Novel Intrinsic Self-Healing Poly-Silicone-Urea with Super-Low Ice Adhesion Strength.

Accumulation of snow and ice often causes problems and even dangerous situations for both industry and the general population. Passive de-icing technologies, e.g., hydrophobic, liquid-infused bionic surfaces, have attracted more and more attention compared with active de-icing technologies, e.g., electric heating, hot air heating, due to the passive de-icing technology's lower energy consumption and sustainability footprint. Using passive de-icing coatings seems to be one of the most promising solutions. However, the previously reported de-icing coatings suffer from high ice adhesion strength or short service life caused by wear. An intrinsic self-healing material based on poly-silicone-urea is developed in this work to address these problems. The material is prepared by introducing dynamic disulfide bonds into the hard phase of the polymer. Experimental results indicate that this poly-silicone-urea has a self-healing efficiency of close to 99%. More interestingly, it is found that the coating prepared from this poly-silicone-urea has a super low ice adhesion force, only 7 ± 1 kPa, which is almost the lowest value compared with previous intrinsic self-healing de-/anti-icing reports. This material can maintain low ice adhesion strength after healing. This intrinsic self-healing poly-silicone-urea can meet several practical applications, opening the door for future sustainable anti-/de-icing technologies.

Precise control of operating conditions in tribotesting with respect to trace humidity and contact temperature.

Research in tribology are often connected to tribosystems operating in specific environments, where climate chambers are needed for tribotesting to resemble the environmental conditions in the real application. Although the effect of humidity on the tribological performance of many materials and lubricants is evident, many studies are conducted without sufficient systems to accurately monitor and control the humidity level throughout testing. In this paper, a humidity controlling system was developed to enable continuous monitoring and precise control of the humidity at trace moisture levels. The climate controller was validated in a tri-pin-on-disc tribometer with excellent performance and can be fitted to most climate chambers. To further improve the control of operating conditions during tribotesting, a thermodynamic simulation of the contact temperature was developed.•The developed climate controller is a simple and cost-effective method to accurately monitor and control the humidity in a climate chamber at trace moisture levels.•The portable design of the humidity controller enables use with most climate chambers and enclosed tribometers.•To have better control over the temperature in the sliding interface during testing, a thermodynamic simulation method was used to estimate contact temperature between sliding bodies from near-contact temperature measurements and the measured friction forces.

Lubricant film formation in rough surface non-conformal conjunctions subjected to GPa pressures and high slide-to-roll ratios.

A ball-on-disc machine was employed in a highly idealised setting to study the interplay between oil film formation and surface irregularities in single-sided rough elasto-hydrodynamic lubricated (EHL) conjunctions. The tests were operated under GPa pressures and high slide-to-roll ratios in a situation where the separating gap was smaller than the combined surface roughness height. Under the initial state of solid contact interference and with the operating conditions held fixed, surfaces were found to gradually conform such that a fully separating oil film of nanometre thickness eventually developed-a thin film lubrication state known as micro-EHL. Additionally, with a previously developed approach for 3D surface re-location analysis, we were able to very precisely specify the pertained nature of surface transformations, even at the asperity scale, by comparing the post-test surfaces to those in the virgin state. The surface roughness Sq was reduced by up to 17% after running-in, while the speed required for full film EHL was reduced by a remarkable 90%. Hence, full film EHL is possible even in cases where the Λ-ratio falsely suggests boundary lubrication. This discrepancy was attributed to the way surfaces are deformed inside the contact, i.e., through the establishment of micro-EHL.

A smart friction control strategy enabled by CO2 absorption and desorption.

Intelligent control of friction is an attractive but challenging topic and it has rarely been investigated for full size engineering applications. In this work, it is instigated if it would be possible to adjust friction by controlling viscosity in a lubricated contact. By exploiting the ability to adjust the viscosity of the switchable ionic liquids, 1,8-Diazabicyclo (5.4.0) undec-7-ene (DBU)/ glycerol mixture via the addition of CO2, the friction could be controlled in the elastohydrodynamic lubrication (EHL) regime. The friction decreased with increasing the amount of CO2 to the lubricant and increased after partial releasing CO2. As CO2 was absorbed by the liquid, the viscosity of the liquid increased which resulted in that the film thickness increased. At the same time the pressure-viscosity coefficient decreased with the addition of CO2. When CO2 was released again the friction increased and it was thus possible to control friction by adding or removing CO2.