RESUMO
Cotton cloth waste was used as a precursor to prepare activated carbon (ACCs) chemically activated with phosphoric acid. Adsorption behavior of prepared ACCs was correlated with physicochemical proprieties. The pore volume and BET surface of ACCs were determined by nitrogen adsorption isotherms and scanning electron microscopy was used to observe their surface morphologies. Fourier transform infrared (FTIR) spectroscopy analysis and pH point zero charge (pHPZC) were conducted to determine chemical properties. Under the optimal conditions: 50% impregnation ratio and thermal treatment under N2 flow at 600 °C during 60 min, the activated carbon prepared exhibits a high surface area 1,150 m2/g, 0.501 cm3/g micropore volume and an excellent adsorption performance. The adsorbed amount of clofibric acid is found to be 9.98 and 83 mg/g at, respectively, initial CA concentration of 10 and 100 mg/L at pH 3.0 and 20 °C. Diffusion and chemisorption are the steps controlling the adsorption of CA onto ACC 50% and the equilibrium data were well described by Freundlich isotherm.
Assuntos
Carvão Vegetal , Poluentes Químicos da Água , Adsorção , Ácido Clofíbrico , Concentração de Íons de Hidrogênio , Cinética , Ácidos Fosfóricos , Espectroscopia de Infravermelho com Transformada de Fourier , Poluentes Químicos da Água/análiseRESUMO
In this work, inexpensive and easily available olive stone (OS) waste was used as the source material to prepare activated carbons (ACs) by chemical activation with phosphoric acid and zinc chloride. The mixture design of experiments (MDOE) method was applied to study the effect of the composition of the mixture of unmodified olive stones (UOS) and ACs prepared from olive stones activated with ZnCl2 (ACOS ZnCl2) and H3PO4 (ACOS H3PO4) on the absorption of pharmaceutical residues. The adsorbed tetracycline (TC) amounts at equilibrium predicted from the model equation developed using Microsoft Excel were found to be in good agreement with the experimental values (R2 = 0.999). Based on the results of the model, the amount of TC removed increased as the proportion of ACOS H3PO4 in the adsorbent mixture increased and the highest amount of TC adsorbed was obtained with an adsorbent made up entirely of ACOS H3PO4. Separate adsorption tests for sulfamethazine (SMT) and amoxicillin (AMX) on ACOS H3PO4 showed that SMT was adsorbed best (189.81 mg/g), followed by TC (183.11 mg/g) then AMX (155.69 mg/g). However, when these molecules were present together in the same solution, it was TC that adsorbed best, followed by SMT then AMX. In addition to this, the sorption process studied was best described by a pseudo-first-order model and it was the Langmuir model that satisfactorily described the equilibrium data.
Assuntos
Olea , Poluentes Químicos da Água , Adsorção , Carvão Vegetal , CinéticaRESUMO
Lignocellulosic materials are good precursors for the production of activated carbon. In this work, coffee residue has been used as raw material in the preparation of powder activated carbon by the method of chemical activation with zinc chloride for the sorption of Pb(II) from dilute aqueous solutions. The influence of impregnation ratio (ZnCl2/coffee residue) on the physical and chemical properties of the prepared carbons was studied in order to optimize this parameter. The optimum experimental condition for preparing predominantly microporous activated carbons with high pore surface area (890 m2/g) and micropore volume (0.772 cm3/g) is an impregnation ratio of 100%. The developed activated carbon shows substantial capability to sorb lead(II) ions from aqueous solutions and for relative impregnation ratios of 75 and 100%, the maximum uptake is practically the same. Thus, 75% represents the optimal impregnation ratio. Batch experiments were conducted to study the effects of the main parameters such as contact time, initial concentration of Pb(II), solution pH, ionic strength and temperature. The maximum uptake of lead(II) at 25 degrees C was about 63 mg/g of adsorbent at pH 5.8, initial Pb(II) concentration of 10 mg/L, agitation speed of 200 rpm and ionic strength of 0.005 M. The kinetic data were fitted to the models of pseudo-first order and pseudo-second order, and follow closely the pseudo-second order model. Equilibrium sorption isotherms of Pb(II) were analyzed by the Langmuir, Freundlich and Temkin isotherm models. The Freundlich model gives a better fit than the others. Results from this study suggest that activated carbon produced from coffee residue is an effective adsorbent for the removal of lead from aqueous solutions and that ZnCl2 is a suitable activating agent for the preparation of high-porosity carbons.