Effect of Different Adhesive Systems Used for Immediate Dentin Sealing on Bond Strength of a Self-Adhesive Resin Cement to Dentin.

OBJECTIVE: The purpose of this study was to investigate the immediate and three-month water storage behavior of adhesives when used for immediate dentin sealing (IDS). METHODS AND MATERIALS: Four adhesive systems were used to perform IDS: a one-step self-etch (Xeno V), a two-step self-etch (Clearfil SE Bond), a two-step etch-and-rinse (XP Bond), and a three-step etch-and-rinse (Optibond FL). For the control group, IDS was not performed. The self-adhesive resin cement RelyX Unicem was used for the luting procedures. After seven days of water storage, specimens (n=6) were sectioned into beams (n=5) with an approximately 1-mm2 cross-sectional area. Half of the specimens were tested in tension after seven days of water storage at 37°C, while the other half was stored for three months prior to testing in tension using a universal testing machine (1 mm/min). The failure pattern was determined using a stereomicroscope and scanning electron microscopy. Microtensile bond strength (µTBS) data were statistically analyzed by two-way analysis of variance and Tukey post hoc test (α=0.05). RESULTS: After seven days, the control group presented the lowest µTBS but did not differ from XP Bond and Clearfil SE Bond. After three months, there was no µTBS difference between the IDS groups and the control. CONCLUSIONS: After seven days of water storage, the groups with IDS presented higher µTBS values than the control group, although XP Bond and Clearfil SE Bond did not present significant differences. However, after three months of storage in water, IDS groups did not differ significantly from control group, which did not receive IDS.

Clinical performance of one-step self-etch adhesives applied actively in cervical lesions: 24-month clinical trial.

OBJECTIVES: To evaluate the clinical performance of two one-step self-etch adhesives in noncarious cervical lesions (NCCL) under active or passive application mode. METHODS: Thirty-one patients with four NCCL were enrolled in this study. One hundred and twenty-four restorations were placed according to one of the following conditions: 1) Adper Prompt L-Pop (AP), active application (APA); 2) AP, passive application (APP); 3) Xeno III (XE), active application (XEA), or 4) XE, passive application (XEP). The restorations were evaluated by the FDI World Dental Federation criteria at baseline and after six, 12, and 24 months of clinical service. The effects of adhesive, mode of application, and recall period were assessed via mixed generalized linear model (α=0.05). RESULTS: The adhesive AP and the passive application mode showed significantly higher marginal staining than did XE and active application, respectively (p<0.05). With regard to the retention rates, the active application mode yielded higher retention rates at the 24-month recall compared to the passive application, regardless of the material. The individual retention rates (95% confidence interval) of both adhesives in the active application mode were the same, 96.8% (83.8-99.4%), while in the passive application rates were 87.1% (71.2-94.9%) and 80.7% (63.7-90.8%) for XE and AP, respectively. CONCLUSIONS: The active application improved the retention rates of both adhesives after 24 months and minimized the marginal staining at enamel margins.

Short-term effects of silage volatile compounds on feed intake and digestion in beef cattle.

Two experiments were conducted to evaluate whether fermentation end products in silage affect intake and digestion in beef cattle. Six rumen-cannulated Nellore steers were randomly assigned to a replicated 3 × 3 Latin square design with 14-d periods. Each period consisted of 9 d for adaptation and 5 d for sample collection. Steers were housed in a tie-stall barn and individually fed once daily at 0800 h. The dietary treatments in Exp. 1 were as follows: 60% corn silage plus 40% concentrate (CON), 60% corn silage with added ethanol (2.8% on a DM basis) and 40% concentrate (ET), and 60% corn silage with added lactic acid (5.4% on a DM basis) and 40% concentrate (LA). The DMI was similar (P = 0.41) across treatments (average 11.7 kg/d); however, the LA treatment increased the ruminal pH (P = 0.01) and decreased the acetate:propionate ratio (P < 0.01). Diet digestibility decreased by 2.2 to 2.5 percentage units when the DM content was determined by oven drying (at 105°C) rather than by toluene distillation. The treatments in Exp. 2 were as follows: 75% sugarcane silage with no volatile fraction (oven dried at 60°C and rehydrated) and 25% concentrate (75D), 75% sugarcane silage (original moisture content) and 25% concentrate (75W), and 40% sugarcane silage and 60% concentrate (40W). Approximately 21% of the DM content of sugarcane silage consisted of volatile compounds. The presence of these compounds did not alter the DMI (P = 0.36) but did increase both the acetate:propionate ratio (P < 0.01) and the fractional absorption rates of valerate (P < 0.01) and ethanol (P = 0.02) in the empty reticulorumen. The 40W diet led to a greater DMI (40W = 9.79 vs. 75W = 6.19 kg/d; P < 0.01), which altered most of the measured variables traditionally associated with high-concentrate diets. As in Exp. 1, diet digestibility decreased by 1.5 to 5.4 units when the DM content was determined by oven drying at 105°C rather than by toluene distillation. In this short-term study, volatile compounds did not inhibit the DMI or the digestion process of the animals. On the contrary, volatile compounds contributed to the energy content of the silage, composing up to 10% of the energy value as determined by digestibility. Due to the short experimental periods, the results from this study should be interpreted with caution.

Performance of dairy cows fed high levels of acetic acid or ethanol.

Ethanol and acetic acid are common end products from silages. The main objective of this study was to determine whether high concentrations of ethanol or acetic acid in total mixed ration would affect performance in dairy cows. Thirty mid-lactation Holstein cows were grouped in 10 blocks and fed one of the following diets for 7 wk: (1) control (33% Bermuda hay + 67% concentrates), (2) ethanol [control diet + 5% ethanol, dry matter (DM) basis], or (3) acetic acid (control diet + 5% acetic acid, DM basis). Ethanol and acetic acid were diluted in water (1:2) and sprayed onto total mixed rations twice daily before feeding. An equal amount of water was mixed with the control ration. To adapt animals to these treatments, cows were fed only half of the treatment dose during the first week of study. Cows fed ethanol yielded more milk (37.9 kg/d) than those fed the control (35.8 kg/d) or acetic acid (35.3 kg/d) diets, mainly due to the higher DM intake (DMI; 23.7, 22.2, and 21.6 kg/d, respectively). The significant diet × week interaction for DMI, mainly during wk 2 and 3 (when acetic acid reached the full dose), was related to the decrease in DMI observed for the acetic acid treatment. There was a diet × week interaction in excretion of milk energy per DMI during wk 2 and 3, due to cows fed acetic acid sustained milk yield despite lower DMI. Energy efficiency was similar across diets. Blood metabolites (glucose, insulin, nonesterified fatty acids, ethanol, and γ-glutamyl transferase activity) and sensory characteristics of milk were not affected by these treatments. Animal performance suggested similar energy value for the diet containing ethanol compared with other diets. Rumen conversion of ethanol to acetate and a concomitant increase in methane production might be a plausible explanation for the deviation of the predicted energy value based on the heat of combustion. Therefore, the loss of volatile compounds during the drying process in the laboratory should be considered when calculating energy content of fermented feedstuffs.

Prevalence of Plasmodium falciparum and P. vivax in an area of transmission located in Pará State, Brazil, determined by amplification of mtDNA using a real-time PCR assay.

The need for a more sensitive and time-efficient assay for malaria has led to the development of molecular assays involving real-time PCR (qPCR), a procedure that has the potential to detect low levels of parasitemia, identify mixed infections, and allow for precise differentiation of species via melting curve analysis or TaqMan fluorescence-labeled probes. Since the first study published in 2001 at least 17 assays have been developed, most of them using SSUrRNA as the target gene. We used qPCR to detect Plasmodium falciparum and P. vivax by amplification of mtDNA; this technique was evaluated on whole-blood samples from people living in areas of malaria transmission in the Brazilian Amazon region located in the area of inclusion of highway BR-163 (Cuiabá-Santarém) in Pará State: São Luiz do Tapajós, a municipal district of Itaituba (N = 74); Três Boeiras, a municipal district of Trairão (N = 134), and São Raimundo, a municipal district of Aveiro (N = 62). The results from the real-time PCR-based method were compared to conventional microscopy and to an established mtDNA-PCR assay. The qPCR (mtDNA) method was 16-19 times more efficient than the conventional PCR (mtDNA) and microscopy for detecting plasmodial infections.

Growth, feed intake, carcass characteristics, and eating behavior of feedlot lambs fed high-concentrate diets containing soybean hulls.

The objectives of this experiment were to determine the effects of replacing ground corn with soybean hulls (SH) in high-concentrate diets on the growth (56-d period), carcass characteristics, and eating behavior of feedlot lambs. Sixty-four Santa Inês ram lambs (18.3 ± 2.8 kg of BW and 69 ± 5 d of age) were assigned to a randomized complete block design experiment with 8 blocks and 4 diets. The control diet contained 10% coastcross (Cynodon sp.) hay, 70% corn, and no SH (SH0) in the dietary DM. In the remaining diets, SH replaced corn at the rate of 15 (SH15), 30 (SH30), or 45% (SH45) of the original corn concentration, resulting in 0, 10.5, 21.0, or 31.4% SH in the dietary DM. Dry matter intake increased linearly (P < 0.01) when SH replaced ground corn (1.0, 1.0, 1.1, and 1.1 kg/d for SH0, SH15, SH30, and SH45, respectively). There was no effect on ADG of lambs, with values of 276, 278, 282, and 287 g for SH0, SH15, SH30, and SH45, respectively. Feed efficiency decreased linearly (P < 0.01) with SH inclusion. Carcass measures were not affected by SH as a replacement for ground corn. Eating time, expressed as minutes per day and minutes per gram of NDF, showed a quadratic effect (P < 0.05), whereas no effect was observed when expressed as minutes per gram of DM. Rumination, in minutes per day, was not influenced by dietary SH inclusion, but a linear decrease (P < 0.01) was observed when this variable was expressed as minutes per gram of NDF. Soybean hulls can replace up to 45% of the ground corn (31.4% of SH in the dietary DM) in high-concentrate diets fed to feedlot lambs without negative effects on ADG and carcass measures. The linear decrease in feed efficiency (11.6% reduction from SH0 to SH45) suggests that optimal dietary SH inclusion rates should be dictated by the relative costs of SH and corn.

Chlorhexidine-containing acid conditioner preserves the longevity of resin-dentin bonds.

The current study evaluated the effect of 2% chlorhexidine digluconate (CHX) on the immediate and six-month resin-dentin bond strength (BS) and nanoleakage pattern (NL) of etch-and-rinse adhesives when applied in aqueous or associated to the phosphoric acid conditioner. The occlusal enamel of 42 caries-free extracted molars was removed in order to expose a flat dentin surface. In groups 1 and 2 (control-C), the surfaces were acid etched with conventional phosphoric acid, and the adhesives Prime&Bond NT (PB) and Adper Single Bond 2 (SB) were applied after rinsing, drying and rewetting with water. In groups 3 and 4 (Ac/CHX), the adhesives were applied in a similar manner, however, a 2% CHX-containing acid was previously applied. In groups 5 and 6 (CHX), the adhesives were applied according to the control group; however, the rewetting procedure was performed with an aqueous solution of 2% CHX for 60 seconds. Composite buildups (Opallis, FGM) were constructed incrementally, and the specimens were longitudinally sectioned in the "x" and "y" directions to obtain bonded sticks (0.8 mm2) to be tested in tension at 0.5 mm/minute immediately or after six months of water storage. For NL, two bonded sticks from each tooth were coated with nail varnish, placed in silver nitrate and polished down with SiC paper. Resin-dentin interfaces were analyzed by EDX-SEM. The BS and NL data from each adhesive was submitted to two-way repeated measures ANOVA and Tukey's test (alpha=0.05). After six months of water storage, significant reductions in BS were observed for both adhesives in the control group (p<0.05). When Ac/CHX or CHX was used, no significant reductions in BS were observed for both systems. Nanoleakage was more evident in the control group than in the experimental groups (p<0.05), even after six months. The use of CHX in an aqueous solution or associated with the acid conditioner was effective for reducing degradation of resin-dentin bonds after six months of water storage.

Pontes de miocárdio em cäes: I. Frequência e largura / Myocardic bridges in dogs: I. Frequency and width

Estudaram-se em 134 coraçöes de cäes de diferentes raças, 80 machos e 54 fêmeas sem aparente patologia cardíaca, a frequência e largura das pontes de miocárdio, mediante injeçäo das artérias coronárias com soluçäo de gelatina ou Neoprene látex. Verificou-se que as pontes de miocárdio ocorrem em 45,52 por cento dos cäes examinados, sendo mais frequentemente observadas em machos (27,91 por cento) do que em fêmeas (17,91 por cento), com largura variando de 0,1 cm a 2,3 cm, com média de 0,89 cm, em ventrículos com altura média de 6,38 cm, e a frequência, largura e o número de pontes de miocárdio num mesmo coraçäo näo dependem da altura do ventrículo

Pontes de miocárdio em cäes. II. Topologia / Myocardial bridges in dogs. II. Topology

Estudou-se em 134 coraçöes de cäes de diferentes raças a localizaçäo das pontes de miocárdio, mediante dissecaçäo das artérias coronárias injetadas com soluçäo de gelatina ou Neoprene Látex. Verificou-se que as pontes de miocárdio ocorrem em 90,43 por cento nos ramos da a. coronária esquerda e em 9,57 por cento nos ramos da a. coronária direita. Sua posiçäo foi assinalada em 37,23 por cento na porçäo dorsal do ventrículo, em 28,72 por cento na média, em 21,28 por cento na ventral, em 7,45 por cento no ápice e simultaneamente nas porçöes dorsal e média em 3,19 por cento e nas porçöes média e ventral em 2,13 por cento. Näo foram notadas diferenças estatisticamente significativas em relaçäo ao sexo