Non-stoichiometry and electrochemical properties of lithiated iron hydroxysulfides.

LiFeOHS is a material with Li2(OH)2 layers intercalated between Fe2S2 planes. Its hydrothermal synthesis in various concentrations of LiOH yields materials with a high non-stoichiometry of the Li/Fe ratio which can be explained by partial substitution of Li+ for Fe2+ in the Li2(OH)2 layers. Thermogravimetry, X-ray diffraction and Mössbauer studies indicate that the charge balance is obtained by substitution of hydroxyl ions OH- by oxide ions O2-. This material has been tested as an electrode for lithium-ion batteries against lithium metal. Specific capacities above 200 mA h g-1 at C/10 are achieved, involving 1 lithium per chemical formula when cycled between 1 V and 3 V vs. lithium. The first irreversible discharge leads to the insertion of one lithium atom and the evolution of hydrogen gas while iron remains in its +2-oxidation state. An original Li2OFeS oxysulfide is formed. The following reversible oxidation/reduction cycles involve the Fe3+/Fe2+ redox couple between the two limiting compositions: Li2OFeIIS and LiOFeIIIS.

Aqueous-Based Low-Temperature Synthesis and Thin-Film Properties of Oxysulfide BiCuOS Nanoparticles.

BiCuOS is a nontoxic p-type semiconductor that is a promising candidate for photoelectric applications. The formation of thin films with a good electronic transport at the grain boundaries, while avoiding thermal treatment detrimental to its chemical stability is a challenge. We have developed a chemical method for the direct synthesis of stable colloidal suspensions of BiCuOS nanoparticles from soluble precursors. These colloidal solutions were stabilized with a catechol functionalized poly-3-hexylthiophene that allows easy spin-coating deposition and favors electronic transport along the grain boundaries. Stacking of ZnO-BiCuOS layers were achieved, allowing preparation of n-p junctions. These act as rectifying diodes and are strongly photosensitive, with Iph /Idark =85 corresponding to an enhancement of the photocurrent of more than two orders of magnitude compared to that of BiCuOS alone. This energy-efficient and low-cost method is a further step in the development of new sulfide semiconductor devices.

Sorption of nickel and cobalt ions onto cobalt and nickel ferrites.

The corrosion of the metal parts in the primary circuit of pressurized water reactors leads to the release of colloidal particles (NiFe(2)O(4), CoFe(2)O(4), NiO, Ni...) and ionic species (Co, Ni, Cr...). Particles can interact with ionic species in the primary medium, contributing to their transport and to their deposition onto surfaces outside the neutron flux generating radioactive contamination. Sorption and zetametry experiments at 25 °C were performed on the Ni(2+)/CoFe(2)O(4) and Co(2+)/NiFe(2)O(4) systems in order to determine the behaviour of corrosion products in the fluid of the primary circuit. Sorption appears as surface complexation starting from pH 6 and is followed by precipitation of hydroxide above pH 7.5. Complexation and solubility constants were obtained from the modelling of sorption curves. The two oxide systems present a very similar sorption behaviour, but some differences, due to their different isoelectric points, could be observed on zetametric measurements.

Retention of fluoride ions from aqueous solution using porous hydroxyapatite. Structure and conduction properties.

Synthetic porous calcium hydroxyapatite (noted p-HAp) treated with different fluoride concentrations at room temperature in the presence of carbonate, sodium chloride and phosphate-rich media was investigated. The fluoridation rate of the porous calcium hydroxyapatite was 89% using 1 mol/L [F(-)] solution compared with 30% for crystalline hydroxyapatite (c-HAp). The high specific surface area of p-HAp (235 m(2)g(-1)) compared with c-HAp sample (47 m(2)g(-1)) has an important effect on the removal of fluoride ions from aqueous solution, when p-HAp was treated with high fluoride concentration to produce calcium fluorohydroxyapatite materials. Fluoride adsorption on porous hydroxyapatites (p-HAp) modified their structural and conduction properties.

Thin films of calcium phosphate and titanium dioxide by a sol-gel route: a new method for coating medical implants.

Titanium is a commonly used biomaterial for dental and orthopaedic applications. To increase its ability to bond with bone, some attempts were made to coat its surface with calcium phosphate (CaP). This paper describes a new type of coating. Instead of a pure CaP layer, a mixing of titanium dioxide (TIO2) and CaP is fabricated and deposited as a coating. These layers are deposited by a sol-gel route on pure titanium substrates using various pre-treatments. The method consists of mixing a solution of tetrabutyl ortho-titanate or a sol of titanium dioxide with a solution of calcium nitrate and phosphorous esters. This composite is deposited on to commercially pure titanium plates, mechanically polished or blasted with pure crystalline aluminum oxide, using the spin-coating technique. These coatings are then fired at 650 or 850 degrees C for various times. The samples are characterized by X-ray diffraction for their crystallinity, X-ray photoelectron spectroscopy for their surface chemical composition and scanning electron microscopy for their topography. Samples treated at 850 degrees C present a well-pronounced crystallinity, and a high chemical purity at the surface. The topography is strongly related to the viscosity of the precursor and the substrate pre-treatment. Possibilities to structure the outermost layer are presented.