Study on the mechanism of methane "solid-liquid-gas" conversion controlled by the evolution of coal micro- and nanopore structure.

Currently, the utilization of coalbed methane resources in the Guizhou region faces challenges such as complex reservoir structure, high gas content, and microporous development. Based on these, the pore structure and adsorption capacity of Guizhou tectonic deformed coals (TDCs) were evaluated using a suite of integrated diagnostic techniques including low-temperature nitrogen adsorption (LT-N2A), mercury intrusion porosimetry (MIP), methane isothermal adsorption. Through the above methods, the pore structure and adsorption characteristics of the samples were characterized; The samples were divided into the range of joint pores by combining the results of MIP and LT-N2A; Using the molecular simulation software, the 2 nm, 4 nm, 10 nm pores affecting the methane endowment state were investigated respectively, and from the perspective of the heat of adsorption and energy, the concept of the three-phase transition of methane was proposed, and explore the change of the pore spacing affecting the endowment state of methane from the solid state pore to the gas state pore. The results provide new ideas for the in-depth study of gas storage in tectonic coal reservoirs in Guizhou Province.

Intraoperative Intraocular Lens Waste: Incidence, Cost and Reasons.

PURPOSE: To evaluate the incidence and cost of intraocular lens(IOL) waste during IOL implantation, as well as the reasons for it. METHODS: A retrospective analysis was conducted on the data of 485 patients from the IOL waste registers of a single tertiary eye hospital in China during 2016-2020. The primary outcomes were the incidence, cost, and reasons for different IOL properties. Cases were examined to ascertain IOL material, design, procedural details, and causes of waste. RESULTS: IOL waste occurred in 485 (6.62‰) of the 73,246 IOL implantations during the study period. The total cost of IOL waste was 429, 850.26 Chinese Yuan (CNY) related to waste with an average cost of 2, 442.33 CNY per procedure during the study period. Comparisons between IOL properties showed that polymethyl methacrylate (PMMA) material (39, 2.05%), three-piece design (142, 1.49%), and secondary IOL implantation (26, 2.16%) were associated with IOL wastage, and the difference was statistically significant. The causes of IOL waste were damage (107, 60.80%), patient reasons (37, 21.26%), aseptic errors (22, 12.50%), IOL quality problems (8, 4.55%), and loss (2, 1.14%). CONCLUSIONS: The incidence of IOL waste is low, but still leads to a significant cost burden due to a large number of cataract surgeries. PMMA material, three-piece design, and secondary implantation were identified as factors increasing IOL waste. Damage emerged as the primary reason for waste, largely attributed to human error. Therefore, the development of strategies to mitigate IOL waste is imperative.

High-quality coherent ghost imaging of a transmission target.

When the test detector of ghost imaging (GI) is a point-like detector and the detector's transverse size is smaller than the transverse coherence length of the light field at the detection plane, this case is corresponding to coherent GI (CGI) and the imaging result recovered by traditional GI (TGI) reconstruction algorithm is usually bad for a transmission target. Here a CGI scheme of a transmission target is proposed and a corresponding CGI reconstruction algorithm is developed to stably recover the target's image. The validity of the proposed method is verified by both simulation and experiments. Both the simulation and experimental results demonstrate that the target's transmission function can be perfectly reconstructed by CGI. We also show that the imaging quality of CGI with a point-like detector is better than that of TGI with a bucket detector if detection noise exists in the sampling process. Performance comparisons between CGI reconstruction and TGI reconstruction are also discussed.

Experimental research on the influence of acid on the chemical and pore structure evolution characteristics of Wenjiaba tectonic coal.

The chemical and pore structures of coal play a crucial role in determining the content of free gas in coal reservoirs. This study focuses on investigating the impact of acidification transformation on the micro-physical and chemical structure characteristics of coal samples collected from Wenjiaba No. 1 Mine in Guizhou. The research involves a semi-quantitative analysis of the chemical structure parameters and crystal structure of coal samples before and after acidification using Fourier Transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) experiments. Additionally, the evolution characteristics of the pore structure are characterized through high-pressure mercury injection (HP-MIP), low-temperature nitrogen adsorption (LT-N2A), and scanning electron microscopy (SEM). The experimental findings reveal that the acid solution modifies the structural features of coal samples, weakening certain vibrational structures and altering the chemical composition. Specifically, the asymmetric vibration structure of aliphatic CH2, the asymmetric vibration of aliphatic CH3, and the symmetric vibration of CH2 are affected. This leads to a decrease in the contents of -OH and -NH functional groups while increasing aromatic structures. The crystal structure of coal samples primarily dissolves transversely after acidification, affecting intergranular spacing and average height. Acid treatment corrodes mineral particles within coal sample cracks, augmenting porosity, average pore diameter, and the ratio of macro-pores to transitional pores. Moreover, acidification increases fracture width and texture, enhancing the connectivity of the fracture structure in coal samples. These findings provide theoretical insights for optimizing coalbed methane (CBM) extraction and gas control strategies.

Acidification-Induced Micronano Mechanical Properties and Microscopic Permeability Enhancement Mechanism of Coal.

An acid solution improves the pore-plugging problem in hydraulic fracturing, which in turn improves the permeability of the coal seam. The study aimed to investigate the effect of mixed acid on the micronano mechanical properties and permeability of the coal seam. The surface morphology of acidified coal was analyzed from the micronano scale using atomic force microscopy (AFM) and scanning electron microscopy. Additionally, the micronano scale mechanical characteristics of acidified coal were examined using the mechanical mode in an atomic force microscope. Furthermore, the complexity and connectivity of the micronano pores of samples were investigated using the low-temperature nitrogen adsorption and mercury intrusion porosimetry methods and the fractal theory. The results indicated that the surface minerals of acidified coal were dissolved, loosening the coal and increasing the complexity of the pore structure. Mineral deformation and pore deformation weakened the mechanical properties of coal at the micronano scale, and the mean elastic modulus of acidified coal (B# and E#) decreased by 28.78 and 25.66% compared to that of raw coal. The acid solution effectively enlarged the pore diameter, transitioning from micropores to mesopores and macropores, and the total pore volume of acidified coal increased by 1.88 times and 1.25 times, Kn increased from 0.064 to 0.581 and 0.37, respectively. The type of methane diffusion in the diffusion pores changed from Knudsen diffusion to transition-type diffusion. The tortuosity of the pore structure of acidified coal decreased, the fractal dimension of the tortuosity of the pore structure decreased, and the permeability increased by nearly three times. The research results indicate that the mechanical properties of coal decrease after acidification and that the microstructural changes can promote methane migration (diffusion-seepage), which can provide theoretical guidance for coalbed methane extraction in low-permeability coal reservoirs.

Tailored chitosan/glycerol micropatterned composite dressings by 3D printing for improved wound healing.

Wound infection control is a primary clinical concern nowadays. Various innovative solutions have been developed to fabricate adaptable wound dressings with better control of infected wound healing. This work presents a facile approach by leveraging 3D printing to fabricate chitosan/glycerol into composite dressings with tailored micropatterns to improve wound healing. The bioinks of chitosan/glycerol were investigated as suitable for 3D printing. Then, three tailored micropatterns (i.e., sheet, strip, and mesh) with precise geometry control were 3D printed onto a commercial dressing to fabricate the micropatterned composite dressings. In vitro and in vivo studies indicate that these micropatterned dressings could speed up wound healing due to their increased water uptake capacity (up to ca. 16-fold@2 min), benign cytotoxicity (76.7 % to 90.4 % of cell viability), minor hemolytic activity (<1 %), faster blood coagulation effects (within 76.3 s), low blood coagulation index (14.5 % to 18.7 % @ 6 min), enhanced antibacterial properties (81.0 % to 86.1 % against S. aureus, 83.7 % to 96.5 % against E. coli), and effective inhibition of wound inflammation factors of IL-1ß and TNF-α. Such tailored micropatterned composite dressing is facile to obtain, highly reproducible, and cost-efficient, making it a promising implication for improved and personalized contaminated wound healing.

Determination of polyfluoroalkyl substances in cosmetic products using dispersed liquid-liquid extraction coupled with UHPLC-MS/MS.

Human exposure to polyfluoroalkyl substances (PFASs) via cosmetics has been of increasing concern due to the tremendous detrimental health impacts of PFASs. Developing an effective method for extracting and determining PFASs in cosmetics is crucial in accurately assessing their corresponding human exposure risk. Herein, this study developed a new sample pre-treatment method to address the challenges posed by the variety and complexity of cosmetic matrices. Seventeen PFASs in cosmetic products, including 9 perfluoro carboxylic acids and 8 perfluorosulfonic acids, were simultaneously determined using ultra-high-performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS). The whole pre-treatment process can be divided into three steps. In step 1, cosmetics with diverse matrix types can be effectively dispersed during extraction by using saturated sodium chloride-acetonitrile and saturated sodium chloride-tetrahydrofuran as extraction solvents. In step 2, the pre-purification step employs a potassium ferrocyanide-zinc acetate co-precipitant to remove high molecular weight interferents from the extraction solution, thereby enhancing the efficiency of solid-phase extraction (SPE). In step 3, WAX-SPE is utilized to further eliminate interferents from the extraction solution while concentrating the analytes, meeting the trace analysis requirements for PFASs in cosmetics. The method detection limits were 0.09-0.26 ng g-1. The recoveries ranged from 70.1% to 114.7%, with relative standard deviations in the range of 2.0-19.1%. The method was applied to cosmetic samples in the Guangzhou market, and the total concentration of PFASs ranged from 0 to 10.8 ng g-1. This method has strong anti-interference ability, good applicability, high sensitivity, and good reproducibility, making it suitable for the analysis and detection of perfluorinated acids in cosmetic samples. It provides technical support for cosmetics safety regulation.

The geological factors affecting gas content and permeability of coal seam and reservoir characteristics in Wenjiaba block, Guizhou province.

The gas content and permeability of coal reservoirs are the main factors affecting the productivity of coalbed methane. To explore the law of gas content and permeability of coal reservoirs in the Zhijin area of Guizhou, taking No.16, No.27 and No.30 coal seams in Wenjiaba mining area of Guizhou as the engineering background, based on the relevant data of coalbed methane exploration in Wenjiaba block, the geological structure, coal seam thickness, coal quality characteristics,coal seam gas content and permeability of the area were studied utilizing geological exploration, analysis of coal components and methane adsorption test. The results show that the average thickness of coal seams in this area is between 1.32 and 1.85 m; the average buried depth of the coal seam is in the range of 301.3-384.2 m; the gas content of No.16 and No.27 coal seams is higher in the syncline core. The gas content of the No.30 coal seam forms a gas-rich center in the south of the mining area. The buried depth and gas content of coal seams in the study area show a strong positive correlation. Under the same pressure conditions, the adsorption capacity of dry ash-free basis is significantly higher than that of air-dried coal. The permeability decreases exponentially with the horizontal maximum principal stress and the horizontal minimum principal stress. The horizontal maximum primary stress and the flat minimum prominent stress increase with the increase of the buried depth of the coal seam. The permeability and coal seam burial depth decrease exponentially. This work can provide engineering reference and theoretical support for selecting high-yield target areas for CBM enrichment in the block.

Char dominates black carbon aerosol emission and its historic reduction in China.

Emission factors and inventories of black carbon (BC) aerosols are crucial for estimating their adverse atmospheric effect. However, it is imperative to separate BC emissions into char and soot subgroups due to their significantly different physicochemical properties and potential effects. Here, we present a substantial dataset of char and soot emission factors derived from field and laboratory measurements. Based on the latest results of the char-to-soot ratio, we further reconstructed the emission inventories of char and soot for the years 1960-2017 in China. Our findings indicate that char dominates annual BC emissions and its huge historical reduction, which can be attributable to the rapid changes in energy structure, combustion technology and emission standards in recent decades. Our results suggest that further BC emission reductions in both China and the world should focus on char, which mainly derives from lower-temperature combustion and is easier to decrease compared to soot.

Aqueous-Phase Reactions of Anthropogenic Emissions Lead to the High Chemodiversity of Atmospheric Nitrogen-Containing Compounds during the Haze Event.

Nitrogen-containing organic compounds (NOCs), a type of important reactive-nitrogen species, are abundant in organic aerosols in haze events observed in Northern China. However, due to the complex nature of NOCs, the sources, formation, and influencing factors are still ambiguous. Here, the molecular composition of organic matters (OMs) in hourly PM2.5 samples collected during a haze event in Northern China was characterized using Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS). We found that CHON compounds (formulas containing C, H, O, and N atoms) dominated the OM fractions during the haze and showed high chemodiversity and transformability. Relying on the newly developed revised-workflow and oxidation-hydrolyzation knowledge for CHON compounds, 64% of the major aromatic CHON compounds (>80%) could be derived from the oxidization or hydrolyzation processes. Results from FT-ICR MS data analysis further showed that the aerosol liquid water (ALW)-involved aqueous-phase reactions are important for the molecular distribution of aromatic-CHON compounds besides the coal combustion, and the ALW-involved aromatic-CHON compound formation during daytime and nighttime was different. Our results improve the understanding of molecular composition, sources, and potential formation of CHON compounds, which can help to advance the understanding for the formation, evolution, and control of haze.

Concentrations and biomagnification of persistent organic pollutants in three granivorous food chains from an abandoned e-waste recycling site.

The distinct accumulation patterns of persistent organic pollutants (POPs) among granivorous groups and the biomagnification of POPs from crops to granivorous species are still unclear. In this study, occurrence and biomagnification of POPs in three granivorous species including spotted dove (Spilopelia chinensis), scaly-breasted munia (Lonchura punctulata), and reed vole (Microtus fortis Buechner) from a former e-waste recycling site were investigated. Concentrations of polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (PBDEs) in granivorous species ranged from 41.5 to 1370 and 21.1 to 3890 ng/g lipid weight, respectively. PCBs and PBDEs were the main POPs in birds and vole, while decabromodiphenyl ethane (DBDPE) and PBDEs were predominant POPs in crops. The dominance of BDE 209 was observed in samples, with few exceptions. Biomagnification factors (BMFs) of POPs in birds and vole were measured. BMFs of most POPs in vole were higher than those in birds, indicating that POPs had greater biomagnification potential in vole. Species-specific biomagnification of POPs might be affected by many factors, such as physiochemical properties and metabolic capability of POPs. There was significant correlation between concentration ratios of POPs in muscle/air and log KOA, which demonstrated that respiratory elimination to air affects biomagnification of POPs in granivorous birds and vole.

Interspecific competitive effects and annual differences in predation of Empoasca onukii (Hemiptera: Cicadellidae) by wandering spiders.

Empoasca onukii Matsuda is an important pest widely distributed in tea areas in China, which greatly affects tea production and quality. The long-term use of chemical control measures will cause environmental pollution. To better utilize wandering spiders that have strong competitive effects on the predation of E. onukii, we conducted a path analysis between the populations of E. onukii and wandering spiders in 3 tea plantations in 2020 and 2021. The wandering spider species that had the greatest direct and indirect effects on the population of E. onukii were analyzed by the magnitude of the path coefficient. Then, a gray system analysis was conducted to determine the closeness of the populations of different wandering spiders to E. onukii by the magnitude of gray correlation coefficient. Finally, the competition coefficients were calculated to determine the competitiveness of wandering spiders. In addition, considering the influence of the number of E. onukii on the interspecific competition of wandering spiders, the gray correlation coefficient and competition coefficient were combined to derive the competition intensity index, which was used to analyze the competitiveness of wandering spiders in a comprehensive manner. The highest competition coefficients in 2020 and 2021 were found for Ebrechtella tricuspidata Fabricius (Araneae: Thomisidae) (X2, 0.5329) and Clubiona reichlini Fabricius (Araneae: Clubionidae) (X4, 0.8475), respectively. The magnitude of the competition intensity index showed that the most competitive wandering spider in 2020 and 2021 was E. tricuspidata (X2, 0.5692) and C. reichlini (X4, 0.8892), respectively. The least competitive spider in both years was Plexippus setipes Karsch (Araneae: Salticidae) (X7). The more competitive the wandering spider is, the closer it is to E. onukii in terms of numbers, and the more dominant it is in feeding on E. onukii. By reasonably protecting and utilizing the competitive E. tricuspidata (X2) and C. reichlini (X4), we can achieve sustainable and effective control of E. onukii.

N-N-Bridged Polynuclear POM-Based Coordination Polymers Based on a V-Type Ligand: Proton Conduction and Magnetism.

The construction of polyoxometalate (POM)-based coordination polymers, in the presence of a nitrogen heterocyclic ligand, is intriguing due to the potential for obtaining diverse structures. These structures exhibit extensive application possibilities in the fields of proton conductivity and magnetism. Herein, four new POM-based polynuclear coordination polymers with the formulas of {[Fe2(btb)3(H2O)2(SiW12O40)]·3H2O}n (1), {[Cd2(btb)2(H2O)6(HPMoVI10MoV2O40)]·2H2O}n (2), {[Co3(OH)2(btb)2(H2O)5(HPMoVI10MoV2O40)]·7H2O}n (3), and {[Cu3(OH)(btb)2(H2O)(HP2Mo5O23)]·6H2O}n (4) have been prepared using the V-type 1,3-bis(4H-1,2,4-triazole-4-yl)benzene (btb) ligand. Compounds 1 and 2 feature similar two-dimensional (2D) structures, derived from the binuclear Fe2N6 and Cd2N4 subunits connected by tridentate btb ligands. Meanwhile, in compound 3, hexanuclear Co6(OH)4 units are bound by quadridentate btb ligands forming a 2D layer with the same 4-c sql topology simplification as compounds 1 and 2. In compound 1, Keggin-type polyoxoanions are monodentate-coordinated to metal ions and suspended on the 2D structure, while, in compounds 2 and 3, they act as discrete counterions residing in the interstitial spaces between two adjacent layers, thereby extending the 2D structures into 3D structures through hydrogen bonding interactions. In compound 4, trinuclear Cu3(OH) subunits are further constructed into a 3D framework through cooperation with four tridentate and quadridentate btb ligands as well as Strandberg-type anions. Furthermore, the proton conduction of the four compounds has been investigated. They display high proton conductivities at 358 K and 98% RH with powdered samples, which are 1.26 × 10-3, 1.24 × 10-3, 3.24 × 10-4, and 2.57 × 10-4 S cm-1, respectively. Interestingly, by mixing with Nafion, the composite membranes of compounds 2 and 4 exhibit enhanced proton conductivities, measuring at 4.87 × 10-2 and 1.28 × 10-2 S cm-1, respectively, at 358 K and 98% RH, which suggests excellent potential for applications. In addition, compounds 1, 3, and 4 display antiferromagnetic behaviors due to similar magnetic interactions. This work can provide research insights into the assembly of 2D POM-based coordination polymers with nitrogen heterocyclic ligands and Keggin-type POMs and further promote their research progress in proton conduction.

Influences of Evolution of Pore Structures in Tectonic Coal under Acidization on Methane Desorption.

Experiments on corrosion reactions of pulverized coal with monomeric and polymeric (mixed) acid solutions reveal that monomeric acids are listed in a descending order as HF, HCl, and CH3COOH according to their corrosion effects on tectonic coal collected in Faer Coal Mine (Liupanshui City, Guizhou Province, China). In addition, the optimal mixing ratio of mixed acids is 6% HCl + 6% HF + 3% CH3COOH + 2% KCl. The mineral grains filled in pores in coal samples treated with mixed acid solutions are dissolved, so the porosity increases. The volumes of transition pores and mesopores are obviously affected by acidization, and some transition pores are transformed into mesopores and macropores to form dissolved pores. At the same time, inkbottle-shaped pores reduce, while slit pores or open pores increase. The coal samples after acidization show a higher aromatization degree and an increased relative content of oxygen-containing functional groups, with a generally lower hydroxyl content, so the methane (CH4) adsorption capacity of coal declines, which promotes CH4 desorption. The control effect of pore structures after acidization reactions on CH4 desorption was revealed from perspectives of the diffusion coefficient (Kn), adsorption volume (ω), average pore-throat ratio (PT), and average sinuosity (τav). That is, CH4 molecules in tectonic coal after acidization turn from Knudsen diffusion to transitional diffusion, the adsorption volume of CH4 molecules shrinks, the average pore-throat ratio decreases, and the average sinuosity reduces, which promotes CH4 desorption from tectonic coal.

High-Performance Aqueous Zinc-Ion Batteries Based on Multidimensional V2 O3 Nanosheets@Single-Walled Carbon Nanohorns@Reduced Graphene Oxide Composite and Optimized Electrolyte.

The drawbacks of poor electronic conductivity and structural instability during the cycling process limit the electrochemical property of vanadium-based cathode materials for aqueous zinc-ion batteries. In addition, continuous growth and accumulation of zinc dendrites can puncture the separator and cause an internal short circuit in the battery. In this work, a unique multidimensional nanocomposite is designed by a facile freeze-drying method with subsequent calcination, consisting of V2 O3 nanosheets and single-walled carbon nanohorns (SWCNHs) crosslinked together and wrapped by reduced graphene oxide (rGO). The multidimensional structure can largely enhance the structural stability and electronic conductivity of the electrode material. Besides, additive Na2 SO4 in the ZnSO4 aqueous electrolyte not only prevents the dissolution of cathode materials but also suppresses the Zn dendrite growth. After considering the influence of additive concentration on ionic conductivity and electrostatic force for electrolyte, V2 O3 @SWCNHs@rGO electrode delivers a high initial discharge capacity of 422 mAh g-1 at 0.2 A g-1 and a high discharge capacity of 283 mAh g-1 after 1000 cycles at 5 A g-1 in 2 m ZnSO4 + 2 m Na2 SO4 electrolyte. Experimental techniques reveal that the electrochemical reaction mechanism can be expressed as the reversible phase transformation between V2 O5 and V2 O3 with Zn3 (VO4 )2 .

Decomposition and Reconstruction of Human Palm Movements.

OBJECTIVE: The human hand is known to have excellent manipulation ability compared to other primate hands. Without the palm movements, the human hand would lose more than 40% of its functions. However, uncovering the constitution of palm movements is still a challenging problem involving kinesiology, physiology, and engineering science. METHODS: By recording the palm joint angles during common grasping, gesturing, and manipulation tasks, we built a palm kinematic dataset. Then, a method for extracting the eigen-movements to characterize the common motion correlation relationships of palm joints was proposed to explore the palm movement constitution. RESULTS: This study revealed a palm kinematic characteristic that we named the joint motion grouping coupling characteristic. During natural palm movements, there are several joint groups with a high degree of motor independence, while the movements of joints within each joint group are interdependent. Based on these characteristics, the palm movements can be decomposed into seven eigen-movements. The linear combinations of these eigen-movements can reconstruct more than 90% of palm movement ability. Moreover, combined with the palm musculoskeletal structures, we found that the revealed eigen-movements are associated with joint groups that are defined by muscular functions, which provided a meaningful context for palm movement decomposition. CONCLUSION: This paper suggests that some invariable characteristics underlie the variable palm motor behaviors and can be used to simplify palm movement generation. SIGNIFICANCE: This paper provides important insights into palm kinematics, and helps facilitate motor function assessment and the development of better artificial hands.

Evolution of fissures and pressure discharge of gas caused by mining of the upper protective layer of a coal seam.

The evolution of fissures and permeability associated with mining of the upper protective layer of the coal seam is crucial for pressure relief gas drainage of the underlying seam. To understand the influence of mining the upper protective layer on gas drainage within the underlying coal seam, this study utilized the M16 and M18 seams in the Qinglong Coal Mine in Guizhou. Theoretical analysis, discrete element numerical simulation, and field tests were used to characterize the evolution of fractures associated with mining of the upper protective layer and the effects of pressure relief gas drainage within the protected coal seam. The results show that mining-related stress changes controlled the development of fractures, altering the permeability values of coals. An analysis of the crack development in the coal mass caused by mining of the upper protective layer shows that during the initial stage of mining, the produced cracks exhibited a butterfly shape network. Yet, with further development of the mining, these cracks and the stress changes gradually produced an inverted butterfly shape network. According to simulations, the areas of maximum deformation via expansion in the protected coal seam were located near the open cut and the mining end line of the working face. The maximum deformation values were 29.06 and 26.68 mm, respectively, and the corresponding deformation rates were 9.37‰ and 8.61‰, which are greater than the required 3‰. The findings of this study provide a new reference for gas control in pressure relief coal seams under similar working conditions.

A Single-dose, Two-Period Crossover Bioequivalence Study Comparing Two Liraglutide Formulations in Healthy Chinese Subjects.

Liraglutide, a glucagon-like peptide 1 receptor agonist, is indicated as an adjunct to diet and exercise to improve glycemic control in patients with type 2 diabetes. The original liraglutide products are costly, which limits patient access to this therapeutic treatment. Herein, a biosimilar was developed that is highly similar to the reference drug in molecular structure and bioactivity, and is expected to have similar pharmacokinetic (PK) and safety profiles in clinical studies. This study aimed to primarily evaluate the bioequivalence of 2 liraglutide formulations and secondarily assess their safety in healthy Chinese subjects following a single-dose subcutaneous injection. Thirty-two healthy volunteers were recruited in this randomized, open-label, single-dose, 2-period crossover bioequivalence study (ChiCTR2100043348). The geometric mean ratios (GMRs) of the test drug to the reference drug (T/R) and corresponding 90% confidence intervals (CIs) for maximum concentration (Cmax ) and the area under the concentration-time curve from time 0 to the time of the last quantifiable concentration (AUC0-t ) were estimated using a mixed-effects model, and bioequivalence was determined to have been achieved if the 2-sided 90%CI fell within the predefined range of 80%-125%. PK parameters were comparable between T and R, with GMRs of T/R for Cmax and AUC0-t being 105.7% and 107.7%, respectively, the 90%CI of which met the acceptance criteria for bioequivalence. We also observed a similar and favorable safety profile in the T and R arms, with adverse events being predominantly mild in severity and of gastrointestinal origin. Our findings indicate that the test drug is safe and well tolerated, bioequivalent to the reference drug, and warrants further testing in a phase III clinical trial.

Emission characteristics and influencing mechanisms of PAHs and EC from the combustion of three components (cellulose, hemicellulose, lignin) of biomasses.

Biomass burning is an important source of polycyclic aromatic hydrocarbons (PAHs) and elemental carbon (EC), but the formation mechanisms are still unclear. Cellulose, hemicellulose, and lignin are the three major components of biomass. In this study, the three-components extracted from three typical biomass raw materials were used for laboratory combustion experiments, to investigate the differences in the emission factors and chemical compositions of PAHs and EC. The average emission factors of the 16 kinds of PAHs were showing as lignin (135 ± 180 mg/kg) > cellulose (97.8 ± 124 mg/kg) > hemicellulose (48.9 ± 65.2 mg/kg), and the average emission factors of EC presented in the descending order of cellulose (1.65 ± 3.02 g/kg), lignin (1.30 ± 1.04 g/kg), and hemicellulose (0.450 ± 0.480 g/kg), respectively. The proportion of naphthalene emitted from cellulose and hemicellulose combustion is higher, while fluoranthene and pyrene accounted significantly higher proportion for lignin. Moreover, the influence of ignition temperature and oxygen content on the emission characteristics of PAHs and EC were also discussed. The influence of ignition temperature on the emission of EC and PAHs is more significant compared to oxygen content, because it obviously promoted the PAHs and EC formations through resonance-stabilized hydrocarbon-radical chain reaction (RSR) pathway. However, correlation analysis combined with cluster analysis showed that the RSR-pathway probably had different effects on PAH growth for the three-components, as the indene-involved RSR-pathway were mainly related to 4-6 ring PAHs for cellulose and lignin (except fluoranthene and pyrene), but 2-4 ring PAHs for hemicellulose. We also found that the fitted results according to the proportion of three-components were significantly higher than the measured values of raw materials for indene, medium-molecular-weight PAHs, and soot-EC. These results presented the different formation pathways for medium-molecular-weight PAHs and the two EC components emitted by biomass combustion, which are worthy of further studies in exploring the generation mechanisms of PAHs and EC.

VO2·0.26H2O nanobelts@reduced graphene oxides as cathode materials for high-performance aqueous zinc ion batteries.

A simple microwave-assisted hydrothermal approach is adopted to synthesize VO2·0.26H2O nanobelts@reduced graphene oxide (VO2·0.26H2O@rGO), which is regarded as a promising cathode material for ZIBs. Compared to VO2·0.26H2O, VO2·0.26H2O@rGO has a large specific surface area and low charge transfer resistance, improving its electrochemical properties. The large lattice spacing, high capacitive Zn2+ storage behavior, fast Zn2+ transfer rate and stable structure are also responsible for the performance.