Isolation and identification of carbon monoxide producing microorganisms from compost.

Carbon monoxide (CO) formation has been observed during composting of various fractions of organic waste. It was reported that this production can be biotic, associated with the activity of microorganisms. However, there are no sources considering the microbial communities producing CO production in compost. This preliminary research aimed to isolate and identify microorganisms potentially responsible for the CO production in compost collected from two areas of the biowaste pile: with low (118 ppm) and high CO concentration (785 ppm). Study proved that all isolates were bacterial strains with the majority of rod-shaped Gram-positive bacteria. Both places can be inhabited by the same bacterial strains, e.g. Bacillus licheniformis and Paenibacillus lactis. The most common were Bacillus (B. licheniformis, B. haynesii, B. paralicheniformis, and B. thermolactis). After incubation of isolates in sealed bioreactors for 4 days, the highest CO levels in the headspace were recorded for B. paralicheniformis (>1000 ppm), B. licheniformis (>800 ppm), and G. thermodenitrificans (∼600 ppm). High CO concentrations were accompanied by low O2 (<6%) and high CO2 levels (>8%). It is recommended to analyze the expression of the gene encoding CODH to confirm or exclude the ability of the identified strains to convert CO2 to CO.

Navigating Pyrolysis Implementation-A Tutorial Review on Consideration Factors and Thermochemical Operating Methods for Biomass Conversion.

Pyrolysis and related thermal conversion processes have shown increased research momentum in recent decades. Understanding the underlying thermal conversion process principles alongside the associated/exhibited operational challenges that are specific to biomass types is crucial for beginners in this research area. From an extensive literature search, the authors are convinced that a tutorial review that guides beginners particularly towards pyrolysis implementation, from different biomasses to the thermal conversion process and conditions, is scarce. An effective understanding of pre-to-main pyrolysis stages, alongside corresponding standard methodologies, would help beginners discuss anticipated results. To support the existing information, therefore, this review sought to seek how to navigate pyrolysis implementation, specifically considering factors and thermochemical operating methods for biomass conversion, drawing the ideas from: (a) the evolving nature of the thermal conversion process; (b) the potential inter-relatedness between individual components affecting pyrolysis-based research; (c) pre- to post-pyrolysis' engagement strategies; (d) potential feedstock employed in the thermal conversion processes; (e) the major pre-treatment strategies applied to feedstocks; (f) system performance considerations between pyrolysis reactors; and (g) differentiating between the reactor and operation parameters involved in the thermal conversion processes. Moreover, pre-pyrolysis activity tackles biomass selection/analytical measurements, whereas the main pyrolysis activity tackles treatment methods, reactor types, operating processes, and the eventual product output. Other areas that need beginners' attention include high-pressure process reactor design strategies and material types that have a greater potential for biomass.

Optimizing hydrothermal treatment for sustainable valorization and fatty acid recovery from food waste.

This study employs response surface methodology and a central composite design (CCD) to optimize hydrothermal treatment (HTT) conditions for the valorization of food waste (FW). Lab-scale pressure reactor-based HTT processes are investigated to detect the effects of temperature (220-340 °C) and resident time (90-260 min) on elemental composition and fatty acid recovery in the hydrothermal liquid. Central to the study is the identification of temperature as the primary factor influencing food waste conversion during the HTT process, showcasing its impact on HTT product yields. The liquid fraction, rich in saturated fatty acids (SFA), demonstrates a temperature-dependent trend, with higher temperatures favoring SFA recovery. Specifically, HTT at 340 °C in 180 min exhibits the highest SFA percentages, reaching up to 52.5 wt%. The study establishes HTT as a promising avenue for nutrient recovery, with the liquid fraction yielding approximately 95% at optimized conditions. Furthermore, statistical analysis using response surface methodology predicts the optimal achievable yields for hydrochar and hydrothermal liquid at 6.15% and 93.85%, respectively, obtained at 320 °C for 200 min.

Impact of using glucose as a sole carbon source to analyze the effect of biochar on the kinetics of biomethane production.

The adaptation of biochar in anaerobic digestion (AD) positively influences the conversion of substrate to biomethane and promotes system stability. This study investigated the influence of biochar (BC) doses (0 to 8 g/L) on the Biochemical Methane Potential (BMP) of glucose during a 60-day AD in a mesophilic batch-type reactor. The first 6.5 weeks of the experimentation were dedicated to the microorganism's adaptation to the biochar and degradation of organics from the used inoculum (3 phases of the glucose feeding). The last 2 weeks (4th phase of glucose feeding) represented the assumption, that glucose is the sole carbon source in the system. A machine learning model based on the autoregressive integrated moving average (ARIMA) method was used to model the cumulative BMP. The results showed that the BMP increased with the amount of BC added. The highest BMP was obtained at a dose of 8 g/L, with a maximum cumulative BMP of 390.33 mL CH4/g-VS added. Likewise, the system showed stability in the pH (7.17 to 8.17). In contrast, non-amended reactors produced only 135.06 mL CH4/g-VS and became acidic at the end of the operation. Reducing the influence of carbon from inoculum, sharpened the positive effect of BC on the kinetics of biomethane production from glucose.

Utilization of Plant Oils for Sustainable Polyurethane Adhesives: A Review.

The utilization of plant oils as a renewable resource for the production of polyurethane adhesives presents a promising way to improve sustainability and reduce environmental impact. This review explores the potential of various vegetable oils, including waste oils, in the synthesis of polyurethanes as an alternative to conventional petroleum-based raw materials. The investigation highlights the environmental challenges associated with conventional polyurethane production and highlights the benefits of switching to bio-renewable oils. By examining the feasibility and potential applications of vegetable oil-based polyurethanes, this study emphasizes the importance of further research and development in this area to realize the full potential of sustainable polyurethane adhesives. Further research and development in this area are key to overcoming the challenges and realizing the full potential of plant-oil-based polyurethanes in various industrial applications.

Enhancing municipal solid waste leachate treatment efficiency: AI-based prediction of electrocoagulation/flocculation recovery using iron electrodes.

This study addresses a gap in municipal leachate (MUPL) treatment by introducing a pioneering application of artificial intelligence (AI) in the electrocoagulation/electroflocculation (EC/EF) process utilizing iron electrodes. The overarching aim is to demonstrate the efficacy of AI, particularly a multi-layer perceptron (MLP)-based feed-forward artificial neural network (ANN) incorporating the Levenberg-Marquardt (LMb) algorithm, in predicting and optimizing EC/EF outcomes for turbidity (TDY) removal. The research methodology involved experimentation and robust ANN data modeling. The significance of this work emerges from the successful integration of AI, showcasing its potential in advancing wastewater, demonstrated through a strong positive correlation (0.994) between the ANN model predictions and experimental outcomes. The study achieves a remarkable 99.4% TDY removal at an electrolysis time of 10 min and contributes valuable insights into the critical parameters influencing the EC/EF process. Results from the ANN modeling exhibit high predictive accuracy, supported by elevated R-squared values and minimal mean square error. Statistical analyses underscore the significance of key process parameters, highlighting the influential roles of current intensity and settling time. The study emphasized the favourable impact of maintaining an acidic pH range, as it reduced electrostatic repulsion between particles, facilitating pollutant agglomeration, and identified electrolysis time as a key factor in enhancing treatment efficiency, supported by a strong positive correlation between electrolysis time and TDY reduction. Energy cost savings were realized by not requiring temperature elevation. Achieving a 99.4% TDY removal translates to substantial reductions in other pollutants present in the MUPL, thereby elevating water quality and ensuring compliance.

Recycled Waste as Polyurethane Additives or Fillers: Mini-Review.

The intensive development of the polyurethanes industry and limited resources (also due to the current geopolitical situation) of the raw materials used so far force the search for new solutions to maintain high economic development. Implementing the principles of a circular economy is an approach aimed at reducing the consumption of natural resources in PU production. This is understood as a method of recovery, including recycling, in which waste is processed into PU, and then re-used and placed on the market in the form of finished sustainable products. The effective use of waste is one of the attributes of the modern economy. Around the world, new ways to process or use recycled materials for polyurethane production are investigated. That is why innovative research is so important, in which development may change the existing thinking about the form of waste recovery. The paper presents the possibilities of recycling waste (such as biochar, bagasse, waste lignin, residual algal cellulose, residual pineapple cellulose, walnut shells, silanized walnut shells, basalt waste, eggshells, chicken feathers, turkey feathers, fiber, fly ash, wood flour, buffing dust, thermoplastic elastomers, thermoplastic polyurethane, ground corncake, Tetra Pak®, coffee grounds, pine seed shells, yerba mate, the bark of Western Red Cedar, coconut husk ash, cuttlebone, glass fibers and mussel shell) as additives or fillers in the formulation of polyurethanes, which can partially or completely replace petrochemical raw materials. Numerous examples of waste applications of one-component polyurethanes have been given. A new unexplored niche for the research on waste recycling for the production of two components has been identified.

Assessment of emissions and potential occupational exposure to carbon monoxide during biowaste composting.

To date, only a few studies focused on the carbon monoxide (CO) production during waste composting; all targeted on CO inside piles. Here, the CO net emissions from compost piles and the assessment of worker's occupational risk of exposure to CO at large-scale composting plants are shown for the first time. CO net emissions were measured at two plants processing green waste, sewage sludge, or undersize fraction of municipal solid waste. Effects of the location of piles (hermetised hall vs. open yard) and turning (before vs. after) were studied. Higher CO net emission rates were observed from piles located in a closed hall. The average CO flux before turning was 23.25 and 0.60 mg‧m-2‧h-1 for hermetised and open piles, respectively, while after- 69.38 and 5.11 mg‧m-2‧h-1. The maximum CO net emissions occurred after the compost was turned (1.7x to 13.7x higher than before turning). The top sections of hermetised piles had greater CO emissions compared to sides. Additionally, 5% of measurement points of hermetised piles switched to 'CO sinks'. The 1-h concentration in hermetised composting hall can reach max. ~50 mg CO∙m-3 before turning, and >115 mg CO∙m-3 after, exceeding the WHO thresholds for a 1-h and 15-min exposures, respectively.

Nitrogen Removal from Landfill Leachate Using Biochar Derived from Wheat Straw.

Landfill leachate (LLCH) disposal poses challenges due to high pollutant concentrations. This study investigates the use of biochar (BC) derived from wheat straw for nitrogen content reduction. Laboratory experiments evaluated BC's adsorption capacity (qm) for nitrogen removal from ammonium chloride solution (NH4Cl) and LLCH, along with testing isotherm models. The results demonstrated that BC was more efficient (95.08%) than commercial activated carbon AC (93.11%), the blank, in adsorbing nitrogen from NH4Cl. This superior performance of BC may be attributed to its higher carbon content (57.74%) observed through elemental analysis. Lower results for BC/LLCH may be due to LLCH's complex chemical matrix. The Langmuir isotherm model best described BC/NH4Cl adsorption (qm = 0.5738 mg/g). The AC/NH4Cl data also fitted into the Langmuir (R2 ˃ 0.9) with a qm of 0.9469 mg/g, and 26.667 mg/g (R2 ˂ 0.9) was obtained for BC/LLCH; the BC/LLCH also gave higher qm (R2 ˃ 0.9) using the Jovanovich model (which also follows Langmuir's assumptions). The mean energy of the adsorption values estimated for the AC/NH4Cl, BC/NH4Cl, and BC/LLCH processes were 353.55, 353.55, and 223.61 kJ/mol, respectively, suggesting that they are all chemisorption processes and ion exchange influenced their adsorption processes. The Freundlich constant (1/n) value suggests average adsorption for BC/LLCH. The BC/LLCH data followed the Harkins-Jura model (R2: 0.9992), suggesting multilayered adsorption (or mesopore filling). In conclusion, biochar derived from wheat straw shows promising potential for landfill leachate remediation, offering efficient nitrogen removal capabilities and demonstrating compatibility with various adsorption models. This research also lays the groundwork for further exploration of other biochar-based materials in addressing environmental challenges associated with landfill leachate contamination.

Revealing the Adverse Impact of Additive Carbon Material on Microorganisms and Its Implications for Biogas Yields: A Critical Review.

Biochar could be a brilliant additive supporting the anaerobic fermentation process. However, it should be taken into account that in some cases it could also be harmful to microorganisms responsible for biogas production. The negative impact of carbon materials could be a result of an overdose of biochar, high biochar pH, increased arsenic mobility in the methane fermentation solution caused by the carbon material, and low porosity of some carbon materials for microorganisms. Moreover, when biochar is affected by an anaerobic digest solution, it could reduce the biodiversity of microorganisms. The purpose of the article is not to reject the idea of biochar additives to increase the efficiency of biogas production, but to draw attention to the properties and ways of adding these materials that could reduce biogas production. These findings have practical relevance for organizations seeking to implement such systems in industrial or local-scale biogas plants and provide valuable insights for future research. Needless to say, this study will also support the implementation of biogas technologies and waste management in implementing the idea of a circular economy, further emphasizing the significance of the research.

Study on the Effect of Hydrothermal Carbonization Parameters on Fuel Properties of Sewage Sludge Hydrochar.

In the wake of economic and population growth, increased wastewater production poses a challenge related to sewage sludge treatment, which is problematic given its high moisture content, amount, and hazardous characteristics. This study focuses on the hydrothermal carbonization of sewage sludge to produce carbonous material-hydrochar, which may be an alternative to fossil fuels. The effect of process parameters, namely, temperature (180, 240, 300 °C) and duration time (30, 90, 180 min), on hydrochar properties (proximate and ultimate analysis, heating values) and process performance were studied. Obtained results indicate and confirm that hydrothermal carbonization, especially temperature increase, improves the fuel properties of carbonized sewage sludge. The highest low heating value was obtained for hydrochar derived at 300 °C in 180 min (~23 MJ × kg-1). The highest energy gain was noted for hydrochar derived at 240 °C in 180 min (~23%). As well as relatively high mass and energy yield in comparison to other hydrochars, these parameters are considered the most favorable for sewage sludge hydrothermal carbonization. However, high energy consumption (over 1300 kJ × g-1) suggests that more research on the process's economical efficacy is required.

Direct interspecies electron transfer mechanisms of a biochar-amended anaerobic digestion: a review.

This paper explores the mechanisms of biochar that facilitate direct interspecies electron transfer (DIET) among syntrophic microorganisms leading to improved anaerobic digestion. Properties such as specific surface area (SSA), cation exchange capacity (CEC), presence of functional groups (FG), and electrical conductivity (EC) were found favorable for increased methane production, reduction of lag phase, and adsorption of inhibitors. It is revealed that these properties can be modified and are greatly affected by the synthesizing temperature, biomass types, and residence time. Additionally, suitable biochar concentration has to be observed since dosage beyond the optimal range can create inhibitions. High organic loading rate (OLR), pH shocks, quick accumulation and relatively low degradation of VFAs, and the presence of heavy metals and toxins are the major inhibitors identified. Summaries of microbial community analysis show fermentative bacteria and methanogens that are known to participate in DIET. These are Methanosaeta, Methanobacterium, Methanospirillum, and Methanosarcina for the archaeal community; whereas, Firmicutes, Proteobacteria, Synergistetes, Spirochetes, and Bacteroidetes are relatively for bacterial analyses. However, the number of defined cocultures promoting DIET is very limited, and there is still a large percentage of unknown bacteria that are believed to support DIET. Moreover, the instantaneous growth of participating microorganisms has to be validated throughout the process.

Influence of Pre-Incubation of Inoculum with Biochar on Anaerobic Digestion Performance.

The application of biochar as an additive to enhance the anaerobic digestion (AD) of biomass has been extensively studied from various perspectives. This study reported, for the first time, the influence of biochar incubation in the inoculum on the anaerobic fermentation of glucose in a batch-type reactor over 20 days. Three groups of inoculum with the same characteristics were pre-mixed once with biochar for different durations: 21 days (D21), 10 days (D10), and 0 days (D0). The BC was mixed in the inoculum at a concentration of 8.0 g/L. The proportion of the inoculum and substrate was adjusted to an inoculum-to-substrate ratio of 2.0 based on the volatile solids. The results of the experiment revealed that D21 had the highest cumulative methane yield, of 348.98 mL, compared to 322.66, 290.05, and 25.15 mL obtained from D10, D0, and the control, respectively. Three models-modified Gompertz, first-order, and Autoregressive Integrated Moving Average (ARIMA)-were used to interpret the biomethane production. All models showed promising fitting of the cumulative biomethane production, as indicated by high R2 and low RMSE values. Among these models, the ARIMA model exhibited the closest fit to the actual data. The biomethane production rate, derived from the modified Gompertz Model, increased as the incubation period increased, with D21 yielding the highest rate of 31.13 mL/gVS. This study suggests that the application of biochar in the anaerobic fermentation of glucose, particularly considering the short incubation period, holds significant potential for improving the overall performance of anaerobic digestion.

Carbon Monoxide Production during Bio-Waste Composting under Different Temperature and Aeration Regimes.

Despite the development of biorefinery processes, the possibility of coupling the "conventional" composting process with the production of biochemicals is not taken into account. However, net carbon monoxide (CO) production has been observed during bio-waste composting. So far, O2 concentration and temperature have been identified as the main variables influencing CO formation. This study aimed to investigate CO net production during bio-waste composting under controlled laboratory conditions by varying aeration rates and temperatures. A series of composting processes was carried out in conditions ranging from mesophilic to thermophilic (T = 35, 45, 55, and 65 °C) and an aeration rate of 2.7, 3.4, 4.8, and 7.8 L·h-1. Based on the findings of this study, suggestions for the improvement of CO production throughout the composting process have been developed for the first time. The highest concentrations of CO in each thermal variant was achieved with an O2 deficit (aeration rate 2.7 L·h-1); additionally, CO levels increased with temperature, reaching ~300 ppm at 65 °C. The production of CO in mesophilic and thermophilic conditions draws attention to biological CO formation by microorganisms capable of producing the CODH enzyme. Further research on CO production efficiency in these thermal ranges is necessary with the characterization of the microbial community and analysis of the ability of the identified bacteria to produce the CODH enzyme and convert CO from CO2.

Modelling and optimisation of electrocoagulation/flocculation recovery of effluent from land-based aquaculture by artificial intelligence (AI) approaches.

This study examined the modelling and optimisation of the electrocoagulation-flocculation (ECF) recovery of aquaculture effluent (AQE) using aluminium electrodes. The response surface methodology (RSM), artificial neural network (ANN), and adaptive neuro-fuzzy inference system (ANFIS) were used for the modelling, while the optimisation tools were the numerical RSM and genetic algorithm (GA). Furthermore, the kinetics of the ECF process was studied to provide insight into the mechanism governing the ECF of AQE. The experimental design was performed using the central composite design (CCD) of the RSM. The ANFIS modelling was accomplished via the Grid Partition (GP) of the data set, while the ANN used the multi-layer perceptron (MLP) based feed-forward system. Statistically, the prediction accuracy of the models followed the order: ANFIS (R2: 0.9990), ANN (R2: 0.9807), and RSM (R2: 0.9790). The process optimisation gave optimal turbidity (TD) removal efficiencies of 98.98, 97.81, and 96.01% for ANFIS-GA, ANN-GA, and RSM optimisation techniques, respectively. The ANFIS-GA gave the best optimization result at optimum conditions of pH 4, current intensity (3 A), electrolysis time (7.2 min), settling time (23 min), and temperature (43.8 °C). In the kinetics study, the experimental data was analysed using pseudo-first-order (0.8787), pseudo-second-order (0.9395), and Elovich (R2: 0.9979) kinetic models; the Elovich model gave the best correlation with the experimental data showing that the process is governed by electrostatic interaction mechanism. This study effectively demonstrated that ECF recovery of AQE can effectively be modelled using RSM, ANN, and ANFIS and be optimised using RSM, ANN-GA, and ANFIS-GA techniques, and the order of performance is ANFIS > ANN > RSM and ANFIS-GA > ANN-GA > RSM, respectively.

A review of the adsorption method for norfloxacin reduction from aqueous media.

Norfloxacin (NRFX) is one of a class of antibiotics known as broad-spectrum fluoroquinolone antibiotic that is frequently used to treat infectious disorders in both animals and humans. NRFX is considered an emergent pharmaceutical contaminate. This review's objective is to evaluate empirical data on NRFX's removal from aqueous medium. The environmental danger of NRFX in the aquatic environment was validated by an initial ecotoxicological study. Graphene oxide/Metal Organic Framework (MOF) based composite, followed by Magnesium oxide/Chitosan/Graphene oxide composite gave the highest NRFX adsorption capacities (Qmax) of 1114.8 and 1000 mg/g, respectively. The main adsorption mechanisms for NRFX uptake include electrostatic interactions, H-bonds, π-π interactions, electron donor-acceptor interactions, hydrophobic interactions, and pore diffusion. The adsorptive uptake of NRFX were most suitably described by Langmuir isotherm and pseudo-second order implying adsorbate-to-adsorbent electron transfer on a monolayer surface. The thermodynamics of NRFX uptake is heavily dependent on the makeup of the adsorbent, and the selection of the eluent for desorption from the solid phase is equally important. There were detected knowledge gaps in column studies and adsorbent disposal method. There's great interest in scale-up and industrial applications of research results that will aid in management of water resources for sustainability.

Biological treatment of biowaste as an innovative source of CO-The role of composting process.

Carbon monoxide (CO) is an essential "building block" for producing everyday chemicals on industrial scale. Carbon monoxide can also be generated though a lesser-known and sometimes forgotten biorenewable pathways that could be explored to advance biobased production from large and more sustainable sources such as bio-waste treatment. Organic matter decomposition can generate carbon monoxide both under aerobic and anaerobic conditions. While anaerobic carbon monoxide generation is relatively well understood, the aerobic is not. Yet many industrial-scale bioprocesses involve both conditions. This review summarizes the necessary basic biochemistry knowledge needed for realization of initial steps towards biobased carbon monoxide production. We analyzed for the first time, the complex information about carbon monoxide production during aerobic, anaerobic bio-waste treatment and storage, carbon monoxide-metabolizing microorganisms, pathways, and enzymes with bibliometric analysis of trends. The future directions recognizing limitations of combined composting and carbon monoxide production have been discussed in greater detail.

Investigation of the performance of a cylindrical hopper and metering device of a carrot seeder.

A carrot seeder that utilizes a cylindrical component serving as both hopper/metering device to deposit seeds precisely into planting beds/hills at a uniform interval along a straight row over a plant bed was developed in this study. The seeder was evaluated at different operating speeds (89, 70, 61, 51, 48, 38, and 34 cm s-1) relative to mean number of seeds planted in each hill, hill center, scattering distance ratio, hill spacing and missed hills. The seeder was able to deposit seeds in each hill ranging from 2.8 to 4.0 at all speeds. The mean hill center and missed hills suggested that the seeder is best operated at speed under 70 cm s-1 with the respective values ranging from 0.9 to 1.6 cm and 0-5.5%. This indicates that number of the seeds dropped per hill was very uniform, which is a good indicator of the seeding performance. The hill center and missed hills at 89 cm s-1 were 3.08 cm and 16.67% respectively were significantly higher than at lower speeds. Other operating performances such as the mean number of seeds deposited in each hill and the distance between hills did not appear to vary with the planting speed. The scattering distance ratios of operating speeds from 34 to 61 cm s-1 were less than 30% and therefore acceptable for hill dropping of carrot seeds.

Purification of aquaculture effluent using Picralima nitida seeds.

Aquaculture effluent treatment is essential to eliminate the undesirable characteristics of water to ensure cleaner production and environmental sustainability. In an effort to develop green coagulant without compromising cost, this research investigated the feasibility of aquaculture effluent (AQEF) pollutant removal using Picralima nitida seeds extract (PNSC) and its bio-coagulation/adsorption kinetic characteristics with the substrate in water. The coagulative decrease was observed in terms of TD (turbidity), TSS (total suspended solids), COD (chemical oxygen demand), BOD (biochemical oxygen demand), and COLR (color) from AQEF. The active coagulant was extracted from the seeds and analyzed for its spectral and morphological characteristics through FTIR and SEM. The influence of PNSC dosage (0.10-0.50 g L-1), pH (2-10), settling time (0-60 min), and temperature (303-323 K) on the removal of contaminants were surveyed. The process kinetics of coagulation-flocculation were also explored. Maximal TD reduction of 90.35%, COD (82.11%), BOD (82.38%); TSS (88.84%), and COLR (65.77%) at 0.2 g PNSC L-1, pH 4, and 303 K was achieved. Analysis of variance (ANOVA) tests proved that pH, temperature, and settling time had a significant effect on pollutant removal. Results fitted Von Smoluchowski's perikinetics theory at the optimum conditions, which gave R2 > 0.900. At perikinetics circumstances, the Kb (reaction rate) and [Formula: see text] (half-life) correspond to 0.0635 Lg-1 min-1 and 1.9 min. More so, sorption results fitted the Lagergren over the Ho model. Additionally, the net cost of using PNSC to handle 1 L of AQEF (including electricity, material, and labor costs) was evaluated to be €4.81. Overall, the PNSC appears reliable and useful in pretreating AQEF for improved biodegradability and superior effluent quality.