Surfactant Engineering and Its Role in Determining the Performance of Nanoparticulate Organic Photovoltaic Devices.

The fabrication of organic photovoltaics (OPVs) from non-hazardous nanoparticulate (NP) inks offers considerable promise for the development of eco-friendly large-scale printed solar modules. However, the typical NP core-shell morphology (driven by the different donor/acceptor affinities for the surfactant used in NP synthesis) currently hinders the photovoltaic performance. As such, surfactant engineering offers an elegant approach to synthesizing a more optimal intermixed NP morphology and hence an improved photovoltaic performance. In this work, the morphology of conventional sodium dodecyl sulfate (SDS) and 2-(3-thienyl) ethyloxybutylsulfonate (TEBS)-stabilized poly(3-hexylthiophene) (P3HT) donor:phenyl-C61-butyric acid methyl ester (PC61BM) acceptor NPs is probed using scanning transmission X-ray microscopy, UV-vis spectroscopy, grazing-incidence X-ray diffraction, and scanning electron microscopy. While the SDS-stabilized NPs exhibit a size-independent core-shell morphology, this work reveals that TEBS-stabilized NPs deliver an intermixed morphology, the extent of which depends on the particle size. Consequently, by optimizing the TEBS-stabilized NP size and distribution, NP-OPV devices with a power conversion efficiency that is ∼50% higher on average than that of the corresponding SDS-based NP-OPV devices are produced.

Controlling Nanostructure in Inkjet Printed Organic Transistors for Pressure Sensing Applications.

This work reports the development of a highly sensitive pressure detector prepared by inkjet printing of electroactive organic semiconducting materials. The pressure sensing is achieved by incorporating a quantum tunnelling composite material composed of graphite nanoparticles in a rubber matrix into the multilayer nanostructure of a printed organic thin film transistor. This printed device was able to convert shock wave inputs rapidly and reproducibly into an inherently amplified electronic output signal. Variation of the organic ink material, solvents, and printing speeds were shown to modulate the multilayer nanostructure of the organic semiconducting and dielectric layers, enabling tuneable optimisation of the transistor response. The optimised printed device exhibits rapid switching from a non-conductive to a conductive state upon application of low pressures whilst operating at very low source-drain voltages (0-5 V), a feature that is often required in applications sensitive to stray electromagnetic signals but is not provided by conventional inorganic transistors and switches. The printed sensor also operates without the need for any gate voltage bias, further reducing the electronics required for operation. The printable low-voltage sensing and signalling system offers a route to simple low-cost assemblies for secure detection of stimuli in highly energetic systems including combustible or chemically sensitive materials.

Building intermixed donor-acceptor architectures for water-processable organic photovoltaics.

A modified synthesis method for aqueous nanoparticle printing inks, based upon vacuum-assisted solvent removal, is reported. Poly(3-hexylthiophene):phenyl C61 butyric acid methyl ester nanoparticle inks were prepared via this modified miniemulsion method, leading to both an improvement in photoactive layer morphology and a substantial reduction in the ink fabrication time. A combination of UV-visible spectroscopy, photoluminescence spectroscopy and scanning transmission X-ray microscopy measurements revealed a nanoparticle morphology comprising highly intermixed donor-acceptor domains. Consistent with these measurements, dynamic mechanical thermal analysis of the nanoparticles showed a glass transition temperature (Tg) of 104 °C, rather than a pure polymer phase or pure fullerene phase Tg. Together the spectroscopy, microscopy and thermomechanical data indicate that rapid solvent removal generates a more blended nanoparticle morphology. As such, this study highlights a new experimental lever for optimising nanostructure in the photoactive layer of nanoparticulate organic photovoltaic devices by enabling highly intermixed donor-acceptor architectures to be built from customised nanoparticulate inks.

Roll-to-roll solvent annealing of printed P3HT : ICXA devices.

Currently, large-scale roll-to-roll production of printed organic photovoltaics (OPVs) involves high temperature annealing steps that are not compatible with thermally sensitive substrates, such as coated fabrics. In particular, the processing temperatures needed to produce the required crystalline ordering in the printed films are typically above the deformation and melting-points of these substrates. In this paper we investigate the use of local solvent recrystallisation (solvent annealing) on the roll-to-roll scale as a method for avoiding high-temperature thermal annealing. Solvent annealing was performed by slot-die coating a mixture of chloroform and methanol over a previously printed P3HT ICXA active layer film. Peak device performance was found for the 30% chloroform/70% methanol annealing case which increased device performance by a factor of 4 over the not treated devices.

Optimisation of purification techniques for the preparation of large-volume aqueous solar nanoparticle inks for organic photovoltaics.

In this study we have optimised the preparation conditions for large-volume nanoparticle inks, based on poly(3-hexylthiophene) (P3HT):indene-C60 multiadducts (ICxA), through two purification processes: centrifugal and crossflow ultrafiltration. The impact of purification is twofold: firstly, removal of excess sodium dodecyl sulfate (SDS) surfactant from the ink and, secondly, concentration of the photoactive components in the ink. The removal of SDS was studied in detail both by a UV-vis spectroscopy-based method and by surface tension measurements of the nanoparticle ink filtrate; revealing that centrifugal ultrafiltration removed SDS at a higher rate than crossflow ultrafiltration even though a similar filter was applied in both cases (10,000 Da Mw cut-off). The influence of SDS concentration on the aqueous solar nanoparticle (ASNP) inks was investigated by monitoring the surface morphology/topography of the ASNP films using atomic force microscopy (AFM) and scanning electron microscopy (SEM) and photovoltaic device performance as a function of ultrafiltration (decreasing SDS content). The surface morphology/topography showed, as expected, a decreased number of SDS crystallites on the surface of the ASNP film with increased ultrafiltration steps. The device performance revealed distinct peaks in efficiency with ultrafiltration: centrifuge purified inks reached a maximum efficiency at a dilution factor of 7.8 × 104, while crossflow purified inks did not reach a maximum efficiency until a dilution factor of 6.1 × 109. This difference was ascribed to the different wetting properties of the prepared inks and was further corroborated by surface tension measurements of the ASNP inks which revealed that the peak efficiencies for both methods occurred for similar surface tension values of 48.1 and 48.8 mN m-1. This work demonstrates that addressing the surface tension of large-volume ASNP inks is key to the reproducible fabrication of nanoparticle photovoltaic devices.

Utilizing Energy Transfer in Binary and Ternary Bulk Heterojunction Organic Solar Cells.

Energy transfer has been identified as an important process in ternary organic solar cells. Here, we develop kinetic Monte Carlo (KMC) models to assess the impact of energy transfer in ternary and binary bulk heterojunction systems. We used fluorescence and absorption spectroscopy to determine the energy disorder and Förster radii for poly(3-hexylthiophene-2,5-diyl), [6,6]-phenyl-C61-butyric acid methyl ester, 4-bis[4-(N,N-diisobutylamino)-2,6-dihydroxyphenyl]squaraine (DIBSq), and poly(2,5-thiophene-alt-4,9-bis(2-hexyldecyl)-4,9-dihydrodithieno[3,2-c:3',2'-h][1,5]naphthyridine-5,10-dione). Heterogeneous energy transfer is found to be crucial in the exciton dissociation process of both binary and ternary organic semiconductor systems. Circumstances favoring energy transfer across interfaces allow relaxation of the electronic energy level requirements, meaning that a cascade structure is not required for efficient ternary organic solar cells. We explain how energy transfer can be exploited to eliminate additional energy losses in ternary bulk heterojunction solar cells, thus increasing their open-circuit voltage without loss in short-circuit current. In particular, we show that it is important that the DIBSq is located at the electron donor-acceptor interface; otherwise charge carriers will be trapped in the DIBSq domain or excitons in the DIBSq domains will not be able to dissociate efficiently at an interface. KMC modeling shows that only small amounts of DIBSq (<5% by weight) are needed to achieve substantial performance improvements due to long-range energy transfer.

Comparative degradation and regeneration of polymer solar cells with different cathodes.

A comparative degradation study of solar cells based on a bulk-heterojunction (BHJ) blend of poly(3-hexylethiophene) (P3HT) and phenyl [6,6] C61 butyric acid methyl ester (PCBM) with two different cathodes is reported. Poly(ethylene-dioxythiphene):poly(styrene sulfonate) (PEDOT:PSS) coated ITO electrodes were used as the anode, whereas Ca/Al and Ca/Ag electrodes were used as cathodes. Fully degraded devices were subjected to thermal annealing under inert atmosphere. The performance of degraded solar cells with a Ca/Al cathode exhibited no improvement after treatment. However the solar cells with a Ca/Ag cathode exhibited a considerable recovery in their performance following annealing under a nitrogen atmosphere. Indeed, these solar cells could be subjected to many degradation and regeneration cycles. Current density-voltage (J-V) characteristics and X-ray photoelectron spectroscopy (XPS) studies show that this behavior arises from the complex chemical thermodynamics of the reactions that can occur at the cathode/active layer interface. In particular, the recovery of device performance for solar cells with a Ca/Ag cathode is due to the reversible oxidation of Ag upon thermal annealing.

Water-based nanoparticulate solar cells using a diketopyrrolopyrrole donor polymer.

Organic photovoltaic devices with either bulk heterojunction (BHJ) or nanoparticulate (NP) active layers have been prepared from a 1 : 2 blend of (poly{3,6-dithiophene-2-yl-2,5-di(2-octyldodecyl)-pyrrolo[3,4-c]pyrrole-1,4-dione-alt-naphthalene}) (PDPP-TNT) and the fullerene acceptor, ([6,6]-phenyl C71-butyric acid methyl ester) (PC70BM). Atomic force microscopy (AFM) and scanning electron microscopy (SEM) have been used to investigate the morphology of the active layers of the two approaches. Mild thermal treatment of the NP film is required to promote initial joining of the NPs in order for the devices to function, however the NP structure is retained. Consequently, whereas gross phase segregation of the active layer occurs in the BHJ device spin cast from chloroform, the nanoparticulate approach retains control of the material domain sizes on the length scale of exciton diffusion in the materials. As a result, NP devices are found to generate more than twice the current density of BHJ devices and have a substantially greater overall efficiency. The use of aqueous nanoparticulate dispersions offers a promising approach to control the donor acceptor morphology on the nanoscale with the benefit of environmentally-friendly, solution-based fabrication.

Organic solar cells: understanding the role of Förster resonance energy transfer.

Organic solar cells have the potential to become a low-cost sustainable energy source. Understanding the photoconversion mechanism is key to the design of efficient organic solar cells. In this review, we discuss the processes involved in the photo-electron conversion mechanism, which may be subdivided into exciton harvesting, exciton transport, exciton dissociation, charge transport and extraction stages. In particular, we focus on the role of energy transfer as described by F¨orster resonance energy transfer (FRET) theory in the photoconversion mechanism. FRET plays a major role in exciton transport, harvesting and dissociation. The spectral absorption range of organic solar cells may be extended using sensitizers that efficiently transfer absorbed energy to the photoactive materials. The limitations of F¨orster theory to accurately calculate energy transfer rates are discussed. Energy transfer is the first step of an efficient two-step exciton dissociation process and may also be used to preferentially transport excitons to the heterointerface, where efficient exciton dissociation may occur. However, FRET also competes with charge transfer at the heterointerface turning it in a potential loss mechanism. An energy cascade comprising both energy transfer and charge transfer may aid in separating charges and is briefly discussed. Considering the extent to which the photo-electron conversion efficiency is governed by energy transfer, optimisation of this process offers the prospect of improved organic photovoltaic performance and thus aids in realising the potential of organic solar cells.

Scanning transmission x-ray microscopy of polymer nanoparticles: probing morphology on sub-10 nm length scales.

Water-processable nanoparticle dispersions of semiconducting polymers offer an attractive approach to the fabrication of organic electronic devices since they offer: (1) control of nanoscale morphology and (2) environmentally friendly fabrication. Although the nature of phase segregation in these polymer nanoparticles is critical to device performance, to date there have been no techniques available to directly determine their intra-particle structure, which consequently has been poorly understood. Here, we present scanning transmission x-ray microscopy (STXM) compositional maps for nanoparticles fabricated from poly(9,9-dioctyl-fluorene-2,7-diyl-co-bis-N, N'-(4-butylphenyl)-bis-N, N'-phenyl-1,4-phenylenedi-amine) (PFB) and poly(9,9-dioctylfluorene-2,7-diyl-co-benzothiadiazole) (F8BT) 1:1 blend mixtures. The images show distinct phase segregation within the nanoparticles. The compositional data reveals that, within these nanoparticles, PFB and F8BT segregate into a core-shell morphology, with an F8BT-rich core and a PFB-rich shell. Structural modelling demonstrates that the STXM technique is capable of quantifying morphological features on a sub-10 nm length scale; below the spot size of the incident focused x-ray beam. These results have important implications for the development of water-based 'solar paints' fabricated from microemulsions of semiconducting polymers.

Colourimetric carboxylate anion sensors derived from viologen-based receptors.

A series of tri- and tetrapodal viologen-based anion receptors showing a colourimetric response to carboxylates, such as acetate, have been synthesised. Alteration of the anion binding sites allows for binding site competition within a receptor. This results in a delayed colourimetric response for urea derivatives compared with pyridinium systems because the anions are initially bound to the periphery of the receptor, away from the viologen unit. DFT calculations and experimental measurements allow the colour change to be assigned to an anion-receptor charge-transfer process, facilitated by the exceptionally low reduction potential of the cationic host compounds. Evidence for electron transfer to give the viologen radical cation is also seen in some cases.

Porphyrin complexes containing coordinated BOB groups: synthesis, chemical reactivity and the structure of [BOB(tpClpp)]2+.

The reactions of boron halides with free base porphyrins under conditions where partial hydrolysis of the boron halides can occur give diboron porphyrin complexes containing BOB moieties in which each boron is bonded to two porphyrin nitrogen atoms. BF(3).OEt(2) with H(2)(por) gives B(2)OF(2)(por) (por = tpp, ttp, tpClpp, oep) which has an asymmetric structure in which one boron lies in the porphyrin plane (B(ip)) while the other lies above it (B(oop)). BCl(3).MeCN with H(2)(por) gives B(2)O(2)(BCl(3))(2)(por) which contains a four-membered B(2)O(2) ring and is stable only in the presence of excess BCl(3). BBr(3) with Li(2)(tpClpp) gives the dicationic complex [B(2)O(tpClpp)](2+) as its [BBr(4)](-) salt, and is the first example of a boron porphyrin containing three-coordinate boron to be structurally characterised. B(2)O(2)(BCl(3))(2)(por) can be chromatographed on basic alumina to give the hydroxyboron complex B(2)O(OH)(2)(por), which is deduced from its NMR spectra and DFT calculations to have a structure analogous to B(2)OF(2)(por). The OH protons are shifted upfield to near delta -4 (B(oop)-OH) and -10 (B(ip)-OH) by the diamagnetic porphyrin ring current. The reaction of either B(2)O(2)(BCl(3))(2)(por) or B(2)O(OH)(2)(por) (por = ttp, tpClpp) with alcohols (ROH, R = Et, 4-C(6)H(4)CH(3)) gives B(2)O(OR)(2)(por), which can in turn be converted to B(2)O(OR)(OH)(por) by repeated chromatography. The reaction of PhBCl(2) with H(2)(por) (por = ttp, tpClpp) gives B(2)O(Ph)(OH)(por) which has been characterised by spectroscopy in concert with DFT calculations. It is a further example of the B(2)OF(2)(por) structural type, in which the phenyl group is coordinated to the out-of-plane boron and the OH group to the in-plane boron, as are its derivatives B(2)O(Ph)(X)(tpClpp) (X = F, OEt). Steric drivers for the facile hydrolysis of haloboron porphyrins relative to their dipyrromethene and expanded porphyrin counterparts are discussed.

Nanoscale quantitative chemical mapping of conjugated polymer blends.

Utilizing scanning transmission X-ray microscopy (STXM), we present a quantitative chemical analysis of the bulk composition of spin-coated blends of poly(9,9-dioctylfluorene-co-N-(4-butylphenyl)diphenylamine) (TFB) and poly(9,9'-dioctylfluorene-co-benzothiadiazole) (F8BT) used in efficient polymer light emitting diodes. With a lateral resolution of 50 nm, we reveal nanoscale subsurface chemical structure and show that in particular while blend composition remains constant within the TFB-rich domain, in the F8BT-rich phase there is an enrichment of F8BT at the domain interface.

Pyridinium CH...anion and pi-stacking interactions in modular tripodal anion binding hosts: ATP binding and solid-state chiral induction.

The preparation of two new tripodal "pinwheel" type anion hosts based on a triethylbenzene core and bipyridinium or ethylnicotinium arms is reported. The new materials bind anions via CH...anion interactions. Complexes with Br(-) and PF(6)(-) have been characterised by X-ray crystallography as both solvates in a pure form. In the bipyridinium host CH...F interactions to PF(6)(-) induce a chiral C(3) symmetric conformation that is disrupted in the hydrate. The compound is also selective for ATP(2-) in aqueous acetonitrile.

Slow anion exchange, conformational equilibria, and fluorescent sensing in venus flytrap aminopyridinium-based anion hosts.

The synthesis, anion binding, and conformational properties of a series of 3-aminopyridinium-based, tripodal, tricationic hosts for anions are described. Slow anion and conformational exchange on the (1)H NMR time scale at low temperature, coupled with NMR titration, results in a high level of understanding of the anion-binding properties of the compounds, particularly with respect to significant conformational change resulting from induced fit complexation. Peak selectivity for halides, particularly Cl(-), is observed. The approach has been extended to dipodal and tripodal podands based on 3-aminopyridinium "arms" containing photoactive anthracenyl moieties. The 1,3,5-tripodal host shows a remarkable selectivity for acetate over other anions, in contrast to the analogous unsubstituted tris(3-aminopyridinium) analogue, despite the fact that low-temperature (1)H NMR experiments reveal a total of four acetate-binding conformations. Photodimerization of anthracene units results in the formation of potential fluorescent anion sensors.

Channel-containing 1D coordination polymers based on a linear dimetallic spacer.

A new channel-containing 1D coordination polymer has been prepared by the combination of a linear dimetallic spacer, Cu2(O2CMe)4, and a linear didentate ligand, 1,3-di-4-pyridylpropane; the new material includes methanol, acetic acid and diethylene glycol.

Anion sensing 'venus flytrap' hosts: a modular approach.

A series of podands based on three hydrogen bonding 'arms' have been prepared and their affinities for simple inorganic anions measured.

Cooperative anion binding and electrochemical sensing by modular podands.

A series of podands based on two or three hydrogen bonding "arms" situated in mutually ortho, meta, or para relationships about an aryl core have been prepared, and their affinities for simple inorganic anions were measured. Of the two-arm hosts the meta compound and to a lesser extent the ortho host exhibit a cooperative anion binding effect. The two arms function essentially independently in the para derivative. The mutually meta three-arm host shows dramatically enhanced cooperative binding. Conformational changes within the meta two-arm host result in significantly enhanced electrochemical anion sensing compared with the more conformationally rigid three-arm host.

A Porphyrin as a Binucleating Ligand: Preparation and Crystal Structure of a Porphyrin Complex Containing a Coordinated B2 O2 Ring.

A new coordination mode for the porphyrin ligand is found in [B2 O2 (BCl3 )2 (tpClpp)] (tpClpp=dianion of 5,10,15,20-tetra-p-chlorophenylporphyrin; the p-chlorophenyl groups are omitted for clarity in the picture shown on the right). This complex contains a four-membered B2 O2 ring in the cavity of the ligand. The two boron atoms are coplanar with the porphyrin molecule, which undergoes an elongation along the B⋅⋅⋅B axis to accomodate the unusual guest.