 ±1.02 degrees in mesiodistal angulation (AMD); and 1.56 ±0.92 degrees in labiopalatal angulation (ALP). Statistically significant differences (ANOVA) were found in M (P=.026), P (P=.001), VMD (P=.009), AMD (P=.001), and ALP (P=.001). ZB showed the most displacements in the M and vertical dimensions and the least displacements in the P angulation (P<.05), suggesting statistically significant differences among the M, VMD, VLP, AMD, and ALP. NB had the most M variation. ZB had the least P deviation. NB had the fewest vertical dimension variations but the most angulation variations. CONCLUSIONS: Dimensional and angulation displacements of guided implant systems by in-office 3D-printed fabrication were within clinically acceptable limits: <0.1 mm in M-D, 0.5 to 1 mm in L-P, and 1 to 2 degrees in angulation. However, the vertical displacement can be as much as 2 to 3 mm. Different implant guided surgery systems have strengths and weaknesses as revealed in the dimensional and angulation implant displacements.

Fracture rate of 188695 lithium disilicate and zirconia ceramic restorations after up to 7.5 years of clinical service: A dental laboratory survey.

STATEMENT OF PROBLEM: The use of ceramic materials has increased significantly because of high esthetic demands, low costs, and ease of fabrication. Long-term, clinically based evidence is scarce, and laboratory studies have limited relevance in determining clinical durability. PURPOSE: The purpose of this dental laboratory survey was to evaluate the fracture rate of layered and monolithic lithium disilicate and zirconia single crowns and fixed partial dentures after up to 7.5 years of clinical service. MATERIAL AND METHODS: Two commercial dental laboratories with a database system that was able to track the number of remakes because of fracture only were identified. Lithium disilicate restorations (monolithic and layered) were categorized according to restoration type (single crown, fixed partial denture, veneer, and onlay). Zirconia restorations (monolithic and layered) were categorized according to type (single crown, fixed partial denture) and then into anterior or posterior restoration. Restoration remakes due to poor fit, shade, or marginal integrity were excluded from the evaluation. Data were analyzed, and statistical significance was evaluated with chi-square tests (α=.05). RESULTS: A total of 188 695 (51 751 lithium disilicate and 136 944 zirconia) restorations were included in the analysis, with an overall fracture rate of 1.35%. Lithium disilicate monolithic single crowns had a fracture rate of 0.96%, which was significantly lower than that of layered single crowns at 1.26% (P<.05). When the different types of lithium disilicate restorations were compared, fixed partial denture (monolithic and layered) fracture rates were significantly higher than those of single crowns (P<.001). Monolithic zirconia single crowns (0.54%) fractured at a lower rate than layered zirconia single crowns (2.83%) and monolithic fixed partial dentures (1.83%) (P<.001), while layered single crowns (2.83%) had a higher fracture rate than that of layered fixed partial dentures (1.93%) (P<.001). Monolithic anterior and posterior zirconia restorations fractured at a lower rate than layered anterior and posterior zirconia restorations (P<.05). Posterior monolithic zirconia restorations fractured at a lower rate than anterior restorations, while posterior layered zirconia restorations fractured at a higher rate than anterior zirconia restorations (P<.05). CONCLUSIONS: Within the 7.5-year period, restorations fabricated with lithium disilicate and zirconia restorations had relatively low fracture rates. Monolithic restorations fractured at a lower rate than layered restorations.

Using Er:YAG laser to remove lithium disilicate crowns from zirconia implant abutments: An in vitro study.

BACKGROUND: When implants are restored with cement-retained restorations, prosthetic retrievability can be difficult and often requires sectioning using rotary instruments. Sometimes repeated removals of a cement-retained implant crown are needed such as for treatment of peri-implantitis or immediate implant provisionalization. The purpose of this study was to evaluate the effect of erbium-doped yttrium aluminum garnet (Er:YAG) laser as a non-invasive treatment modality to remove lithium disilicate crowns from zirconia implant abutments following long-term cementation, repetitive debonding and re-cementation, and short-term retrieval. MATERIAL AND METHODS: Twenty identical lithium disilicate crowns were cemented onto zirconia prefabricated abutments using composite resin cement. Ten cemented crowns were removed at 48 hours after cementation as a short-term group (ST), while another 10 were removed 6 months after cementation as a long-term group (LT). To mimicking repetitive recementation and retrieval, the LT crowns were then recemented and removed after 48 hours as a long-term recemention (LTR) group. The LTR crowns were then again recemented and removed after 48 hours as a long-term repeated recemention (LTRR) group. Er:YAG laser was used to facilitate the retrieval of these crowns. recorded and analyzed using ANOVA and t-test. The surfaces of the crown and the abutment were further examined using light microscopy and scanning electron microscopy (SEM). Temperature changes of the abutment and crown upto 10 minutes were also measured and statistically analyzed (paired t-test). RESULTS: The average times of crown removal from zirconia abutments were 4 minutes (min) and 42 second (sec) in LT to 3 min 24 sec in LTR, and 3 min 12 sec in LTRR and ST groups. LTR took the longest time to remove, statistically (ANOVA and t-test, p < .001). No statistical differences were observed among the removal times of LTR, LTRR, and ST groups (t-test, p = .246, .246 and 1). SEM examination of the material surface showed no visual surface damaging from treatment with Er:YAG laser. The temperatures during irradiation ranged from 18.4°C to 20°C and 22.2°C to 24.5°C (Paired t-test, p < .0001) for the abutment and the crown during irradiation from 1 min to 10 mins. CONCLUSIONS: Long-term cementation can increase time in lithium disilicate crown removal from zirconia abutment using Er:YAG. Er:YAG laser is a non-invasive tool to remove cement-retained implant prostheses and should be considered as a viable alternative to rotary instruments.

Salivary protein biomarkers associated with orthodontic tooth movement: A systematic review.

OBJECTIVE: Saliva can provide a non-invasive approach to indicate changes in the oral and systemic conditions. Salivary proteomics allows the discovery of new protein biomarkers associated with certain conditions. The effectiveness and physiological effects of orthodontic tooth movement in theory can be measured using salivary protein biomarkers. SETTING AND SAMPLE POPULATION: This study applied a systematic review to analyse current literature to define and summarize salivary biomarkers associated with orthodontic tooth movement identified by mass spectrometry proteomics and other protein detection techniques. MATERIALS AND METHODS: Peer-reviewed articles published through the 15th of November 2018 via the PubMed, EMBASE, Web of Science and Dentistry & Oral Sciences databases were reviewed. Only studies analysing protein biomarkers in saliva samples collected from human subjects associated with orthodontic treatments were included. RESULTS: Out of 482 articles, 7 studies were selected. Sample size ranged from 3 to 72 subjects. Minor variations of unstimulated whole saliva sample collection protocol were noted. Mass spectrometry proteomics and ELISA represented the majority of biomarker discovery and targeting, respectively. Twenty biomarkers were identified or chosen as target biomarkers. CONCLUSION: Salivary proteins may be used to indicate effectiveness of orthodontic treatment and orthognathic treatment as well as adverse treatment consequence, such as root resorption.

TiO2 Coating and UV Photofunctionalization Enhance Blood Coagulation on Zirconia Surfaces.

This in vitro study was designed to evaluate the effect of sol-gel derived TiO2 coating on blood coagulation, blood protein adsorption, and platelet response on zirconia surfaces. Square-shaped zirconia (n=96) (10x10x2 mm) was cut, ground, sintered, and finally cleansed ultrasonically in each of acetone and ethanol for 5 minutes. Three experimental groups (n=32) were fabricated: (a) zirconia coated with sol-gel derived TiO2, (b) zirconia coated with sol-gel derived TiO2 and treated with ultraviolet (UV) irradiation for 1 hour, and (c) non-coated zirconia as control. The coatings were prepared from tetraisopropyl orthotitanate solution by dip-coating. The thrombogenicity of the specimens was evaluated using a whole blood kinetic clotting time method where the extent of blood clotting was evaluated at 10, 20, 30, 40, 50, and 60 minutes (n=4/time point, total n=24/group). Scanning electron microscope images were taken to observe platelet morphologies after 1-hour incubation with platelet-rich plasma (PRP) (n=5/group). Surface characteristics were visualized using atomic force microscopy (n=1/group). Adsorption of plasma proteins and fibronectin on each surface was studied by gel electrophoresis (n=2/group). Significant differences were observed in blood coagulation between the test groups at 20-, 30-, 40-, and 50-minute time points (p<0.005). UV treated TiO2 coated specimens showed fastest blood coagulation followed by TiO2 coated and non-coated specimens. Furthermore, platelets appeared at a higher activation state on coated specimens. Gel electrophoresis revealed no difference in protein adsorption among the experimental groups. In summary, TiO2 coatings promoted blood coagulation, and it was further enhanced by UV treatment, which has the potential to hasten the wound healing process in vivo.

Effect of different treatments on the flexural strength of fully versus partially stabilized monolithic zirconia.

STATEMENT OF PROBLEM: Recent monolithic zirconia materials used for indirect restorations are predominantly fully stabilized zirconia with claims of enhanced optical properties. These restorations may behave differently from the conventional partially stabilized zirconia restorations, which may negatively affect some of the core properties required for restoration success. PURPOSE: The purpose of this in vitro study was to evaluate and compare the effects of staining, airborne-particle abrasion, and artificial aging on the flexural strength of fully and partially stabilized zirconia material. MATERIAL AND METHODS: Each partially stabilized monolithic zirconia (PSZ) and fully stabilized zirconia (FSZ) material and a zirconia core material (control) were prepared as bar-shaped specimens (2×2×25 mm) and divided into 6 groups (n=8/subgroup): regular sintering, vacuum sintering, stained, airborne-particle abrasion, artificially aged regular sintering, and artificially aged vacuum sintering. Critical load to fracture was determined for all groups by using monotonic uniaxial loading in accordance with International Organization for Standardization standard 6872. Data were analyzed using univariate analysis of variance, followed by the Tukey honest significant difference post hoc test (α=.05). RESULTS: The control and PSZ (1034 and 1008 MPa) displayed a significantly higher (P<.05) flexural strength than FSZ (582 MPa). Airborne-particle abrasion significantly (P<.05) enhanced the strength of the control and PSZ (1413 and 1227 MPa) but significantly (P<.05) reduced the flexural strength of the FSZ (442 MPa). Staining, artificial aging, and vacuum sintering had no significant effects on any of the groups. CONCLUSIONS: Fully stabilized zirconia may behave differently from conventional PSZ, especially with regard to airborne-particle abrasion, which may weaken the FSZ. The strength of PSZ is approximately double the strength of FSZ. Both of the zirconia materials showed resistance to artificial aging.

Fracture of layered zirconia restorations at 5 years: A dental laboratory survey.

STATEMENT OF PROBLEM: The use of ceramic restorations has significantly increased in recent years because of their esthetic properties and the high cost of noble metals. However, given the lack of long-term clinical trials and the limitations of in vitro studies, the durability of ceramic restorations is still questionable. PURPOSE: The purpose of this retrospective study was to determine the fracture rate of layered zirconia restorations at up to 5 years of clinical performance by using a dental laboratory survey model. MATERIAL AND METHODS: Data up to 5 years were collected from 2 commercial dental laboratories. Layered zirconia restorations returned to the laboratory for remaking because of failure (fracture) were identified and included. Restorations were categorized as anterior or posterior. Each category was further divided into complete coverage single crowns (SCs) and multiple unit fixed dental prostheses (FDPs). Fracture rates were compared and analyzed using the chi-square test (α=.05). RESULTS: A total of 31594 restoration records were reviewed and included 13419 anterior restorations (10134 SCs and 3285 FDPs) and 18175 posterior restorations (12810 SCs and 5365 FDPs). The overall fracture rate up to 5 years for all restorations (anterior and posterior) was 3.31%. The fracture rates for anterior restorations were less than for posterior restorations. The fracture rates for anterior SCs were approximately half those of the posterior SC fracture rate, and the combined fracture rate (anterior and posterior) was 3.25%. For FDPs, anterior FDPs fractured at a rate similar to that of posterior FDPs. The combined fracture rate (anterior and posterior FDPs) was 3.47%. CONCLUSIONS: Layered zirconia restorations displayed relatively low fracture rates in the relatively short term of 5 years.