Correlation between Graphitic Carbon and Elemental Carbon in Diesel Particulate Matter in Workplace Atmospheres.

We investigated the suitability of the graphitic carbon (GC) content of diesel particulate matter (DPM), measured using Raman spectroscopy, as a surrogate measure of elemental carbon (EC) determined by thermal optical analysis. The Raman spectra in the range of 800-1800 cm-1 (including the D mode at ∼1322 cm-1 and the G mode at ∼1595 cm-1) were used for GC identification and quantification. Comparison of the Raman spectra for two certified DPM standards (NIST SRM 1650 and SRM 2975), two types of diesel engine exhaust soot, and three types of DPM-enriched workplace aerosols show that the uncertainty of GC quantification based on the D peak height, G peak height, and the total peak area below D and G peaks was about 6.0, 6.7, and 6.9%, respectively. The low uncertainty for different aerosol types suggested possible use of GC as a surrogate measure of EC in workplace atmospheres. A calibration curve was constructed using two laboratory-aerosolized DPM standards to describe the relationship between GC measured by a portable Raman spectrometer and the EC concentration determined by NIOSH Method 5040. The calibration curve was then applied to determine GC-based estimates of the EC contents of diesel engine exhaust samples from two vehicles and seven air samples collected at a hydraulic fracturing worksite. The GC-EC estimates obtained through Raman measurements agreed well with those found by NIOSH Method 5040 for the same samples at EC filter loadings below 2.86 µg/cm2. The study shows that using an appropriate sample collection method that avoids high filter mass loadings, onsite measurement of GC by a portable or hand-held Raman spectrometer can provide a useful indicator of EC in workplace aerosol.

Toggle-like current-induced Bloch point dynamics of 3D skyrmion strings in a room temperature nanowire.

Research into practical applications of magnetic skyrmions, nanoscale solitons with interesting topological and transport properties, has traditionally focused on two dimensional (2D) thin-film systems. However, the recent observation of novel three dimensional (3D) skyrmion-like structures, such as hopfions, skyrmion strings (SkS), skyrmion bundles, and skyrmion braids, motivates the investigation of new designs, aiming to exploit the third spatial dimension for more compact and higher performance spintronic devices in 3D or curvilinear geometries. A crucial requirement of such device schemes is the control of the 3D magnetic structures via charge or spin currents, which has yet to be experimentally observed. In this work, we utilise real-space imaging to investigate the dynamics of a 3D SkS within a nanowire of Co8Zn9Mn3 at room temperature. Utilising single current pulses, we demonstrate current-induced nucleation of a single SkS, and a toggle-like positional switching of an individual Bloch point at the end of a SkS. The observations highlight the possibility to locally manipulate 3D topological spin textures, opening up a range of design concepts for future 3D spintronic devices.

History-dependent domain and skyrmion formation in 2D van der Waals magnet Fe3GeTe2.

The discovery of two-dimensional magnets has initiated a new field of research, exploring both fundamental low-dimensional magnetism, and prospective spintronic applications. Recently, observations of magnetic skyrmions in the 2D ferromagnet Fe3GeTe2 (FGT) have been reported, introducing further application possibilities. However, controlling the exhibited magnetic state requires systematic knowledge of the history-dependence of the spin textures, which remains largely unexplored in 2D magnets. In this work, we utilise real-space imaging, and complementary simulations, to determine and explain the thickness-dependent magnetic phase diagrams of an exfoliated FGT flake, revealing a complex, history-dependent emergence of the uniformly magnetised, stripe domain and skyrmion states. The results show that the interplay of the dominant dipolar interaction and strongly temperature dependent out-of-plane anisotropy energy terms enables the selective stabilisation of all three states at zero field, and at a single temperature, while the Dzyaloshinksii-Moriya interaction must be present to realise the observed Néel-type domain walls. The findings open perspectives for 2D devices incorporating topological spin textures.

In Vivo Efficacy of Olorofim against Systemic Scedosporiosis and Lomentosporiosis.

Clinically relevant members of the Scedosporium/Pseudallescheria species complex and Lomentospora prolificans are generally resistant against currently available systemic antifungal agents in vitro, and infection due to these species is difficult to treat. We studied the in vivo efficacy of a new fungicidal agent, olorofim (formerly F901318), against scedosporiosis and lomentosporiosis in neutropenic animals. Cyclophosphamide-immunosuppressed CD-1 mice infected by Scedosporium apiospermum, Pseudallescheria boydii (Scedosporium boydii), and Lomentospora prolificans were treated by intraperitoneal administration of olorofim (15 mg/kg of body weight every 8 h for 9 days). The efficacy of olorofim treatment was assessed by the survival rate at 10 days postinfection, levels of serum (1-3)-ß-d-glucan (BG), histopathology, and fungal burdens of kidneys 3 days postinfection. Olorofim therapy significantly improved survival compared to that of the untreated controls; 80%, 100%, and 100% of treated mice survived infection by Scedosporium apiospermum, Pseudallescheria boydii, and Lomentospora prolificans, respectively, while less than 20% of the control mice (phosphate-buffered saline [PBS] treated) survived at 10 days postinfection. In the olorofim-treated neutropenic CD-1 mice infected with any of the three species, serum BG levels were significantly suppressed and fungal DNA detected in the target organs was significantly lower than in controls. Furthermore, histopathology of kidneys revealed no or only a few lesions with hyphal elements in the olorofim-treated mice, while numerous fungal hyphae were present in control mice. These results indicate olorofim to be a promising therapeutic agent for systemic scedosporiosis/lomentosporiosis, devastating emerging fungal infections that are difficult to treat with currently available antifungals.

Physicochemical characterization and genotoxicity of the broad class of carbon nanotubes and nanofibers used or produced in U.S. facilities.

BACKGROUND: Carbon nanotubes and nanofibers (CNT/F) have known toxicity but simultaneous comparative studies of the broad material class, especially those with a larger diameter, with computational analyses linking toxicity to their fundamental material characteristics was lacking. It was unclear if all CNT/F confer similar toxicity, in particular, genotoxicity. Nine CNT/F (MW #1-7 and CNF #1-2), commonly found in exposure assessment studies of U.S. facilities, were evaluated with reported diameters ranging from 6 to 150 nm. All materials were extensively characterized to include distributions of physical dimensions and prevalence of bundled agglomerates. Human bronchial epithelial cells were exposed to the nine CNT/F (0-24 µg/ml) to determine cell viability, inflammation, cellular oxidative stress, micronuclei formation, and DNA double-strand breakage. Computational modeling was used to understand various permutations of physicochemical characteristics and toxicity outcomes. RESULTS: Analyses of the CNT/F physicochemical characteristics illustrate that using detailed distributions of physical dimensions provided a more consistent grouping of CNT/F compared to using particle dimension means alone. In fact, analysis of binning of nominal tube physical dimensions alone produced a similar grouping as all characterization parameters together. All materials induced epithelial cell toxicity and micronuclei formation within the dose range tested. Cellular oxidative stress, DNA double strand breaks, and micronuclei formation consistently clustered together and with larger physical CNT/F dimensions and agglomerate characteristics but were distinct from inflammatory protein changes. Larger nominal tube diameters, greater lengths, and bundled agglomerate characteristics were associated with greater severity of effect. The portion of tubes with greater nominal length and larger diameters within a sample was not the majority in number, meaning a smaller percentage of tubes with these characteristics was sufficient to increase toxicity. Many of the traditional physicochemical characteristics including surface area, density, impurities, and dustiness did not cluster with the toxicity outcomes. CONCLUSION: Distributions of physical dimensions provided more consistent grouping of CNT/F with respect to toxicity outcomes compared to means only. All CNT/F induced some level of genotoxicity in human epithelial cells. The severity of toxicity was dependent on the sample containing a proportion of tubes with greater nominal lengths and diameters.

Real-space imaging of confined magnetic skyrmion tubes.

Magnetic skyrmions are topologically nontrivial particles with a potential application as information elements in future spintronic device architectures. While they are commonly portrayed as two dimensional objects, in reality magnetic skyrmions are thought to exist as elongated, tube-like objects extending through the thickness of the host material. The study of this skyrmion tube state (SkT) is vital for furthering the understanding of skyrmion formation and dynamics for future applications. However, direct experimental imaging of skyrmion tubes has yet to be reported. Here, we demonstrate the real-space observation of skyrmion tubes in a lamella of FeGe using resonant magnetic x-ray imaging and comparative micromagnetic simulations, confirming their extended structure. The formation of these structures at the edge of the sample highlights the importance of confinement and edge effects in the stabilisation of the SkT state, opening the door to further investigation into this unexplored dimension of the skyrmion spin texture.

Systematic scoping review of mandibular bone tissue engineering.

Tissue engineering is a promising alternative that may facilitate bony regeneration in small defects in compromised host tissue as well as large mandibular defects. This scoping systematic review was therefore designed to assess in vivo research on its use in the reconstruction of mandibular defects in animal models. A total of 4524 articles were initially retrieved using the search algorithm. After screening of the titles and abstracts, 269 full texts were retrieved, and a total of 72 studies included. Just two of the included studies employed osteonecrosis as the model of mandibular injury. All the rest involved the creation of a critical defect. Calcium phosphates, especially tricalcium phosphate and hydroxyapatite, were the scaffolds most widely used. All the studies that used a scaffold reported increased formation of bone when compared with negative controls. When combined with scaffolds, mesenchymal stem cells (MSC) increased the formation of new bone and improved healing. Various growth factors have been studied for their potential use in the regeneration of the maxillofacial complex. Bone morphogenic proteins (BMP) were the most popular, and all subtypes promoted significant formation of bone compared with controls. Whilst the studies published to date suggest a promising future, our review has shown that several shortfalls must be addressed before the findings can be translated into clinical practice. A greater understanding of the underlying cellular and molecular mechanisms is required to identify the optimal combination of components that are needed for predictable and feasible reconstruction or regeneration of mandibular bone. In particular, a greater understanding of the biological aspects of the regenerative triad is needed before we can to work towards widespread translation into clinical practice.

Quasi-periodic ripples in high latitude electron content, the geomagnetic field, and the solar wind.

In this study we present evidence for the existence of quasi-periodic ripples in the F-region electron content at high latitude, the magnetic flux density at geosynchronous orbit, and the solar wind dynamic pressure and IMF flux density at L1. The ripples are shown to be continually present during all 14 days of observations in different years and seasons, and at all local times, though they are generally small in magnitude relative to the background. The frequencies of all the parameters are, on average, remarkably similar, and the amplitudes of the selected peaks of some parameters show strong correlations for which regression formulae are given. These results support the proposition that the ripples propagate from the solar wind to the F-region, and that they are a related, persistent phenomenon.

Local magnetism, magnetic order and spin freezing in the 'nonmetallic metal' FeCrAs.

We present the results of x-ray scattering and muon-spin relaxation ([Formula: see text]SR) measurements on the iron-pnictide compound FeCrAs. Polarized non-resonant magnetic x-ray scattering results reveal the 120° periodicity expected from the suggested three-fold symmetric, non-collinear antiferromagnetic structure. [Formula: see text]SR measurements indicate a magnetically ordered phase throughout the bulk of the material below [Formula: see text] K. There are signs of fluctuating magnetism in a narrow range of temperatures above [Formula: see text] involving low-energy excitations, while at temperatures well below [Formula: see text] behaviour characteristic of freezing of dynamics is observed, likely reflecting the effect of disorder in our polycrystalline sample. Using density functional theory we propose a distinct muon stopping site in this compound and assess the degree of distortion induced by the implanted muon.

Highly Sensitive Lab on a Chip (LOC) Immunoassay for Early Diagnosis of Respiratory Disease Caused by Respirable Crystalline Silica (RCS).

Respirable crystalline silica (RCS) produced in mining and construction industries can cause life-threatening diseases such as silicosis, lung cancer, and chronic obstructive pulmonary disease (COPD). These diseases could be more effectively treated and prevented if RCS-related biomarkers were identified and measured at an early stage of disease progression, which makes development of a point of care test (POCT) platform extremely desirable for early diagnosis. In this work, a new, highly sensitive lab on a chip (LOC) immunoassay has been designed, developed, and characterized for tumor necrosis factor α (TNF-α), a protein biomarker that causes lung inflammation due to RCS exposure. The designed LOC device is composed of four reservoirs for sample, enzyme conjugated detection antibody, wash buffer, and chemiluminescence substrate in liquid form, along with three spiral reaction chambers for test, positive control, and negative control. All reservoirs and spiral microchannels were connected in series and designed to perform sequential delivery of immunoassay reagents with minimal user intervention. The developed LOC measured TNF-α concentrations as low as 16 pg/mL in plasma from RCS-exposed rats and also had a limit of detection (LOD) of 0.5 pg/mL in spiked artificial serum. In addition, the analysis time was drastically reduced to about 30 min, as opposed to hours in conventional methods. Successful implementation of a highly sensitive, chemiluminescence-based immunoassay on a preloaded LOC with proper quality control, as reported in this work, can pave the way toward developing a new rapid POCT platform for in-field clinical diagnosis.

Efficacy of Olorofim (F901318) against Aspergillus fumigatus, A. nidulans, and A. tanneri in Murine Models of Profound Neutropenia and Chronic Granulomatous Disease.

The emergence of azole resistance in Aspergillus fumigatus as well as an increasing frequency of multiresistant cryptic Aspergillus spp. necessitates exploration of new classes of antifungals. Olorofim (formerly F901318) is a new fungicidal agent that prevents the growth of ascomycetous mold species via inhibition of de novo pyrimidine biosynthesis, a mechanism of action distinct from that of currently available antifungal drugs. We studied the in vivo efficacy of olorofim intraperitoneal therapy (15 mg/kg of body weight every 8 h for 9 days) against infection with A. fumigatus, A. nidulans, and A. tanneri in both neutropenic CD-1 mice and mice with chronic granulomatous disease (CGD) (gp91-/-phox mice). In the neutropenic mouse model, 80% to 88% of treated mice survived for 10 days, and in the CGD group, 63% to 88% of treated mice survived for 10 days, depending on the infecting species, while less than 10% of the mice in the control groups survived for 10 days. In the olorofim-treated groups, galactomannan levels were significantly suppressed, with lower organ fungal DNA burdens being seen for all three Aspergillus spp. Histopathological slides revealed a limited number of inflammatory foci with or without detectable fungal elements in the kidneys of neutropenic CD-1 mice and in the lungs of CGD mice. Furthermore, the efficacy of olorofim was unrelated to the triazole MICs of the infecting Aspergillus spp. These results show olorofim to be a promising therapeutic agent for invasive aspergillosis.

Technical report: Inter- and intra-rater reliability of regional gastrointestinal transit times measured using the 3D-Transit electromagnet tracking system.

BACKGROUND: The 3D-Transit electromagnet tracking system is an emerging tool for the ambulatory assessment of gastrointestinal (GI) transit times and motility patterns, based on the anatomical localization of ingestible electromagnetic capsules. Currently, 3D-Transit recordings are manually analyzed to extract GI transit times. As this is a subjective method, there is some inherent variability in the measurements, which may be experience-dependent. We therefore assessed inter- and intra-rater reliability of GI transit times from 3D-Transit recordings. METHODS: Thirty-six 3D-Transit recordings (17 female; median age: 34 years [range: 21-80]) were analyzed twice by 3 raters with varying experience. Each rater manually identified the timestamps when a capsule progressed from antrum to duodenum, and from ileum to right colon. These timestamps, along with the ingestion and expulsion times, were used to determine whole gut (WGTT), gastric emptying (GET), small intestinal (SITT) and colonic (CTT) transit times. Reliability was determined using interclass correlation coefficients (ICCs). KEY RESULTS: For capsule progression timestamps, the most and mid-experienced raters had fair to good inter- and excellent intra-rater reliability (ICCmin-max  = 0.61-1.00), whereas the inexperienced rater had poor to fair inter- and poor intra-rater reliability (ICCmin-max  = 0.28-0.55). GET and SITT reliability between the most and mid-experienced raters was fair (ICCmin-max  = 0.61-0.73), while reliability between these raters and the inexperienced rater was poor to fair (ICCmin-max  = 0.28-0.55). CTT reliability was excellent between and within all raters (ICCmin-max  = 0.92-0.99). CONCLUSIONS & INFERENCES: Inexperienced raters provide the least reliable measurements from 3D-Transit recordings, which confirms requirement for adequate training. Automation may improve the reliability of measurements.

Association of pulmonary, cardiovascular, and hematologic metrics with carbon nanotube and nanofiber exposure among U.S. workers: a cross-sectional study.

BACKGROUND: Commercial use of carbon nanotubes and nanofibers (CNT/F) in composites and electronics is increasing; however, little is known about health effects among workers. We conducted a cross-sectional study among 108 workers at 12 U.S. CNT/F facilities. We evaluated chest symptoms or respiratory allergies since starting work with CNT/F, lung function, resting blood pressure (BP), resting heart rate (RHR), and complete blood count (CBC) components. METHODS: We conducted multi-day, full-shift sampling to measure background-corrected elemental carbon (EC) and CNT/F structure count concentrations, and collected induced sputum to measure CNT/F in the respiratory tract. We measured (nonspecific) fine and ultrafine particulate matter mass and count concentrations. Concurrently, we conducted physical examinations, BP measurement, and spirometry, and collected whole blood. We evaluated associations between exposures and health measures, adjusting for confounders related to lifestyle and other occupational exposures. RESULTS: CNT/F air concentrations were generally low, while 18% of participants had evidence of CNT/F in sputum. Respiratory allergy development was positively associated with inhalable EC (p=0.040) and number of years worked with CNT/F (p=0.008). No exposures were associated with spirometry-based metrics or pulmonary symptoms, nor were CNT/F-specific metrics related to BP or most CBC components. Systolic BP was positively associated with fine particulate matter (p-values: 0.015-0.054). RHR was positively associated with EC, at both the respirable (p=0.0074) and inhalable (p=0.0026) size fractions. Hematocrit was positively associated with the log of CNT/F structure counts (p=0.043). CONCLUSIONS: Most health measures were not associated with CNT/F. The positive associations between CNT/F exposure and respiratory allergies, RHR, and hematocrit counts may not be causal and require examination in other studies.

Quantification of Carbon Nanotubes by Raman Analysis.

The increasing prevalence of carbon nanotubes (CNTs) in manufacturing and research environments, together with the potential exposure risks, necessitates development of reliable and accurate monitoring methods for these materials. We examined quantification of CNTs by two distinct methods based on Raman spectroscopy. First, as measured by the Raman peak intensity of aqueous CNT suspensions, and second, by Raman mapping of air filter surfaces onto which CNTs were collected as aerosols or applied as small-area (0.05 cm2) deposits. Correlation (R2 = 0.97) between CNT concentration and Raman scattering intensity for suspensions in cuvettes was found over a concentration range from about 2 to 10 µg/ml, but measurement variance precludes practical determination of a calibration curve. Raman mapping of aerosol sample filter surfaces shows correlation with CNT mass when the surface density is relatively high (R2 = 0.83 and 0.95 above about 5 µg total mass on filter), while heterogeneity of CNT deposition makes obtaining representative maps of lower density samples difficult. This difficulty can be mitigated by increasing the area mapped relative to the total sample area, improving both precision and the limit of detection (LOD). For small-area deposits, detection of low masses relevant to occupational monitoring can be achieved, with an estimated LOD of about 50 ng.

Carbon nanotube and nanofiber exposure and sputum and blood biomarkers of early effect among U.S. workers.

BACKGROUND: Carbon nanotubes and nanofibers (CNT/F) are increasingly used for diverse applications. Although animal studies suggest CNT/F exposure may cause deleterious health effects, human epidemiological studies have typically been small, confined to single workplaces, and limited in exposure assessment. OBJECTIVES: We conducted an industrywide cross-sectional epidemiological study of 108 workers from 12 U.S. sites to evaluate associations between occupational CNT/F exposure and sputum and blood biomarkers of early effect. METHODS: We assessed CNT/F exposure via personal breathing zone, filter-based air sampling to measure background-corrected elemental carbon (EC) (a CNT/F marker) mass and microscopy-based CNT/F structure count concentrations. We measured 36 sputum and 37 blood biomarkers. We used factor analyses with varimax rotation to derive factors among sputum and blood biomarkers separately. We used linear, Tobit, and unconditional logistic regression models to adjust for potential confounders and evaluate associations between CNT/F exposure and individual biomarkers and derived factors. RESULTS: We derived three sputum and nine blood biomarker factors that explained 78% and 67%, respectively, of the variation. After adjusting for potential confounders, inhalable EC and total inhalable CNT/F structures were associated with the most sputum and blood biomarkers, respectively. Biomarkers associated with at least three CNT/F metrics were 72 kDa type IV collagenase/matrix metalloproteinase-2 (MMP-2), interleukin-18, glutathione peroxidase (GPx), myeloperoxidase, and superoxide dismutase (SOD) in sputum and MMP-2, matrix metalloproteinase-9, metalloproteinase inhibitor 1/tissue inhibitor of metalloproteinases 1, 8-hydroxy-2'-deoxyguanosine, GPx, SOD, endothelin-1, fibrinogen, intercellular adhesion molecule 1, vascular cell adhesion protein 1, and von Willebrand factor in blood, although directions of associations were not always as expected. CONCLUSIONS: Inhalable rather than respirable CNT/F was more consistently associated with fibrosis, inflammation, oxidative stress, and cardiovascular biomarkers.

Analysis of Crystalline Silica Aerosol Using Portable Raman Spectrometry: Feasibility of Near Real-Time Measurement.

A Raman spectroscopy based method has been developed for measurement of trace airborne concentrations of respirable crystalline silica (RCS) using various aerosol sampling and analysis techniques. Three aerosol microconcentration techniques were investigated for effective coupling of collected particulate samples with micro-Raman spectroscopy: (i) direct analysis on a particulate filter after focused aerosol collection using a converging nozzle; (ii) analysis of dried particulate deposit on a filter obtained directly from the aerosol phase using the Spotsampler device; and (iii) analysis of a dried spot (∼1-3 mm diameter) obtained by redepositing the particulate sample, after low-temperature plasma ashing of the filter sample. The deposition characteristics (i.e., spot diameter, shape, and deposit uniformity) of each technique were investigated. Calibration curves were constructed and detection limits were estimated for α-quartz using the A1 Raman Si-O-Si stretching-bending phonon mode at 465 cm-1. The measurement sensitivity could be substantially improved by increasing the signal integration time and by reducing the particle deposition area. Detection limits in the range of 8-55 ng could be achieved by microconcentrating the aerosol sample over a spot measuring 400-1000 µm in diameter. These detection limits were two to three orders of magnitude lower compared to those attainable using current standardized X-ray diffraction and infrared spectroscopy methods. The low detection limits suggest that near real-time measurements of RCS could be achieved with limits of quantification ranging from 2 to 18.5 µg/m3 (at 10 min collection time and 1.2 L/min sampling flow rate), depending on microconcentration technique used. The method was successfully extended to the measurement of α-quartz air concentration in representative workplace aerosol samples. This study demonstrates the potential of portable micro-Raman spectroscopy for near-real time measurement of trace RCS in air.

Exposure assessments for a cross-sectional epidemiologic study of US carbon nanotube and nanofiber workers.

BACKGROUND: Recent animal studies have suggested the potential for wide-ranging health effects resulting from exposure to carbon nanotubes and nanofibers (CNT/F). To date, no studies in the US have directly examined the relationship between occupational exposure and potential human health effects. OBJECTIVES: Our goal was to measure CNT/F exposures among US workers with representative job types, from non-exposed to highly exposed, for an epidemiologic study relating exposure to early biologic effects. METHODS: 108 participants were enrolled from 12 facilities across the US. Personal, full-shift exposures were assessed based on the mass of elemental carbon (EC) at the respirable and inhalable aerosol particle size fractions, along with quantitatively characterizing CNT/F and estimating particle size via transmission electron microscopy (TEM). Additionally, sputum and dermal samples were collected and analyzed to determine internal exposures and exposures to the hands/wrists. RESULTS: The mean exposure to EC was 1.00 µg/m3 at the respirable size fraction and 6.22 µg/m3 at the inhalable fraction. Analysis by TEM found a mean exposure of 0.1275 CNT/F structures/cm3, generally to agglomerated materials between 2 and 10 µm. Internal exposures to CNT/F via sputum analysis were confirmed in 18% of participants while ∼70% had positive dermal exposures. CONCLUSIONS: We demonstrated the occurrence of a broad range of exposures to CNT/F within 12 facilities across the US. Analysis of collected sputum indicated internal exposures are currently occurring within the workplace. This is an important first step in determining if exposures in the workforce have any acute or lasting health effects.

In Vivo Toxicity Assessment of Occupational Components of the Carbon Nanotube Life Cycle To Provide Context to Potential Health Effects.

Pulmonary toxicity studies on carbon nanotubes focus primarily on as-produced materials and rarely are guided by a life cycle perspective or integration with exposure assessment. Understanding toxicity beyond the as-produced, or pure native material, is critical, due to modifications needed to overcome barriers to commercialization of applications. In the first series of studies, the toxicity of as-produced carbon nanotubes and their polymer-coated counterparts was evaluated in reference to exposure assessment, material characterization, and stability of the polymer coating in biological fluids. The second series of studies examined the toxicity of aerosols generated from sanding polymer-coated carbon-nanotube-embedded or neat composites. Postproduction modification by polymer coating did not enhance pulmonary injury, inflammation, and pathology or in vitro genotoxicity of as-produced carbon nanotubes, and for a particular coating, toxicity was significantly attenuated. The aerosols generated from sanding composites embedded with polymer-coated carbon nanotubes contained no evidence of free nanotubes. The percent weight incorporation of polymer-coated carbon nanotubes, 0.15% or 3% by mass, and composite matrix utilized altered the particle size distribution and, in certain circumstances, influenced acute in vivo toxicity. Our study provides perspective that, while the number of workers and consumers increases along the life cycle, toxicity and/or potential for exposure to the as-produced material may greatly diminish.

Characterization of an Aerosol Microconcentrator for Analysis Using Microscale Optical Spectroscopies.

Efficient microconcentration of aerosols to a substrate is essential for effectively coupling the collected particles to microscale optical spectroscopies such as laser-induced or spark microplasma, or micro-Raman or infrared spectroscopies. In this study, we present detailed characterization of a corona-based aerosol microconcentration technique developed previously (Diwakar and Kulkarni, 2012). The method involves two coaxial electrodes separated by a few millimeters, one held at a high electrical potential and the other grounded. The particles are collected on the collection (i.e., ground) electrode from a coaxial aerosol flow in a one-step charge-and-collect scheme using corona discharge and electrical precipitation between the two electrodes. Performance of the corona microconcentration method was determined experimentally by measuring collection efficiency, wall losses, and particle deposition density. An intrinsic spectroscopic sensitivity was experimentally determined for the aerosol microconcentrator. Using this sensitivity, we show that corona-based microconcentration is much superior to alternative methods, including filtration, focused impaction using aerodynamic lens, and spot collection using condensational growth. The method offers unique advantages for compact, hand-held aerosol analytical instrumentation.

In vitro activity of the novel antifungal compound F901318 against difficult-to-treat Aspergillus isolates.

Background: F901318 is a new antifungal agent with a novel mechanism of action with activity against Aspergillus species. We investigated the in vitro activity of F901318 against a collection of Aspergillus isolates. Methods: A total of 213 Aspergillus isolates were used in this study. A total of 143 Aspergillus fumigatus sensu stricto isolates were used, of which 133 were azole resistant [25 TR34/L98H; 25 TR46/Y121F/T289A; 33 A. fumigatus with cyp51A-associated point mutations (25 G54, 1 G432 and 7 M220); and 50 azole-resistant A. fumigatus without known resistance mechanisms]. Ten azole-susceptible A. fumigatus isolates were used as WT controls. The in vitro activity was also determined against Aspergillus calidoustus (25 isolates), Aspergillus flavus (10), Aspergillus nidulans (10) and Aspergillus tubingensis (25). F901318 activity was compared with that of itraconazole, voriconazole, posaconazole, isavuconazole, amphotericin B and anidulafungin. Minimum effective concentrations and MICs were determined using the EUCAST broth microdilution method. Results: F901318 was active against all tested isolates: A. fumigatus WT, MIC90 0.125 mg/L (range 0.031-0.125); TR34/L98H,TR46/Y121F/T289A and azole resistant without known resistance mechanisms, MIC90 0.125 mg/L (range 0.031-0.25); A. fumigatus with cyp51A-associated point mutations, MIC90 0.062 mg/L (range 0.015-0.125); and other species, A. calidoustus MIC90 0.5 mg/L (range 0.125-0.5), A. flavus MIC90 0.062 mg/L (range 0.015-0.62), A. nidulans MIC90 0.125 mg/L (range 0.062-0.25) and A. tubingensis MIC90 0.062 mg/L (range 0.015-0.25). Conclusions: F901318 showed potent and consistent in vitro activity against difficult-to-treat Aspergillus spp. with intrinsic and acquired antifungal resistance due to known and unknown resistance mechanisms, suggesting no significant implications of azole resistance mechanisms for the mode of action of F901318.