RESUMO
The aim of this study was to evaluate in vivo the influence of the native oxide layer on osseointegration and new bone formation on the surface of atmospheric plasma-sprayed porous titanium coatings. Porous titanium coatings were deposited on all implant surfaces, and half of the samples were subsequently submitted to oxide layer removal treatment. Samples were implanted onto the cortical bone of sheep (tibia) and evaluated at 30 and 60 days. Implants were removed en bloc and the attachment of bone to implants was examined by tensile pull-out test (osseointegration assessment), light microscopy, scanning electron microscopy (histological analysis), and instrumented hardness tests (mechanical properties of mature and newly formed bone tissue). Coatings submitted to oxide layer treatment presented higher osseointegration values at both healing periods and showed more mature and mineralized bone tissue when compared with nontreated coatings. Our findings showed that the use of acid-etching in association with atmospheric plasma spraying techniques improves osseointegration of titanium implants.
Assuntos
Materiais Revestidos Biocompatíveis/química , Implantes Experimentais , Osseointegração , Gases em Plasma/química , Titânio/química , Animais , Feminino , Ovinos , Propriedades de SuperfícieRESUMO
The purpose of this study was to evaluate the mechanical behavior of three composites with nanoparticles Filtek Z350 XT (3M ESPE), Esthet X (Dentsply), Grandio (Voco) in enamel and body shades (A2) trough nanohardness, elastic modulus, compressive strength test, flexural strength test, diametral tensile strength, flexural modulus, weight filler content and Knoop microhardness. One sample of each material was submitted to nanohardness and elastic modulus. Five values of ten indentations were considered valids inside confidence intereval. Ten samples of each material were submitted to compressive strength, flexural strength and diametral tensile strength test at universal testing machine. The flexural modulus test was calculated based on flexural strength results. Ten samples of each group were submitted to knoop microhardness test. The results were submitted to ANOVA and Tukey statistical tests. The highest inorganic weight filler content for Grandio was registered after the organic mould decomposition. After statistical analysis Grandio showed the highest averages for nanohardness, elastic modulus, flexural modulus and knoop microhardness. For diametral tensile strength Grandio and Filtek Z350 XT obtained the highest averages. The tested composite resins ranged similar medias statistically for compressive strength. For flexural strength Filtek Z350 XT and Esthet X showed the highest averages. The results suggest that the weight filler content, the filler size and shape and the contact surface between nanofillers and organic phase has direct relation with composite resins with nanoparticles mechanical properties. Further studies should be carried out to improve the knowledge of composites with nanoparticles mechanical behavior.
Assuntos
Resinas Compostas/química , Nanocompostos/química , Análise do Estresse Dentário , Teste de Materiais , Fenômenos MecânicosRESUMO
This study evaluated the effect of low-level laser therapy (LLLT) on the chemical composition, crystallinity and crystalline structure of bone at the site of distraction osteogenesis. Five rabbits were subjected to distraction osteogenesis (latency = 3 days; rate and frequency = 0.7 mm/day for 7 days; consolidation = 10 days), and three were given LLLT with arsenide-gallium-aluminum (AsGaAl; 830 nm, 40 mW): 10 J/cm(2) dose per spot, applied directly to the distraction osteogenesis site during the consolidation stage at 48 h intervals. Samples were harvested at the end of the consolidation stage. X-ray fluorescence and X-ray diffraction were used to analyze chemical composition, crystallinity and crystalline structure of bone at the distraction osteogenesis site. The analysis of chemical composition and calcium (Ca) and phosphorus (P) ratios revealed greater mineralization in the LLLT group. Diffractograms showed that the crystalline structure of the samples was similar to that of hydroxyapatites. Crystallinity percentages were greater in rabbits that were given LLLT. Crystallinity (41.14% to 54.57%) and the chemical composition of the bone at the distraction osteogenesis site were similar to the that of the control group (42.37% to 49.29%). The results showed that LLLT had a positive effect on the biomodulation of newly formed bone.
Assuntos
Regeneração Óssea/efeitos da radiação , Terapia com Luz de Baixa Intensidade , Osteogênese por Distração , Osteogênese/efeitos da radiação , Animais , Osso e Ossos/química , Osso e Ossos/efeitos da radiação , Cálcio/análise , Masculino , Fósforo/análise , Coelhos , Espectrometria por Raios X , Difração de Raios XRESUMO
A new, low cost, pulsed-DC plasma-enhanced chemical vapor deposition system that uses a bipolar, pulsed power supply was designed and tested to evaluate its capacity to produce quality diamond-like carbon films on the inner surface of steel tubes. The main focus of the study was to attain films with low friction coefficients, low total stress, a high degree of hardness, and very good adherence to the inner surface of long metallic tubes at a reasonable growth rate. In order to enhance the diamond-like carbon coating adhesion to metallic surfaces, four steps were used: (1) argon ion sputtering; (2) plasma nitriding; (3) a thin amorphous silicon interlayer deposition, using silane as the precursor gas; and (4) diamond-like carbon film deposition using methane atmosphere. This paper presents various test results as functions of the methane gas pressure and of the coaxial metal anode diameter, where the pulsed-DC voltage constant is kept constant. The influence of the coaxial metal anode diameter and of the methane gas pressure is also demonstrated. The results obtained showed the possibilities of using these DLC coatings for reduced friction and to harden inner surface of the steel tubes.
RESUMO
The use of multi-component femoral implants to replace the femur head and re-establish bone motion has been widespread since the 70s. Frequently these implants have spherical metallic heads made of, for example, 316-L stainless steel or Cr-Co alloys, which allow rotational motion towards a polymeric component (UHMWPE). One of the major causes of implant rejection is the generation of UHMWPE debris on the surface between the implant head and the polymeric component. The gamma ray sterilization of implants and the periodical X-ray medical control could contribute to premature degradation of the polymeric surface, resulting in increased wear and shortened lifetime of the implant. In this work we study the degradation degree of the polymeric UHMWPE component as function of the X-ray dose. The elasto-plastic deformation and recovery were carried out by means of a nanohardness tester equipment and the polymer degradation was measured using a fast Fourier transform infra-red (FT-IR) equipment. The results show the compromise among the irradiation doses, the surface oxidation and the mechanical properties of the samples.