Investigation of Roughness, Morphology, and Wettability Characteristics of Biopolymer Composite Coating on SS 316L for Biomedical Applications.

This project aims to create a 316L stainless steel coated with a biocomposite based on chitosan for use in the biomedical industry. To completely coat the material, the dip-coating technique was used to apply plain chitosan, chitosan nanosilver, chitosan biotin, and chitosan-nanosilver-biotin in that order. This coating's surface morphology was investigated with field emission scanning electron microscopy (FESEM). Surface roughness, average size distribution, and 2D and 3D surface tomography were all investigated using scanning probe microscopy and atomic force microscopy (SPM and AFM). The Fourier transform infrared (FTIR) spectroscopy technique was used to quantify changes in functional groups. To evaluate the coated samples' wettability, contact angle measurements were also performed. The chitosan (CS) + nanosilver, CS + biotin, and CS + biotin + nanosilver-coated 316L stainless steel showed roughness values of about 8.68, 4.21, and 3.3 nm, respectively, compared with the neat chitosan coating, which exhibits 12 nm roughness, indicating a strong effect of biotin and nanosilver on surface topography whereas the coating layers were homogenous, measuring around 33 nm in thickness. For CS + nanosilver and CS + biotin, the average size of agglomerates was approximately 444 nm and 355 nm, respectively. The coatings showed adequate wettability for biomedical applications, were homogeneous, and had no cracks. Their contact angles were around 51-75 degrees. All of these results point to the composite coating's intriguing potential for use in biological applications.

Synthesis of a novel antiweathering nanocomposite superhydrophobic room temperature vulcanized (RTV) silicon rubber enhanced with nanosilica for coating high voltage insulators.

A new nanocomposite superhydrophobic of the RTV (room temperature vulcanized) silicon rubber reinforced with a different percentage of nanosilica was prepared by a two-stage sol-gel route to obtain a superhydrophobic surface coating on high voltage glass insulator, preventing the dust-water droplet from adhering to its surface. The cold spraying technique was utilized to build up a thin nanocomposite superhydrophobic layer on the glass insulator containing different percentages of the nanosilica particles, such as 23 wt %, 33 wt %, and 44 wt % with RTV silicon substrate. The synthesized nanocomposite was analyzed using the contact angle, roughness, adhesion, hardness, and dielectric strength tests. Moreover, the prepared RTV silicon rubber/nanosilica superhydrophobic nanocomposite layer was characterized using the field emission scanning electron microscope (FESEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and the particle size analysis test. Based on the results, the nanosilica particles were well-incorporated into the RTV silicon rubber, obtaining an excellent homogenous distribution thin layer on its surface, supporting its capability to be a superior superhydrophobic surface. The results reveal that the RTV silicon rubber/33wt % nanosilica was the best as a superhydrophobic behavior with a contact angle reaching higher than 158° ± 3; also, a significant change in the dielectric strength was obtained to be 25.5 kV (using a speed voltage of 5.0 kV/s). Importantly, the flashover test was also conducted, and it was found that there was a significant change in the leak current between the coated and uncoated samples. The leak current of the coated sample with a superhydrophobic nanocomposite was reduced to 2.5 mA, while the uncoated sample became 3.2 mA using a voltage load value of 60 kV. The results presented here may improve the nanocomposite material as an antiweathering superhydrophobic thin layer supported by the prepared nano-SiO2 particles against the dust-water droplets which may be adhesive to the high voltage glass insulator.

Graphene preparation and graphite exfoliation.

The synthesis of Graphene is critical to achieving its functions in practical applications. Different methods have been used to synthesis graphene, but graphite exfoliation is considered the simplest way to produce graphene and graphene oxide. In general, controlling the synthesis conditions to achieving the optimum yield, keeping the pristine structure to realize on-demand properties, minimum layers with the smallest lateral size, and minimum oxygen content are the most obstacles experienced by researchers. Each application requires a specific graphene model, graphene oxides GO, or even graphene intercalated compounds (GIC) depending on synthesis conditions and approach. This paper reviewed and summarized the most researches in this field and focusing on exfoliation methods.