Random lasing from optical fibers with phase separated glass cores.

A novel random laser, integrating a passive optical fiber with a phase separated aluminosilicate core-silica cladding as the feedback medium, is proposed and presented. The core exhibits greatly enhanced Rayleigh scattering, therefore requiring a significantly reduced length of scattering fiber (4 m) for lasing. With a Yb-doped fiber as the gain medium, the fiber laser operates at 1050 nm with low threshold power and possesses an output that can be amplified through conventional means. Furthermore, the laser was found to have a high degree of spatial coherence, spectral broadening with increasing input power, and temporal spectral variation. The facile setup and results herein pave the way for further study and applications based on low threshold random fiber lasers.

Laser restructuring and photoluminescence of glass-clad GaSb/Si-core optical fibres.

Semiconductor-core optical fibres have potential applications in photonics and optoelectronics due to large nonlinear optical coefficients and an extended transparency window. Laser processing can impose large temperature gradients, an ability that has been used to improve the uniformity of unary fibre cores, and to inscribe compositional variations in alloy systems. Interest in an integrated light-emitting element suggests a move from Group IV to III-V materials, or a core that contains both. This paper describes the fabrication of GaSb/Si core fibres, and a subsequent CO2 laser treatment that aggregates large regions of GaSb without suppressing room temperature photoluminescence. The ability to isolate a large III-V crystalline region within the Si core is an important step towards embedding semiconductor light sources within infrared light-transmitting silicon optical fibre.

Less than 1% quantum defect fiber lasers via ytterbium-doped multicomponent fluorosilicate optical fiber.

Two ytterbium-doped fiber lasers exhibiting quantum defects of less than 1% are demonstrated, in which pumping at wavelengths of 976.6 and 981.0 nm yielded lasing at wavelengths of 985.7 and 989.8 nm, respectively. The multicomponent fluorosilicate active optical fiber, fabricated using the molten core method, has spectral characteristics similar to those of fluoride glasses, namely short average emission wavelength and long upper state lifetime. A best-case slope efficiency of 62.1% was obtained, matching the theoretical model very well. With further fiber and laser optimization, slope efficiencies approaching the quantum limit should ultimately be possible. A reduction in the quantum defect may offer significant mitigation of issues associated with fiber heating. As such, this work can serve as a possible direction for future scaling of high-power fiber laser systems.

Highly nonlinear yttrium-aluminosilicate optical fiber with a high intrinsic stimulated Brillouin scattering threshold.

Highly nonlinear (high-NA small-mode-area) optical fibers also possessing an intrinsically high stimulated Brillouin scattering threshold are described. More specifically, silica clad, yttrium-aluminosilicate core fibers are shown to exhibit an intrinsically low Brillouin gain coefficient between 0.125 and 0.139×10-11 m/W and a Brillouin gain linewidth of up to 500 MHz. Losses on the order of 0.7 dB/m were measured, resulting from impurities in the precursor materials. Nonlinear refractive index values are determined to be similar to that of silica, but significant measurement uncertainty is attributed to the need to estimate dispersion curves since their direct measurement could not be made. The interest for highly nonlinear optical fibers with a low intrinsic Brillouin gain coefficient is expected to continue, especially with the growing developments of narrow-linewidth high-energy laser systems.

Additivity of the coefficient of thermal expansion in silicate optical fibers.

A model that predicts the material additivity of the thermal expansion coefficient in the binary silicate glasses most commonly used for present (GeO2-SiO2, P2O5-SiO2, B2O3-SiO2, and Al2O3-SiO2) and emerging (BaO-SiO2) optical fibers is proposed. This model is based on a derivation of the expression for the coefficient of thermal expansion in isotropic solids, and gives direct insight on the parameters that govern its additivity in silicate glasses. Furthermore, a consideration of the local structural environment of the glass system is necessary to fully describe its additivity behavior in the investigated systems. This Letter is important for better characterizing and understanding of the impact of temperature and internal stresses on the behavior of optical fibers.

Polymer-clad silica fibers for tailoring modal area and dispersion.

We demonstrate higher-order-mode (Aeff up to ∼2000 µm2) propagation in a 100 µm outer diameter pure-silica fiber with a low-index polymer jacket commonly used for fiber laser pump guidance. This simple structure obviates the need for complex designs deemed necessary for realizing large-mode-area fibers. Modes ranging from HE1,12 to HE1,22 were found to propagate stably over 15 m in this fiber. The index step is approximately 4 times larger than that obtained with fluorine down doping; thus the fiber supports even higher-order modes, which may have implications for building rare-earth-doped fiber lasers or achieving enhanced dispersion tunability for high-energy fiber nonlinear phenomena.

Single- and few-moded lithium aluminosilicate optical fiber for athermal Brillouin strain sensing.

Results are presented toward realizing a true single-mode fiber whose Brillouin frequency shift is independent of temperature, while its dependence on strain is comparable to conventional high-silica-content single-mode fibers. Demonstrated here is a fiber with a negative thermal sensitivity dν/dT of -0.26 MHz/K and a strain sensitivity of +406 MHz/%. The suppression of the Brillouin thermal response is enabled by the large thermal expansion coefficient of the group I oxide-containing silica glass network.

Kerr nonlinear switching in a hybrid silica-silicon microspherical resonator.

A hybrid silicon-core, silica-clad microspherical resonator has been fabricated from the semiconductor core fiber platform. Linear and nonlinear characterization of the resonator properties have shown it to exhibit advantageous properties associated with both materials, with the low loss cladding supporting high quality (Q) factor whispering gallery modes which can be tuned through the nonlinear response of the crystalline core. By exploiting the large wavelength shift associated with the Kerr nonlinearity, we have demonstrated all-optical modulation of a weak probe on the timescale of the femtosecond pump pulse. This novel geometry offers a route to ultra-low loss, high-Q silica-based resonators with enhanced functionality.

Brillouin scattering properties of lanthano-aluminosilicate optical fiber.

Utilizing measurements on a lanthano-aluminosilicate core optical fiber, the specific effects of lanthana (La2O3) on the Brillouin characteristics of silica-based oxide glass optical fibers are described. Lanthana is an interesting species to investigate since it possesses a wide transparency window covering the common fiber laser and telecom system wavelengths. As might be expected, it is found that the properties of lanthana are very similar to those of ytterbia (Yb2O3), namely, low acoustic velocity, wide Brillouin spectral width, and a negative photoelastic constant, with the latter two properties affording significant reductions to the Brillouin gain coefficient. However, lanthana possesses thermo-acoustic and strain-acoustic coefficients (acoustic velocity versus temperature or strain, TAC and SAC, respectively) with signs that are opposed to those of ytterbia. The lanthano-aluminosilicate (SAL) fiber utilized in this study is Brillouin-athermal (no dependence of the Brillouin frequency on temperature), but not atensic (is dependent upon the strain), which is believed to be, to the best of our knowledge, the first demonstration of such a glass fiber utilizing a compositional engineering approach.

Silicon-core glass fibres as microwire radial-junction solar cells.

Vertically aligned radial-junction solar cell designs offer potential improvements over planar geometries, as carrier generation occurs close to the junction for all absorption depths, but most production methods still require a single crystal substrate. Here, we report on the fabrication of such solar cells from polycrystalline, low purity (99.98%) p-type silicon starting material, formed into silicon core, silica sheath fibres using bulk glass draw techniques. Short segments were cut from the fibres, and the silica was etched from one side, which exposed the core and formed a conical cavity around it. We then used vapour deposition techniques to create p-i-n junction solar cells. Prototype cells formed from single fibres have shown conversion efficiencies up to 3.6%, despite the low purity of the starting material. This fabrication method has the potential to reduce the energy cost and the silicon volume required for solar cell production. Simulations were performed to investigate the potential of the conical cavity around the silicon core for light collection. Absorption of over 90% of the incident light was predicted, over a wide range of wavelengths, using these structures in combination with a 10% volume fraction of silicon.

Brillouin spectroscopy of a novel baria-doped silica glass optical fiber.

Presented here for the first time to the best of our knowledge is a detailed Brillouin spectroscopic study of novel, highly-BaO-doped silica glass optical fibers. The fibers were fabricated utilizing a molten-core method and exhibited baria (BaO) concentrations up to 18.4 mole %. Physical characteristics such as mass density, acoustic velocity, visco-elastic damping, and refractive index are determined for the baria component of the bariosilicate system. It is found that, of each of these parameters, only the acoustic velocity is less than that of pure silica. The effect of temperature and strain on the acoustic velocity also is determined by utilizing estimates of the strain- and thermo-optic coefficients. The dependencies are found to have signs opposite to those of silica, thus suggesting both Brillouin-frequency a-thermal and a-tensic binary compositions. Via the estimate of the strain-optic coefficient and data found in the literature, the Pockels' photoelastic constant p(12) is estimated, and both a calculation and measured estimate of the Brillouin gain versus baria content are presented. Such novel fibers incorporating the unique properties of baria could be of great utility for narrow linewidth fiber lasers, high power passive components (such as couplers and combiners), and Brillouin-based sensor systems.

Longitudinally-graded optical fibers.

Optical fibers have become ubiquitous tools for the creation, propagation, manipulation, and detection of light. However, while the intensity of light propagating through the fiber can increase or decrease along the length through amplification or attenuation, respectively, the properties of the fiber itself generally do not, thus removing an opportunity to further control the behavior of light and performance of fiber-based devices. Shown here are optical fibers that exhibit significant changes in their longitudinal optical properties, specifically a tailored longitudinal numerical aperture change of about 12% over less than 20 meters of length. This is about 1900 times greater than previously reported. The Brillouin gain coefficient was found to decrease by over 6 dB relative to a standard commercial single mode fiber. Next generation analogs are expected to exhibit more than a 10 dB reduction in SBS gain using larger, yet still reasonably manufacturable gradients over practical lengths.

Linkage of oxygen deficiency defects and rare earth concentrations in silica glass optical fiber probed by ultraviolet absorption and laser excitation spectroscopy.

Ultraviolet absorption measurements and laser excitation spectroscopy in the vicinity of 248 nm provide compelling evidence for linkages between the oxygen deficiency center (ODC) and rare earth concentrations in Yb and Er-doped glass optical fibers. Investigations of YAG-derived and solution-doped glass fibers are described. For both Yb and Er-doped fibers, the dependence of Type II ODC absorption on the rare earth number density is approximately linear, but the magnitude of the effect is greater for Yb-doped fibers. Furthermore, laser excitation spectra demonstrate unambiguously the existence of an energy transfer mechanism coupling an ODC with Yb(3+). Photopumping glass fibers with a Ti:sapphire laser/optical parametric amplifier system, tunable over the 225-265 nm region, or with a KrF laser at 248.4 nm show: 1) emission features in the 200-1100 nm interval attributable only to the ODC (Type II) defect or Yb(3+), and 2) the excitation spectra for ODC (II) emission at ~280 nm and Yb(3+) fluorescence (λ ~1.03 µm) to be, within experimental uncertainty, identical. The latter demonstrates that, when irradiating Yb-doped silica fibers between ~240 and 255 nm, the ODC (II) defect is at least the primary precursor to Yb(3+) emission. Consistent with previous reports in the literature, the data show the ODC (II) absorption spectrum to have a peak wavelength and breadth of ~246 nm and ~19 nm (FWHM). Experiments also reveal that, in the absence of Yb, incorporating either Al(2)O(3) or Y(2)O(3) into glass fibers has a negligible impact on the ODC concentration. Not only do the data reported here demonstrate the relationship between the ODC (II) number density and the Yb doping concentration, but they also suggest that the appearance of ODC defects in the fiber is associated with the introduction of Yb and the process by which the fiber is formed.

Silica-clad crystalline germanium core optical fibers.

Silica-clad optical fibers comprising a core of crystalline germanium were drawn using a molten core technique. With respect to previous fibers drawn using a borosilicate cladding, the present fibers exhibit negligible oxygen despite being fabricated at more than twice the melting point of the germanium. The counterintuitive result of less oxygen when the fiber is drawn at a higher temperatures is discussed. The measured propagation loss for the fiber was 0.7 dB/cm at 3.39 µm, which is the lowest loss reported to date.

Toward a photoconducting semiconductor RF optical fiber antenna array.

Recently, optical fibers comprising a crystalline semiconductor core in a silica cladding have been successfully drawn by a conventional drawing process. These fibers are expected to exhibit a photoconductive response when illuminated by photons more energetic than the band gap of the core. In the photoconducting state, such a fiber can be expected to support driven RF currents so as to function as an antenna element, much as a plasma antenna. In this paper, we report the first device-related results on a crystalline semiconductor core optical fiber potentially useful in a photoconducting optical fiber antenna array; namely, optically induced changes to the electrical conductivity of a glass-clad germanium-core optical fiber. Since DC photoconduction measurements were masked by a photovoltaic effect, RF measurements at 5 MHz were used to determine the magnitude of the induced photoconductive effect. The observed photoconductivity, though not large in the present experiment, was comparable to that measured for the bulk crystals from which the fibers were drawn. The absorbed pumping light generated photo-carriers, thereby transforming the core from a dielectric material to a conductor. This technology could thus enable a class of transient antenna elements useful in low observable and reconfigurable antenna array applications.

Brillouin spectroscopy of YAG-derived optical fibers.

We present Brillouin spectroscopy of YAG-derived optical fibers. It is found that the addition of yttria and alumina both tend to raise the acoustic velocity when added to silica, with the change due to yttria being much weaker. The temperature-dependence of the Stokes's shift in the YAG-derived fibers is also measured, disclosing a lesser temperature dependence than conventional Ge-doped fibers. These fibers are found experimentally to have a substantially larger acoustic attenuation coefficient relative to that of bulk silica, and assuming a photoelastic constant of amorphous YAG similar to that of pure crystalline YAG, a much-reduced Brillouin gain coefficient as a result. A 40 weight percent yttria and alumina fiber has a Brillouin gain coefficient estimated to be roughly one sixth of pure silica. We also show that the addition of Er to the YAG-derived system decreases the acoustic velocity and broadens the Brillouin spectrum.

Glass-clad single-crystal germanium optical fiber.

Long lengths (250 meters) of a flexible 150 microm diameter glass-clad optical fiber containing a 15 microm diameter crystalline and phase-pure germanium core was fabricated using conventional optical fiber draw techniques. X-ray diffraction and spontaneous Raman scattering measurements showed the core to be very highly crystalline germanium with no observed secondary phases. Elemental analysis confirmed a very well-defined core-clad interface with a step-profile in composition and nominally 4 weight-percent oxygen having diffused into the germanium core from the glass cladding. For this proof-of-concept fiber, polycrystalline n-type germanium of unknown dopant concentration was used. The measured infrared transparency of the starting material was poor and, as a likely outcome, the attenuation of the resultant fiber was too high to be measured. However, the larger Raman cross-section, infrared and terahertz transparency of germanium over silicon should make these fibers of significant value for fiber-based mid- to long-wave infrared and terahertz waveguides and Raman-shifted infrared light sources once high-purity, high-resistivity germanium is employed.

Nanograined highly transparent yttria ceramics.

The field of transparent ceramics is enjoying a renaissance, as refractory oxides are being developed as alternatives to single crystals in high-performance laser systems. However, a significant challenge remains regarding the reduction of the grain size to sufficiently subwavelength dimensions in order to achieve the same degree of optical transparency as the single-crystal analog. Here we report transparent yttria (Y2O3) ceramics that were synthesized by a pressure-assisted, two-step, low-temperature sintering process with an average grain size of 300 nm. These nanograined ceramics exhibit equivalent transmission to single crystalline yttria for wavelengths greater than about 1200 nm. The single-crystal-like transmittance of the nanograined yttria ceramics in the visible and IR region is an important advancement for the use of these materials in more-extreme environments, including high-energy laser systems where reduction of scattering is paramount.

Photoluminescent characterization of atomic diffusion in core-shell nanoparticles.

Eu3+ doped LaF3 nanoparticles with core/shell morphologies were synthesized and selected spectroscopic properties were measured as a function of heat treatment times and temperatures. More specifically, the relative intensity of photoluminescence spectra, both through direct excitation of the lanthanide as well as phonon sideband spectra were evaluated with increasing amounts of time held at specific temperatures. A one dimensional approximation was used to compute an effective diffusion coefficient for the rare earth dopants in LaF3. Despite the simplicity of the model employed, the calculated diffusion coefficients based on the spectroscopic results are accurate within an order of magnitude in comparison to other fluoride crystals yielding a simplified approach to estimating kinetic and diffusion effects in optical materials.

Silicon optical fiber.

Described herein are initial experimental details and properties of a silicon core, silica glass-clad optical fiber fabricated using conventional optical fiber draw methods. Such semiconductor core fibers have potential to greatly influence the fields of nonlinear fiber optics, infrared and THz power delivery. More specifically, x-ray diffraction and Raman spectroscopy showed the core to be highly crystalline silicon. The measured propagation losses were 4.3 dB/m at 2.936 microm, which likely are caused by either microcracks in the core arising from the large thermal expansion mismatch with the cladding or to SiO(2) precipitates formed from oxygen dissolved in the silicon melt. Suggestions for enhancing the performance of these semiconductor core fibers are provided. Here we show that lengths of an optical fiber containing a highly crystalline semiconducting core can be produced using scalable fiber fabrication techniques.