RESUMO
Smart hydrogels are promising materials for actuators and sensors, as they can respond to small changes in their environment with a large property change. Hydrogels can respond to a variety of stimuli, for example temperature, pH, metal ions, etc. In this article, the synthesis and characterization of polyampholyte hydrogels based on open chain ligands showing pH and metal ion sensitivity are described. Copolymer and terpolymer gels using different mixtures of monomers i.e., N-[2-(dimethylaminoethyl)acrylamide] (DMAEAAm), N,N-dimethylacrylamide (DMAAm), acrylic acid (AA) and 2-acrylamido-2-methyl-1-propanesulphonic acid (AMPS), have been synthesized. The effect of copolymer composition, i.e., the ratio and amount of ionic monomers and the degree of crosslinking on the swelling characteristics, was evaluated as a function of pH. On this basis, metal ion sensitivity measurements were performed at selected pH values. The metal ion sensitivity was measured by varying the concentration of Cu2+, Zn2+ and Ag⺠ions under acidic pH conditions.
RESUMO
Novel interpenetrating polymer network (IPN) nanogels composed of poly(acrylic acid) and gelatin were synthesised by one pot inverse miniemulsion (IME) technique. This is based on the concept of nanoreactor and cross-checked from template polymerization technique. Acrylic acid (AA) monomer stabilized around the gelatin macromolecules in each droplet was polymerized using ammonium persulfate (APS) and tetramethyl ethylene diamine (TEMED) in 1:5 molar ratio and cross-linked with N,N-methylene bisacrylamide (BIS) to form semi-IPN (sIPN) nanogels, which were sequentially cross-linked using glutaraldehyde (Glu) to form IPNs. Span 20, an FDA approved surfactant was employed for the formation of homopolymer, sIPN and IPN nanogels. Formation of stable gelatin-AA droplets were observed at 2% surfactant concentration. Dynamic light scattering (DLS) and scanning electron microscopy (SEM) studies of purified nanogels showed small, spherical IPN nanogels with an average diameter of 255 nm. In contrast, sIPN prepared using the same method gave nanogels of larger size. Fourier-transform infrared (FT-IR) spectroscopy, SEM, DLS, X-ray photoelectron spectroscopy (XPS) and zeta potential studies confirm the interpenetration of the two networks. Leaching of free PAA chains in sIPN upon dialysis against distilled water leads to porous nanogels. The non-uniform surface of IPN nanogels seen in transmission electron microscopy (TEM) images suggests the phase separation of two polymer networks. An increase of N/C ratio from 0.07 to 0.17 (from PAA gel to IPN) and O/C ratio from 0.22 to 0.37 (from gelatin gel to IPN) of the nanogels by XPS measurements showed that both polymer components at the nanogel surface are interpenetrated. These nanogels have tailoring properties in order to use them as high potential drug delivery vehicles for cancer targeting.
Assuntos
Resinas Acrílicas/química , Gelatina/química , Nanotecnologia , Polietilenoglicóis/química , Polietilenoglicóis/síntese química , Polietilenoimina/química , Polietilenoimina/síntese química , Emulsões/química , Concentração de Íons de Hidrogênio , Nanogéis , Tamanho da Partícula , Propriedades de SuperfícieRESUMO
Stimuli-responsive hydrogels are materials with great potential for development of active functionalities in fluidics and micro-fluidics. Based on the current state of research on pH sensors, hydrogel sensors are described qualitatively and quantitatively for the first time. The review introduces the physical background of the special properties of stimuli-responsive hydrogels. Following, transducers are described which are able to convert the non-electrical changes of the physical properties of stimuli-responsive hydrogels into an electrical signal. Finally, the specific sensor properties, design rules and general conditions for sensor applications are discussed.
RESUMO
We present a novel method for the fabrication of one-dimensional (1-D) self-assembled monolayers and multilayers (SAMs) of (12-pyrrol-1-yl-dodecyl)-phosphonic acid (Py-DPA) on various polar surfaces using polyelectrolyte nanostructures as positive templates. Particularly, we demonstrate that (i) patterns of aligned 1-D polycation structures on a poly(dimethylsiloxane) stamp can be prepared by moving a droplet of polycation solution along the surface; (ii) these patterns can be used as templates for the ordered assembly of Py-DPA in water where Py-DPA carries a charge opposite to the charge of the template; and (iii) Py-DPA SAMs can then be transferred onto mica or silicon wafers by a printing process. These nanostructures with a polymerizable pyrrole headgroup might be useful for the creation of electrically conductive patterns of conjugated polymers.
RESUMO
Polystyrene nanoparticles with grafted chains of an amino functionalized polymer were prepared by a two-step polymerization process. In the first step, the polystyrene seed particles were synthesized by the conventional batch emulsion polymerization using terpolymer HAS (hydroperoxide monomer, acrylic acid, and styrene) as a surface-active initiator. The surface of the obtained particles contains carboxyl groups, which are responsible for the latex stability, and residual undecomposed hydroperoxide groups. Therefore, in the second step, an amino functional monomer was grafted onto the hydroperoxide modified polystyrene particles by a "grafting from" approach. X-ray photoelectron spectroscopy, NMR, and scanning electron microscopy were used to examine the surface of the amino functionalized particles. The amount of incorporated amino groups onto the particles was determined by fluorescenometric titration. In general, the number of amino groups on the particle surface increased with the increase of the functional monomer content in the reaction mixture. The incorporation of the functional monomer was also confirmed by electrophoretic measurements. Final particles possess amphoteric character due to the presence of amino and carboxyl groups on the surface. Adsorption of human immunoglobulins G onto the amino functionalized particles was studied as a function of pH and ionic strength. The covalent binding of human IgG was performed using the glutaraldehyde preactivation method. The immunoreactivity of the latex-IgG complex was examined by the latex agglutination test.
RESUMO
New injectable, in situ curable liquid formulations consisting of biodegradable aliphatic polyester, i.e., poly(3-allyloxy-1,2-propylene)succinate (PSAGE), methyl methacrylate (MMA), and hydrophilic oligo(ethylene glycol) dimethacrylates (OEGDMA) were investigated. The effect of MMA/OEGDMA ratio, OEGDMA molecular weight, i.e., the length of oligooxyethylene fragments, on the maximum curing temperature, setting time, compressive strength and modulus of the cured materials as well as their hydrophilicity were examined. The latter was characterized by determination of equilibrium water content and static water contact angle. The maximum temperature during crosslinking was found to decrease with increasing OEGDMA molecular weight and decreasing MMA/OEGDMA ratio. The setting time was affected strongly by the concentration of double bonds and was rapidly shortened with its increase. The compressive strength and compressive modulus values decreased with increasing OEGDMA molecular weight and decreasing MMA/OEGDMA ratio. Poly(3-allyloxy-1,2-propylene succinate).