Speciation analysis of inorganic As and Sb in urban dust using slurry sampling and detection by fast sequential hydride generation atomic absorption spectrometry.

In this work, a methodology for chemical speciation analysis of inorganic As and Sb in urban dust using slurry sampling and detection by fast sequential hydride generation atomic absorption spectrometry is proposed. Doehlert design and desirability function were used to find the optimum conditions for hydride generation (1.0 mol L-1 HCl and 0.9% m v-1 NaBH4). The accuracy of the analytical method was evaluated by analysis of reference material fly ash (BCR 176R), addition and recovery tests for inorganic As species, and comparison of independent methods for Sb determination in urban dust samples. The determination of the total concentrations of As and Sb and their inorganic species presented good accuracy, between 80 ± 1 and 101 ± 6%. Precision was expressed as the relative standard deviation and was better than 4.7% (n = 3). The limit-of-quantification values were 0.23 and 1.03 mg kg-1 for As and Sb, respectively. The methodology was applied to eight samples of dust collected in an urban area of Salvador and Jaguaquara cities, Bahia, Northeast, Brazil, with an aerodynamic size lower than 38 µm. Concentrations of pentavalent inorganic species (iAs5+ and iSb5+) in relation to trivalent species (iAs3+ and iSb3+) were found in urban dust collected in the city of Salvador, which are regarded as more toxic for both elements. The enrichment factor and geoaccumulation index (Igeo) values showed that for some samples, the concentrations of iAs and iSb presented strong enrichment and, and regarding environment, strong to moderately polluted by iAs and iSb, with an indication of anthropogenic contributions. The occurrence of these inorganic constituents in the urban area of Salvador can be related with intense industrial activities and vehicular traffic.

Characterisation and source identification of the total airborne particulate matter collected in an urban area of Aracaju, Northeast, Brazil.

In this work, studies using samples collected in an urban area of Aracaju city, Sergipe State, Northeast, Brazil revealed that soil dust in suspension was the main source of total airborne particulate matter (TAPM), followed by vehicular pollution. The concentration profiles for Cu, Fe, Mn, Ni, V and Ti were established for the collected TAPM samples. The concentrations of SO2 and smoke were also measured all along the 42 sampling days. Through multivariate data analysis of the results a correlation between Fe, Mn, Ni and Ti in the mineral composition of the particles was established, indicating soil dust in suspension as the main source of TAPM. The concentrations of Cu and smoke were found to be related to vehicular traffic, and the second largest source of TAPM. Enrichment factors (EF) were calculated for the studied elements, and only Cu was found to be enriched. The concentrations of the elements in TAPM were evaluated using the geoaccumulation index (Igeo), and Fe, Mn, Ni, V and Ti were found to derive from natural sources, in TAPM. However, approximately 55% of the samples did not presented Cu contamination (Igeo≤0), and the remaining 45% presented Cu concentrations levels that indicated between low to moderate (0

Investigation of chemical modifiers for the direct determination of arsenic in fish oil using high-resolution continuum source graphite furnace atomic absorption spectrometry.

High-resolution continuum source graphite furnace atomic absorption spectrometry (HR-CS GF AAS) has been applied for the development of a method for the determination of total As in fish oil samples using direct analysis. The method does not use any sample pretreatment, besides dilution with 1-propanole, in order to decrease the oil viscosity. The stability and sensitivity of As were evaluated using ruthenium and iridium as permanent chemical modifiers and palladium added in solution over the sample. The best results were obtained with ruthenium as the permanent modifier and palladium in solution added to samples and standard solutions. Under these conditions, aqueous standard solutions could be used for calibration for the fish oil samples diluted with 1-propanole. The pyrolysis and atomization temperatures were 1400 °C and 2300 °C, respectively, and the limit of detection and characteristic mass were 30 pg and 43 pg, respectively. Accuracy and precision of the method have been evaluated using microwave-assisted acid digestion of the samples with subsequent determination by HR-CS GF AAS and ICP-MS; the results were in agreement (95% confidence level) with those of the proposed method.

Assessment of the Halogen Content of Brazilian Inhalable Particulate Matter (PM10) Using High Resolution Molecular Absorption Spectrometry and Electrothermal Vaporization Inductively Coupled Plasma Mass Spectrometry, with Direct Solid Sample Analysis.

Halogens in the atmosphere play an important role in climate change and also represent a potential health hazard. However, quantification of halogens is not a trivial task, and methods that require minimum sample preparation are interesting alternatives. Hence, the aim of this work was to evaluate the feasibility of direct solid sample analysis using high-resolution continuum source molecular absorption spectrometry (HR-CS MAS) for F determination and electrothermal vaporization-inductively coupled plasma mass spectrometry (ETV-ICP-MS) for simultaneous Cl, Br, and I determination in airborne inhalable particulate matter (PM10) collected in the metropolitan area of Aracaju, Sergipe, Brazil. Analysis using HR-CS MAS was accomplished by monitoring the CaF molecule, which was generated at high temperatures in the graphite furnace after the addition of Ca. Analysis using ETV-ICP-MS was carried out using Ca as chemical modifier/aerosol carrier in order to avoid losses of Cl, Br, and I during the pyrolysis step, with concomitant use of Pd as a permanent modifier. The direct analysis approach resulted in LODs that were proven adequate for halogen determination in PM10, using either standard addition calibration or calibration against a certified reference material. The method allowed the quantification of the halogens in 14 PM10 samples collected in a northeastern coastal city in Brazil. The results demonstrated variations of halogen content according to meteorological conditions, particularly related to rainfall, humidity, and sunlight irradiation.