Laboratory calibration and field testing of the Chemcatcher-Metal for trace levels of rare earth elements in estuarine waters.

Little knowledge is available about water concentrations of rare earth elements (REEs) in the marine environment. The direct measurement of REEs in coastal waters is a challenging task due to their ultra-low concentrations as well as the high salt content in the water samples. To quantify these elements at environmental concentrations (pg L(-1) to low ng L(-1)) in coastal waters, current analytical techniques are generally expensive and time consuming, and require complex chemical preconcentration procedures. Therefore, an integrative passive sampler was tested as a more economic alternative sampling approach for REE analysis. We used a Chemcatcher-Metal passive sampler consisting of a 3M Empore Chelating Disk as the receiving phase, as well as a cellulose acetate membrane as the diffusion-limiting layer. The effect of water turbulence and temperature on the uptake rates of REEs was analyzed during 14-day calibration experiments by a flow-through exposure tank system. The sampling rates were in the range of 0.42 mL h(-1) (13 °C; 0.25 m s(-1)) to 4.01 mL h(-1) (13 °C; 1 m s(-1)). Similar results were obtained for the different REEs under investigation. The water turbulence was the most important influence on uptake. The uptake rates were appropriate to ascertain time-weighted average concentrations of REEs during a field experiment in the Elbe Estuary near Cuxhaven Harbor (exposure time 4 weeks). REE concentrations were determined to be in the range 0.2 to 13.8 ng L(-1), where the highest concentrations were found for neodymium and samarium. In comparison, most of the spot samples measured along the Chemcatcher samples had REE concentrations below the limit of detection, in particular due to necessary dilution to minimize the analytical problems that arise with the high salt content in marine water samples. This study was among the first efforts to measure REE levels in the field using a passive sampling approach. Our results suggest that passive samplers could be an effective tool to monitor ultra-trace concentrations of REEs in coastal waters with high salt content.

Absolute quantification of transferrin in blood samples of harbour seals using HPLC-ICP-MS.

Harbour seals (Phoca vitulina) are bio-indicators for the assessment of their habitat and environmental changes. Besides population parameters and trends (survival, age structure, sex ratio), the individual health status represents a further important parameter for this assessment. The health status of seals is a complex and vague term, determined by a wide range of diagnostic parameters. Quantities of important blood proteins such as transferrin (Tf), as well as altered distribution patterns of its glycoforms, are frequently used as biomarkers in clinical diagnosis. Within this context Tf quantities and a varying pattern of its glycoforms are used as indicator for e.g. certain liver diseases, which also represents one of the most frequently observed pathological indication in harbour seals of the North Sea. Currently, most assay based quantification methods for Tf are limited since they often provide only information regarding the total Tf concentration rather than information of its different glycoforms. Due to a lack of suitable seal Tf antibodies also the application of more specific antibody based approaches is not possible. Within this background a new approach for the absolute quantification of the iron-transport protein Tf in the blood of harbour seals using its characteristic iron content and HPLC-ICP-MS detection is described. Method validation was performed using a certified human serum reference material (ERM-DA470K/IFCC). A Tf concentration of 2.33 ± 0.03 g L(-1) (sum of all quantified glycoforms) has been calculated, which is in good agreement with the certified total Tf concentration of 2.35 ± 0.08 g L(-1), confirming the accuracy of the proposed analytical method. Finally, different seal samples were analysed to demonstrate the suitability of the procedure for the quantification of Tf in real samples as well as to observe modified glycoform patterns. Compared to our previous studies for the first time it was possible to quantify the serum Tf baseline reference range for male (1.42-2.35 g L(-1)) and female German North Sea seals (1.93-2.74 g L(-1)) as well as a CDT level of 0.00-0.10 g L(-1), respectively, which provides valuable further diagnostic information regarding the health status of these specific marine mammals. Compared to assay based quantification approaches the proposed technique indicates great potential to obtain comparable and traceable absolute quantitative results, which are in particular important for long term investigations. This absolute quantification is based on an accurate, traceable element standard, while assay based approaches often show variations depending on the kit quality or changing activities of the used antibodies.

Metallomics approach for the identification of the iron transport protein transferrin in the blood of harbour seals (Phoca vitulina).

The health status of marine mammals such as harbour seals (Phoca vitulina) represents an indirect but powerful way for the assessment of environmental changes. The present work illustrates the first investigation and characterisation of Tf isolated from blood samples of North Sea harbour seals with a view to using changes in Tf isoform patterns as an additional parameter in extended studies of their health status. Therefore, an HPLC-ICP-MS approach has been developed which allows the highly resolved separation and fractionation of up to eight different Tf isoforms, as well as their sensitive and specific detection on the basis of their characteristic iron content. Molecule-specific detection techniques such as nanoLC-ESI-QTRAP-MS or MALDI-TOF-MS were used as complementary techniques to unambiguously identify the isolated proteins as Tf via cross species protein identification and to further characterise the molecular weight as well as the sialic acid content, which is responsible for the elution behaviour of the different isoforms during their ion exchange separation. A molecular mass above 80 kDa has been measured for the different seal Tf isoforms, which is in good agreement with the known molecular mass in other mammalian species, while the estimated pI of the different isoforms indicates some differences in comparison to other species. A number of homologies to known Tf sequences have been observed, which finally allows the cross species protein identification. The combined metallomics orientated analytical approach, which includes the complementary application of element and molecule-specific detection techniques, opens up interesting possibilities for the fast and targeted isolation and identification of a diagnostically relevant metal containing protein from an un-sequenced mammalian species prior to its utilisation in extended studies.

Spectroscopic and analytical characteristics of an inductively coupled argon plasma combined with hydride generation with or without simultaneous introduction of the sample aerosol for optical emission spectrometry.

A radially viewed inductively coupled argon plasma was used for optical emission spectrometry of volatile species formed by reaction with NaBH(4) (hydride generation). The volatile hydrides were either introduced into the plasma alone or at the same time as a sample aerosol generated by pneumatic nebulization with a commercially available Concomitant Metals Analyzer. The effects of the forward power, the presence of pre-reducing agents [(NH(2))(2)SC, KI, KBr and hot HCl], the occurrence of easily ionized elements (Ca, K, Mg and Na) in the analyte solutions on the excitation temperature (as measured via Ar atomic lines) and the electron number density were investigated for both of the sample introduction modes applied. The detection limits and the signal-to-background intensity ratios for As, Bi, Sb, Se and Sn lines were also evaluated and were observed to deteriorate with increasing power. When simultaneous hydride generation and pneumatic nebulization was employed under optimized experimental conditions, detection limits of 3.5, 2.9, 4.3, 1.5 and 2.1 microg L(-1) for As, Bi, Sb, Se and Sn, respectively, were obtained, and the intensities of the analytical lines for elements that do not form volatile hydrides were found to be 40% (Cd), 30% (Ni), 20% (Co, Cr, Fe, Mn and Zn) and 10% (Cu, Mg, V) greater than those obtained when only pneumatic nebulization was used.

Investigation of the nucleation and growth dynamics of FePt nanoparticles prepared via a high-temperature synthesis route employing PtCl(2) as platinum precursor.

A high-temperature synthesis for FePt nanoparticles using Fe(acac)(3) and PtCl(2) as a less reactive platinum precursor than the commonly used Pt(acac)(2) is investigated. The use of this precursor allows the synthesis of larger particles. Kinetic studies demonstrate a single nucleation event at the beginning of the reaction and a growth via consumption of monomers. Ostwald ripening does not occur under the investigated reaction conditions. A novel method for a further increase of particle sizes based on continuous injection of additional monomers during the growth regime is presented.

Side effects of a non-peroxide-based home bleaching agent on dental enamel.

Changes in the chemistry and structure of enamel due to a non-peroxide-based home bleaching product (Rapid White) were studied in vitro using attenuated total reflectance-infrared spectroscopy, Raman spectroscopy, electron probe microanalysis, flame atomic absorption spectroscopy, and total reflection X-ray fluorescence. The results revealed that the citric-acid-containing gel-like component of the bleaching system substantially impacts on the dental hard tissue. Enamel is affected on several levels: (i) the organic component is removed from superficial and deeper enamel layers and remnants of the bleaching gel are embedded in the emptied voids; (ii) cracks and chemical inhomogeneities with respect to Ca and P occur on the surface; and (iii) within a submicron layer of enamel, the Ca-O bond strength in apatite decreases, thus enhancing calcium leakage from the bleached enamel hard tissue.

Evaluation and application of argon and helium microstrip plasma for the determination of mercury by the cold vapor technique and optical emission spectrometry.

The suitability of a 2.45-GHz atmospheric pressure, low-power microwave microstrip plasma (MSP) operated with Ar and He for the determination of Hg by continuous-flow cold vapor (CV) generation, using SnCl2/HCl as the reducing agent, and optical emission spectrometry (OES) using a small CCD spectrometer was studied. The areas of stability for a discharge in the Ar and in the He MSP enclosed in a cylindrical channel in a quartz wafer were investigated. The excitation temperatures as measured for discharge gas atoms (Ar I, He I), and the electron number densities at 35-40 W and 15-400 mL min(-1) were found to be at the order of 3,200-5,500 K and 0.8x10(14)-1.6x10(14) cm(-3), respectively. The relative intensity of the Hg I 253.6-nm line and the signal-to-background ratio as a function of the forward power (35-40 W) as well as of the flow rate of the working gas (15-400 mL min(-1)) were evaluated and discussed. For the selected measurement conditions, the Ar MSP was established to have the lower detection limit for Hg (0.6 ng mL(-1)) compared with the He MSP. The linearity range is up to 300 ng mL(-1) and the precision is on the order of 1-3%. With the optimized CV Ar MSP-OES method a determination of Hg in spiked domestic and natural waters at concentration levels of 20-100 microg L(-1) and an accuracy of 1-4% could be performed. In an NIST domestic sludge standard reference material, Hg (3.64 microg g(-1)) could be determined with a relative standard deviation of 4% and an agreement better than 4%.

Structural characterization of beta-sheeted oligomers formed on the pathway of oxidative prion protein aggregation in vitro.

The pathology of transmissible spongiform encephalopathies (TSEs) is strongly associated with the structural conversion of the cellular prion protein (PrPC) into a misfolded isoform (PrPSc) that assembles into amyloid fibrils. Since increased levels of oxidative stress have been linked to prion diseases, we investigated the metal-induced oxidation of human PrP (90-231). A novel in vitro conversion assay based on aerobic incubation of PrP in the presence of elemental copper pellets at pH 5 was established, resulting in aggregation of highly beta-sheeted prion proteins. We show for the first time that two discrete oligomeric species of elongated shape, approx. 25 mers and 100 mers, are formed on the pathway of oxidative PrP aggregation in vitro, which are well characterized regarding shape and size using small-angle X-ray scattering (SAXS), dynamic light scattering (DLS), and electron microscopy (EM). Considering that small oligomers of highly similar size have recently been reported to show the highest specific infectivity within TSE-infected brain tissues of hamsters, the novel oligomers observed in this study are interesting candidates as agent causing neurodegenerative and/or self-propagating effects. Moreover, our results significantly strengthen the theory that oxidative stress might be an influence that leads to substantial structural conversions of PrP in vivo.

Direct analysis of Al2O3 powders by total reflection X-ray fluorescence spectrometry.

A direct analysis procedure for the determination of trace impurities of Ca, V, Cr, Mn, Fe, Ni, Cu, Zn and Ga in Al2O3 ceramic powders by total reflection X-ray fluorescence spectrometry (TXRF) is described. The powders were analysed in the form of slurries containing 1-10 mg mL(-1) of powder. The use of the procedure in the case of powders with differing grain size and for different slurry concentrations was investigated. Three different quantification possibilities were compared, namely the use of Al as a matrix component, the use of Fe as a trace element contained in the sample or of Co added in concentrations of 200 microg g(-1) as internal standard. The homogeneity of elemental distributions in sample layers deposited on the TXRF quartz carriers by evaporating 5 microL of the 10 mg mL(-1) slurries was studied by scanning the 4- to 5-mm-diameter spots of two samples by synchrotron radiation TXRF at Hasylab. For powders with differing graininess but mainly finer than about a few 10 microm, no systematic influence of the grain size on the accuracy of the determinations of Ca, V, Fe, Ni, Cu and Zn could be observed. The measurement precision, however, seemed to be limited by inhomogeneous distributions of the trace elements in the samples as testified by the synchrotron radiation TXRF scans. Detection limits of the developed TXRF procedure for Ca, V, Cr, Mn, Fe, Ni, Cu, Zn and Ga were found to be in the 0.3-7 microg g(-1) range and were shown to increase slightly with the grain size of the samples. Quantification using Al (matrix) as internal standard led to systematically higher values out of the accuracy required, whereas the other two approaches in all cases led to reliable results.

Some trends in the development of microplasmas for spectrochemical analysis.

The development of microplasmas for spectrochemical analysis by optical methods is discussed. Recent achievements in miniaturization are highlighted, especially for three types of plasmas, namely high-frequency plasmas, dc-discharges and microwave plasmas. The potentials of each of these groups of plasmas as sources for atomic emission spectrometry are discussed. Literature citations and experiments indicate that the plasmas are also very useful as atom reservoirs for atomic absorption spectrometry. Methods of sampling, including feeding with gas chromatography effluents, the use of electrothermal vaporization, and the evolution of gaseous species (as shown for the case of Hg vapor), are discussed as prominent interfaces to make use of these sources for elemental analysis.

Nonaqueous capillary electrophoresis with indirect electrochemical detection.

Nonaqueous capillary electrophoresis (NACE) which makes use of organic solvents in place of conventional aqueous electrophoresis buffers is gaining increasing importance among modern separation techniques. Recently, it has been shown that amperometric detection in conjunction with acetonitrile-based NACE offers an extended accessible potential range and an enhanced long-term stability of the amperometric responses generated at solid electrodes. The present contribution takes advantage of the latter aspect to develop reliable systems for NACE with indirect electrochemical detection (IED). In this context, several compounds such as (ferrocenylmethyl)trimethylammonium perchlorate, tris(1,10-phenanthroline)cobalt(III) perchlorate and bis(1,4,7-triazacyclononane)nickel(II) perchlorate were studied regarding their suitability to act as electroactive buffer additives for IED in NACE. The performance characteristics for the respective buffer systems were evaluated. Tetraalkylammonium perchlorates served as model compounds for the optimization of the NACE-IED system. Target analytes choline and acetylcholine could easily be separated and determined by means of NACE-IED. In the case of a buffer system containing 10(-4) M tris(1,10-phenanthroline)cobalt(III) perchlorate the limits of detection were 2.5 x 10(-7) M and 4.6 x 10(-7) M for choline and acetylcholine, respectively. With the elaborated analytical procedure choline could be determined in pharmaceutical preparations.