RESUMO
To recharge lithium-ion batteries quickly and safely while avoiding capacity loss and safety risks, a novel electrode design that minimizes cell polarization at a higher current is highly desired. This work presents a dual-layer electrode (DLE) technology via sequential coating of two different anode materials to minimize the overall electrode resistance upon fast charging. Electrochemical impedance spectroscopy and distribution of relaxation times analysis revealed the dynamic evolution of electrode impedances in synthetic graphite (SG) upon a change in the state of charge (SOC), whereas the natural graphite (NG) maintains its original impedance regardless of SOC variation. This disparity dictates the sequence of the NG and SG coating layers within the DLE, considering the temporal SOC gradient developed upon fast charging. Simulation and experimental results suggest that DLE positioning NG and SG on the top (second-layer) and bottom (first-layer), respectively, can effectively reduce the overall resistance at a 4 C-rate (15-min charging), demonstrating two times higher capacity retention (61.0%) over 200 cycles than its counterpart with reversal sequential coating, and is higher than single-layer electrodes using NG or NG/SG binary mixtures. Hence, this study can guide the combinatorial sequence for multi-layer coating of various active materials for a lower-resistivity, thick-electrode design.
RESUMO
This paper proposes a 4D printed smart soft carrier with a hemispherical hollow and openable lid. The soft carrier is composed of a lid with a slot (with a shape of 4 legs), a border, and a hemisphere. The soft carrier is fabricated by 4D printing using smart hydrogels. Specifically, the lid, border, and hemisphere are fabricated using a thermo-responsive poly(N-isopropylacrylamide) (PNIPAM) hydrogel, a non-responsive polyethylene glycol (PEG) hydrogel with superparamagnetic iron oxide nanoparticles (SPIONs), and a PEG hydrogel, respectively. Since the SPIONs are included in the border, the slot in the center of the lid is opened and closed according to the temperature change caused by near-infrared (NIR) irradiation, and the proposed soft carrier is magnetically driven by an external magnetic field. The hemisphere enables the storage and transport of cargo. The proposed soft carrier can control the opening and closing of the slot and movement to a desired position in water. Several cargo delivery experiments were conducted using various shapes and numbers of cargo. In addition, the proposed soft carrier can successfully handle small living marine organisms. This soft carrier can be manufactured by 4D printing and operated by dual stimuli (NIR and magnetic field) and can safely deliver various types of cargo and delicate organisms without leakage or damage. The flexibility of 4D printing enables the size of the soft carrier to be tailored to the specific physical attributes of various objects, making it an adaptable and versatile delivery approach.
RESUMO
Thick electrodes can substantially enhance the overall energy density of batteries. However, insufficient wettability of aqueous electrolytes toward electrodes with conventional hydrophobic binders severely limits utilization of active materials with increasing the thickness of electrodes for aqueous batteries, resulting in battery performance deterioration with a reduced capacity. Here, we demonstrate that controlling the hydrophilicity of the thicker electrodes is critical to enhancing the overall energy density of batteries. Hydrophilic binders are synthesized via a simple sulfonation process of conventional polyvinylidene fluoride binders, considering physicochemical properties such as mechanical properties and adhesion. The introduction of abundant sulfonate groups of binders (i) allows fast and sufficient electrolyte wetting, and (ii) improves ionic conduction in thick electrodes, enabling a significant increase in reversible capacities under various current densities. Further, the sulfonated binder effectively inhibits the dissolution of cathode materials in reactive aqueous electrolytes. Overall, our findings significantly enhance the energy density and contribute to the development of practical zinc-ion batteries.
RESUMO
The effects of thiodiphenol based epoxy resin on the thermal property of the composites containing aluminum oxide were investigated. The thermal conductivities and thermal diffusivities of the composites were dependent on the polymer resin. At the same content of Al2O3, the thermal conductivity and thermal diffusivity of composites made by synthesized polymer resin exhibited higher than that of composite made by bisphenol-A resin. The obtained maximum thermal conductivity of the composite was 0.25 W/mK, which was 0.4 times as large as that of the conventional bisphenol-A epoxy resin which has an amorphous structure. It is supposed that the reason for the high heat conductivity obtained in thiodiphenol based epoxy resin is certain high packing structure.
Assuntos
Dissecção Aórtica , Anomalias dos Vasos Coronários , Infarto do Miocárdio , Idoso , Dissecção Aórtica/diagnóstico , Dissecção Aórtica/terapia , Angiografia Coronária , Anomalias dos Vasos Coronários/diagnóstico , Anomalias dos Vasos Coronários/terapia , Feminino , Humanos , Masculino , Infarto do Miocárdio/diagnóstico , Intervenção Coronária Percutânea , Doenças VascularesRESUMO
Amyloidosis is defined as the presence of extra-cellular deposits of an insoluble fibrillar protein, amyloid. The pulmonary involvement of amyloidosis is usually classified as tracheobronchial, parenchymal nodular, or diffuse alveolar septal. A single nodular lesion can mimic various conditions, including malignancy, pulmonary tuberculosis, and fungal infection. To date, only one case of nodular pulmonary amyloidosis has been reported in Korea, a case involving multiple nodular lesions. Here, we report and discuss the case of a patient having single nodular amyloidosis.
RESUMO
We report here on a rare case of primary AL hepatic amyloidosis associated with multiple myeloma in a 64-year-old woman. The patient was referred for evaluating her progressive jaundice and right upper quadrant pain. (18)F-fluorodeoxyglucose ((18)F-FDG) positron emission tomography (PET)/computed tomography (CT) showed diffusely and markedly increased (18)F-FDG uptake in the liver. Although there have been several case studies showing positive (18)F-FDG uptake in pulmonary amyloidosis, to the best of our knowledge, the (18)F-FDG PET/CT findings of hepatic amyloidosis or primary hepatic amyloidosis associated with multiple myeloma have not been reported previously.