Impact on Glycemic Variation Caused by a Change in the Dietary Intake Sequence.

This work presents an analysis of the effect on glycemic variation caused by modifying the macronutrient intake sequence in a person without a diagnosis of diabetes. In this work, three types of nutritional studies were developed: (1) glucose variation under conditions of daily intake (food mixture); (2) glucose variation under conditions of daily intake modifying the macronutrient intake sequence; (3) glucose variation after a modification in the diet and macronutrient intake sequence. The focus of this research is to obtain preliminary results on the effectiveness of a nutritional intervention based on the modification of the sequence of macronutrient intake in a healthy person during 14-day periods. The results obtained corroborate the positive effect on the glucose of consuming vegetables, fiber, or proteins before carbohydrates, decreasing the peaks in the postprandial glucose curves (vegetables: 113-117 mg/dL; proteins: 107-112 mg/dL; carbohydrates: 115-125 mg/dL) and reducing the average levels of blood glucose concentrations (vegetables: 87-95 mg/dL; proteins: 82-99 mg/dL; carbohydrates: 90-98 mg/dL). The present work demonstrates the preliminary potential of the sequence in the macronutrient intake for the generation of alternatives of prevention and solution of chronic degenerative diseases, improving the management of glucose in the organism and permeating in the reduction of weight and the state of health of the individuals.

Dynamic of Glucose Homeostasis in Virtual Patients: A Comparison between Different Behaviors.

This work presents a mathematical model of homeostasis dynamics in healthy individuals, focusing on the generation of conductive data on glucose homeostasis throughout the day under dietary and physical activity factors. Two case studies on glucose dynamics for populations under conditions of physical activity and sedentary lifestyle were developed. For this purpose, two types of virtual populations were generated, the first population was developed according to the data of a total of 89 physical persons between 20 and 75 years old and the second was developed using the Monte Carlo approach, obtaining a total of 200 virtual patients. In both populations, each participant was classified as an active or sedentary person depending on the physical activity performed. The results obtained demonstrate the capacity of virtual populations in the generation of in-silico approximations similar to those obtained from in-vivo studies. Obtaining information that is only achievable through specific in-vivo experiments. Being a tool that generates information for the approach of alternatives in the prevention of the development of type 2 Diabetes.

Monitoring and control interface based on virtual sensors.

In this article, a toolbox based on a monitoring and control interface (MCI) is presented and applied in a heat exchanger. The MCI was programed in order to realize sensor fault detection and isolation and fault tolerance using virtual sensors. The virtual sensors were designed from model-based high-gain observers. To develop the control task, different kinds of control laws were included in the monitoring and control interface. These control laws are PID, MPC and a non-linear model-based control law. The MCI helps to maintain the heat exchanger under operation, even if a temperature outlet sensor fault occurs; in the case of outlet temperature sensor failure, the MCI will display an alarm. The monitoring and control interface is used as a practical tool to support electronic engineering students with heat transfer and control concepts to be applied in a double-pipe heat exchanger pilot plant. The method aims to teach the students through the observation and manipulation of the main variables of the process and by the interaction with the monitoring and control interface (MCI) developed in LabVIEW©. The MCI provides the electronic engineering students with the knowledge of heat exchanger behavior, since the interface is provided with a thermodynamic model that approximates the temperatures and the physical properties of the fluid (density and heat capacity). An advantage of the interface is the easy manipulation of the actuator for an automatic or manual operation. Another advantage of the monitoring and control interface is that all algorithms can be manipulated and modified by the users.

Virtual estimator for piecewise linear systems based on observability analysis.

This article proposes a virtual sensor for piecewise linear systems based on observability analysis that is in function of a commutation law related with the system's outpu. This virtual sensor is also known as a state estimator. Besides, it presents a detector of active mode when the commutation sequences of each linear subsystem are arbitrary and unknown. For the previous, this article proposes a set of virtual estimators that discern the commutation paths of the system and allow estimating their output. In this work a methodology in order to test the observability for piecewise linear systems with discrete time is proposed. An academic example is presented to show the obtained results.

Simplified interval observer scheme: a new approach for fault diagnosis in instruments.

There are different schemes based on observers to detect and isolate faults in dynamic processes. In the case of fault diagnosis in instruments (FDI) there are different diagnosis schemes based on the number of observers: the Simplified Observer Scheme (SOS) only requires one observer, uses all the inputs and only one output, detecting faults in one detector; the Dedicated Observer Scheme (DOS), which again uses all the inputs and just one output, but this time there is a bank of observers capable of locating multiple faults in sensors, and the Generalized Observer Scheme (GOS) which involves a reduced bank of observers, where each observer uses all the inputs and m-1 outputs, and allows the localization of unique faults. This work proposes a new scheme named Simplified Interval Observer SIOS-FDI, which does not requires the measurement of any input and just with just one output allows the detection of unique faults in sensors and because it does not require any input, it simplifies in an important way the diagnosis of faults in processes in which it is difficult to measure all the inputs, as in the case of biologic reactors.