RESUMO
Polymer composites based on poly(N,N'-bis-4-butylphenyl-N,N'-bisphenyl)benzidine (poly-TPD) with PCBM and copper(II) pyropheophorbide derivative (Cu-PP) were developed. In thin films of the poly-TPD and Cu-PP composites, the charge carrier mobility was investigated for the first time. In the ternary poly-TPD:PCBM:Cu-PP composite, the electron and hole mobilities are the most balanced compared to binary composites and the photoconductivity is enhanced due to the sensitization by Cu-PP in blue and red spectral ranges. The new composites are promising for use in the development of photodetectors.
RESUMO
Cu (II) protoporphyrin Cu-PP-IX and chlorin Cu-C-e6 were found to have both thin solid film formation and charge carrier transport abilities. In the layers deposited by resistive thermal evaporation, the mobilities of holes and electrons are on the order of 10-5 cm2 V-1 s-1. Organic light-emitting diodes incorporating the dye molecules as emitting dopants demonstrate electroluminescence in the UV and near-IR ranges.
Assuntos
Porfirinas , Protoporfirinas , Cobre , ElétronsRESUMO
Luminescent temperature sensors are of great interest because they allow remote determination of temperature in transparent media, such as living tissues, as well as on scattering or transparent surfaces of materials. This study analyzes the luminescent properties of copper(II) etioporphyrinate (Cu-EtioP) in a polystyrene film upon variation of temperature from -195 °C to +65 °C in a cryostat. It is shown that the ratio of intensities of phosphorescence transitions in the red spectral region of such a material varies significantly, that is, the material has thermosensory properties. The phosphorescence decay curves of copper(II) etioporphyrinate in a polystyrene film are analyzed. The quantum yield of phosphorescence of copper(II) etioporphyrinate determined by the absolute method was 3.15%. It was also found that the electroluminescence (EL) spectra of copper(II) etioporphyrinate in a poly(9-vinylcarbazole) (PVK) matrix demonstrated a similar change in the spectra in the temperature range -3 °C to +80 °C. That is, copper(II) etioporphyrinate can also be used as a luminescent temperature sensor as part of an active OLED layer.
Assuntos
Cobre , Poliestirenos , Luminescência , TemperaturaRESUMO
Studies on copper(II) tetrafluorenyl porphyrinate (CuTFP) and copper(II) tetraphenyl porphyrinate (CuTPP) have been focused on the charge carrier transport in their solid films and electroluminescence of their composites. In the dye layers deposited by resistive thermal evaporation, the mobilities of holes and electrons are on the order of 10-5 and 10-6 cm2 V-1 s-1 for the charge transport under the influence of traps, and the charge mobility reaches the order of 10-3 cm2 V-1 s-1 at space-charge-limited current in the nontrapping mode. For the dye molecules, the correlation between the mobility of charge carriers and the distribution of the electron density on the highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO), which serve as hopping sites for holes and electrons, respectively, is considered. Organic light-emitting diodes incorporating the dye molecules as emitting dopants demonstrate electroluminescence in the near-infrared (IR) range.
RESUMO
Three new benzothiadiazole (BTD)-containing luminophores with different configurations of aryl linkers have been prepared via Pd-catalyzed cross-coupling Suzuki and Buchwald-Hartwig reactions. Photophysical and electroluminescent properties of the compounds were investigated to estimate their potential for optoelectronic applications. All synthesized structures have sufficiently high quantum yields in film. The BTD with aryl bridged carbazole unit demonstrated the highest electrons and holes mobility in a series. OLED with light-emitting layer (EML) based on this compound exhibited the highest brightness, as well as current and luminous efficiency. The synthesized compounds are not only luminophores with a high photoluminescence quantum yield, but also active transport centers for charge carriers in EML of OLED devices.
RESUMO
Controlled self-assembly and rapid disintegration of supramolecular nanowires is potentially useful for ecology-friendly organic electronics. Herein, a novel method exploiting the binding between crown-substituted double-decker lanthanide phthalocyaninates (ML2, M = Lu, Ce, Tb) and K+ ions is applied for the one-step fabrication of macroscopically long conductive one-dimensional quasi-metal-organic frameworks. Their properties are controlled by the size of the lanthanide ion guiding the assembly through either intra- or intermolecular interactions. A LuL2 linker with a small interdeck distance yields fully conjugated intermolecular-bonded K+-LuL2 nanowires with a thickness of 10-50 nm, a length of up to 50 µm, and a conductivity of up to 11.4 S cm-1, the highest among them being reported for phthalocyanine assemblies. The large size of CeL2 and TbL2 leads to the formation of mixed intra- and intermolecular K+-ML2 phases with poor electric properties. A field-assisted method is developed to deposit aligned conductive K+-LuL2 assemblies on solids. The solid-supported nanowires can be disintegrated into starting components in a good aprotic solvent for further recycling.
RESUMO
An efficient protocol was developed for the synthesis of π-extended isocoumarins and polycyclic aromatic hydrocarbons based on the oxidative coupling of aromatic carboxylic acids with internal alkynes catalyzed by (cyclopentadienyl)rhodium complexes. The coupling chemoselectivity strongly depends on whether Cp or the methylated Cp* ligands are used. The pentamethyl derivative [Cp*RhCl2 ]2 predominantly gives isocoumarins, while the non-methylated complex [CpRhI2 ]n produces naphthalene derivatives. The polyaromatic carboxylic acids (such as 1-naphthoic acid, 1-pyrenecarboxylic acid, fluorene-1-carboxylic acid, and dibenzofuran-4-carboxylic acid) are suitable for this approach. A mixture of Cp*H/RhCl3 can be used as a catalyst instead of [Cp*RhCl2 ]2 . The structures of 3,4-diphenylindeno[1,2-h]isochromen-1(11H)-one and 7,10-dimethyl-8,9-diphenylbenzo[pqr]tetraphene were determined by X-ray diffraction. In addition, the optical properties of the prepared compounds were studied. 7,8-Diphenyl-10H-phenaleno[1,9-gh]isochromen-10-one was employed as an emissive layer for OLED manufacturing. The OLED emits yellow-green light with a maximum intensity 1740â cd â m-2 at 15â V.
RESUMO
The targeted design of lanthanide-based emitters for solution-processed organic light-emitting diodes (OLEDs) resulted in obtaining an NIR OLED with one of the highest efficiencies among ytterbium-based solution-processed OLEDs (30 µW W-1). The design was aimed at the combination of high luminescence efficiency with solubility and charge carrier mobility. The latter was achieved thanks to the introduction of the purposefully selected neutral ligands, which combine electron mobility and the ability to sensitize lanthanide luminescence. Besides, the HOMO and LUMO energies and charge carrier mobility of solution-processed thin films of coordination compounds were measured experimentally for the first time, and novel highly luminescent europium-based materials with PLQYs of up to 80% and purely NIR luminescent ytterbium complexes were obtained.