Short single-frequency self-pulsing Brillouin-Raman distributed feedback fiber laser.

We demonstrate that the stimulated Brillouin scattering of a 250 mm long distributed feedback Raman fiber laser can self-pulse with repetition rates up to 7 MHz, pulse widths of 25 ns, and peak powers of 1.2 W. While both CW and pulsed lasing are produced from a bespoke grating at 1119 nm this laser design could be constructed at almost any wavelength, as the Raman and Brillouin gain regions are relative to the pump wavelength. The laser has a low lasing threshold for a Raman laser of 0.55 W, a peak slope efficiency of 14 %, and a maximum average output of 0.25 W. An investigation of beating between pure Raman and Raman-pumped Brillouin lasing shows that the outputs of the two processes are highly correlated and thus the Brillouin lasing is essentially single-frequency when CW and near transform limited for pulsed operation. A phenomenological model of the Raman-Brillouin interaction shows that the pulsing behaviour of such a cavity is expected and produces very similar pulsing to that the seen in experimental results.

Manipulation of Molecular Vibrations on Condensing Er3+ State Densities for 1.5 µm Application.

Vibrational modes of chemical bonds in organic erbium (Er3+) materials play an important role in determining the efficiency of the 1.5 µm Er3+ emission. This work studies the energy coupling of the Er3+ intra-4f transitions and vibrational modes. The results demonstrate that the coupling introduces enormous nonradiative internal relaxation, which condenses the excited erbium population on to the 4I13/2 state. This suggests that vibrational modes can be advantageous for optimizing the branching ratio for the 1.5 µm transition in organic erbium materials. Through control of the quenching effect on to the 4I13/2 state and a reliable determination of intrinsic radiative rates, it is found that the pump power for population inversion can be reduced by an order of magnitude at high erbium concentrations compared to conventional inorganic erbium materials.

213 nm laser written waveguides in Ge-doped planar silica without hydrogen loading.

In this paper we present the first example of waveguides fabricated by UV writing in non-hydrogen loaded Ge-doped planar silica with 213 nm light. Single mode waveguides were fabricated and the numerical apertures and mode field diameters were measured for a range of writing fluences. A peak index change of 5.3 x 10-3 was inferred for the waveguide written with 70 kJ cm-2. The refractive index change is sufficient to match the index structure of standard optical fiber. Uniformity of the written structures was measured and a propagation loss of 0.39 ± 0.03 dB cm-1 was determined through cutback measurements.

Highly-chirped Bragg gratings for integrated silica spectrometers.

A blazed chirped Bragg grating in a planar silica waveguide device was used to create an integrated diffractive element for a spectrometer. The grating diffracts light from a waveguide and creates a wavelength dependent focus in a manner similar to a bulk diffraction grating spectrometer. An external imaging system is used to analyse the light, later device iterations plan to integrate detectors to make a fully integrated spectrometer. Devices were fabricated with grating period chirp rates in excess of 100 nm mm-1, achieving a focal length of 5.5 mm. Correction of coma aberrations resulted in a device with a footprint of 20 mm×10 mm, a peak FWHM resolution of 1.8 nm, a typical FWHM resolution of 2.6 nm and operating with a 160 nm bandwidth centered at 1550 nm.

Individual inscription of spectrally multiplexed Bragg gratings in optical multicore fibers using small spot direct UV writing.

We have demonstrated the inscription of Bragg gratings into five individual cores of a seven core fiber using small spot direct UV writing. With this technique, we defined spectrally multiplexed Bragg gratings consecutively in separate cores as well as spectrally multiplexed gratings at the same longitudinal location in different cores. The effect of bending on the optical spectrum was evaluated to allow the differentiation between cross-exposure and cross-talk, and an alignment process to reduce cross-exposure by 13 dB was found.

Direct UV written integrated planar waveguides using a 213 nm laser.

We present the first demonstration of integrated waveguides in planar silica devices fabricated using direct UV writing with 213 nm laser light. Waveguides were produced with different writing fluences and the NA and MFD of each were measured. Single mode waveguides were achieved at fluence values one-tenth that typically required when operating with a 244 nm laser, allowing for more rapid fabrication. A maximum in-plane index change of 2.4 ×10-3 for a writing fluence of 5 kJ cm-2 was estimated from NA measurements. Finally cutback measurements were performed and a propagation loss of 0.42 ± 0.07 dB cm-1 was directly measured, though losses as low as 0.2 ± 0.03 dB/cm are indicated through calculations.

ZnO indiffused MgO:PPLN ridge waveguides.

We have demonstrated the first MgO:PPLN ridge waveguides based on ZnO indiffusion and dicing. The fabrication process utilizes ductile regime dicing of a planar waveguide layer producing second harmonic generation (SHG) devices with a near-symmetric sinc2 spectral profile, indicating highly uniform 40 mm long devices. A near circular pump mode is also obtained enabling efficient coupling to single mode telecommunication fibers. A conversion efficiency of 145%/W, for 1560-780 nm SHG, has been measured.

Thermal approach to classifying sequentially written fiber Bragg gratings.

We demonstrate thermal classification of sequentially written fiber Bragg gratings. This Letter presents a process to determine the type of fiber Bragg grating written in SMF28 and GF4A by introducing the gratings to thermal treatment. This technique can be applied to several approaches based on sequential writing, including the small spot direct ultraviolet writing technique. Four different types of gratings have been identified, which are dependent on the fiber type and fluence used during the writing process.

High-birefringence direct UV-written waveguides for use as heralded single-photon sources at telecommunication wavelengths.

Direct UV-written waveguides are fabricated in silica-on-silicon with birefringence of (4.9 ± 0.2) × 10-4, much greater than previously reported in this platform. We show that these waveguides are suitable for the generation of heralded single photons at telecommunication wavelengths by spontaneous four-wave mixing. A pulsed pump field at 1060 nm generates pairs of photons in highly detuned, spectrally uncorrelated modes near 1550 nm and 800 nm. Waveguide-to-fiber coupling efficiencies of 78-91 % are achieved for all fields. Waveguide birefringence is controlled through dopant concentration of GeCl4 and BCl3 using the flame hydrolysis deposition process. The technology provides a route towards the scalability of silica-on-silicon integrated components for photonic quantum experiments.

Evanescent field refractometry in planar optical fiber.

This Letter demonstrates a refractometer in integrated optical fiber, a new optical platform that planarizes fiber using flame hydrolysis deposition (FHD). The unique advantage of the technology is survivability in harsh environments. The platform is mechanically robust, and can survive elevated temperatures approaching 1000°C and exposure to common solvents, including acetone, gasoline, and methanol. For the demonstrated refractometer, fabrication was achieved through wet etching an SMF-28 fiber to a diameter of 8 µm before FHD planarization. An external refractive index was monitored using fiber Bragg gratings (FBGs), written into the core of the planarized fiber. A direct comparison to alternative FBG refractometers is made, for which the developed platform is shown to have comparable sensitivity, with the added advantage of survivability in harsh environments.

Observations from direct UV-written, non-hydrogen-loaded, thermally regenerated Bragg gratings in double-clad photosensitive fiber.

In this Letter, experimental evidence is provided for an enhanced thermal sensitivity for a double thermal regeneration feature in fiber Bragg gratings fabricated by direct ultraviolet (UV) writing. Here 47 gratings of varying fluence and wavelength were written along a double-clad, germanium-doped core fiber. Subsequently thermal processing without hydrogen loading the fiber was performed and thermal treatment was carried out in a pure oxygen environment. Thermal sensitivity for the double regeneration increased from 13.6±0.3 pm/°C to 21.3±0.2 pm/°C. Furthermore, one of the highest nominal fluence gratings, #45, exhibited a regeneration factor of 1.73.