An H2 O-Initiated Crosslinking Strategy for Ultrafine-Nanoclusters-Reinforced High-Toughness Polymer-In-Plasticizer Solid Electrolyte.

Incorporating plasticizers is an effective way to facilitate conduction of ions in solid polymer electrolytes (SPEs). However, this conductivity enhancement often comes at the cost of reduced mechanical properties, which can make the electrolyte membrane more difficult to process and increase safety hazards. Here, a novel crosslinking strategy, wherein metal-alkoxy-terminated polymers can be crosslinked by precisely controlling the content of H2 O as an initiator, is proposed. As a proof-of-concept, trimethylaluminum (TMA)-functionalized poly(ethylene oxide) (PEO) is used to demonstrate that ultrafine Al-O nanoclusters can serve as nodes to crosslink PEO chains with a wide range of molecular weights from 10 000 to 8 000 000 g mol-1 . The crosslinked polymer network can incorporate a high concentration of plasticizers, with a total weight percentage over 75%, while still maintaining excellent stretchability (4640%) and toughness (3.87 × 104  kJ m-3 ). The resulting electrolyte demonstrates high ionic conductivity (1.41 mS cm-1 ), low interfacial resistance toward Li metal (48.1 Ω cm2 ), and a wide electrochemical window (>4.8 V vs Li+ /Li) at 30 °C. Furthermore, the LiFePO4 /Li battery shows stable cycle performance with a capacity retention of 98.6% (146.3 mAh g-1 ) over 1000 cycles at 1C (1C = 170 mAh g-1 ) at 30 °C.

Promotion of the Nucleation of Ultrafine Ni-Rich Layered Oxide Primary Particles by an Atomic Layer-Deposited Thin Film for Enhanced Mechanical Stability.

Understanding the atomistic mechanisms of non-equilibrium processes during solid-state synthesis, such as nucleation and grain structure formation of a layered oxide phase, is a critical challenge for developing promising cathode materials such as Ni-rich layered oxide for Li-ion batteries. In this study, we found that the aluminum oxide coating layer transforms into lithium aluminate as an intermediate, which has favorable low interfacial energies with the layered oxide to promote the nucleation of the latter. The fast and uniform nucleation and formation of the layered oxide phase at relatively low temperatures were evidenced using solid-state nuclear magnetic resonance and in situ synchrotron X-ray diffraction. The resulting Ni-rich layered oxide cathode has fine primary particles, as visualized by three-dimensional tomography constructed using a focused-ion beam and scanning electron microscopy. The densely packed fine primary particles enable the excellent mechanical strength of the secondary particles, as demonstrated by in situ compression tests. This strategy provides a new approach for developing next-generation, high-strength battery materials.

Temperature-Driven Anisotropic Mg2+ Doping for a Pillared LiCoO2 Interlayer Surface in High-Voltage Applications.

High-voltage lithium cobalt oxide (LiCoO2) has the highest volumetric energy density among commercial cathode materials in lithium-ion batteries due to its high working voltage and compacted density. However, under high voltage (4.6 V), the capacity of LiCoO2 fades rapidly due to parasitic reactions of high-valent cobalt with the electrolyte and the loss of lattice oxygen at the interface. In this study, we report a temperature-driven anisotropic doping phenomenon of Mg2+ that results in surface-populated Mg2+ doping to the side of the (003) plane of LiCoO2. Mg2+ dopants enter the Li+ sites, lower the valence state of Co ions with less hybridization between the O 2p and Co 3d orbitals, promote the formation of surface Li+/Co2+ anti-sites, and suppress lattice oxygen loss on the surface. As a result, the modified LiCoO2 demonstrates excellent cycling performance under 4.6 V, reaching an energy density of 911.2 Wh/kg at 0.1C and retaining 92.7% (184.3 mAh g-1) of its capacity after 100 cycles at 1C. Our results highlight a promising avenue for enhancing the electrochemical performance of LiCoO2 by anisotropic surface doping with Mg2+.

Monolithic Titanium Alkoxide Networks for Lithium-Ion Conductive All-Solid-State Electrolytes.

Reticular chemistry provides opportunities to design solid-state electrolytes (SSEs) with modular tunability. However, SSEs based on modularly designed crystalline metal-organic frameworks (MOFs) often require liquid electrolytes for interfacial contact. Monolithic glassy MOFs can have liquid processability and uniform lithium conduction, which is promising for the reticular design of SSE without liquid electrolytes. Here, we develop a generalizable strategy for the modular design of noncrystalline SSEs based on a bottom-up synthesis of glassy MOFs. We demonstrate such a strategy by linking polyethylene glycol (PEG) struts and nanosized titanium-oxo clusters into network structures termed titanium alkoxide networks (TANs). The modular design allows the incorporation of PEG linkers with different molecular weights, which give optimal chain flexibility for high ionic conductivity, and the reticular coordinative network provides a controlled degree of cross-linking that gives adequate mechanical strength. This research shows the power of reticular design in noncrystalline molecular framework materials for SSEs.

Antiexfoliating h-BN⊃In2O3 Catalyst for Oxidative Dehydrogenation of Propane in a High-Temperature and Water-Rich Environment.

Hexagonal boron nitride (h-BN) is regarded as one of the most efficient catalysts for oxidative dehydrogenation of propane (ODHP) with high olefin selectivity and productivity. However, the loss of the boron component under a high concentration of water vapor and high temperature seriously hinders its further development. How to make h-BN a stable ODHP catalyst is one of the biggest scientific challenges at present. Herein, we construct h-BN⊃xIn2O3 composite catalysts through the atomic layer deposition (ALD) process. After high-temperature treatment in ODHP reaction conditions, the In2O3 nanoparticles (NPs) are dispersed on the edge of h-BN and observed to be encapsulated by ultrathin boron oxide (BOx) overlayer. A novel strong metal oxide-support interaction (SMOSI) effect between In2O3 NPs and h-BN is observed for the first time. The material characterization reveals that the SMOSI not only improves the interlayer force between h-BN layers with a pinning model but also reduces the affinity of the B-N bond toward O• for inhibiting oxidative cutting of h-BN into fragments at a high temperature and water-rich environment. With the pinning effect of the SMOSI, the catalytic stability of h-BN⊃70In2O3 has been extended nearly five times than that of pristine h-BN, and the intrinsic olefin selectivity/productivity of h-BN is well maintained.

Incorporating Binary Metal Oxides in Poly(ethylene oxide)-Based Solid Electrolytes by Vapor Phase Infiltration.

Vapor phase infiltration (VPI) derived from atomic layer deposition (ALD) enables inorganic materials to nucleate and grow within the free volume of polymers, which has shown promising prospects in the field of composite solid polymer electrolytes (CSPEs). However, there are only a few types of metal oxides that can be incorporated into the polymer matrix by VPI, let alone binary metal oxides, due to the limited knowledge of the VPI synthesis process. To combine the merits of different metal oxides, we investigate the VPI method to prepare ZnO-Al2O3 composites in poly(ethylene oxide) (PEO). When the introducing order is Al2O3/ZnO (AZO), due to the extremely high reactivity of trimethyl aluminum (TMA) with PEO, VPI-Al2O3 will accumulate near the surface of PEO. The surface Al2O3 layer inhibits the further diffusion of the diethyl zinc (DEZ) into the PEO matrix, leading to weak polymer-filler interactions and limited improvement of the Li+ conduction. In the incorporation order of ZnO/Al2O3 (ZAO), the moderate reactivity of DEZ renders the uniform distribution of VPI-ZnO within PEO, and the following TMA can both react with PEO and VPI-ZnO particles near the surface of PEO, which not only preserves the interactions between VPI-ZnO and PEO but also better inhibits the growth of lithium dendrites. The incorporation order plays a crucial role in the morphology and composition of binary metal oxides synthesized by VPI.

Insights into the Solid-State Synthesis of Defect-Rich Zr-UiO-66.

Metal-organic frameworks (MOFs), a new type of porous material, have shown many possible applications in gas storage and separation, biomedicine, catalysis, and so on. While most MOFs are synthesized through solvothermal synthesis where a large quantity of organic solvent is used, the green synthetic approach using a minimized amount of solvent is important to prevent irreversible environmental compacts. In this study, we successfully synthesized Zr-MOFs with SBUs (e.g., UiO-66 and MIL-140A) using a simple metal source and investigated the role of organic modulators in modulating the MOF structures during solid-state synthesis. Meanwhile, UiO-66 rich in defects synthesized via a solid-state conversion strategy shows good catalytic performance for the ring-opening of epoxides with alcohols. This work contributes to the understanding of the role of organic modulators in the solid-state synthesis of MOFs.

Synthesis of a Spatially Confined, Highly Durable, and Fully Exposed Pd Cluster Catalyst via Sequential Site-Selective Atomic Layer Deposition.

Bottom-up synthesis based on site-selective atomic layer deposition is a powerful atomic-scale processing approach to fabricate materials with desired functionalities. Typical selective atomic layer deposition (ALD) can be achieved using selective activation of a growth area or selective deactivation of a protected area. In this work, we explored the site selectivity based on the difference of the inherent surface reactivity between different materials and within the same materials. By sequentially applying two site-selective atomic layer deposition, the ALD Pd catalyst is spatially confined on ALD SnO2 modified h-BN substrate Pd/SnO2/h-BN shows improved catalytic activity and stability due to strong metal-support interactions and spatial confinement. The results reveal that sequential site-selective ALD is a feasible and effective synthesis strategy that provides an attractive path toward designing and developing highly stable catalysts.

An Ultrathin Functional Layer Based on Porous Organic Cages for Selective Ion Sieving and Lithium-Sulfur Batteries.

Thin films with effective ion sieving ability are highly desired in energy storage and conversion devices, including batteries and fuel cells. However, it remains challenging to design and fabricate cost-effective and easy-to-process ultrathin films for this purpose. Here, we report a 300 nm-thick functional layer based on porous organic cages (POCs), a new class of porous molecular materials, for fast and selective ion transport. This solution processable material allows for the design of thin films with controllable thickness and tunable porosity by tailoring cage chemistry for selective ion separation. In the prototype, the functional layer assembled by CC3 can selectively sieve Li+ ions and efficiently suppress undesired polysulfides with minimal sacrifice for the system's total energy density. Separators modified with POC thin films enable batteries with good cycle performance and rate capability and offer an attractive path toward the development of future high-energy-density energy storage devices.

Simultaneous Enhancement of Interfacial Stability and Kinetics of Single-Crystal LiNi0.6Mn0.2Co0.2O2 through Optimized Surface Coating and Doping.

Balancing interfacial stability and Li+ transfer kinetics through surface engineering is a key challenge in developing high-performance battery materials. Although conformal coating enabled by atomic layer deposition (ALD) has shown great promise in controlling impedance increase upon cycling by minimizing side reactions at the electrode-electrolyte interface, the coating layer itself usually exhibits poor Li+ conductivity and impedes surface charge transfer. In this work, we have shown that by carefully controlling postannealing temperature of an ultrathin ZrO2 film prepared by ALD, Zr4+ surface doping could be achieved for Ni-rich layered oxides to accelerate the charge transfer yet provide sufficient protection. Using single-crystal LiNi0.6Mn0.2Co0.2O2 as a model material, we have shown that surface Zr4+ doping combined with ZrO2 coating can enhance both the cycle performance and rate capability during high-voltage operation. Surface doping via controllable postannealing of ALD surface coating layer reveals an attractive path toward developing stable and Li+-conductive interfaces for single-crystal battery materials.

Surfactant-regulated fabrication of gold nanostars in magnetic core/shell hybrid nanoparticles for controlled release of drug.

Core-shell nanostructured materials, which are of great interest for fundamental research and industrial applications, have properties that can be enhanced by combining component superstructures. Here, we report the new construction of magnetic core-shell gold nanostars (AuNSs) for controlled release of drug. The AuNSs were successfully embedded intact between an inner silica layer and outside mesoporous silica layer to create magnetic core/shell hybrid nanoparticles by using a base cationic templating surfactant, cetyltrimethylammonium hydroxide (CTAOH). The core-shell nano-composites containing AuNSs exhibit the characteristics including high magnetization, mesoporous nanostructure, photothermal properties and low in vitro toxicity, showing the potential applications for drug delivery and controlled release.

Chitosan gel incorporated peptide-modified AuNPs for sustained drug delivery with smart pH responsiveness.

In this study, gold nanoparticles (AuNPs) were modified with a negatively charged peptide, Fmoc-GCE, for use as nanocarriers of a positively charged anti-tumor drug, doxorubicin hydrochloride (DOX). The Fmoc-GCE-modified AuNPs were further used to load DOX through electrostatic interaction. A temperature-sensitive gel, chitosan (CS) gel, was chosen to act as an appropriate platform to incorporate the modified AuNPs as a drug carrier. The incorporation of AuNPs makes the complex gel exhibit SERS characteristic, showing application prospects for the detection of cancer. More importantly, this drug delivery system with rather good biocompatibility can significantly extend the release time of the incorporated drugs and possesses pH responsiveness, exhibiting the advantages of controlled release and reduced side effects.