The C-shaped root canal systems in mandibular second molars in an Emirati population.

Our study aimed to describe the root and canal morphology of mandibular second molars in Emirati population and to study the prevalence and types of morphological change in C-shaped canal configuration along the root length in an effort to describe C-shaped molars as a unit. Cone beam computed tomography (CBCT) scans of Emirati patients were analyzed in multiple plans and root and canal configuration of mandibular second molars were evaluated. Moreover, specific types of morphological change in C-shaped canal configuration along root length were studied and reconstructed using 3D reconstruction software. A total of 508 mandibular second molars were evaluated. Among the non-C-shaped mandibular second molars, two separate roots were the most prevalent root morphology (78.3%). The mesial root's most common root canal configuration was Vertucci Type II (46.5%), and in the distal root, Vertucci Type I (90.5%). The prevalence of C-shaped mandibular second molars was 17.9% and was significantly prevalent (P < 0.001) in females. Specific types of morphological change in C-shaped molars along the root length were observed and described for the first time, in which the most common types of morphological change were C1-C2-C3d (18%), C1-C3c-C3d (15.4%), C4-C3c-C3d (7.7%), and C3c-C3c-C3d (7.7%). This study showed wide variations in the root and canal morphology in mandibular second molars in Emirati population with a relatively high prevalence of C-shaped canal configuration (17.9%). Moreover, specific types of morphological change in C-shaped configuration were detected and described for the first time in this population.

Effect of repetitive pecking at working length for glide path preparation using G-file.

OBJECTIVES: Glide path preparation is recommended to reduce torsional failure of nickel-titanium (NiTi) rotary instruments and to prevent root canal transportation. This study evaluated whether the repetitive insertions of G-files to the working length maintain the apical size as well as provide sufficient lumen as a glide path for subsequent instrumentation. MATERIALS AND METHODS: The G-file system (Micro-Mega) composed of G1 and G2 files for glide path preparation was used with the J-shaped, simulated resin canals. After inserting a G1 file twice, a G2 file was inserted to the working length 1, 4, 7, or 10 times for four each experimental group, respectively (n = 10). Then the canals were cleaned by copious irrigation, and lubricated with a separating gel medium. Canal replicas were made using silicone impression material, and the diameter of the replicas was measured at working length (D0) and 1 mm level (D1) under a scanning electron microscope. Data was analysed by one-way ANOVA and post-hoc tests (p = 0.05). RESULTS: The diameter at D0 level did not show any significant difference between the 1, 2, 4, and 10 times of repetitive pecking insertions of G2 files at working length. However, 10 times of pecking motion with G2 file resulted in significantly larger canal diameter at D1 (p < 0.05). CONCLUSIONS: Under the limitations of this study, the repetitive insertion of a G2 file up to 10 times at working length created an adequate lumen for subsequent apical shaping with other rotary files bigger than International Organization for Standardization (ISO) size 20, without apical transportation at D0 level.

Torsional and cyclic fatigue resistances of glide path preparation instruments: G-file and PathFile.

This study aimed to compare cyclic fatigue and torsional resistances of glide path creating instruments with different tapers and tip sizes. Two sizes (G1 and G2) from G-File system and three sizes (PathFile #1, #2, and #3) from PathFile system were used for torsional resistance and cyclic fatigue resistance tests (n = 10). The torsional resistance was evaluated at 2-, 3-, 4-, 5-, and 6-mm from the file tip by plotting the torsional load changes until fracture by rotational loading of 2 rpm. The cyclic fatigue resistance was compared by measuring the number of cycles to failure. Data were analyzed statistically using one-way ANOVA and Duncan's post-hoc comparison. The length of the fractured file fragment was also measured. All fractured fragments were observed under a scanning electron microscope (SEM). Although G-2 file showed a lower torsional strength than PathFile #3 at 2- and 3-mm levels (p < 0.05), they had similar ultimate strengths at 4-, 5-, and 6-mm levels (p > 0.05). The smaller files of each brand had a significantly higher cyclic fatigue resistance than the bigger ones (p < 0.05). PathFile #1 and #2 had higher fatigue resistances than G-files (p < 0.05). While G-1 had a similar fatigue resistance as PathFile #3, G-2 showed the lowest and PathFile #1 showed the highest resistances among the tested groups (p < 0.05). The SEM examination showed typical appearances of cyclic fatigue and torsional fractures, regardless of the tested levels. Clinicians may consider the instruments' sizes for each clinical case in order to get efficient glide path with minimal risk of fracture.