Innovative strategy for the effective utilization of coal waste slag in the Fenton-like process for the degradation of trichloroethylene.

In response to environmental concerns at the global level, there is considerable momentum in the exploration of materials derived from waste that are both sustainable and eco-friendly. In this study, CS-Fe (carbon, silica, and iron) composite was synthesized from coal gasification slag (CGS) and innovatively applied as a catalyst to activate PS (persulfate) for the degradation of trichloroethylene (TCE) in water. Scanning electron microscope (SEM), fourier transmission infrared spectroscopy (FTIR), energy dispersive x-ray spectroscopy (EDS), brunauer, emmet, and teller (BET) technique, and x-ray diffractometer (XRD) spectra were employed to investigate the surface morphology and physicochemical composition of the CS-Fe composite. CS-Fe catalyst showed a dual nature by adsorption and degradation of TCE simultaneously, displaying 86.1% TCE removal in 3 h. The synthesized CS-Fe had better adsorption (62.1%) than base material CGS (36.4%) due to a larger BET surface area (770.8 m2 g-1), while 24.0% TCE degradation was recorded upon the activation of PS by CS-Fe. FTIR spectra confirmed the adsorption and degradation of TCE by investigating the used and fresh samples of CS-Fe catalyst. Scavengers and Electron paramagnetic resonance (EPR) analysis confirmed the availability of surface radicals and free radicals facilitated the degradation process. The acidic nature of the solution favored the degradation while the presence of bicarbonate ion (HCO3-) hindered this process. In conclusion, these results for real groundwater, surfactant-added solution, and degradation of other TCE-like pollutants propose that the CS-Fe composite offers an economically viable and favorable catalyst in the remediation of organic contaminants within aqueous solutions. Further investigation into the catalytic potential of coal gasification slag-based carbon materials and their application in Fenton reactions is warranted to effectively address a range of environmental challenges.

Degradation of trichloroethylene in aqueous solution by FeS2 catalyst under innovative oxic environments.

Rapid growth and industrialization have become a major threat to water contamination with carcinogenic chlorinated hydrocarbons such as trichloroethylene (TCE). Therefore, this study aims to assess the TCE degradation performance through advanced oxidation process (AOP) using catalyst FeS2 in combination with oxidants persulfate (PS), peroxymonosulfate (PMS), and hydrogen peroxide (H2O2) in PS/FeS2, PMS/FeS2, and H2O2/FeS2 systems, respectively. TCE concentration was analyzed using gas chromatography (GC). The results found the trend for TCE degradation by the systems was PMS/FeS2>PS/FeS2>H2O2/FeS2 (99.84, 99.63, and 98.47%, respectively). Degradation of TCE was analyzed at different pH ranges (3-11) and maximum degradation at a wide pH range was observed for PMS/FeS2. The analysis using electron paramagnetic resonance (EPR) and scavenging tests explored responsible reactive oxygen species (ROS) for TCE degradation and found that HO• and SO4-• played the most effective role. The results of catalyst stability showed PMS/FeS2 system the most promising with the stability of 99, 96 and 50% for the first, second and third runs, respectively. The system was also found efficient in the presence of surfactants (TW-80, TX-100, and Brij-35) in ultra-pure water (89.41, 34.11, 96.61%, respectively), and actual groundwater (94.37, 33.72, and 73.48%, respectively), but at higher reagents dosages (5X for ultra-pure water and 10X actual ground water). Furthermore, it is demonstrated that the oxic systems have degradation capability for other TCE-like pollutants. In conclusion, due to its high stability, reactivity, and cost-effectiveness, PMS/FeS2 system could be a better choice for the treatment of TCE contaminated water and can be beneficial for field application.

Phycoremediation of industrial wastewater using Vaucheria debaryana and Cladophora glomerata.

Rapid urbanization and industrialization are regarded as the leading causes of environmental pollution, mainly aquatic pollution. This study was carried out to investigate the use of algal species Cladophora glomerata (CG) and Vaucheria debaryana (VD) as a cost-effective and environmentally friendly phycoremediators for composite industrial effluent. After the pot experimentation using algal species, a considerable decrease in electrical conductivity (EC: 49.10-81.46%), dissolved oxygen (DO: 3.76-8.60%), biological oxygen demand (BOD: 7.81-39.28%), chemical oxygen demand (COD: 7.81-39.28%), total suspended solids (TSS: 38.09-62.21%), and total dissolved solids (TDS: 38.09-62.21%) was observed. Before and after experimentation, the heavy metals were also quantified using atomic absorption spectrophotometry (AAS), and considerable reduction was observed in Cd (41.02-48.75%) and Pb (48.72-57.03%) concentrations. The Cd concentration determined in CTCG (control treatment for Cladophora glomerata containing tap water), CG (treatment pot for Cladophora glomerata containing industrial effluents), CTVD (control pot for Vaucheria debaryana containing tap water), and VD (treatment pot for Vaucheria debaryana containing industrial effluents) biomass was 0.06, 0.499, 0.035, and 0.476 mg/kg, respectively. The Pb uptake determined in CTCG, CG, CTVD, and VD was 0.32, 1.12, 0.31, and 0.49 mg/kg, respectively, using wet digestion method and ASS. The data revealed that C. glomerata has the highest bioconcentration factor for Cd (98.42%), followed by Pb (92.57%) in treatment pots containing industrial effluents (CG and VD). Furthermore, C. glomerata showed the highest bioconcentration factor for Pb (86.49%) as compared to Cd (75%) in tap water (CTCG and CTVD). The t test analysis revealed that heavy metal concentrations significantly (p ≤ 0.05) reduced through the phycoremediation process. The analysis found that C. glomerata removed 48.75% of Cd and 57.027% of Pb from industrial effluents. Phytotoxicity assay was also performed by cultivating Triticum sp. in order to analyze the toxicity of the untreated (control) and treated water samples. Phytotoxicity result shows that the effluent treated with both Cladophora glomerata and Vaucheria debaryana gives better wheat (Triticum sp.) plant % germination, plant height (cm), and root height (cm). The highest plant % germination was showed by treated CTCG (90%), followed by CTVD (80%) and CG (70%) and VD (70%). The study concluded that phycoremediation using C. glomerata and V. debaryana is one of the environment-friendly approaches. The proposed algal-based strategy is economically viable and environmentally sustainable that can be utilized for the remediation of industrial effluents.

Groundwater quality assessment and its vulnerability to pollution: a study of district Nowshera, Khyber Pakhtunkhwa, Pakistan.

Groundwater is the drinking water source for the majority of rural settlements of district Nowshera, Khyber Pakhtunkhwa, Pakistan. The study aimed to analyze the groundwater quality and its vulnerability to pollution and to develop its spatial distribution mapping. For this purpose, forty-eight groundwater samples were collected from dug wells, tube wells, and hand pumps of sixteen villages and analyzed for physicochemical parameters. The XY coordinates of the sample's sources were marked by Magellan Triton 1500 handheld global positioning system (GPS). The results were compared with WHO and Pak-EPA guidelines. The results of the majority of selected parameters were found within the WHO and Pak-EPA guidelines; however, in certain areas the concentration of total dissolved solids (TDS), chlorides (Cl-), and alkalinity were higher than the guideline limits. Based on cumulative water quality the excellent water quality prevails over an area of 376 km2 (21% of district area), good water quality 726 km2 (42%), poor 424 km2 (24%), very poor 116 km2 (6%), and unfit for drinking 84 km2 (4%). The water of the Nizampur and Rashaki areas were categorized unfit for drinking. The groundwater quality of nearly one-half of the district varies from poor to very poor, and the soil type and vadose zone sediment/material was found the key reason for groundwater contamination. Based on the infiltration capacity of vadose zone material, the study area was divided into four water pollution vulnerable zones. The low vulnerable zone covers an area of 104 km2, moderate 862 km2, high 667 km2, and very high 93 km2. The most important factor which determines the vulnerability of the groundwater to contamination is the vadose zone material/sediment which in turn determines the soil infiltration capacity. The generated groundwater susceptibility and water quality maps provide critical information for identifying optimal locations for supply wells.

Modification of coal fly ash and its use as low-cost adsorbent for the removal of directive, acid and reactive dyes.

Directive, acid and reactive dyes are the carcinogenic dyes which have complex structures and difficult to remove from the industrial wastewater. In this study, coal fly ash (CFA) was modified with HCl and NaOH solution and used for the removal of direct fast scarlet 4BS, direct sky blue 5B, acid navy blue R, and reactive turquoise blue KN-G dyes. Laboratory experiments were carried out to analyze the performance of modified coal fly ash (MCFA) to check the removal efficiency and adsorption capacity of dyes. The maximum removal efficiency of direct fast scarlet 4BS and direct sky blue 5B were recorded 96.03% and 93.820%, respectively using 0.05 g adsorbent dosage at 100 mg/L initial concentration. The results of MCFA were compared with carbon black, chitosan, starch, zeolite and unmodified coal fly ash (UMCFA) at lower dosage 0.05 g and higher dosage 0.4 g. Adsorption isotherm were analyzed by Langmuir and Freundlich model by different dyes concentrations, the result stated that Freundlich and Langmuir model (±0.9918, ±0.9974) was fitted by chemisorption and physisorption methods for all four dyes. Adsorption kinetic were also determined by Pseudo-first-order and Pseudo-second-order at different contact times with dye molecules and adsorbent active sites, and the results showed that the adsorption behaviors of all four dyes were described better by pseudo-second-order kinetics than pseudo-first-order kinetics. Recommended dosage of modified fly ash is between 10 ‱ to 20 ‱ for simulated textile industrial waste water and regeneration temperature is 300 â„ƒ.

Popular wood and sugarcane bagasse biochars reduced uptake of chromium and lead by lettuce from mine-contaminated soil.

As a result of metal mining activities in Pakistan, toxic heavy metals (HMs) such as chromium (Cr) and lead (Pb) often enter the soil ecosystem, accumulate in food crops and cause serious human health and environmental issues. Therefore, this study examined the efficacy of biochar for contaminated soil remediation. Poplar wood biochar (PWB) and sugarcane bagasse biochar (SCBB) were amended to mine-contaminated agricultural soil at 3% and 7% (wt/wt) application rates. Lactuca sativa (Lettuce) was cultivated in these soils in a greenhouse, and uptake of HMs (Cr and Pb) as well as biomass produced were measured. Subsequently, health risks were estimated from uptake data. When amended at 7%, both biochars significantly (P<0.01) reduced plant uptake of Cr and Pb in amended soil with significant (P<0.01) increase in biomass of lettuce as compared to the control. Risk assessment results showed that both biochars decreased the daily intake of metals (DIM) and associated health risk due to consumption of lettuce as compared to the control. The Pb human health risk index (HRI) for adults and children significantly (P<0.01) decreased with sugarcane bagasse biochar applied at 7% rate relative to other treatments (including the control). Relative to controls, the SCBB and PWB reduced Cr and Pb uptake in lettuce by 69%, 73.7%, respectively, and Pb by 57% and 47.4%, respectively. For both amendments, HRI values for Cr were within safe limits for adults and children. HRI values for Pb were not within safe limits except for the sugarcane bagasse biochar applied at 7%. Results of the study indicated that application of SCBB at 7% rate to mine impacted agricultural soil effectively increased plant biomass and reduced bioaccumulation, DIM and associated HRI of Cr and Pb as compared to other treatments and the control.

Biochar efficacy for reducing heavy metals uptake by Cilantro (Coriandrum sativum) and spinach (Spinaccia oleracea) to minimize human health risk.

Environmentally friendly and cost-effective techniques are required to reclaim land degraded during mining activities. Bioaccumulation of heavy metals (HMs) in vegetables grown on contaminated soils can increase human health risks. The potential effects of hardwood biochar (HWB) was assessed for chromium (Cr), zinc (Zn), copper (Cu), manganese (Mn) and lead (Pb) bioavailability in mine-contaminated soils and their subsequently bioaccumulation in crops and associated health risk. HWB was applied to chromium-manganese mine contaminated soils at the rate of 3% to investigate the efficiency of HWB for the second crop in crop rotation technique. Cilantro (Coriandrum sativum) and spinach (Spinaccia oleracea) were grown as second crop in the same pots which were already used for rice cultivation as first crop (without adding further amendments). Application of HWB decreased the concentrations of Cr, Zn, Cu, Mn, and Pb in cilantro by 25.5%, 37.1%, 42.5%, 34.3%, and 36.2%, respectively as compared to control. In spinach, the reduction in concentrations of Cr was 75.0%, Zn 24.1%, Cu 70.1%, Mn 78.0%, and Pb 50.5% as compared to control. HWB significantly (P < 0.01) reduced the HMs uptake in spinach cultivated in the amended soils as compared to the spinach in control. Bioaccumulation factor results also indicate that HWB decreased the bioaccumulation of selected HMs in cilantro and spinach, thus reducing health risks. Results of the study clearly demonstrate that the use of HWB can significantly reduce HMs in vegetables, associated health risk and improve food quality, therefore can be used as soil amendment for reclamation of mine-degraded soils.

Remediation of industrial wastewater using four hydrophyte species: A comparison of individual (pot experiments) and mix plants (constructed wetland).

Remediation and management of industrial wastewater (IWW) using hydrophytes act as one of the cost effective and environmentally friendly technologies. The present study was conducted to assess the role and efficiency of selected four hydrophyte species through constructed wetland (CW) for the removal of heavy metals (HMs) from IWW. Samples of wastewater (WW) were collected from the main drain of Hayatabad Industrial Estate (Peshawar, Pakistan) and analysed for HMs like cadmium (Cd), copper (Cu) and lead (Pb) along with basic physicochemical parameters like pH, electric conductivity (EC), total suspended solids (TSS), total dissolved solids (TDS), dissolved oxygen (DO), biological oxygen demand (BOD), chemical oxygen demand (COD), dissolved organic carbon (DOC) through standard analytical methods. Four hydrophytes species such as Typha latifolia (cattail), Eichhornia crassipes (water hyacinth), Lemna gibba (duck weed) and Pistia stratiotes (water cabbage) were transplanted into CW (mix cultivation). Each selected species was also cultivated in individual pots for investigating their efficiency to remove HMs. The Cd, Cu and Pb removal efficiency of CW was recorded as 39.5%, 80.3% and 85.5%, respectively. The removal efficacy of hydrophyte species including cattail, water hyacinth, duck weed and water cabbage was 96.2%, 72.2%, 60.4% and 93.3%, respectively for Cd, while 83.6%, 82.3%, 90.0% and 81.7% for Cu and 95.9%, 78.0%, 91.3% and 97.1% for Pb, respectively. Findings of T-Test and One-Way ANOVA showed that the concentrations of Cd, Cu and Pb in IWW were significantly (P ≤ 0.01) reduced by the treatment of hydrophytes revealing the higher efficiency of CW and selected species used in this study. The HMs were removed in order of Pb > Cu > Cd. Most efficient removal for Cd was found by water cabbage, Cu by duck weed and Pb by water hyacinth. It was concluded that CW is one of the environmentally friendly and cost-effective technologies that can be used for the treatment of IWW due to the efficiency of hydrophytes species in terms of HMs removal.