Proton-beam engineered surface-point defects for highly sensitive and reliable NO2 sensing under humid environments.

Cross-interference with humidity is a major limiting factor for the accurate detection of target gases in semiconductor metal-oxide gas sensors. Under humid conditions, the surface-active sites of metal oxides for gas adsorption are easily deactivated by atmospheric water molecules. Thus, development of a new approach that can simultaneously improve the two inversely related features for realizing practical gas sensors is necessary. This paper presents a facile method to engineer surface-point defects based on proton-beam irradiation. The sensor irradiated with a proton beam shows not only an improved NO2 response but also considerable tolerance toward humidity. Based on surface analyses and DFT calculations, it is found that proton beams induce three types of point defects, which make NO2 molecules preferentially adsorb on the ZnO surfaces compared to H2O molecules, eventually enabling improved NO2 detection with less humidity interference.

Achievement of self-heated sensing of hazardous gases by WS2 (core)-SnO2 (shell) nanosheets.

With the recent rapid development of portable smart electronic devices, there is a great demand for gas sensors having high performance, high flexibility, and low energy consumption. We explored the effects of SnO2 shell thickness and operating voltage on the sensing behavior of WS2 nanosheets (NSs) deposited over a flexible substrate in self-heating mode. Commercial WS2 nanowires (NWs) were used as the core and SnO2 shells with various thicknesses were deposited on the core by an advanced physical technique, namely atomic layer deposition (ALD). With regard to CO sensing, a shell thickness of 15 nm operating at 3.4 V, was optimal. Alternatively, for NO2 sensing, the optimal shell thickness was 30 nm. Therefore, using engineering design principles to determine the shell material and shell thickness, it is possible to selectively detect reducing gases such as CO, while the response to oxidizing gases is weak. We have also discussed the details of this sensing mechanism. We believe that our results can lead to further study of C-S NSs for sensing studies from different points of views.

Interface treatment using amorphous-carbon and its applications.

Breakthrough process technologies have been introduced that can increase the chemical sensitivity of an interface at which reactions occur without significantly altering the physico-chemical properties of the material. Such an interfacial treatment method is based on amorphous-carbon as a base so that fluids can be deposited, and the desired thickness and quality of the deposition can be ensured irrespective of the interface state of the material. In addition, side effects such as diffusion and decreasing strength at the interface can be avoided. This is simpler than existing vacuum-based deposition technology and it has an unmatched industrial advantage in terms of economics, speed, accuracy, reliability, accessibility, and convenience. In particular, this amorphous-carbon interface treatment technology has been demonstrated to improve gas-sensing characteristics of NO2 at room temperature.

Room-Temperature, Highly Durable Ti3C2Tx MXene/Graphene Hybrid Fibers for NH3 Gas Sensing.

Graphene-based fibers (GFs) have aroused enormous interest in portable, wearable electronics because of their excellent mechanical flexibility, electrical conductivity, and weavability, which make them advantageous for wearable electronic devices. Herein, we report the development of metal binder-free Ti3C2Tx MXene/graphene hybrid fibers by a scalable wet-spinning process. These hybrid fibers exhibit excellent mechanical and electrical properties for applications in flexible wearable gas sensors. The synergistic effects of electronic properties and gas-adsorption capabilities of MXene/graphene allow the created fibers to show high NH3 gas sensitivity at room temperature. The hybrid fibers exhibited significantly improved NH3 sensing response (ΔR/R0 = 6.77%) compared with individual MXene and graphene. The hybrid fibers also showed excellent mechanical flexibility with a minimal fluctuation of resistance of ±0.2% and low noise resistance even after bending over 2000 cycles, enabling gas sensing during deformation. Furthermore, flexible MXene/graphene hybrid fibers were woven into a lab coat, demonstrating their high potential for wearable devices. We envisage that these exciting features of 2D hybrid materials will provide a novel pathway for designing next-generation portable wearable gas sensors.

Synthesis of Au/SnO2 nanostructures allowing process variable control.

Theoretical advances in science are inherently time-consuming to realise in engineering, since their practical application is hindered by the inability to follow the theoretical essence. Herein, we propose a new method to freely control the time, cost, and process variables in the fabrication of a hybrid featuring Au nanoparticles on a pre-formed SnO2 nanostructure. The above advantages, which were divided into six categories, are proven to be superior to those achieved elsewhere, and the obtained results are found to be applicable to the synthesis and functionalisation of other nanostructures. Furthermore, the reduction of the time-gap between science and engineering is expected to promote the practical applications of numerous scientific theories.

Fast Semiconductor-Metal Bidirectional Transition by Flame Chemical Vapor Deposition.

A simple yet powerful flame chemical vapor deposition technique is proposed that allows free control of the surface morphology, microstructure, and composition of existing materials with regard to various functionalities within a short process time (in seconds) at room temperature and atmospheric pressure as per the requirement. Since the heat energy is directly transferred to the material surface, the redox periodically converges to the energy dynamic equilibrium depending on the energy injection time; therefore, bidirectional transition between the semiconductor/metal is optionally available. To demonstrate this, a variety of Sn-based particles were created on preformed SnO2 nanowires, and this has been interpreted as a new mechanism for the response and response times of gas-sensing, which are representative indicators of the most surface-sensitive applications and show one-to-one correspondence between theoretical and experimental results. The detailed technologies derived herein are clearly influential in both research and industry.

New type of doping effect via metallization of surface reduction in SnO2.

The use of conventional doping methods requires consideration of not only the energy connection with the base material but also the limits of the type and doping range of the dopant. The scope of the physico-chemical change must be determined from the properties of the base material, and when this limit is exceeded, a large energy barrier must be formed between the base material and the dopant as in a heterojunction. Thus, starting from a different viewpoint, we introduce a so-called metallization of surface reduction method, which easily overcomes the disadvantages of existing methods while having the effect of doping the base material. Such new synthetic techniques enable sequential energy arrangements-gradients from the surface to the centre of the material-so that free energy transfer effects can be obtained as per the energies in the semiconducting band, eliminating the energy discontinuity of the heterojunction.

Incorporation of Pt Nanoparticles on the Surface of TeO2-Branched Porous Si Nanowire Structures for Enhanced Room-Temperature Gas Sensing.

A new gas sensor working in room temperature, which is compatible with silicon fabrication technology is presented. Porous silicon nanowires (NWs) were synthesized by metal-assisted chemical etching method and then TeO2 NWs branches were attached to their stem by thermal evaporation of Te powders in the presence of air. Afterwards TeO2 branched porous Si NWs were functionalized by Pt via sputtering followed by low temperature thermal annealing. Scanning electron microscopy, transmission electron microscopy and energy-dispersive X-ray spectroscopy collectively confirmed successful formation of TeO2 branched porous Si NWs functionalized by Pt nanoparticles. Their gas sensing properties in the presence of CO, C6H6 and C7H8 were tested at room temperature, for Si wafer, pristine porous Si NWs, pristine TeO2 branched porous Si NWs, and Pt functionalized TeO2 branched porous Si NWs sensors. Pt functionalized TeO2 branched porous Si NWs have higher responses to all tested gases than the other sensors. The origin of high response is discussed in detail. This new room temperature gas sensor can open a new aperture for development of gas sensors with minimum energy consumption which are compatible with silicon fabrication technology.

Porous Si nanowires for highly selective room-temperature NO2 gas sensing.

We report the room-temperature sensing characteristics of Si nanowires (NWs) fabricated from p-Si wafers by a metal-assisted chemical etching method, which is a facile and low-cost method. X-ray diffraction was used to the the study crystallinity and phase formation of Si NWs, and product morphology was examined using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). After confirmation of Si NW formation via the SEM and TEM micrographs, sensing tests were carried out at room temperature, and it was found that the Si NW sensor prepared from Si wafers with a resistivity of 0.001-0.003 Ω.cm had the highest response to NO2 gas (Rg/Ra = 1.86 for 50 ppm NO2), with a fast response (15 s) and recovery (30 s) time. Furthermore, the sensor responses to SO2, toluene, benzene, H2, and ethanol were nearly negligible, demonstrating the excellent selectivity to NO2 gas. The gas-sensing mechanism is discussed in detail. The present sensor can operate at room temperature, and is compatible with the microelectronic fabrication process, demonstrating its promise for next-generation Si-based electronics fused with functional chemical sensors.

Microwave-Assisted Synthesis of Graphene-SnO2 Nanocomposites and Their Applications in Gas Sensors.

We obtained extremely high and selective sensitivity to NO2 gas by fabricating graphene-SnO2 nanocomposites using a commercial microwave oven. Structural characterization revealed that the products corresponded to agglomerated structures of graphene and SnO2 particles, with small secondary SnOx (x ≤ 2) nanoparticles deposited on the surfaces. The overall oxygen atomic ratio was decreased with the appearance of an SnOx (x < 2) phase. By the microwave treatment of graphene-SnO2 nanocomposites, with the graphene promoting efficient transport of the microwave energy, evaporation and redeposition of SnOx nanoparticles were facilitated. The graphene-SnO2 nanocomposites exhibited a high sensor response of 24.7 for 1 ppm of NO2 gas, at an optimized temperature of 150 °C. The graphene-SnO2 nanocomposites were selectively sensitive to NO2 gas, in comparison with SO2, NH3, and ethanol gases. We suggest that the generation of SnOx nanoparticles and the SnOx phase in the matrix results in the formation of SnO2/SnO2 homojunctions, SnO2/SnOx (x < 2) heterojunctions, and SnO2/graphene heterojunctions, which are responsible for the excellent sensitivity of the graphene-SnO2 nanocomposites to NO2 gas. In addition, the generation of surface Sn interstitial defects is also partly responsible for the excellent NO2 sensing performance observed in this study.

On-chip anticancer drug test of regular tumor spheroids formed in microwells by a distributive microchannel network.

This paper proposes a new cytotoxicity assay in a microfluidic device with microwells and a distributive microfluidic channel network for the formation of cancer cell spheroids. The assay can generate rapid and uniform cell clusters in microwells and test in situ cytotoxicity of anticancer drugs including sequential drug treatments, long term culture of spheroids and cell viability assays. Inlet ports are connected to the microwells by a hydraulic resistance network. This uniform distribution of cell suspensions results in regular spheroid dimensions. Injected cancer cells were trapped in microwells, and aggregated into tumor spheroids within 3 days. A cytotoxicity test of the spheroids in microwells was subsequently processed in the same device without the extraction of cells. The in situ cytotoxicity assay of tumor spheroids in microwells was comparable with the MTT assay on hanging drop spheroids using a conventional 96-well plate. It was observed that the inhibition rate of the spheroids was less than that in the 2D culture dish and the effect on tumor spheroids was different depending on the anticancer drug. This device could provide a convenient in situ assay tool to assess the cytotoxicity of anticancer drugs on tumor spheroids, offering more information than the conventional 2D culture plate.

3-Dimensional cell culture for on-chip differentiation of stem cells in embryoid body.

This paper proposes a microfluidic device for the on-chip differentiation of an embryoid body (EB) formed in a microwell via 3-dimensional cultures of mouse embryonic carcinoma (EC) cells. The device adjusted the size of the EB by fluid volume, differentiated the EB by chemical treatment, and evaluated its effects in EC cells by on-chip immunostaining. A microfluidic resistance network was designed to control the size of the embryoid body. The duration time and flow rate into each microwell regulated the initial number of trapped cells in order to adjust the size of the EB. The docked cells were aggregated and formed a spherical EB on the non-adherent surface of the culture chip for 3 days. The EC cells in the EB were then differentiated into diverse cell lineages without attachment for an additional 4 days; meanwhile, retinoic acid (RA) was applied without serum to direct the cells into early neuronal lineage. On-chip immunostaining of the EB in the microwell with a neuronal marker was conducted to assess the differentiation-inducing ability of RA. The effect of RA on neuronal differentiation was analyzed with confocal microscopic images of the TuJ1 marker. The RA-treated cells expressed more neuronal markers and appeared as mature neuronal cells with long neurites. The fluorescence intensity of the TuJ1 in the RA-treated EB was twice that observed in the non-treated EB on day 5. It was demonstrated that the pre-screening of inducing chemicals on the early neuronal differentiation of EC cells in a single microfluidic chip was indeed feasible. This chip is expected to constitute a useful tool for assessing the early differentiation of ES cells without attachment, and is also expected to prove useful as an anti-cancer drug test platform for the cytotoxicity assay with cellular spheroids.