Poly(Allylamine Hydrochloride) and ZnO Nanohybrid Coating for the Development of Hydrophobic, Antibacterial, and Biocompatible Textiles.

In healthcare facilities, infections caused by Staphylococcus aureus (S. aureus) from textile materials are a cause for concern, and nanomaterials are one of the solutions; however, their impact on safety and biocompatibility with the human body must not be neglected. This study aimed to develop a novel multilayer coating with poly(allylamine hydrochloride) (PAH) and immobilized ZnO nanoparticles (ZnO NPs) to make efficient antibacterial and biocompatible cotton, polyester, and nylon textiles. For this purpose, the coated textiles were characterized with profilometry, contact angles, and electrokinetic analyzer measurements. The ZnO NPs on the textiles were analyzed by scanning electron microscopy and inductively coupled plasma mass spectrometry. The antibacterial tests were conducted with S. aureus and biocompatibility with immortalized human keratinocyte cells. The results demonstrated successful PAH/ZnO coating formation on the textiles, demonstrating weak hydrophobic properties. Furthermore, PAH multilayers caused complete ZnO NP immobilization on the coated textiles. All coated textiles showed strong growth inhibition (2-3-log reduction) in planktonic and adhered S. aureus cells. The bacterial viability was reduced by more than 99%. Cotton, due to its better ZnO NP adherence, demonstrated a slightly higher antibacterial performance than polyester and nylon. The coating procedure enables the binding of ZnO NPs in an amount (<30 µg cm-2) that, after complete dissolution, is significantly below the concentration causing cytotoxicity (10 µg mL-1).

Dextran-based antibacterial hydrogel-derived fluorescent sensors for the visual monitoring of AgNPs.

The unpredictable release behavior of metal nanoparticles/metal ions from metal nanoparticle-loaded hydrogels, without a suitable in situ detection method, is resulting in serious cytotoxicity. To optimize the preparation and design of antibacterial hydrogels for in situ detection of metal nanoparticles, an in-situ detection platform based on the fluorescence signal change caused by the potential surface energy transfer of silver nanoparticles (AgNPs) and carbon dots (CD) through silver mirror reaction and Schiff base reaction was established. The antimicrobial test results show that the composite antimicrobial hydrogel, with lower dosages of AgNPs and CD, exhibited a higher inhibition rate of 99.1 % against E. coli and 99.8 % against S. aureus compared to the single antimicrobial component. This suggests a potential synergistic antimicrobial activity. Furthermore, the fluorescence detection platform was established with a difference of <3 µg between detected values and actual values over a period of 72 h. This demonstrates the excellent in situ detection capability of the hydrogel in antimicrobial-related applications.

Antibacterial evaluation of different prosthetic liner textiles coated by CuO nanoparticles.

Prosthetic liners are mainly used as an interface between residual limbs and prosthetic sockets to minimize physical and biological damage to soft tissue. However, the closed and moist conditions within liners and the amputee's skin provide a suitable environment for bacterial growth to cause infections. This study aimed to coat a comprehensive variant material with copper oxide nanoparticles (CuO NPs) and compare their surface analysis and antibacterial properties. These materials were covered with CuO NPs solution at a concentration of 70 µg mL-1 to achieve this purpose. After drying, their surface characteristics were analyzed by measuring zeta potential, contact angle, surface roughness, and fiber arrangement. Cu-released concentration from the coatings into the acetate buffer solution by inductively coupled plasma mass spectrometry indicated that lycra and nylon quickly released Cu ions to concentrations up to ∼0.2 µg mL-1 after 24 h, causing low metabolic activity of human bone-marrow mesenchymal stem cells (bMSC) in the indirect assay. Antibacterial activity of the coated specimens was evaluated by infecting their surfaces with the Gram-positive bacteria Staphylococcus epidermidis, reporting a significant ∼40 % reduction of metabolic activity for x-dry after 24 h; in addition, the number of viable bacterial colonies adhered to the surface of this material was reduced by ∼23 times in comparison with non-treated x-dry that were visually confirmed by scanning electron microscope. In conclusion, CuO NPs x-dry shows optimistic results to pursue further experiments due to its slow speed of Cu release and prolonged antibacterial activity, as well as its compatibility with human cells.

Cation Adsorption in TiO2 Nanotubes: Implication for Water Decontamination.

TiO2 nanotubes constitute very promising nanomaterials for water decontamination by the removal of cations. We combined a range of experimental techniques from structural analyses to measurements of the properties of aqueous suspensions of nanotubes, with (i) continuous solvent modeling and (ii) quantum DFT-based simulations to assess the adsorption of Cs+ on TiO2 nanotubes and to predict the separation of metal ions. The methodology is set to be operable under realistic conditions, which, in this case, include the presence of CO2 that needs to be treated as a substantial contaminant, both in experiments and in models. The mesoscopic model, based on the Poisson-Boltzmann equation and surface adsorption equilibrium, predicts that H+ ions are the charge-determining species, while Cs+ ions are in the diffuse layer of the outer surface with a significant contribution only at high concentrations and high pH. The effect of the size of nanotubes in terms of the polydispersity and the distribution of the inner and outer radii is shown to be a third-order effect that is very small when the nanotube layer is not very thick (ranging from 1 to 2 nm). Besides, DFT-based molecular dynamics simulations demonstrate that, for protonation, the one-site and successive association assumption is correct, while, for Cs+ adsorption, the size of the cation is important and the adsorption sites should be carefully defined.

Antifungal Effect of Polymethyl Methacrylate Resin Base with Embedded Au Nanoparticles.

Full and partial restorations in dentistry must replicate the characteristics of the patient's natural teeth. Materials must have good mechanical properties and be non-toxic and biocompatible. Microbes, which can form biofilms, are constantly in contact with restorations. In this study, we investigate how well Candida albicans adheres to a polymethyl methacrylate (PMMA) resin base with gold (Au) nanoparticles. We synthesized Au nanoparticles and characterized them. The average size of Au nanoparticles embedded in PMMA was 11 nm. The color difference ΔE between PMMA and PMMA/Au composites was 2.7 and was still esthetically acceptable to patients. PMMA/Au surfaces are smoother and more hydrophilic than pure PMMA surfaces, and the isoelectric point of both types of surfaces was 4.3. Above the isoelectric point, PMMA/Au surfaces are more negatively charged than PMMA surfaces. The added Au nanoparticles decreased the tensile strength, while the hardness did not change significantly. Adhesion measurements showed that PMMA surfaces modified with Au nanoparticles reduced the extent of microbial adhesion of Candida albicans.

Coarse-grained molecular dynamics simulation of cation distribution profiles on negatively charged lipid membranes during phase separation.

Revealing the ion distributions on a charged lipid membrane in aqueous solution under the influence of long-range interactions is essential for understanding the origin of the stability of the bilayer structure and the interaction between biomembranes and various electrolytes. However, the ion distributions and their dynamics associated with the phase separation process of the lipid bilayer membrane are still unclear. We perform coarse-grained molecular dynamics simulations to reveal the Na+ and Cl- distributions on charged phospholipid bilayer membranes during phase separation. During the phase separation, cations closely follow the position of negatively charged lipids on a microsecond timescale and are rapidly redistributed parallel to the lipid bilayer. In the homogenous mixture of zwitterionic and negatively charged lipids, cations weakly follow negatively charged lipids, indicating the strong interaction between cations and negatively charged lipids. We also compare cation concentrations as a function of surface charge density obtained by our simulation with those obtained by a modified Poisson-Boltzmann theory. Including the ion finite size makes the statistical results consistent, suggesting the importance of the ion-ion interactions in aqueous solution. Our simulation results advance our understanding of ion distribution during phase separation.

Suppressing the Hofmeister Anion Effect by Thermal Annealing of Thin-Film Multilayers Made of Weak Polyelectrolytes.

Thin films made of weak polyelectrolytes poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) have been fabricated on silicon wafers using the layer-by-layer (LbL) method. To study the influence of counteranion type on the growth and properties of PAH/PAA multilayers, the nature of the supporting sodium salt was varied from cosmotropic to chaotropic anions (F-, Cl-, and ClO4 -). Results of ellipsometry and AFM measurements indicate that the film thickness and surface roughness systematically increase on the order F- < Cl- < ClO4 -. Furthermore, we found that the hydrophobicity of the PAH/PAA multilayer also follows the described trend when a polycation is the terminating layer. However, the heating of PAH/PAA multilayers to 60 °C during the LbL assembly suppressed the influence of background anions on the multilayer formation and properties. On the basis of the obtained results, it could be concluded that thermal annealing induces changes at the polymer-air interface in the sense of reorientation and migration of polymer chains.

Role of Substrate Type in the Process of Polyelectrolyte Multilayer Formation.

Polyelectrolyte multilayers are coatings formed by the alternate deposition of polycations and polyanions on a charged surface. In this study we examined how the type of substrate affects a multilayer prepared from poly(allylamine hydrochloride) and poly(acrylic acid). Silicon and titanium wafers were used as substrates. Their properties were systematically studied using ellipsometry, tensiometry, atomic force microscopy and streaming potential measurements. Multilayers were built up at pH = 7 with tetramethylammonium chloride as the background salt. The growth of films was monitored by ellipsometry, while the morphology and surface roughness were determined by atomic force microscopy. It was found that the thickness of multilayers containing 10 layers on silicon is 10 nm, whereas the thickness of the same film on titanium is three times higher. It was shown that multilayers formed on silicon display a grain-like structure, which was not the case for a film formed on titanium. Such morphological properties are also reflected in the surface roughness. Finally, it was shown that, in addition to the electrostatic interactions, the hydrophobicity of the substrate also plays an important role in the polyelectrolyte multilayer formation process and influences its thickness and properties.

Nanoparticles: From synthesis to applications and beyond.

In modern-day research, nanoparticles (size < 100nm) are an indispensable tool for various applications, especially in the field of biomedicine. Although enormous efforts have been made to understand the properties and specificities of nanoparticles, many questions are still not answered and the new ones arise. In this review we summarize current trends in the nanoparticle synthesis and characterization and interpret the stability of nanoparticles in various media from aqueous solutions to biological milieu important for the in vitro and in vivo studies. To get more detailed insight into nanoparticle charging properties and interactions of nanoparticles with interfaces the theoretical models are presented. Finally, the overview of nanoparticle applications is given and the future prospects are discussed.

Influence of Charge Lipid Head Group Structures on Electric Double Layer Properties.

In this study we derived a model for a multicomponent lipid monolayer in contact with an aqueous solution by means of a generalized classical density functional theory and Monte Carlo simulations. Some of the important biological lipid systems were studied as monolayers composed of head groups with different shapes and charge distributions. Starting from the free energy of the system, which includes the electrostatic interactions, additional internal degrees of freedom are included as positional and orientational entropic contributions to the free energy functional. The calculus of variation was used to derive Euler-Lagrange equations, which were solved numerically by the finite element method. The theory and Monte Carlo simulations predict that there are mainly two distinct regions of the electric double layer: (1) the interfacial region, with thickness less than or equal to the length of the fully stretched conformation of the lipid head group, and (2) the outside region, which follows the usual screening of the interface. In the interfacial region, the electric double layer is strongly perturbed, and electrostatic profiles and ion distributions have functionality distinct to classical mean-field theories. Based purely on Coulomb interactions, the theory suggests that the dominant effect on the lipid head group conformation is from the charge density of the interface and the structured lipid mole fraction in the monolayer, rather than the salt concentration in the system.

Biophysical Properties of Foamed and Solid Polymers Used in Orthotics and Prosthetics.

Orthotic and prosthetic materials should have good mechanical and antibacterial properties. Therefore, in our study, we consider four common foamed closed-cells and two solid polymeric materials regarding their mechanical behaviour and tendency for bacterial adhesion. For all materials, the surface roughness, hydrophobicity, zeta potential, tensile properties, hardness and CIE color parameters were measured. We found that foamed polymeric materials have higher roughness, higher hydrophobicity, lower Young's modulus, lower maximum tensile strength and lower hardness than solid materials. Bacterial adhesion test measurements based on observation by scanning electron microscopy show much a lower adhesion extent of S. aureus on solid materials than on foamed materials. The measured biophysical properties could be the key data for users to select the optimal materials.

Three-Phase Coexistence in Binary Charged Lipid Membranes in a Hypotonic Solution.

We investigated the phase separation of dioleoylphosphatidylserine (DOPS) and dipalmitoylphosphatidylcholine (DPPC) in giant unilamellar vesicles in a hypotonic solution using fluorescence and confocal laser scanning microscopy. Although phase separation in charged lipid membranes is generally suppressed by the electrostatic repulsion between the charged headgroups, osmotic stress can promote the formation of charged lipid domains. Interestingly, we observed a three-phase coexistence even in the DOPS/DPPC binary lipid mixtures. The three phases were DPPC-rich, dissociated DOPS-rich, and nondissociated DOPS-rich phases. The two forms of DOPS were found to coexist owing to the ionization of the DOPS headgroup, such that the system could be regarded as quasi-ternary. The three formed phases with differently ionized DOPS domains were successfully identified experimentally by monitoring the adsorption of positively charged particles. In addition, coarse-grained molecular dynamics simulations confirmed the stability of the three-phase coexistence. Attraction mediated by hydrogen bonding between protonated DOPS molecules and reduction of the electrostatic interactions at the domain boundaries stabilized the three-phase coexistence.

Bacterial Adhesion of Streptococcus mutans to Dental Material Surfaces.

The aim of this study was to investigate and understand bacterial adhesion to different dental material surfaces like amalgam, Chromasit, an Co-Cr alloy, an IPS InLine ceramic, yttrium stabilized tetragonal polycrystalline zirconia (TPZ), a resin-based composite, an Au-Pt alloy, and a tooth. For all materials, the surface roughness was assessed by profilometry, the surface hydrophobicity was determined by tensiometry, and the zeta potential was measured by electrokinetic phenomena. The arithmetic average roughness was the lowest for the TPZ ceramic (Ra = 0.23 µm ± 0.02 µm), while the highest value was observed for the Au-Pt alloy (Ra = 0.356 µm ± 0.075 µm). The hydrophobicity was the lowest on the TPZ ceramic and the highest on the Co-Cr alloy. All measured streaming potentials were negative. The most important cause of tooth caries is the bacterium Streptococcus mutans, which was chosen for this study. The bacterial adhesion to all material surfaces was determined by scanning electron microscopy. We showed that the lowest bacterial extent was on the amalgam, whereas the greatest extent was on tooth surfaces. In general, measurements showed that surface properties like roughness, hydrophobicity and charge have a significant influence on bacterial adhesion extent. Therefore, dental material development should focus on improving surface characteristics to reduce the risk of secondary caries.

Interactions of zein and zein/rosin nanoparticles with natural polyanion gum arabic.

The objective of this study was to investigate interactions of zein (Z) and zein/rosin (Z/R) nanoparticles with gum arabic (GA), at different pH. Nanoparticles were firstly prepared by antisolvent precipitation of biopolymers from aqueous ethanol solutions. Nanoparticles suspensions were then dialyzed against water in order to remove ethanol and other impurities, and water suspensions of zein and zein/rosin nanoparticles were obtained. It was shown that composition of nanoparticles affects their surface charge density. Zeta potential of nanoparticles was positive without GA and changed to negative after addition of GA, at all pH tested. SEM analysis proved both Z and Z/R nanoparticles to be spherical and in size around 200 nm. The effect of addition of GA on particle size was determined using dynamic light scattering method. It was found that addition of GA increases size of nanoparticles at pH = 4 and pH = 5.5, from 150 - 220 nm to 250 - 320 nm. However, at pH = 3 it causes aggregation process, and diameter of particles increases up to few micrometres. Isothermal titration calorimetry was used to measure enthalpy changes in reaction between Z or Z/R nanoparticles and GA. Results showed that reaction between GA and Z or Z/R NPs is exothermic at each pH tested, except for Z NPs at pH = 3, where it was endothermic. At presented pHs, Z/R NPs were less charged compared to Z NPs, and their surface get saturated with GA molecules more rapidly. Z NPs showed greater enthalpy change in reaction with GA, compared to Z/R NPs.

Bacterial adhesion on orthopedic implants.

Orthopedic implants are routinely used for fixation of fractures, correction of deformities, joint replacements, and soft tissue anchorage. Different biomaterials have been engineered for orthopedic implants. Previously, they were designed merely as mechanical devices, now new strategies to enhance bone healing and implant osteointegration via local delivery of molecules and via implant coatings are being developed. These biological coatings should enhance osteointegration and reduce foreign body response or infection. This article reviews current and future orthopedic implants, materials and surface characteristics, biocompatibility, and mechanisms of bacterial adhesion. Additionally, the review is addressing implant-related infection, the main strategies to prevent it and suggest possible future research that may control implant related-infection.

Bacterial adhesion rate on food grade ceramics and Teflon as kitchen worktop surfaces.

Here we present a research of bacterial adhesion to two most often used materials in modern kitchens, namely food grade ceramics and Teflon. To test the bacterial adhesion on kitchen worktops Escherichia coli, Pseudomonas aeruginosa and Campylobacter jejuni were used as the most common foodborne contaminants. Contact angle, roughness and streaming potential measurements were used for surface characterization. Crystal violet staining and scanning electron microscopy were applied for bacterial adhesion analysis. We showed that the adhesion of tested bacteria strains was lower on the Teflon surface compared to the ceramics. The hydrophobicity of the surface substantially contributed to the bacterial adhesion rate. On the other hand, the surface roughness and charge did not play a crucial role in the adhesion process.

Spherical Polyelectrolyte Brushes as Templates to Prepare Hollow Silica Spheres Encapsulating Metal Nanoparticles.

Integrating hollow silica spheres with metal nanoparticles to fabricate multifunctional hybrid materials has attracted increasing attention in catalysis, detection, and drug delivery. Here, we report a simple and general method to prepare hollow silica spheres encapsulating silver nanoparticles (Ag@SiO2) based on spherical polyelectrolyte brushes (SPB), which consist of a polystyrene core and densely grafted poly (acrylic acid) (PAA) chains. SPB were firstly used as nanoreactors to generate silver nanoparticles in situ and then used as sacrificial templates to prepare hybrid hollow silica spheres. The resulted Ag@SiO2 composites exhibit high catalytic activity and good reusability for the reduction of 4-nitrophenol to 4-aminophenol by NaBH4. More importantly, this developed approach can be extended to the encapsulation of other metal nanoparticles such as gold nanoparticles into the hollow silica spheres. This work demonstrates that SPB are promising candidates for the preparation of hollow spheres with encapsulated metal nanoparticles and the resulted hybrid spheres show great potential applications in catalysis.

Synergistic Solvent Extraction Is Driven by Entropy.

In solvent extraction, the self-assembly of amphiphilic molecules into an organized structure is the phenomenon responsible for the transfer of the metal ion from the aqueous phase to the organic solvent. Despite their significance for chemical engineering and separation science, the forces driving the solute transfer are not fully understood. Instead of assuming the simple complexation reaction with predefined stoichiometry, we model synergistic extraction systems by a colloidal approach that explicitly takes into account the self-assembly resulting from the amphiphilic nature of the extractants. Contrary to the current paradigm of simple stoichiometry behind liquid-liquid extraction, there is a severe polydispersity of aggregates completely different in compositions, but similar in the free energy. This variety of structures on the nanoscale is responsible for the synergistic transfer of ions to the organic phase. Synergy can be understood as a reciprocal effect of chelation: it enhances extraction because it increases the configurational entropy of an extracted ion. The global overview of the complex nature of a synergistic mixture shows different regimes in self-assembly, and thus in the extraction efficiency, which can be tuned with respect to the green chemistry aspect.

Biofouling of stainless steel surfaces by four common pathogens: the effects of glucose concentration, temperature and surface roughness.

There is a wide range of factors affecting bacterial adhesion and biofilm formation. However, in both food processing and medical settings, it is very hard to obtain suitably controlled conditions so that the factors that reduce surface colonisation and biofouling can be studied. The aim of this study was to evaluate the effect of glucose concentration, temperature and stainless steel (SS) surface roughness on biofouling by four common pathogens (Escherichia coli, Staphylococcus aureus, Pseudomonas aeruginosa and L. monocytogenes). Among the tested variables, the untreated SS surface (3C) was shown to be fouled more than 3D polished, brushed or electropolished SS surfaces. Although an array of parameters influenced biofouling, the most promising control measure was the influence of low temperature (4 °C) that reduced biofouling even in the case of the psychrophilic Listeria monocytogenes. The study findings could significantly contribute to the prevention of SS surface contamination and consequential biofouling by food and healthcare associated pathogens.

Interaction between charged lipid vesicles and point- or rod-like trivalent ions.

This work examines the influence of the charge distribution of trivalent cations on their interaction with soft anionic particles, using a combination of experimental measurements and theoretical modelling. In particular, we perform electrophoresis measurements to determine the zeta-potential of anionic liposomes in the presence of spermidine and lanthanum cations. We work in a range of electrolyte concentration where a reversal in the electrophoretic mobility of the liposomes is expected; however, unlike the case of lanthanum cations, spermidine does not induce mobility reversal of liposomes. As a result, the charge distribution within the counterion appears to be a key factor. This conclusion is supported by a theory that accounts for intra-ionic correlations, which has previously been successfully used to describe the colloidal electric double layer. It allows us to model spermidine as rod-like ions and lanthanum cations as point-like ions in order to test the importance of the ionic geometry in the interactions with soft particles such as lipid vesicles.