Disclosing Topographical and Chemical Patterns in Confined Films of High-Molecular-Weight Block Copolymers under Controlled Solvothermal Annealing.

The microphase separation of high-molecular-weight block copolymers into nanostructured films is strongly dependent on the surface fields. Both, the chain mobility and the effective interaction parameters can lead to deviations from the bulk morphologies in the structures adjacent to the substrate. Resolving frustrated morphologies with domain period L0 above 100 nm is an experimental challenge. Here, solvothermal annealing was used to assess the contribution of elevated temperatures of the vapor Tv and of the substrate Ts on the evolution of the microphase-separated structures in thin films symmetric of polystyrene-b-poly(2vinylpyridine) block copolymer (PS-PVP) with L0 about 120 nm. Pronounced topographic mesh-like and stripe patterns develop on a time scale of min and are attributed to the perforated lamella (PL) and up-standing lamella phases. By setting Tv/Ts combinations it is possible to tune the sizes of the resulting PL patterns by almost 10%. Resolving chemical periodicity using selective metallization of the structures revealed multiplication of the topographic stripes, i.e., complex segregation of the component within the topographic pattern, presumably as a result of morphological phase transition from initial non-equilibrium spherical morphology. Reported results reveal approaches to tune the topographical and chemical periodicity of microphase separation of high-molecular-weight block copolymers under strong confinement, which is essential for exploiting these structures as functional templates.

Real-World Experience with Brolucizumab Compared to Aflibercept in Treatment-Naïve and Therapy-Refractory Patients with Diabetic Macular Edema.

Background: To report on the outcome of intravitreal brolucizumab compared to aflibercept in patients with diabetic macular edema (DME). Methods: Prospective, observational, study in 35 eyes of 24 patients with a loading dose of five injections of 6 mg brolucizumab every 6 weeks (q6w, treatment-naïve eyes) or a minimum of two injections of brolucizumab q6w after the switch (recalcitrant DME eyes), followed by a treat and extend (T&E) regimen. The results were compared with 40 eyes of 31 DME patients who were treated with aflibercept. The data were obtained from the Berlin Macula Registry. The primary outcome measure was the change in best-corrected visual acuity (BCVA) at week 36. Secondary outcome measures were the change in central retinal thickness (CRT) and the treatment intervals until week 36. Results: BCVA increased significantly in treatment-naïve DME eyes treated with either brolucizumab (+0.12 logMAR, +6.4 letters, p = 0.03) or aflibercept (+0.19 logMAR, +9.5 letters, p = 0.001). In recalcitrant DME eyes, BCVA also increased significantly after switching to brolucizumab (+0.1 logMAR, +5 letters, p = 0.006) or aflibercept (+0.11 logMAR, +5.5 letters, p = 0.02). All treatment-naïve and recalcitrant DME eyes had a significant decrease in CRT after treatment with brolucizumab (p = 0.001 and p < 0.001) or aflibercept (p = 0.0002 and p = 0.03). At week 36, the mean treatment interval for brolucizumab was 11.3 weeks, while for aflibercept, it was 6.5 weeks for treatment-naïve eyes and 9.3 weeks vs. 5.3 weeks for pretreated eyes. Conclusions: In routine clinical practice, patients with treatment-naïve and recalcitrant DME showed a favorable response to brolucizumab and aflibercept therapy, with a reduced injection frequency after brolucizumab treatment.

Lignin Upconversion by Functionalization and Network Formation.

Lignin, a complex and abundant biopolymer derived from plant cell walls, has emerged as a promising feedstock for sustainable material development. Due to the high abundance of phenylpropanoid units, aromatic rings, and hydroxyl groups, lignin is an ideal candidate for being explored in various material applications. Therefore, the demand on lignin valorization for development of value-added products is significantly increasing. This mini-review provides an overview of lignin upconversion, focusing on its functionalization through chemical and enzymatic routes, and its application in lignin-based polymer resins, hydrogels, and nanomaterials. The functionalization of lignin molecules with various chemical groups offers tailored properties and increased compatibility with other materials, expanding its potential applications. Additionally, the formation of lignin-based networks, either through cross-linking or blending with polymers, generates novel materials with improved mechanical, thermal, and barrier properties. However, challenges remain in optimizing functionalization techniques, preserving the innate complexity of lignin, and achieving scalability for industrial implementation. As lignin's potential continues to be unlocked, it is poised to contribute significantly to the shift towards more eco-friendly and resource-efficient industries.

Fabrication of Patchy Silica Microspheres with Tailor-Made Patch Functionality using Photo-Iniferter Reversible-Addition-Fragmentation Chain-Transfer (PI-RAFT) Polymerization.

Their inherent directional information renders patchy particles interesting building blocks for advanced applications in materials science. In this study, a feasible method to fabricate patchy silicon dioxide microspheres is demonstrated, which they are able to equip with tailor-made polymeric materials as patches. Their fabrication method relies on a solid-state supported microcontact printing (µCP) routine optimized for the transfer of functional groups to capillary-active substrates, which is used to introduce amino functionalities as patches to a monolayer of particles. Acting as anchor groups for polymerization, photo-iniferter reversible addition-fragmentation chain-transfer (RAFT) is used to graft polymer from the patch areas. Accordingly, particles with poly(N-acryloyl morpholine), poly(N-isopropyl acrylamide), and poly(n-butyl acrylate) are prepared as representative acrylic acid-derived functional patch materials. To facilitate their handling in water, a passivation strategy of the particles for aqueous systems is introduced. The protocol introduced here, therefore, promises a vast degree of freedom in engineering the surface properties of highly functional patchy particles. This feature is unmatched by other techniques to fabricate anisotropic colloids. The method, thus, can be considered a platform technology, culminating in the fabrication of particles that possess locally precisely formed patches on particles at a low µm scale with a high material functionality.

Versatile Microfluidics Separation of Colloids by Combining External Flow with Light-Induced Chemical Activity.

Separation of particles by size, morphology, or material identity is of paramount importance in fields such as filtration or bioanalytics. Up to now separation of particles distinguished solely by surface properties or bulk/surface morphology remains a very challenging process. Here a combination of pressure-driven microfluidic flow and local self-phoresis/osmosis are proposed via the light-induced chemical activity of a photoactive azobenzene-surfactant solution. This process induces a vertical displacement of the sedimented particles, which depends on their size and surface properties . Consequently, different colloidal components experience different regions of the ambient microfluidic shear flow. Accordingly, a simple, versatile method for the separation of such can be achieved by elution times in a sense of particle chromatography. The concepts are illustrated via experimental studies, complemented by theoretical analysis, which include the separation of bulk-porous from bulk-compact colloidal particles and the separation of particles distinguished solely by slight differences in their surface physico-chemical properties.

15 Years of Success and Still Improving: Polymers.

In 2009, the inaugural issue of Polymers was released [...].

Treatment of neovascular age-related macular degeneration: insights into drug-switch real-world from the Berlin Macular Registry.

PURPOSE: Bevacizumab, ranibizumab, and aflibercept are commonly used to treat neovascular age-related macular degeneration (nAMD). The results of various interventional, mostly randomized head-to-head studies, indicate statistical non-inferiority of these three drugs. The results of these studies are often interpreted as the three drugs being freely interchangeable, resulting in some health systems to pressure ophthalmologists to preferentially use the less expensive bevacizumab. This study analyzes switching from aflibercept or ranibizumab to bevacizumab and back under real-world conditions in order to investigate the assumption of interchangeability of the drugs. METHODS: Treatment data of IVT patients with diagnosed nAMD were extracted from the clinical Berlin Macular Registry database. Patients who underwent a drug switch from aflibercept or ranibizumab to bevacizumab were subject of this study. Statistical comparisons were pre-planned for best corrected visual acuity, central retinal thickness, macular volume, and length of injection interval. Additional endpoints were analyzed descriptively. RESULTS: Mean visual acuity decreased from 0.57 ± 0.05 under aflibercept/ranibizumab to 0.68 ± 0.06 logMAR after the switch (P = 0.001; N = 63). CRT increased from 308 ± 11 µm to 336 ± 16 µm (P = 0.011; N = 63). About half of the subjects were switched back: visual acuity increased from 0.69 ± 0.08 logMAR to 0.58 ± 0.09 logMAR (N = 26). CRT decreased from 396 ± 28 to 337 ± 20 µm (N = 28). CONCLUSION: The data provides real-world evidence that there is loss of visual acuity and an increase in retinal edema after switching to bevacizumab. Thus, the assumption of free interchangeability cannot be confirmed in this cohort.

Proton Therapy for 166 Patients with Iris Melanoma: Side Effects and Oncologic Outcomes.

OBJECTIVE: To investigate the oncologic and functional outcomes of a large cohort of patients with a favorable stage of circumscribed and diffuse iris melanoma who underwent primary proton treatment and the risk factors related to initial tumor characteristics and the treatment field architecture. DESIGN: Retrospective, single-center, case study. PARTICIPANTS: We reviewed 225 patients with iris melanoma who were consecutively treated with proton beam therapy at our institution between 1998 and 2020. METHODS: We performed Kaplan-Meier time-to-event analyses and multivariate Cox proportional hazard analyses to identify the impacts of tumor characteristics and target volumes on oncologic and functional outcomes. MAIN OUTCOME MEASURES: We measured local tumor control, eye preservation rates, metastasis-free survival, cataract and glaucoma-directed surgery, intraocular pressure, and changes in visual acuity. RESULTS: Of the 192 patients with tumors confined to the iris (T1a-c) who underwent proton therapy as primary treatment, a total of 166 patients (mean age, 58.4 years; 88 women) with a minimum follow-up of 6 months were included. Multifocal or diffuse tumor spread was present in 77 (46.4%) patients. The median follow-up time was 54.0 (interquartile range, 27.4-91.8 months) months. Local recurrence occurred in 2 patients (1.2%) with circumscribed iris melanoma. Enucleation was a rare event (n = 5, 3%) and no patient developed metastatic disease. A large-treatment field (full aperture, involving > 10 clock hours) was identified as a risk factor for the development of secondary glaucoma (hazard ratio [HR], 6.3; P < 0.001) and subsequent surgical interventions (HR, 10.85; P < 0.001). The large-treatment field group showed a significant decline in visual acuity (logarithm of the minimum angle of resolution > 0.3; log-rank P < 0.0001), which was associated with secondary glaucoma (HR, 3.40; P = 0.002). CONCLUSIONS: Proton therapy provides an effective, noninvasive treatment option for patients with a favorable stage of iris melanoma. Irradiation of the anterior segment for up to 10 clock hours is associated with a low risk of the development of secondary glaucoma and vision loss. FINANCIAL DISCLOSURE(S): Proprietary or commercial disclosure may be found after the references.

Nanodeformations of microcapsules: comparing the effects of cross-linking and nanoparticles.

The mechanical properties of proteinaceous and composite microcapsules loaded with oil were measured by SFM and evaluated using the Reissner model. Comparison of the obtained results reveals significantly higher Young's moduli of protein capsules due to intermolecular crosslinking. In contrast, conformational restrictions in composite microcapsules inhibit protein crosslinking leading to the reduction of their elasticity.

Impact of Adjuvant Ocular Interventions on the Quality of Life of Patients with Uveal Melanoma after Proton Beam Therapy.

Introduction: Proton beam therapy is an established primary treatment for patients with nonmetastasized uveal melanoma. Adjuvant local interventions, like intravitreal injections or surgery, were shown to improve long-term eye preservation; however, their impact on the patient's quality of life (QOL) remains unknown. Methods: In a post-radiotherapeutic follow-up, we prospectively collected data on QOL, visual acuity, and interventional adjuvant procedures. QOL was measured with QOL-C30 questionnaire and quality of life questionnaire OPT30 at baseline, and at 3 and 12 months after proton therapy. Patients were grouped by the type of adjuvant treatment. The impact on QOL was analyzed by comparing changes in the mean score values and visual acuity for different interventional subgroups, with generalized linear mixed models and Wilcoxon signed-rank tests. Results: We received 108 (100%) and 95 (88.0%) questionnaires at 3 and 12 months post-therapy, respectively. Adjuvant interventions included observation (n = 61, 56.5%), intravitreal injections (n = 17, 15.7%), and an intraocular surgical procedure (n = 30, 27.8%). In the latter group, several QOL items significantly declined after the 3-month adjuvant interval, but they partially recovered at the 12-month follow-up. In all adjuvant-intervention groups, global QOL scores returned to baseline levels at 12 months. Conclusion: Posttreatment adjuvant interventions had no long-lasting effects on QOL in patients with uveal melanoma.

Synthesis of nanostructured protein-mineral-microcapsules by sonication.

We propose a simple and eco-friendly method for the formation of composite protein-mineral-microcapsules induced by ultrasound treatment. Protein- and nanoparticle-stabilized oil-in-water (O/W) emulsions loaded with different oils are prepared using high-intensity ultrasound. The formation of thin composite mineral proteinaceous shells is realized with various types of nanoparticles, which are pre-modified with Bovine Serum Albumin (BSA) and subsequently characterized by EDX, TGA, zeta potential measurements and Raman spectroscopy. Cryo-SEM and EDX mapping visualizations show the homogeneous distribution of the densely packed nanoparticles in the capsule shell. In contrast to the results reported in our previous paper,1 the shell of those nanostructured composite microcapsules is not cross-linked by the intermolecular disulfide bonds between BSA molecules. Instead, a Pickering-Emulsion formation takes place because of the amphiphilicity-driven spontaneous attachment of the BSA-modified nanoparticles at the oil/water interface. Using colloidal particles for the formation of the shell of the microcapsules, in our case silica, hydroxyapatite and calcium carbonate nanoparticles, is promising for the creation of new functional materials. The nanoparticulate building blocks of the composite shell with different chemical, physical or morphological properties can contribute to additional, sometimes even multiple, features of the resulting capsules. Microcapsules with shells of densely packed nanoparticles could find interesting applications in pharmaceutical science, cosmetics or in food technology.

A Dual pH- and Light-Responsive Spiropyran-Based Surfactant: Investigations on Its Switching Behavior and Remote Control over Emulsion Stability.

A cationic surfactant containing a spiropyran unit is prepared exhibiting a dual-responsive adjustability of its surface-active characteristics. The switching mechanism of the system relies on the reversible conversion of the non-ionic spiropyran (SP) to a zwitterionic merocyanine (MC) and can be controlled by adjusting the pH value and via light, resulting in a pH-dependent photoactivity: While the compound possesses a pronounced difference in surface activity between both forms under acidic conditions, this behavior is suppressed at a neutral pH level. The underlying switching processes are investigated in detail, and a thermodynamic explanation based on a combination of theoretical and experimental results is provided. This complex stimuli-responsive behavior enables remote-control of colloidal systems. To demonstrate its applicability, the surfactant is utilized for the pH-dependent manipulation of oil-in-water emulsions.

Protein Nanopore Membranes Prepared by a Simple Langmuir-Schaefer Approach.

Filtration through membranes with nanopores is typically associated with high transmembrane pressures and high energy consumption. This problem can be addressed by reducing the respective membrane thickness. Here, a simple procedure is described to prepare ultrathin membranes based on protein nanopores, which exhibit excellent water permeance, two orders of magnitude superior to comparable, industrially applied membranes. Furthermore, incorporation of either closed or open protein nanopores allows tailoring the membrane's ion permeability. To form such membranes, the transmembrane protein ferric hydroxamate uptake protein component A (FhuA) or its open-pore variant are assembled at the air-water interface of a Langmuir trough, compressed to a dense film, crosslinked by glutaraldehyde, and transferred to various support materials. This approach allows to prepare monolayer or multilayer membranes with a very high density of protein nanopores. Freestanding membranes covering holes up to 5 µm in diameter are visualized by atomic force microscopy (AFM), helium ion microscopy, and transmission electron microscopy. AFM PeakForce quantitative nanomechanical property mapping (PeakForce QNM)  demonstrates remarkable mechanical stability and elastic properties of freestanding monolayer membranes with a thickness of only 5 nm. The new protein membrane can pave the way to energy-efficient nanofiltration.

Solid-Phase Microcontact Printing for Precise Patterning of Rough Surfaces: Using Polymer-Tethered Elastomeric Stamps for the Transfer of Reactive Silanes.

We present a microcontact printing (µCP) routine suitable to introduce defined (sub-) microscale patterns on surface substrates exhibiting a high capillary activity and receptive to a silane-based chemistry. This is achieved by transferring functional trivalent alkoxysilanes, such as (3-aminopropyl)-triethoxysilane (APTES) as a low-molecular weight ink via reversible covalent attachment to polymer brushes grafted from elastomeric polydimethylsiloxane (PDMS) stamps. The brushes consist of poly{N-[tris(hydroxymethyl)-methyl]acrylamide} (PTrisAAm) synthesized by reversible addition-fragmentation chain-transfer (RAFT)-polymerization and used for immobilization of the alkoxysilane-based ink by substituting the alkoxy moieties with polymer-bound hydroxyl groups. Upon physical contact of the silane-carrying polymers with surfaces, the conjugated silane transfers to the substrate, thus completely suppressing ink-flow and, in turn, maximizing printing accuracy even for otherwise not addressable substrate topographies. We provide a concisely conducted investigation on polymer brush formation using atomic force microscopy (AFM) and ellipsometry as well as ink immobilization utilizing two-dimensional proton nuclear Overhauser enhancement spectroscopy (1H-1H-NOESY-NMR). We analyze the µCP process by printing onto Si-wafers and show how even distinctively rough surfaces can be addressed, which otherwise represent particularly challenging substrates.

Primary Vitreoretinal Lymphoma Therapy Monitoring: Significant Vitreous Haze Reduction After Intravitreal Rituximab.

BACKGROUND/AIMS: Intravitreal rituximab is an off-label treatment option for primary vitreoretinal lymphoma (PVRL). The objective of this study was to monitor the therapeutic response and safety profile of intravitreal rituximab in a cohort of PVRL patients. METHODS: In this retrospective, uncontrolled, open label, multicentre study, 20 eyes from 15 consecutive patients diagnosed with PRVL received at least one intravitreal injection of 1mg in 0.1ml rituximab. Biodata of the PVRL patients was recorded as well as visual acuity and vitreous haze score immediately before rituximab intravitreal injection and at follow-up examinations. Intravitreal rituximab safety data was also recorded. Additional rituximab injections were made during control visits on a pro re nata (PRN) regime using increased vitreous haze to indicate recurrence. RESULTS: There was significant vitreous haze reduction (p=0.0002) followed by significant improvement of visual acuity (mean best visual acuity before therapy 0.57 logMAR, after therapy 0.20 logMAR (p=0.0228) during the follow-up time up to 4 years. Only mild ocular side effects were reported. Median follow-up time was 565 days (range, 7-1253 days). CONCLUSION: Intravitreal rituximab therapy shows promising PVRL regression without any severe side effects. Although our clinical data support rituximab as intravitreal therapy in PVRL disease, further study is warranted.

Construction of Highly Ordered Glyco-Inside Nano-Assemblies through RAFT Dispersion Polymerization of Galactose-Decorated Monomer.

Glyco-assemblies derived from amphiphilic sugar-decorated block copolymers (ASBCs) have emerged prominently due to their wide application, for example, in biomedicine and as drug carriers. However, to efficiently construct these glyco-assemblies is still a challenge. Herein, we report an efficient technology for the synthesis of glyco-inside nano-assemblies by utilizing RAFT polymerization of a galactose-decorated methacrylate for polymerization-induced self-assembly (PISA). Using this approach, a series of highly ordered glyco-inside nano-assemblies containing intermediate morphologies were fabricated by adjusting the length of the hydrophobic glycoblock and the polymerization solids content. A specific morphology of complex vesicles was captured during the PISA process and the formation mechanism is explained by the morphology of its precursor and intermediate. Thus, this method establishes a powerful route to fabricate glyco-assemblies with tunable morphologies and variable sizes, which is significant to enable the large-scale fabrication and wide application of glyco-assemblies.

About the mechanism of ultrasonically induced protein capsule formation.

In this paper, we propose a consistent mechanism of protein microcapsule formation upon ultrasound treatment. Aqueous suspensions of bovine serum albumin (BSA) microcapsules filled with toluene are prepared by use of high-intensity ultrasound following a reported method. Stabilization of the oil-in-water emulsion by the adsorption of the protein molecules at the interface of the emulsion droplets is accompanied by the creation of the cross-linked capsule shell due to formation of intermolecular disulfide bonds caused by highly reactive species like superoxide radicals generated sonochemically. The evidence for this mechanism, which until now remained elusive and was not proven properly, is presented based on experimental data from SDS-PAGE, Raman spectroscopy and dynamic light scattering.

Self-Assembly Behavior of Oppositely Charged Inverse Bipatchy Microcolloids.

A directed attractive interaction between predefined "patchy" sites on the surfaces of anisotropic microcolloids can provide them with the ability to self-assemble in a controlled manner to build target structures of increased complexity. An important step toward the controlled formation of a desired superstructure is to identify reversible electrostatic interactions between patches which allow them to align with one another. The formation of bipatchy particles with two oppositely charged patches fabricated using sandwich microcontact printing is reported. These particles spontaneously self-aggregate in solution, where a diversity of short and long chains of bipatchy particles with different shapes, such as branched, bent, and linear, are formed. Calculations show that chain formation is driven by a combination of attractive electrostatic interactions between oppositely charged patches and the charge-induced polarization of interacting particles.