Finite element modelling of stapled colorectal end-to-end anastomosis: advantages of variable height stapler design.

The impact of surgical staplers on tissues has been studied mostly in an empirical manner. In this paper, finite element method was used to clarify the mechanics of tissue stapling and associated phenomena. Various stapling modalities and several designs of circular staplers were investigated to evaluate the impact of the device on tissues and mechanical performance of the end-to-end colorectal anastomosis. Numerical simulations demonstrated that a single row of staples is not adequate to resist leakage due to non-linear buckling and opening of the tissue layers between two adjacent staples. Compared to the single staple row configuration, significant increase in stress experienced by the tissue at the inner staple rows was observed in two and three rows designs. On the other hand, adding second and/or third staple row had no effect on strain in the tissue inside the staples. Variable height design with higher staples in outer rows significantly reduced the stresses and strains in outer rows when compared to the same configuration with flat cartridge.

Mechanical evaluation of a tapered thread-run-out half-pin designed for external skeletal fixation in small animals.

An in vitro mechanical study was performed to compare the stiffness, maximum load, and cyclic load-to-failure of a new external fixation half-pin design utilizing a tapered thread-run-out (TRO) feature with currently available positive profile thread (PP) half-pins. Five different sizes of each of the two pin types were evaluated. Under static loading, TRO pins were significantly stiffer and had a higher maximum load compared to the similar sized PP pins (p <0.0001 for all comparisons). In cyclic fatigue testing, TRO pins lasted 2.3- to 4.9-fold more cycles than PP pins of similar size (p <0.0001 for all comparisons). The increased pin stiffness and improved cyclic lifespan provided by TRO pins may be especially valuable in the stabilization of biologically and mechanically challenging fracture cases where healing is prolonged.

Bone material ultrasound velocity is predictive of whole bone strength.

In humans, bone strength is assessed indirectly by the noninvasive measurement of structure or mass. Recent clinical application of an ultrasonic critical-angle reflectometry technique (UCR) has demonstrated the measurement of the regional and directional distribution of mechanical stiffness. This study investigates the specific question: are these measurements of a local material level property predictive of the strength of whole bone? Maximum values of pressure wave velocity and breaking strength were recorded at two locations (midshaft and base of neck) on rat femurs from growing rats. The results demonstrate a strong empirical relationship between material-level ultrasound (US) velocity and whole bone mechanical strength. However, the US velocity at a specific bone site can be used to assess bone strength at that site only, explaining discrepancies in other published studies that negate a relationship between strength and US velocity. The results indicate an important role for US velocity measurement in clinical evaluation of bone health.

Axial characteristics of circular external skeletal fixator single ring constructs.

OBJECTIVE: Evaluate the effects of varying ring diameter, wire tension, and wire-divergence angle on the axial stiffness characteristics of circular external skeletal fixator single-ring constructs. Study Design-Biomechanical evaluation using circular fixator components and a Delrin cylinder bone model. METHODS: Single ring constructs using two 1.6 mm diameter Kirschner wires to secure a 19 mm Delrin cylinder centered within the ring were examined. Component variables evaluated were ring diameter (50 mm, 66 mm, 84 mm, and 118 mm), wire-divergence angle (30 degrees, 60 degrees, and 90 degrees ), and wire tension (0 kg, 30 kg, 60 kg, and 90 kg). A total of 48 constructs were examined. Rings were rigidly mounted on a universal testing system and the cylinder loaded in axial compression (7.4 N/s) to 220 N. Load/displacement curves were analyzed to determine the following: the displacement (mm) that occurred before the slope of each load/displacement curve became linear, the stiffness (N/mm) of the linear portion of each load/deformation curve, and the total displacement (mm) produced at maximal load. Least-squares linear regression was used to model response variables as linear functions of ring diameter, wire divergence angle, and wire tension. Three-way interactions and 2-way interactions among independent component variables were evaluated first in the modeling process and included in a best model if response variables were found to have statistically significant regression coefficients. The regression coefficients and corresponding standard errors and covariances were used to estimate the maximal effect and standard error attributable to wire divergency angle (change from 30 degrees to 90 degrees ) and wire tension (change from 0 to 90 kg) for each ring diameter. RESULTS: All load/deformation curves had an initial exponential increase in stiffness, with the slope becoming linear at higher loads. The exponential phase was more pronounced in larger-diameter ring constructs and was mitigated by tensioning the wires. Ring diameter had the greatest influence on displacement that occurred before the curve became linear (semipartial r(2) [sp-r2] = .89), stiffness (sp-r2 = .94), and total displacement (sp-r2 = .93). Wire tension exerted a smaller influence on displacement that occurred before the curve became linear (sp-r2 =.06), stiffness (sp-r2 = .03), and total displacement (sp-r2 = .05). Wire divergence angle had a nominal effect on displacement that occurred before the curve became linear (sp-r2 = .0001), on stiffness (sp-r2 = .004), and on total displacement (sp-r2 =.003). CONCLUSIONS: Ring diameter had a profound effect on the axial stiffness characteristic of single ring constructs. Tensioning of the fixation wires can improve the axial stiffness characteristics of these constructs, particularly in larger diameter ring constructs, by mitigating the initial exponential phase of the load/deformation curve. Wire divergence angle had only a nominal differential effect on axial stability. CLINICAL RELEVANCE: Understanding how individual component variables and their interactions influence bone segment stability should help surgeons to optimize interfragmentary strain. Tensioning fixation wires is probably unnecessary in 50 mm diameter ring constructs, but assumes greater importance as ring diameter increases.

A biomechanical comparison of open and thoracoscopic anterior spinal release in a goat model.

STUDY DESIGN: A biomechanical assessment of anterior release and discectomy in the thoracic spine was performed on an animal model using thoracoscopic and open thoracotomy techniques. OBJECTIVES: To compare the relative efficacy of these two techniques of release in achieving increased spinal mobility. BACKGROUND DATA: The clinical use of video-assisted thoracoscopy in the correction of spinal deformity is increasing. The effectiveness of thoracoscopic anterior spinal release with discectomy has not been evaluated biomechanically. METHODS: Anterior release with discectomy was performed on six midthoracic motion segments in five mature goats. The thoracoscopic technique was used for three levels on one side, and an open thoracotomy was used for the alternating three levels of the contralateral side. The duration of surgery for disc excision and the amount of blood loss for each technique were recorded. The intact cranial and caudal motion segments served as controls. The motion segments were individually subjected to nondestructive biomechanical testing. Torsional, sagittal, and coronal bending torques were applied, and the resulting angular displacement was measured. RESULTS: The duration of surgery to remove a disc thoracoscopically decreased as experience was gained by the surgeon. The amount of intraoperative blood loss was comparable using the two methods. There was significantly increased flexibility in the released segments with both techniques, compared with the flexibility in the intact levels for all three loading directions. There was no difference in the motion obtained after release between the two techniques. CONCLUSION: Open and thoracoscopic anterior release and discectomy have been demonstrated, through biomechanical in vitro testing, to increase the flexibility of the spine to a similar extent.

In vitro comparison of the standard short limb cast and three configurations of short limb transfixation casts in equine forelimbs.

Axial stability of equine oblique proximal phalangeal osteotomies with application of the standard short limb cast or 1 of 3 configurations of transfixation casts was determined in vitro. Transfixation cast methods included use of parallel pins, divergent pins, or parallel pins incorporating a metal walking bar. Displacement at the osteotomy was recorded for each limb at 4,448 N. Standard short limb casts provided significantly (P = 0.0002) less axial stability than did any form of transfixation cast. Significant differences were not found between the 3 transfixation casts.