Novel composites of activated carbon and layered double oxide for the removal of sulfate from synthetic and brackish groundwater.

Sulfate (SO42-) is a major water and environmental concern that causes severe diarrhea, death of invertebrates and plant species, and clogging of industrial pipes. In the current work, treatment of SO42- from synthetic and real groundwater having 3901 mg(SO42-)/L was investigated for the first time using Zn-Al and Mg-Al layered double oxides doped granular activated carbon (GAC/Mg-Al LDO and GAC/Zn-Al LDO). The co-precipitation method was followed to synthesize the GAC/LDO composites using an Mg or Zn to Al molar ratio of 3:1. The GAC/Mg-Al LDO possessed a higher specific surface area (323.9 m2/g) compared to GAC/Zn-Al LDO (195.1 m2/g). The GAC/Mg-Al LDO demonstrated more than 99% removal of SO42- from synthetic water, while it was 50.9% for GAC/Zn-Al LDO and less than 1% for raw GAC at an initial concentration of 50 mg/L. The GAC/Mg-Al LDO was selected for further batch experiments and modeling investigation. The equilibrium data followed the Redlich-Peterson and Langmuir models with determination coefficients of 0.943 and 0.935, respectively. The maximum Langmuir adsorption capacity was 143.5 mg/g. In the real groundwater adsorption study, the screening experiment revealed high selectivity towards SO42- with 62% removal efficiency. The optimum dosage was found to be 50 g/L with an uptake capacity of 61.5 mg/g. The kinetic data of SO42- removal from synthetic and brackish water were in excellent agreement with the pseudo-second order model, and the equilibrium was attained in 5 h. Accordingly, it can be concluded that the GAC/Mg-Al LDO is an efficient material for treating SO42- from real groundwater and can be utilized as a pretreatment unit for high sulfate water resources.

Oxidized carbide-derived carbon as a novel filler for improved antifouling characteristics and permeate flux of hybrid polyethersulfone ultrafiltration membranes.

Polyethersulfone (PES) is a widely used polymer for ultrafiltration (UF) membrane fabrication. In the current study, carbide-derived carbon (CDC) oxidized by acid treatment was utilized as a filler to fabricate a novel PES composites UF membranes. The successful oxidation of CDC was validated from presence of oxygen containing functional groups and improved oxygen content, from 5.08 at.% for CDC to 26.22 at.% for oxidized CDC (OCDC). The OCDC PES UF membranes were prepared at different loadings of OCDC between 0.5 and 3.0 wt%. The membrane porosity, pore size and surface free energy found to be improved while a noticeable reduction in water contact angle was observed with OCDC loading implying the improved hydrophilicity of PES membranes. Consequently, the pure water flux found to improve from 151.6 to 569.6 (L/(m2. h)) for the 3.0 wt% modified OCDC membrane (M-3) which is 3.8 folds of the bare PES membrane. The antifouling characteristics were evaluated by humic acid (HA) filtration. The results revealed a significant enhancement in HA rejection with OCDC loading, the highest rejection was 96.8% for M-3 membrane. Additionally, the adsorption capacity of OCDC modified membranes found to decrease with OCDC loading indicating improved rejection of HA from the membrane surface. Moreover, M-3 demonstrated the maximum flux recovery ratio (FRR) of 92.3%. Reusability of the fabricated membranes was evaluated by deionized water/humic acid cycling filtration. The FRR was higher than 86.7% over three cycles of pure water/HA filtration for 140 min, indicated the excellent stability and reusability of the membranes. Overall, the OCDC was an effective filler for enhancing the PES UF membranes antifouling and permeability properties.

Facile Coaxial Electrospinning Synthesis of Polyacrylonitrile/Cellulose Acetate Nanofiber Membrane for Oil-Water Separations.

Oil-contaminated water and industrial oily wastewater discharges have adversely affected aquatic ecosystems and human safety. Membrane separation technology offers a promising solution for effective oil-water separation. Thus, a membrane with high surface area, hydrophilic-oleophobic properties, and stability is a promising candidate. Electrospinning, a straightforward and efficient process, produces highly porous polymer-based membranes with a vast surface area and stability. The main objective of this study is to produce hydrophilic-oleophobic polyacrylonitrile (PAN) and cellulose acetate (CA) nanofibers using core-shell electrospinning. Incorporating CA into the shell of the nanofibers enhances the wettability. The core PAN polymer improves the electrospinning process and contributes to the hydrophilicity-oleophobicity of the produced nanofibers. The PAN/CA nanofibers were characterized by Fourier transform infrared spectroscopy, field emission scanning electron microscopy, X-ray diffraction, and surface-wetting behavior. The resulting PAN/cellulose nanofibers exhibited significantly improved surface-wetting properties, demonstrating super-hydrophilicity and underwater superoleophobicity, making them a promising choice for oil-water separation. Various oils, including gasoline, diesel, toluene, xylene, and benzene, were employed in the preparation of oil-water mixture solutions. The utilization of PAN/CA nanofibers as a substrate proved to be highly efficient, confirming exceptional separation efficiency, remarkable stability, and prolonged durability. The current work introduces an innovative single-step fabrication method of composite nanofibers, specially designed for efficient oil-water separation. This technology exhibits significant promise for deployment in challenging situations, offering excellent reusability and a remarkable separation efficiency of nearly 99.9%.

A Comparative Analysis of the Effect of Carbonaceous Nanoparticles on the Physicochemical Properties of Hybrid Polyethersulfone Ultrafiltration Membranes.

Numerous studies have been previously reported on the use of nanoscale carbonaceous fillers, such as multi-walled carbon nanotubes (MWCNTs) and graphene oxide (GO), in polymeric ultrafiltration (UF) membranes; however, no insight has been clearly reported on which material provides the best enhancements in membrane performance. In this study, a comparative analysis was carried out to establish a comprehensible understanding of the physicochemical properties of hybrid polyethersulfone (PES) UF membranes incorporated with MWCNTs and GO nanoparticles at various concentrations. The hybrid membranes were prepared via the non-solvent-induced phase separation process and further characterized by field emission scanning electron microscopy and atomic force microscope (AFM). The AFM images showed homogeneous membrane surfaces with a reduction in the membrane surface roughness from 2.62 nm for bare PES to 2.39 nm for PES/MWCNTs and to 1.68 nm for PES/GO membranes due to improved hydrophilicity of the membranes. Physicochemical properties of the hybrid PES membranes were assessed, and the outcomes showed an enhancement in the porosity, pore size, water contact angle, and water permeability with respect to nanoparticle concentration. GO-incorporated PES membranes exhibited the highest porosity, pore size, and lowest contact angle as compared to PES/MWCNTs, indicating the homogeneous distribution of nanoparticles within the membrane structure. PES/MWCNTs (0.5 wt.%) and PES/GO (1.0 wt.%) hybrid membranes exhibited the highest water flux of 450.0 and 554.8 L m-2 h-1, respectively, at an applied operating pressure of 1 bar. The filtration and antifouling performance of the PES hybrid membranes were evaluated using 50 mg L-1 of humic acid (HA) as a foulant at pH = 7. Compared to the bare PES membrane, the MWCNTs and GO-incorporated PES hybrid membranes exhibited enhanced permeability and HA removal. Moreover, PES/MWCNTs (0.5 wt.%) and PES/GO (1 wt.%) hybrid membranes reported HA rejection of 90.8% and 94.8%, respectively. The abundant oxygen-containing functional groups in GO-incorporated PES membranes resulted in more hydrophilic membranes, leading to enhanced permeability and fouling resistance. The antifouling properties and flux recovery ratio were improved by the addition of both nanoparticles. Given these findings, although both MWCNTs and GO nanoparticles are seen to notably improve the membrane performance, PES membranes with 1 wt.% GO loading provided the highest removal of natural organic matter, such as HA, under the same experimental conditions.

Carbide-derived carbon as an extraordinary material for the removal of chromium from an aqueous solution.

In the present work, the adsorptive removal of chromium (Cr) from water by carbide-derived carbon (CDC) was investigated. The morphology and structure of the CDC were characterized by using FTIR, SEM, TEM, XRD, and N2 adsorption-desorption measurements. The effect of adsorption parameters including contact time, initial Cr concentration, temperature, initial solution pH, and CDC dosage was examined on the removal of Cr ions. The kinetic analysis revealed that the experimental data on the removal of Cr ions on CDC is well correlated with the pseudo-second order kinetic model (with R2 > 0.999), while the equilibrium data were fitted by the Redlich-Peterson isotherm model (with R2 > 0.992). The Langmuir and Sips models were also in good compliance with the equilibrium data, indicating a monolayer coverage of Cr ions onto the CDC surface with some heterogeneous active adsorption sites. The CDC revealed a notable Langmuir adsorption capacity of 159.1 mg/g for Cr ions at pH 6 and room temperature. The thermodynamic analysis illustrated that the Cr ions elimination by CDC is a feasible adsorption process and endothermic in nature. After five adsorption/desorption cycles, less than 18% reduction in the adsorption capacity was obtained indicating the stability and reusability of the CDC. Moreover, the CDC demonstrated an excellent potential in removing the Cr ions from real brackish water. According to the adsorption data, both physical and chemical adsorption processes occurred, and the adsorption was mainly controlled by electrostatic interactions with a possible reduction of hexavalent Cr to trivalent Cr at acidic conditions.

Kinetic and thermodynamic investigations of surfactants adsorption from water by carbide-derived carbon.

The objective of the study is to investigate the potential of carbide-derived carbon (CDC) for the adsorptive removal of nonionic t-octylphenoxy poly ethoxy ethanol (TX-100), anionic sodium dodecylbenzene sulfonate (SDBS) and cationic 1-hexadecylpyridinium bromide (HDPB) surfactants from water. The CDC was characterized using TEM, SEM, FTIR, BET, EDS, XPS methods and zeta potential measurements. The effects of adsorption parameters included initial surfactant concentration, contact time, temperature, and pH of the feed solution were evaluated. The adsorption capacity and mechanism were determined by modeling the isotherm, kinetic and thermodynamic data. The kinetics results demonstrated that the adsorption of the surfactant by CDC obeys the pseudo 2nd order model. The thermodynamic results have shown that surfactants adsorption by CDC is an endothermic and spontaneous process. The Sips model agreed with the adsorption isotherm data of SDBS with R2 of 0.987, while both Freundlich and Redlich-Peterson models comply well with adsorption data for TX-100 and HDPB. The hydrophobic and electrostatic interactions were found the dominant mechanisms of the adsorption of the surfactant by CDC. The adsorption capacities of CDC were found to be 442.4, 462.0 and 578.4 mg/g for SDBS, HDPB and TX-100, respectively.

Review of phosphate removal from water by carbonaceous sorbents.

In the last decades, phosphate is considered the main cause of eutrophication and has received substantial attention from the scientific community. Phosphate is a major pollutant that deteriorates water quality, which has been increasing in water resources, primarily due to the increasing global population and corresponding activities. Adsorption technology is amongst the different technologies used to decrease the phosphate levels in water, and has been found to be highly effective even at low phosphate concentrations. Carbonaceous materials and their composites have been widely used for phosphate removal due to their exceptional surface properties and high phosphate sorption capacity. Considering the importance of the topic, this study reviews the reported literature in the field of adsorptive removal of phosphate over various carbon-based adsorbents such as activated carbon, charcoal, graphene, graphene oxide, graphite and carbon nanotubes. Moreover, insights into the adsorption behaviour, experimental parameters, mechanisms, thermodynamics, effect of coexisting ions and the possible desorption processes of phosphate onto modified and unmodified carbonaceous adsorbents are also considered. Finally, research challenges and gaps have been highlighted.

Carbide Derived Carbon (CDC) as novel adsorbent for ibuprofen removal from synthetic water and treated sewage effluent.

PURPOSE: Pharmaceuticals are becoming one of the largest environmental concerns when it comes to the water treatment industry. Increased usage of these chemicals poses a serious risk to ecology and human health due to their leakage into surface waters. In the present study, carbide derived carbon (CDC) was used for the first time as a new adsorbent to remove ibuprofen from synthetic water and wastewater effluent. METHODS: The morphology, chemical composition, surface area and surface charge of the CDC particles were investigated using the transmission electron microscopy, scanning electron microscopy, energy dispersive spectroscopy, Fourier transform infrared spectroscopy, BET analysis and zeta potential measurements. The effects of CDC dosage, temperature, initial pH and agitation speed on the adsorption process were examined by using batch adsorption experiments. Moreover, the adsorption kinetics, thermodynamics, and isotherms were investigated. RESULTS: Adsorption and kinetic equilibrium data demonstrate that the adsorption of ibuprofen onto the CDC obeys the Langmuir isotherm model and the kinetics follow the pseudo-2nd order mechanism. The thermodynamic results reveal that ibuprofen adsorption is endothermic and spontaneous. The ibuprofen removal by CDC was mainly controlled by the electrostatic forces at high pH of the feed solution and by the dispersive interactions in acidic media. The ibuprofen removal is promoted at high temperature, high agitation speed and low pH. The highest adsorption capacity of ibuprofen onto the CDC was 367 mg/g at pH 3. Furthermore, the CDC efficiently removed ibuprofen from spiked treated sewage effluent. CONCLUSIONS: The obtained data indicate that the CDC provides a fast and efficient adsorptive removal of ibuprofen both from a model aqueous solution and treated sewage effluent.

Surface modification of carbon nanotubes with copper oxide nanoparticles for heat transfer enhancement of nanofluids.

Over the last few years, nanoparticles have been used as thermal enhancement agents in many heat transfer based fluids to improve the thermal conductivity of the fluids. Recently, many experiments have been carried out to prepare different types of nanofluids (NFs) showing a tremendous increase in thermal conductivity of the base fluids with the addition of a small amount of nanoparticles. However, little experimental work has been proposed to calculate the flow behaviour and heat transfer of nanofluids and the exact mechanism for the increase in effective thermal conductivity in heat exchangers. This study mainly focuses on the development of nanomaterial composites by incorporating copper oxide nanoparticles (CuO) onto the surfaces of carbon nanotubes (CNTs). The CNT-CuO nanocomposite was used to prepare water-based heat transfer NFs. The morphological surfaces and loading contents of the CNT-CuO nanocomposite were characterized using field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and thermogravimetric analysis (TGA) while the physical and thermal properties of the water-based nanofluids were characterized using differential scanning calorimetry (DSC), the Mathis TCi system and a viscosity meter for measuring the heat capacity, thermal conductivity and viscosity of the synthesized NFs, respectively. The heat transfer and the pressure drop studies of the NFs were conducted by a horizontal steel tube counter-flow heat exchanger under turbulent flow conditions. The experimental results showed that the developed NFs with different concentrations of modified CNTs (0.01, 0.05 and 0.1 wt%) have yielded a significant increase in specific heat capacity (102% higher than pure water) and thermal conductivity (26% higher than pure water) even at low concentration. The results also revealed that the heat rate of the NF was higher than that of the base liquid (water) and increased with increasing the concentration of nanoparticles. Furthermore, no significant effect of the nanoparticles on the pressure drop of the system was observed.