Piezoelectric Energy Harvester Technologies: Synthesis, Mechanisms, and Multifunctional Applications.

Piezoelectric energy harvesters have gained significant attention in recent years due to their ability to convert ambient mechanical vibrations into electrical energy, which opens up new possibilities for environmental monitoring, asset tracking, portable technologies and powering remote "Internet of Things (IoT)" nodes and sensors. This review explores various aspects of piezoelectric energy harvesters, discussing the structural designs and fabrication techniques including inorganic-based energy harvesters (i.e., piezoelectric ceramics and ZnO nanostructures) and organic-based energy harvesters (i.e., polyvinylidene difluoride (PVDF) and its copolymers). The factors affecting the performance and several strategies to improve the efficiency of devices have been also explored. In addition, this review also demonstrated the progress in flexible energy harvesters with integration of flexibility and stretchability for next-generation wearable technologies used for body motion and health monitoring devices. The applications of the above devices to harvest various forms of mechanical energy are explored, as well as the discussion on perspectives and challenges in this field.

Precursor-Engineered Volatile Inks Enable Reliable Blade-Coating of Cesium-Formamidinium Perovskites Toward Fully Printed Solar Modules.

Reliable fabrication of large-area perovskite films with antisolvent-free printing techniques requires high-volatility solvents, such as 2-methoxyethanol (2ME), to formulate precursor inks. However, the fabrication of high-quality cesium-formamidinium (Cs-FA) perovskites has been hampered using volatile solvents due to their poor coordination with the perovskite precursors. Here, this issue is resolved by re-formulating a 2ME-based Cs0.05FA0.95PbI3 ink using pre-synthesized single crystals as the precursor instead of the conventional mixture of raw powders. The key to obtaining high-quality Cs-FA films lies in the removal of colloidal particles from the ink and hence the suppression of colloid-induced heterogeneous nucleation, which kinetically facilitates the growth of as-formed crystals toward larger grains and improved film crystallinity. Employing the precursor-engineered volatile ink in the vacuum-free, fully printing processing of solar cells (with carbon electrode), a power conversion efficiency (PCE) of 19.3%, a T80 (80% of initial PCE) of 1000 h in ISOS-L-2I (85 °C/1 Sun) aging test and a substantially reduced bill of materials are obtained. The reliable coating methodology ultimately enables the fabrication of carbon-electrode mini solar modules with a stabilized PCE of 16.2% (average 15.6%) representing the record value among the fully printed counterparts and a key milestone toward meeting the objectives for a scalable photovoltaic technology.

Origin of the switchable photocurrent direction in BiFeO3 thin films.

We report external bias driven switchable photocurrent (anodic and cathodic) in 2.3 eV indirect band gap perovskite (BiFeO3) photoactive thin films. Depending on the applied bias our BiFeO3 films exhibit photocurrents more usually found in p- or n-type semiconductor photoelectrodes. In order to understand the anomalous behaviour ambient photoemission spectroscopy and Kelvin-probe techniques have been used to determine the band structure of the BiFeO3. We found that the Fermi level (Ef) is at -4.96 eV (vs. vacuum) with a mid-gap at -4.93 eV (vs. vacuum). Our photochemically determined flat band potential (Efb) was found to be 0.3 V vs. NHE (-4.8 V vs. vacuum). These band positions indicate that Ef is close to mid-gap, and Efb is close to the equilibrium with the electrolyte enabling either cathodic or anodic band bending. We show an ability to control switching from n- to p-type behaviour through the application of external bias to the BiFeO3 thin film. This ability to control majority carrier dynamics at low applied bias opens a number of applications in novel optoelectronic switches, logic and energy conversion devices.

Deep Learning-Assisted Multivariate Analysis for Nanoscale Characterization of Heterogeneous Beam-Sensitive Materials.

Nanoscale materials characterization often uses highly energetic probes which can rapidly damage beam-sensitive materials, such as hybrid organic-inorganic compounds. Reducing the probe dose minimizes the damage, but often at the cost of lower signal-to-noise ratio (SNR) in the acquired data. This work reports the optimization and validation of principal component analysis (PCA) and nonnegative matrix factorization for the postprocessing of low-dose nanoscale characterization data. PCA is found to be the best approach for data denoising. However, the popular scree plot-based method for separation of principal and noise components results in inaccurate or excessively noisy models of the heterogeneous original data, even after Poissonian noise weighting. Manual separation of principal and noise components produces a denoised model which more accurately reproduces physical features present in the raw data while improving SNR by an order of magnitude. However, manual selection is time-consuming and potentially subjective. To suppress these disadvantages, a deep learning-based component classification method is proposed. The neural network model can examine PCA components and automatically classify them with an accuracy of >99% and a rate of ∼2 component/s. Together, multivariate analysis and deep learning enable a deeper analysis of nanoscale materials' characterization, allowing as much information as possible to be extracted.

Controlled Porosity in Ferroelectric BaTiO3 Photoanodes.

The use of ferroelectric polarization to promote electron-hole separation has emerged as a promising strategy to improve photocatalytic activity. Although ferroelectric thin films with planar geometry have been largely studied, nanostructured and porous ferroelectric thin films have not been commonly used in photo-electrocatalysis. The inclusion of porosity in ferroelectric thin films would enhance the surface area and reactivity, leading to a potential improvement of the photoelectrochemical (PEC) performance. Herein, the preparation of porous barium titanate (pBTO) thin films by a soft template-assisted sol-gel method is reported, and the control of porosity using different organic/inorganic ratios is verified by the combination of scanning electron microscopy and ellipsometry techniques. Using piezoresponse force microscopy, the switching of ferroelectric domains in pBTO thin films is observed, confirming that the ferroelectric polarization is still retained in the porous structures. In addition, the presence of porosity in pBTO thin films leads to a clear improvement of the PEC response. By electrochemical poling, we also demonstrated the tuning of the PEC performance of pBTO thin films via ferroelectric polarization. Our work offers a simple and low-cost approach to control the morphology optimization of ferroelectric thin films, which could open up the development of materials with great potential for PEC applications.

Overcoming Nanoscale Inhomogeneities in Thin-Film Perovskites via Exceptional Post-annealing Grain Growth for Enhanced Photodetection.

Antisolvent-assisted spin coating has been widely used for fabricating metal halide perovskite films with smooth and compact morphology. However, localized nanoscale inhomogeneities exist in these films owing to rapid crystallization, undermining their overall optoelectronic performance. Here, we show that by relaxing the requirement for film smoothness, outstanding film quality can be obtained simply through a post-annealing grain growth process without passivation agents. The morphological changes, driven by a vaporized methylammonium chloride (MACl)-dimethylformamide (DMF) solution, lead to comprehensive defect elimination. Our nanoscale characterization visualizes the local defective clusters in the as-deposited film and their elimination following treatment, which couples with the observation of emissive grain boundaries and excellent inter- and intragrain optoelectronic uniformity in the polycrystalline film. Overcoming these performance-limiting inhomogeneities results in the enhancement of the photoresponse to low-light (<0.1 mW cm-2) illumination by up to 40-fold, yielding high-performance photodiodes with superior low-light detection.

Additive-Free, Low-Temperature Crystallization of Stable α-FAPbI3 Perovskite.

Formamidinium lead triiodide (FAPbI3 ) is attractive for photovoltaic devices due to its optimal bandgap at around 1.45 eV and improved thermal stability compared with methylammonium-based perovskites. Crystallization of phase-pure α-FAPbI3 conventionally requires high-temperature thermal annealing at 150 °C whilst the obtained α-FAPbI3 is metastable at room temperature. Here, aerosol-assisted crystallization (AAC) is reported, which converts yellow δ-FAPbI3 into black α-FAPbI3 at only 100 °C using precursor solutions containing only lead iodide and formamidinium iodide with no chemical additives. The obtained α-FAPbI3 exhibits remarkably enhanced stability compared to the 150 °C annealed counterparts, in combination with improvements in film crystallinity and photoluminescence yield. Using X-ray diffraction, X-ray scattering, and density functional theory simulation, it is identified that relaxation of residual tensile strains, achieved through the lower annealing temperature and post-crystallization crystal growth during AAC, is the key factor that facilitates the formation of phase-stable α-FAPbI3 . This overcomes the strain-induced lattice expansion that is known to cause the metastability of α-FAPbI3 . Accordingly, pure FAPbI3 p-i-n solar cells are reported, facilitated by the low-temperature (≤100 °C) AAC processing, which demonstrates increases of both power conversion efficiency and operational stability compared to devices fabricated using 150 °C annealed films.

Determining Out-of-Plane Hole Mobility in CuSCN via the Time-of-Flight Technique To Elucidate Its Function in Perovskite Solar Cells.

Copper(I) thiocyanate (CuSCN) is a stable, low-cost, solution-processable p-type inorganic semiconductor used in numerous optoelectronic applications. Here, for the first time, we employ the time-of-flight (ToF) technique to measure the out-of-plane hole mobility of CuSCN films, enabled by the deposition of 4 µm-thick films using aerosol-assisted chemical vapor deposition (AACVD). A hole mobility of ∼10-3 cm2/V s was measured with a weak electric field dependence of 0.005 cm/V1/2. Additionally, by measuring several 1.5 µm CuSCN films, we show that the mobility is independent of thickness. To further validate the suitability of our AACVD-prepared 1.5 µm-thick CuSCN film in device applications, we demonstrate its incorporation as a hole transport layer (HTL) in methylammonium lead iodide (MAPbI3) perovskite solar cells (PSCs). Our AACVD films result in devices with measured power conversion efficiencies of 10.4%, which compares favorably with devices prepared using spin-coated CuSCN HTLs (12.6%), despite the AACVD HTLs being an order of magnitude thicker than their spin-coated analogues. Improved reproducibility and decreased hysteresis were observed, owing to a combination of excellent film quality, high charge-carrier mobility, and favorable interface energetics. In addition to providing a fundamental insight into charge-carrier mobility in CuSCN, our work highlights the AACVD methodology as a scalable, versatile tool suitable for film deposition for use in optoelectronic devices.

Ammonia Gas Sensor Response of a Vertical Zinc Oxide Nanorod-Gold Junction Diode at Room Temperature.

Conventional metal oxide semiconductor (MOS) gas sensors have been investigated for decades to protect our life and property. However, the traditional devices can hardly fulfill the requirements of our fast developing mobile society, because the high operating temperatures greatly limit their applications in battery-loaded portable systems that can only drive devices with low power consumption. As ammonia is gaining importance in the production and storage of hydrogen, there is an increasing demand for energy-efficient ammonia detectors. Hence, in this work, a Schottky diode resulting from the contact between zinc oxide nanorods and gold is designed to detect gaseous ammonia at room temperature with a power consumption of 625 µW. The Schottky diode gas sensors benefit from the change of barrier height in different gases as well as the catalytic effect of gold nanoparticles. This diode structure, fabricated without expensive interdigitated electrodes and displaying excellent performance at room temperature, provides a novel method to equip mobile devices with MOS gas sensors.

The role of carbon dots - derived underlayer in hematite photoanodes.

Hematite is a promising candidate as photoanode for solar-driven water splitting, with a theoretically predicted maximum solar-to-hydrogen conversion efficiency of ∼16%. However, the interfacial charge transfer and recombination greatly limits its activity for photoelectrochemical water splitting. Carbon dots exhibit great potential in photoelectrochemical water splitting for solar to hydrogen conversion as photosensitisers and co-catalysts. Here we developed a novel carbon underlayer from low-cost and environmental-friendly carbon dots through a facile hydrothermal process, introduced between the fluorine-doped tin oxide conducting substrate and hematite photoanodes. This led to a remarkable enhancement in the photocurrent density. Owing to the triple functional role of carbon dots underlayer in improving the interfacial properties of FTO/hematite and providing carbon source for the overlayer as well as the change in the iron oxidation state, the bulk and interfacial charge transfer dynamics of hematite are significantly enhanced, and consequently led to a remarkable enhancement in the photocurrent density. The results revealed a substantial improvement in the charge transfer rate, yielding a charge transfer efficiency of up to 80% at 1.25 V vs. RHE. In addition, a significant enhancement in the lifetime of photogenerated electrons and an increased carrier density were observed for the hematite photoanodes modified with a carbon underlayer, confirming that the use of sustainable carbon nanomaterials is an effective strategy to boost the photoelectrochemical performance of semiconductors for energy conversion.

Role of Temperature and Growth Period in the Synthesis of Hydrothermally Grown TiO2 Nanorods.

Highly uniformed, surfactant free and vertically oriented titanium-di-oxide (TiO2) nanorods were grown on pre-treated fluorine doped tin oxide (FTO) using hydrothermal method through titanium tetra butoxide (Ti(OBu)4) as titanium source. Three different temperatures 130 °C, 150 °C and 180 °C were followed to grow the nanorods at a fixed reaction time of 4 h. The prepared TiO2 nanorods were annealed at the temperatures of 550 °C and 600 °C for 3 h. X-ray diffraction (XRD) analysis shows that obtained nanorods exhibit pure rutile phase. From scanning electron microscopy (SEM) analysis, it was found that increasing temperature led to decreasing the diameter of the nanorods. In addition to these, formation of hierarchical type TiO2 nanorods was also observed at 130 °C. UV-visible spectra analysis was carried out to find the influence of diameter of the nanorods on its optical properties. The plausible mechanism of the growth process is also discussed.

Unusual Thermal Boundary Resistance in Halide Perovskites: A Way To Tune Ultralow Thermal Conductivity for Thermoelectrics.

Halide perovskites have emerged as promising candidates as the active material in photovoltaics and light-emitting diodes. They possess unusual bulk thermal transport properties that have been the focus of a number of studies, but there is much less understanding of thermal transport in thin films where a diverse range of structures and morphologies are accessible. Here, we report on the tuning of in-plane thermal conductivity in methylammonium lead iodide thin films by morphological control. Using 3-ω measurements, we find that the room temperature thermal conductivity of thermally evaporated methylammonium lead iodide perovskite films ranges from 0.31 to 0.59 W/(m K). We measure a discontinuity in thermal conductivity at the orthorhombic-tetragonal phase transition and explore this using density functional theory and attributing it to a collapse in the phonon group velocity along the c-axis of the tetragonal crystal. Moreover, we have quantified the thermal boundary resistance (Kapitza resistance) for thermally evaporated films, allowing us to estimate the Kapitza length, which is 36 ± 2 nm at room temperature and 15 ± 2 nm at 100 K. Curiously, the Kapitza resistance has a strong temperature dependence which we also explore using density functional theory, with these results suggesting an important role of methylammonium rotational modes in scattering phonons at the crystallite boundaries.

ZnO nanowires for solar cells: a comprehensive review.

As an abundant and non-toxic wide band gap semiconductor with a high electron mobility, ZnO in the form of nanowires (NWs) has emerged as an important electron transporting material in a vast number of nanostructured solar cells. ZnO NWs are grown by low-cost chemical deposition techniques and their integration into solar cells presents, in principle, significant advantages including efficient optical absorption through light trapping phenomena and enhanced charge carrier separation and collection. However, they also raise some significant issues related to the control of the interface properties and to the technological integration. The present review is intended to report a detailed analysis of the state-of-the-art of all types of nanostructured solar cells integrating ZnO NWs, including extremely thin absorber solar cells, quantum dot solar cells, dye-sensitized solar cells, organic and hybrid solar cells, as well as halide perovskite-based solar cells.

Influence of ferroelectric dipole on the photocatalytic activity of heterostructured BaTiO3/a-Fe2O3.

Using BaTiO3 as a model ferroelectric material we investigated the influence of the ferroelectric dipole on the photocatalytic activity of a heterogeneous BaTiO3/α-Fe2O3 photocatalyst. Two distinct BaTiO3 samples were used: BTO and BTO-A. The latter consists more ferroelectric tetragonal phase and thus stronger ferroelectricity. It was found that under identical experimental conditions, the photodecolourisation rate of a target dye using BTO-A/α-Fe2O3 under visible light was 1.3 times that of BTO/α-Fe2O3. Photoelectrochemical and photoluminescence analysis confirmed a more effective charge carrier separation in BTO-A/α-Fe2O3. Considering solely the photoexcitation of α-Fe2O3 in the composite photocatalysts under visible light and the similar microstructures of the two catalysts, we propose that the enhanced decolourisation rate when using BTO-A/α-Fe2O3 is due to the improved charge carrier separation and extended charge carrier lifetime arising from an interaction between the ferroelectric dipole and the carriers in α-Fe2O3. Our results demonstrate a new process to use a ferroelectric dipole to manipulate the charge carrier transport, overcome recombination, and extend the charge carrier lifetime of the surface material in a heterogeneous catalyst system.

Biomass-Derived Nitrogen-Doped Carbon Aerogel Counter Electrodes for Dye Sensitized Solar Cells.

Dye sensitized solar cells have emerged as an attractive alternative to conventional solar cells due to their easy processing and the abundance and low cost of their materials. However, the counter electrode in these cells employs platinum which significantly impacts their cost. Here, we report biomass-derived, nitrogen-doped carbon aerogel as an effective alternative to conventional platinum-based counter electrodes for dye sensitized solar cells. A stable suspension of biomass-derived, nitrogen-doped carbon aerogel was prepared in DMF by using oleylamine as a binder. The nitrogen-doped carbon aerogel electrode was annealed at different temperatures, and its impact on photovoltaic performance is investigated. I-V measurements confirm that the annealing temperature substantially enhances the photovoltaic parameters of these devices; these enhancements are linked to the removal of the organic binders. Electrochemical impedance spectra of the counter electrodes confirm that removal of oleylamine in nitrogen-doped carbon aerogels reduces the series resistance of the resulting electrodes. The power conversion efficiency of the solar cells from optimized nitrogen-doped carbon aerogel exhibited comparable efficiency to that of a cell fabricated using a platinum-based counter electrode. This study demonstrates the potential of biomass-derived carbon aerogels as a cheap and sustainable replacement of platinum in DSSCs.

Light-Addressable Potentiometric Sensors Using ZnO Nanorods as the Sensor Substrate for Bioanalytical Applications.

Light-addressable potentiometric sensors (LAPS) are of great interest in bioimaging applications such as the monitoring of concentrations in microfluidic channels or the investigation of metabolic and signaling events in living cells. By measuring the photocurrents at electrolyte-insulator-semiconductor (EIS) and electrolyte-semiconductor structures, LAPS can produce spatiotemporal images of chemical or biological analytes, electrical potentials and impedance. However, its commercial applications are often restricted by their limited AC photocurrents and resolution of LAPS images. Herein, for the first time, the use of 1D semiconducting oxides in the form of ZnO nanorods for LAPS imaging is explored to solve this issue. A significantly increased AC photocurrent with enhanced image resolution has been achieved based on ZnO nanorods, with a photocurrent of 45.7 ± 0.1 nA at a light intensity of 0.05 mW, a lateral resolution as low as 3.0 µm as demonstrated by images of a PMMA dot on ZnO nanorods and a pH sensitivity of 53 mV/pH. The suitability of the device for bioanalysis and bioimaging was demonstrated by monitoring the degradation of a thin poly(ester amide) film with the enzyme α-chymotrypsin using LAPS. This simple and robust route to fabricate LAPS substrates with excellent performance would provide tremendous opportunities for bioimaging.

Optimization of 3D ZnO brush-like nanorods for dye-sensitized solar cells.

In a dye-sensitized solar cell (DSSC) the amount of adsorbed dye on the photoanode surface is a key factor that must be maximized in order to obtain enhanced DSSC performance. In this study 3D ZnO nanostructures, named brush-like, are demonstrated as alternative photoanodes. In these structures, long ZnO nanorods are covered with a metal-organic precursor, known as a layered-hydroxide zinc salt (LHZS), which is subsequently converted to crystalline ZnO using two-step annealing. The LHZS is able to easily grow on any surface, such as the ZnO nanorod surface, without needing the assistance of a seed-layer. Brush-like structures synthesized using different citrate concentrations in the growth solutions and different annealing conditions are characterized and tested as DSSC photoanodes. The best-performing structure reported in this study was obtained using the highest citrate concentration (1.808 mM) and the lowest temperature annealing condition in an oxidative environment. Conversion efficiency as high as 1.95% was obtained when these brush-like structures were employed as DSSC photoanodes. These results are extremely promising for the implementation of these innovative structures in enhanced DSSCs, as well as in other applications that require the maximization of surface area exposed by ZnO or similar semiconductors, such as gas- or bio-sensing or photocatalysis.

Enhanced Photocatalytic Activity of Heterostructured Ferroelectric BaTiO3/α-Fe2O3 and the Significance of Interface Morphology Control.

We have used a ferroelectric BaTiO3 substrate with a hematite (α-Fe2O3) nanostructured surface to form a heterogeneous BaTiO3/α-Fe2O3 photocatalyst. In this study we show that varying the mass ratio of α-Fe2O3 on BaTiO3 has a significant influence on photoinduced decolorization of rhodamine B under simulated sunlight. The highest photocatalytic activity was obtained for BaTiO3-Fe2O3-0.001M, with the lowest mass ratio of α-Fe2O3 in our study. This catalyst exhibited a 2-fold increase in performance compared to pure BaTiO3 and a 5-fold increase when compared to the higher-surface-area pure α-Fe2O3. The increases in performance become more marked upon scaling for the lower surface area of the heterostructured catalyst. Performance enhancement is associated with improved charge-carrier separation at the interface between the ferroelectric surface, which exhibits ferroelectric polarization, and the hematite. Increasing the mass ratio of hematite increases the thickness of this layer, lowers the number of triple-point locations, and results in reduced performance enhancement. We show that the reduced performance is due to a lack of light penetrating into BaTiO3 and to relationships between the depolarization field from the ferroelectric and carriers in the hematite. Our findings demonstrate that it is possible to use the built-in electric field of a ferroelectric material to promote charge-carrier separation and boost photocatalytic efficiency.

Carbon-Nanodot Solar Cells from Renewable Precursors.

It has recently been shown that waste biomass can be converted into a wide range of functional materials, including those with desirable optical and electronic properties, offering the opportunity to find new uses for these renewable resources. Photovoltaics is one area in which finding the combination of abundant, low-cost and non-toxic materials with the necessary functionality can be challenging. In this paper the performance of carbon nanodots derived from a wide range of biomaterials obtained from different biomass sources as sensitisers for TiO2 -based nanostructured solar cells was compared; polysaccharides (chitosan and chitin), monosaccharide (d-glucose), amino acids (l-arginine and l-cysteine) and raw lobster shells were used to produce carbon nanodots through hydrothermal carbonisation. The highest solar power conversion efficiency (PCE) of 0.36 % was obtained by using l-arginine carbon nanodots as sensitisers, whereas lobster shells, as a model source of chitin from actual food waste, showed a PCE of 0.22 %. By comparing this wide range of materials, the performance of the solar cells was correlated with the materials characteristics by carefully investigating the structural and optical properties of each family of carbon nanodots, and it was shown that the combination of amine and carboxylic acid functionalisation is particularly beneficial for the solar-cell performance.

Dye-Sensitized Solar Cells: The Future of Using Earth-Abundant Elements in Counter Electrodes for Dye-Sensitized Solar Cells (Adv. Mater. 20/2016).

Sustainability is an important concept generating traction in the research community. To be really sustainable the full life cycle of a product needs to be carefully considered. A key aspect of this is using elements that are either readily recycled or accessible in the Earth's biosphere. Jigsawing these materials together in compounds to address our future energy needs represents a great opportunity for the current generation of researchers. On page 3802, S. Dunn and J. Briscoe summarize the performance of a selection of alternative materials to replace platinum in the counter electrodes of dye-sensitized solar cells.