Exploring zinc oxide morphologies for aqueous solar cells by a photoelectrochemical, computational, and multivariate approach.

Dye-sensitized solar cells assembled with aqueous electrolytes are emerging as a sustainable photovoltaic technology suitable for safe indoor and portable electronics use. While the scientific community is exploring unconventional materials for preparing electrodes and electrolytes, this work presents the first study on zinc oxide as a semiconductor material to fabricate photoanodes for aqueous solar cells. Different morphologies (i.e., nanoparticles, multipods, and desert roses) are synthesized, characterized, and tested in laboratory-scale prototypes. This exploratory work, also integrated by a computational study and a multivariate investigation on the factors that influence electrode sensitization, confirms the possibility of using zinc oxide in the field of aqueous photovoltaics and opens the way to new morphologies and processes of functionalization or surface activation to boost the overall cell efficiency.

Modulation of [CuOH/O]+ Properties in [2,2'-Bipyridine]2 Homoleptic Complexes through Substitution at the 6,6' Position by Methyl Groups.

In this paper, data from a DFT-based computational study on the reactivity of [Cu(2,2'-S-bpy)2]+PF6- (S indicating substitution by methyl groups at the 6 and/or 6' position and ranging from 0 to 100% through 50%) homoleptic complexes based toward tButOOH were presented. Computational results, supported by cyclic voltammetry analysis, prove the feasibility of finely tuning the chemical properties of the complexes and their reactivity by means of insertion of methyl moieties in selected positions within the bipyridine scaffold.

ZnO tetrapod morphology influence on UV sensing properties.

The aim of this work was to investigate how ZnO tetrapod (ZnO-T) morphology, structure, and surface charge properties (i.e. Debye length) influence their UV sensing properties, shedding light on the underlying photoresponse mechanisms. ZnO-Ts were synthesized and centrifuged to obtain three different fractions with tuned morphology, which were characterized by scanning electron microscopy, transmission electron microscopy, and high-resolution transmission electron microscopy microscopies, x-ray diffraction analysis, Brunauer-Emmett-Teller measurements, FTIR and UV-vis spectroscopies. ZnO-T UV sensors were fabricated and tested comparing among ZnO-T fractions and commercial ZnO nanoparticles. ZnO-T photoresponse was mostly influenced by ZnO-T leg diameter, with the optimal value close to the double Debye length. We also demonstrated how fractionating ZnO-Ts for morphology optimization can increased the responsivity by 2 orders of magnitude. Moreover, ZnO-T showed 3 orders of magnitude higher responsivity compared to commercial ZnO nanopowder. These results are beneficial for the engineering of efficient UV sensors and contribute to a deeper understanding the overall mechanism governing UV photoresponse.

Improving Sustainability through Covalent Adaptable Networks in the Recycling of Polyurethane Plastics.

The global plastic waste problem has created an urgent need for the development of more sustainable materials and recycling processes. Polyurethane (PU) plastics, which represent 5.5% of globally produced plastics, are particularly challenging to recycle owing to their crosslinked structure. Covalent adaptable networks (CANs) based on dynamic covalent bonds have emerged as a promising solution for recycling PU waste. CANs enable the production of thermoset polymers that can be recycled using methods that are traditionally reserved for thermoplastic polymers. Reprocessing using hot-pressing techniques, in particular, proved to be more suited for the class of polyurethanes, allowing for the efficient recycling of PU materials. This Review paper explores the potential of CANs for improving the sustainability of PU recycling processes by examining different types of PU-CANs, bond types, and fillers that can be used to optimise the recycling efficiency. The paper concludes that further research is needed to develop more cost-effective and industrial-friendly techniques for recycling PU-CANs, as they can significantly contribute to sustainable development by creating recyclable thermoset polymers.

Roadmap on thermoelectricity.

The increasing energy demand and the ever more pressing need for clean technologies of energy conversion pose one of the most urgent and complicated issues of our age. Thermoelectricity, namely the direct conversion of waste heat into electricity, is a promising technique based on a long-standing physical phenomenon, which still has not fully developed its potential, mainly due to the low efficiency of the process. In order to improve the thermoelectric performance, a huge effort is being made by physicists, materials scientists and engineers, with the primary aims of better understanding the fundamental issues ruling the improvement of the thermoelectric figure of merit, and finally building the most efficient thermoelectric devices. In this Roadmap an overview is given about the most recent experimental and computational results obtained within the Italian research community on the optimization of composition and morphology of some thermoelectric materials, as well as on the design of thermoelectric and hybrid thermoelectric/photovoltaic devices.

Quinoid-Thiophene-Based Covalent Organic Polymers for High Iodine Uptake: When Rational Chemical Design Counterbalances the Low Surface Area and Pore Volume.

A novel 2D covalent organic polymer (COP), based on conjugated quinoid-oligothiophene (QOT) and tris(aminophenyl) benzene (TAPB) moieties, is designed and synthesized (TAPB-QOT COP). Some DFT calculations are made to clarify the equilibrium between different QOT isomers and how they could affect the COP formation. Once synthetized, the polymer has been thoroughly characterized by spectroscopic (i.e., Raman, UV-vis), SSNMR and surface (e.g., SEM, BET) techniques, showing a modest surface area (113 m2 g-1) and micropore volume (0.014 cm3 g-1 with an averaged pore size of 5.6-8 Å). Notwithstanding this, TAPB-QOT COP shows a remarkably high iodine (I2) uptake capacity (464 %wt) comparable to or even higher than state-of-the-art porous organic polymers (POPs). These auspicious values are due to the thoughtful design of the polymer with embedded sulfur sites and a conjugated scaffold with the ability to counterbalance the relatively low pore volumes. Indeed, both morphological and Raman data, supported by computational analyses, prove the very high affinity between the S atom in our COP and the I2. As a result, TAPB-QOT COP shows the highest volumetric I2 uptake (i.e., the amount of I2 uptaken per volume unit) up to 331 g cm-3 coupled with a remarkably high reversibility (>80% after five cycles).

An Integrated Characterization Strategy on Board for Recycling of poly(vinyl butyral) (PVB) from Laminated Glass Wastes.

Polyvinyl butyral (PVB) is widely used as an interlayer material in laminated glass applications, mainly in the automotive industry, but also for construction and photovoltaic applications. Post-consumed laminated glass is a waste that is mainly landfilled; nevertheless, it can be revalorized upon efficient separation and removal of adhered glass. PVB interlayers in laminated glass are always plasticized with a significant fraction in the 20-40% w/w range of plasticizer, and they are protected from the environment by two sheets of glass. In this work, the aim is to develop a thorough characterization strategy for PVB films. Neat reference PVB grades intended for interlayer use are compared with properly processed (delaminated) post-consumed PVB grades from the automotive and construction sectors. Methods are developed to open opportunities for recycling and reuse of the latter. The plasticizer content and chemical nature are determined by applying well-known analytical techniques, namely, FT-IR, TGA, NMR. The issue of potential aging during the life cycle of the original laminated material is also addressed through NMR. Based on the findings, a sensor capable of directly sorting PVB post-consumer materials will be developed and calibrated at a later stage.

A multi-technique approach to unveil the redox behaviour and potentiality of homoleptic CuI complexes based on substituted bipyridine ligands in oxygenation reactions.

The effect of differently substituted 2,2'-bipyridine ligands (i.e. 6,6'-dimethyl-2,2'-bipyridine, 5,5'-dimethyl-2,2'-bipyridine, 6,6'-dimethoxy-2,2'-bipyridine and 2,2'-bipyridine) on the reversible oxidation of the resulting CuI homoleptic complexes is investigated by means of a multi-technique approach (electronic and vibrational spectroscopies, DFT, electrochemistry). Among the four tested complexes, [CuI(6,6'-dimethyl-2,2'-bipyridine)2] (PF6) shows a peculiar behavior when oxidized with an organic peroxide (i.e. tert-butyl hydroperoxide, tBuOOH). The simultaneous use of UV-Vis-NIR and Raman spectroscopy methods and cyclovoltammetry, supported by DFT based calculations, allowed identifying (i) the change in the oxidation state of the copper ion and (ii) some peculiar modification in the local structure of the metal leading to the formation of a [CuIIOH]+ species. The latter, being able to oxidize a model molecule (i.e. cyclohexene) and showing the restoration of the original CuI complex and the formation of cyclohexanone, confirms the potential of these simple homoleptic CuI complexes as model catalysts for partial oxygenation reactions.

Imidazo[1,5-a]pyridine-Based Fluorescent Probes: A Photophysical Investigation in Liposome Models.

Imidazo[1,5-a]pyridine is a stable scaffold, widely used for the development of emissive compounds in many application fields (e.g., optoelectronics, coordination chemistry, sensors, chemical biology). Their compact shape along with remarkable photophysical properties make them suitable candidates as cell membrane probes. The study of the membrane dynamics, hydration, and fluidity is of importance to monitor the cellular health and to explore crucial biochemical pathways. In this context, five imidazo[1,5-a]pyridine-based fluorophores were synthesized according to a one-pot cyclization between an aromatic ketone and benzaldehyde in the presence of ammonium acetate and acetic acid. The photophysical features of prepared compounds were investigated in several organic solvents and probes 2-4 exhibited the greatest solvatochromic behavior, resulting in a higher suitability as membrane probes. Their interaction with liposomes as artificial membrane model was tested showing a successful intercalation of the probes in the lipid bilayer. Kinetic experiments were carried out and the lipidic phase influence on the photophysical features was evaluated through temperature-dependent experiments. The results herein reported encourage further investigations on the use of imidazo[1,5-a]pyridine scaffold as fluorescent membrane probes.

Polymethine dyes-loaded solid lipid nanoparticles (SLN) as promising photosensitizers for biomedical applications.

Polymethine dyes (PMD) have proved to be excellent candidates in the biomedical field for potential applications in both diagnostic and therapeutic. However, PMD application in biomedicine is hindered by their poor solubility and stability in physiological conditions. Therefore, the incorporation of these dyes in nanosystems could be important to prevent the formation of dye aggregates in aqueous environment and to protect their photophysical characteristics. In the present work, two PMD based on the benzoindolenine ring (bromine benzo-cyanine-C4 and bromine benzo-squaraine-C4) were incorporated into Solid Lipid Nanoparticles (SLN) to solubilize and stabilize them in aqueous solutions. Obtained SLN showed a high incorporation efficiency for both PMD (≈90%) and not only preserved their spectroscopic properties in the NIR region even under physiological conditions but also improved them. Viability assays showed good biocompatibility of both empty and loaded nanocarriers while the cellular uptake and intracellular localization showed the effective internalization in MCF-7 cells, with a partial mitochondrial localization for CY-SLN. Moreover, in vitro phototoxicity assay showed that cyanine loaded-SLN (CY-SLN) is more photoactive than the free dye.

Multivariate Analysis Identifying [Cu(N

White light-emitting electrochemical cells (LECs) comprising only [Cu(N^N)(P^P)]+ have not been reported yet, as all the attempts toward blue-emitting complexes failed. Multivariate analysis, based on prior-art [Cu(N^N)(P^P)]+ -based thin-film lighting (>90 papers) and refined with computational calculations, identifies the best blue-emitting [Cu(N^N)(P^P)]+ design for LECs, that is, N^N: 2-(4-(tert-butyl)phenyl)-6-(3,5-dimethyl-1H-pyrazol-1-yl)pyridine and P^P: 4,5-bis(diphenylphosphino)-9,9-dimethylxanthene, to achieve predicted thin-film emission at 490 nm and device performance of 3.8 cd A-1 @170 cd m-2 . Validation comes from synthesis, X-ray structure, thin-film spectroscopic/microscopy/electrochemical characterization, and device optimization, realizing the first [Cu(N^N)(P^P)]+ -based blue-LEC with 3.6 cd A-1 @180 cd m-2 . This represents a record performance compared to the state-of-the-art tricoordinate Cu(I)-complexes blue-LECs (0.17 cd A-1 @20 cd m-2 ). Versatility is confirmed with the synthesis of the analogous complex with 2-(4-(tert-butyl)phenyl)-6-(3,5-dimethyl-1H-pyrazol-1-yl)pyrazine (N^N), showing a close prediction/experiment match: λ = 590/580 nm; efficiency = 0.55/0.60 cd A-1 @30 cd m-2 . Finally, experimental design is applied to fabricate the best white multicomponent host:guest LEC, reducing the number of trial-error attempts toward the first white all-[Cu(N^N)(P^P)]+ -LECs with 0.6 cd A-1 @30 cd m-2 . This corresponds to approximately ten-fold enhancement compared to previous LECs (<0.05 cd A-1 @<12 cd m-2 ). Hence, this work sets in the first multivariate approach to design emitters/active layers, accomplishing first-class [Cu(N^N)(P^P)]+ -based blue/white LECs that were previously elusive.

Transparent and Colorless Dye-Sensitized Solar Cells Exceeding 75% Average Visible Transmittance.

Most photovoltaic (PV) technologies are opaque to maximize visible light absorption. However, see-through solar cells open additional perspectives for PV integration. Looking beyond maximizing visible light harvesting, this work considers the human eye photopic response to optimize a selective near-infrared sensitizer based on a polymethine cyanine structure (VG20-C x ) to render dye-sensitized solar cells (DSSCs) fully transparent and colorless. This peculiarity was achieved by conferring to the dye the ability to strongly and sharply absorb beyond 800 nm (S0-S1 transition) while rejecting the upper S0-S n contributions far in the blue where the human retina is poorly sensitive. When associated with an aggregation-free anatase TiO2 photoanode, the selective NIR-DSSC can display 3.1% power conversion efficiency, up to 76% average visible transmittance (AVT), a value approaching the 78% AVT value of a standard double glazing window while reaching a color rendering index (CRI) of 92.1%. The ultrafast and fast charge transfer processes are herein discussed, clarifying the different relaxation channels from the dye monomer excited states and highlighting the limiting steps to provide future directions to enhance the performances of this nonintrusive NIR-DSSC technology.

Lignin-Based Polymer Electrolyte Membranes for Sustainable Aqueous Dye-Sensitized Solar Cells.

In the quest for sustainable materials for quasi-solid-state (QS) electrolytes in aqueous dye-sensitized solar cells (DSSCs), novel bioderived polymeric membranes were prepared in this work by reaction of preoxidized kraft lignin with poly(ethylene glycol)diglycidylether (PEGDGE). The effect of the PEGDGE/lignin relative proportions on the characteristics of the obtained membranes was thoroughly investigated, and clear structure-property correlations were highlighted. In particular, the glass transition temperature of the materials was found to decrease by increasing the amount of PEGDGE in the formulation, indicating that polyethylene glycol chains act as flexible segments that increase the molecular mobility of the three-dimensional polymeric network. Concurrently, their swelling ability in liquid electrolyte was found to increase with the concentration of PEGDGE, which was also shown to influence the ionic transport efficiency within the membrane. The incorporation of these lignin-based cross-linked systems as QS electrolyte frameworks in aqueous DSSCs allowed the preparation of devices with excellent long-term stability under UV-vis light, which were found to be superior to benchmark QS-DSSCs incorporating state-of-the-art carboxymethylcellulose membranes. This study provides the first demonstration of lignin-based QS electrolytes for stable aqueous DSSCs, establishing a straightforward strategy to exploit the potential of lignin as a functional polymer precursor for the field of sustainable photovoltaic devices.

Polymeric Dopant-Free Hole Transporting Materials for Perovskite Solar Cells: Structures and Concepts towards Better Performances.

Perovskite solar cells are a hot topic of photovoltaic research, reaching, in few years, an impressive efficiency (25.5%), but their long-term stability still needs to be addressed for industrial production. One of the most sizeable reasons for instability is the doping of the Hole Transporting Material (HTM), being the salt commonly employed as a vector bringing moisture in contact with perovskite film and destroying it. With this respect, the research focused on new and stable "dopant-free" HTMs, which are inherently conductive, being able to effectively work without any addition of dopants. Notwithstanding, they show impressive efficiency and stability results. The dopant-free polymers, often made of alternated donor and acceptor cores, have properties, namely the filming ability, the molecular weight tunability, the stacking and packing peculiarities, and high hole mobility in absence of any dopant, that make them very attractive and a real innovation in the field. In this review, we tried our best to collect all the dopant-free polymeric HTMs known so far in the perovskite solar cells field, providing a brief historical introduction, followed by the classification and analysis of the polymeric structures, based on their building blocks, trying to find structure-activity relationships whenever possible. The research is still increasing and a very simple polymer (PFDT-2F-COOH) approaches PCE = 22% while some more complex ones overcome 22%, up to 22.41% (PPY2).

Influence of start-up phase of an incinerator on inorganic composition and lead isotope ratios of the atmospheric PM10.

A municipal solid waste incinerator (MSWI) was installed in a peripheral area of the city of Turin. In this study, we evaluated the contribution of this plant to the massive concentration of PM10, to its chemical composition and to the distribution of the lead isotopes during the start-up phase.We assessed the inorganic composition of PM10 collected in the vicinity of the Turin incinerator by inductively coupled plasma atomic emission spectroscopy (ICP-AES), magnetic sector inductively coupled plasma mass spectrometer (SF-ICP-MS) and ion chromatography (IC). The lead isotope ratios in PM10 samples were determined by SF-ICP-MS by a method developed and optimized using experimental design approach. Element trends and data chemometric treatment evidence that the vehicular traffic, increased in this area due to the opening of the MSWI plant, and, to a lesser degree, the direct incinerator emissions influence As, Cd, Cr, Cu, Ba, Mo, Pb, Sn and Zn concentrations. As a whole, however, the element concentrations in PM10 and the Enrichment Factors (EFs) were comparable with the values reported for other urban sites and target pollutant concentrations of MSWI emissions, namely Cd, Cr, Cu and Pb, were lower than in PM10 emitted from older MSWIs. This confirms that incinerators of new installation have a lower impact on atmospheric PM10 composition thanks to stricter current legislation and up-to-date technologies. The lead isotope ratios investigation allowed to distinguish the diverse sources (crustal, vehicular traffic and MSWI) that influence lead concentration in PM10 collected near incinerator during start-up phase.

Thermosetting Polyurethane Resins as Low-Cost, Easily Scalable, and Effective Oxygen and Moisture Barriers for Perovskite Solar Cells.

Long-term stability of perovskite solar cells (PSCs) is one of the main issues to be solved for forthcoming commercialization of this technology. In this work, thermosetting polyurethane (PU)-based resins are proposed as effective encapsulants for perovskite solar cells to prevent degradation caused by both moisture and oxygen. Application consists of drop-casting the precursor mixture directly over the devices followed by in situ polymerization, avoiding the use of other adhesives. PUs are cost-effective, lightweight, thermal, and light-stable materials whose mechanical, chemical, and physical properties can be easily tuned by thoughtful choice of their precursor. Encapsulated PSCs show extremely good stability when stored under ambient light (maximum, 1000 lux), controlled humidity (28-65%), and temperature (18-30 °C) by retaining 94% of the initial power conversion efficiency after 2500 h (4 months), whereas control devices lose 90% of their performance after 500 h (T80 = 37 h); once stored according to ISOS-D-1, PU-protected devices showed T80 > 1200 h. Encapsulated devices are stable even when immersed in pure water. The demonstration of PUs as promising solution-processed encapsulant materials for PSCs can pave the way for these to become a cost-effective encapsulation route alternative for future industrialization of this technology.

Photoanodes for Aqueous Solar Cells: Exploring Additives and Formulations Starting from a Commercial TiO2 Paste.

Whereas the commercialization of dye-sensitized solar cells (DSSCs) is finally proceeding taking advantage of their low cost and tunable optical features, such as colour and transparency for both indoor and building-integrated applications, the corresponding aqueous counterpart is still at its infancy. As the TiO2 electrode is a fundamental component for hybrid solar cells, this work investigates the effect of different molecular (α-terpineol, propylene carbonate) and polymeric (polyethylene oxide, polyethylene glycol, carboxymethyl cellulose and xanthan gum) additives that can be introduced into a commercial TiO2 paste for for screen-printing (or doctor blade). Among all, the addition of polyethylene glycol leads to the best cell performances, with markedly increased short-circuit current density (+18 %) and power conversion efficiency (+48 %) with respect to the pristine (commercial) counterpart. When further explored at different concentration levels, electrodes fabricated from polyethylene glycol-based pastes show different morphologies, thicknesses and performances, which are investigated through (photo)electrochemical, structural, physical-chemical and microscopic techniques.

Hydrogel Electrolytes Based on Xanthan Gum: Green Route towards Stable Dye-Sensitized Solar Cells.

The investigation of innovative electrolytes based on nontoxic and nonflammable solvents is an up-to-date, intriguing challenge to push forward the environmental sustainability of dye-sensitized solar cells (DSSCs). Water is one of the best choices, thus 100% aqueous electrolytes are proposed in this work, which are gelled with xanthan gum. This well-known biosourced polymer matrix is able to form stable and easily processable hydrogel electrolytes based on the iodide/triiodide redox couple. An experimental strategy, also supported by the multivariate chemometric approach, is used here to study the main factors influencing DSSCs efficiency and stability, leading to an optimized system able to improve its efficiency by 20% even after a 1200 h aging test, and reaching an overall performance superior to 2.7%. In-depth photoelectrochemical investigation demonstrates that DSSCs performance based on hydrogel electrolytes depends on many factors (e.g., dipping conditions, redox mediator concentrations, etc.), that must be carefully quantified and correlated in order to optimize these hydrogels. Photovoltaic performances are also extremely reproducible and stable in an open cell filled in air atmosphere, noticeably without any vacuum treatments.

Squaraine dyes as fluorescent turn-on sensors for the detection of porcine gastric mucin: A spectroscopic and kinetic study.

Mucin-type glycoproteins are the principal components of mucus which cover all the mucosal surfaces of the human body. The mucus and mucins are essential mediators of the innate immune system, however in the last decades mucins have been identified even as an important class of cancer biomarkers. Luminogenic materials with fluorescence turn-on behavior are becoming promising materials because of their advantages of label free, relatively inexpensive and simple to use properties for biological detection and imaging. Squaraines are luminogens characterized by high fluorescence in organic media but poor emission in aqueous environments due to their tendency to self-aggregate. Herein we investigate the interaction between porcine gastric mucin (PGM) and several squaraines in aqueous media. While squaraine dyes showed low fluorescence intensity and quantum yield in water, as a result of the formation of aggregates, an enhancement of fluorescence up to 45-fold was achieved when PGM was added. PGM was detected in a linear range of 10-300 µg/mL with a limit of detection of 800 ng/mL. The assay was used to quantify mucin in diluted human serum samples and recoveries of 94.9-116.2% were achieved. To the best of our knowledge, this is the easiest and convenient method for mucin detection in the reported literature.

A water-based and metal-free dye solar cell exceeding 7% efficiency using a cationic poly(3,4-ethylenedioxythiophene) derivative.

A green, efficient and stable solar cell based only on water and safe and cheap elements of the periodic table is proposed in this work, finally consolidating (also from a sustainability viewpoint) the concept of "artificial photosynthesis" studied for decades by the scientific community. The concept of dye-sensitized solar cells is re-proposed here with a metal-free organic dye, an iodine-based electrolyte in a 100% aqueous environment and a new cathode (cationic PEDOT) synthesized for the first time with the aim of inhibiting the repulsion between the anions of redox couples and the PEDOT:PSS matrix commonly used as the counter-electrode. This elegant setup leads to a record efficiency of 7.02%, the highest value ever obtained for a water-based solar cell and, in general, for a photovoltaic device free of both organic solvents and expensive/heavy metals.