Guidance of ultraviolet light down to 190 nm in a hollow-core optical fibre.

We report an anti-resonant hollow core fibre with ultraviolet transmission down to 190 nm, covering the entire UV-A, UV-B and much of the UV-C band. Guidance from 190 - 400 nm is achieved apart for a narrow high loss resonance band at 245 - 265 nm. The minimum attenuation is 0.13 dB/m at 235 nm and 0.16 dB/m at 325 nm. With an inscribed core diameter of ∼12 µm, the fibre's bend loss at 325 nm was 0.22 dB per turn for a bend radius of 3 cm at 325 nm.

Axi-Stack: a method for manufacturing freeform air-silica optical fibre.

We present a method with potential for fabricating freeform air-silica optical fibre preforms which is free from the stacking constraints associated with conventional stack-and-draw. The method, termed Axi-Stack, is enabled by the precision machining of short cross-sectional preform discs by ultrafast laser assisted etching; a laser-based microfabrication technique which facilitates near arbitrary shaping of the preform structure. Several preform discs are stacked axially and fused together via ultrafast laser welding to construct the preform, which can be drawn to fibre using conventional methods. To illustrate the Axi-Stack process, we detail the fabrication of a 30 cm long solid-core photonic crystal fibre preform with a square lattice of cladding holes and characterise fibre drawn from it.

Measurement of resonant bend loss in anti-resonant hollow core optical fiber: erratum.

An error on the part of the authors in drafting resulted in Eq. (3) being incorrect in the published paper [Opt. Express25, 20612 (2017)10.1364/OE.25.020612]. We present a corrected version of the equation. It should be noted that this does not affect the presented results or conclusions of the paper.

Stack, seal, evacuate, draw: a method for drawing hollow-core fiber stacks under positive and negative pressure.

The two-stage stack and draw technique is an established method for fabricating microstructured fibers, including hollow-core fibers. A stack of glass elements of around a meter in length and centimeters in outer diameter forms the first stage preform, which is drawn into millimeter scale canes. The second stage preform is one of the canes, which is drawn, under active pressure, into microscopic fiber. Separately controlled pressure lines are connected to different holes or sets of holes in the cane to control the microstructure of the fiber being drawn, often relying on glues or other sealants to isolate the differently-pressured regions. We show that the selective fusion and collapse of the elements of the stack, before it is drawn to cane or fiber, allows the stack to be drawn directly under differential pressure without introducing a sealant. Three applications illustrate the advantages of this approach. First, we draw antiresonant hollow-core fiber directly from the stack without making a cane, allowing a significantly longer length of fiber to be drawn. Second, we fabricate canes under pressure, such that they are structurally more similar to the final fiber. Finally, we use the method to fabricate new types of microstructured resonators with a non-circular cross-section.

3D-M3: high-spatial-resolution spectroscopy with extreme AO and 3D-printed micro-lenslets.

By combining integral field spectroscopy with extreme adaptive optics, we are now able to resolve objects close to the diffraction limit of large telescopes, exploring new science cases. We introduce an integral field unit designed to couple light with a minimal plate scale from the SCExAO facility at NIR wavelengths to a single-mode spectrograph. The integral field unit has a 3D-printed micro-lens array on top of a custom single-mode multi-core fiber, to optimize the coupling of light into the fiber cores. We demonstrate the potential of the instrument via initial results from the first on-sky runs at the 8.2 m Subaru Telescope with a spectrograph using off-the-shelf optics, allowing for rapid development with low cost.

Computational optical imaging with a photonic lantern.

The thin and flexible nature of optical fibres often makes them the ideal technology to view biological processes in-vivo, but current microendoscopic approaches are limited in spatial resolution. Here, we demonstrate a route to high resolution microendoscopy using a multicore fibre (MCF) with an adiabatic multimode-to-single-mode "photonic lantern" transition formed at the distal end by tapering. We show that distinct multimode patterns of light can be projected from the output of the lantern by individually exciting the single-mode MCF cores, and that these patterns are highly stable to fibre movement. This capability is then exploited to demonstrate a form of single-pixel imaging, where a single pixel detector is used to detect the fraction of light transmitted through the object for each multimode pattern. A custom computational imaging algorithm we call SARA-COIL is used to reconstruct the object using only the pre-measured multimode patterns themselves and the detector signals.

Adiabatic higher-order mode microfibers based on a logarithmic index profile.

Optical fibers with a logarithmic index profile can provide invariant mode field diameters along a tapered fiber, which enables adiabatic mode transitions for higher-order mode (HOM) microfibers. A microfiber with a waist diameter of ∼2 µm is fabricated with an insertion loss lower than 0.03 dB for the LP01 and 0.11 dB for the LP11 mode. The concept of the low loss HOM microfibers can be further extended to include more than one fiber and a 2×2 few mode microfiber coupler is fabricated/characterized in our experiments. These single or multiple spatial channel HOM microfibers are beneficial for various applications, including in particle propulsion, atom trapping, optical sensing and space division multiplexed data transmission systems.

Observation of Rapid Adiabatic Passage in Optical Four-Wave Mixing.

We observe clear evidence of adiabatic passage between photon populations via a four-wave mixing process, implemented through a dispersion sweep arranged by a core diameter taper of an optical fiber. Photonic rapid adiabatic passage through the cubic electric susceptibility thus opens precise control of frequency translation between broadband light fields to all common optical media. Areas of potential impact include optical fiber and on-chip waveguide platforms for quantum information, ultrafast spectroscopy and metrology, and extreme light-matter interaction science.

Ultra-low background Raman sensing using a negative-curvature fibre and no distal optics.

Measuring Raman spectra through an optical fibre is usually complicated by the high intrinsic Raman scatter of the fibre material. Common solutions such as the use of multiple fibres and distal optics are complex and bulky. We demonstrate the use of single novel hollow-core negative-curvature fibres (NCFs) for Raman and surface-enhanced Raman spectroscopy (SERS) sensing using no distal optics. The background Raman emission from the silica in the NCF was at least 1000× smaller than in a conventional solid fibre, while maintaining the same collection efficiency. We transmitted pump light from a 785-nm laser through the NCF, and we collected back the weak Raman spectra of different distal samples, demonstrating the fibre probe can be used for measurements of weak Raman and SERS signals that would otherwise overlap spectrally with the silica background. The lack of distal optics and consequent small probe diameter (<0.25 mm) enable applications that were not previously possible.

Divide and conquer: an efficient solution to highly multimoded photonic lanterns from multicore fibres.

Photonic lanterns typically allow for single-mode action in a multimode fibre. Since their invention over a decade ago for applications in astrophotonics, they have found important uses in diverse fields of applied science. To date, large aperture highly-mulitmoded to single-mode lanterns have been difficult as fabrication techniques are not practical for mass replication. Here as a proof of concept, we demonstrate three different devices based on multicore fibre photonic lanterns with: 100µm core diameters; NAs = 0.16 and 0.15; and requiring 259 single-mode core system, specifically 7 multicore fibres each with 37 cores, instead of 259 individual single-mode fibres. The average insertion loss excluding coupling efficiencies is only 0.4dB (>91% transmission). This concept has numerous advantages, in particular, (i) it is a direct scaleable solution, (ii) eases imprinting of photonic functions, e.g. fibre Bragg gratings; and (iii) new approach for large-area optical fibre slicers for future large-aperture telescopes.

Multiplexed single-mode wavelength-to-time mapping of multimode light.

When an optical pulse propagates along an optical fibre, different wavelengths travel at different group velocities. As a result, wavelength information is converted into arrival-time information, a process known as wavelength-to-time mapping. This phenomenon is most cleanly observed using a single-mode fibre transmission line, where spatial mode dispersion is not present, but the use of such fibres restricts possible applications. Here we demonstrate that photonic lanterns based on tapered single-mode multicore fibres provide an efficient way to couple multimode light to an array of single-photon avalanche detectors, each of which has its own time-to-digital converter for time-correlated single-photon counting. Exploiting this capability, we demonstrate the multiplexed single-mode wavelength-to-time mapping of multimode light using a multicore fibre photonic lantern with 121 single-mode cores, coupled to 121 detectors on a 32 × 32 detector array. This work paves the way to efficient multimode wavelength-to-time mapping systems with the spectral performance of single-mode systems.

Quantitative characterization of endoscopic imaging fibers.

We describe a technique for the quantitative characterization of endoscopic imaging fibers using an interference pattern as the standard object to be imaged. The visibility of the pattern at the other end of the fiber is then analyzed as wavelength and fringe period are varied. We demonstrate the use of the technique by comparing three fibers: two fabricated in-house from the same preform, designed to minimize inter-core coupling at visible wavelengths less than 650 nm, and a commercial imaging fiber. The techniques discussed are currently being used to optimize fibers for fluorescence bronchoscopy to be used in intensive care clinics.

Characterizing the variation of propagation constants in multicore fiber.

We demonstrate a numerical technique that can evaluate the core-to-core variations in propagation constant in multicore fiber. Using a Markov Chain Monte Carlo process, we replicate the interference patterns of light that has coupled between the cores during propagation. We describe the algorithm and verify its operation by successfully reconstructing target propagation constants in a fictional fiber. Then we carry out a reconstruction of the propagation constants in a real fiber containing 37 single-mode cores. We find that the range of fractional propagation constant variation across the cores is approximately ± 2 × 10(-5).

Emission and nonradiative decay of nanodiamond NV centers in a low refractive index environment.

The nitrogen vacancy (NV) center is the most widely studied single optical defect in diamond with great potential for applications in quantum technologies. Development of practical single-photon devices requires an understanding of the emission under a range of conditions and environments. In this work, we study the properties of a single NV center in nanodiamonds embedded in an air-like silica aerogel environment which provides a new domain for probing the emission behavior of NV centers in nanoscale environments. In this arrangement, the emission rate is governed primarily by the diamond crystal lattice with negligible contribution from the surrounding environment. This is in contrast to the conventional approach of studying nanodiamonds on a glass coverslip. We observe an increase in the mean lifetime due to the absence of a dielectric interface near the emitting dipoles and a distribution arising from the irregularities in the nanodiamond geometry. Our approach results in the estimation of the mean quantum efficiency (~0.7) of the nanodiamond NV emitters.

Structure of plasmonic aerogel and the breakdown of the effective medium approximation.

A method for making aerogel doped with gold nanoparticles (GNPs) produces a composite material with a well-defined localized surface plasmon resonance peak at 520 nm. The width of the extinction feature indicates the GNPs are well dispersed in the aerogel, making it suited to optical study. A simple effective medium approximation cannot explain the peak extinction wavelengths. The plasmonic field extends on a scale where aerogel cannot be considered isotropic, so a new model is required: a 5 nm glass coating on the GNPs models the extinction spectrum of the composite material, with air (aerogel), methanol (alcogel), or toluene filling the pores.

Tapered fibers embedded in silica aerogel.

We have embedded thin tapered fibers (with diameters down to 1 microm) in silica aerogel with low loss. The aerogel is rigid but behaves refractively like air, protecting the taper without disturbing light propagation along it. This enables a new class of fiber devices exploiting volume evanescent interactions with the aerogel itself or with dopants or gases in the pores.